Engineering Commons^™

Integration Of Energy Storage Components With Cascaded H-Bridge Multilevel Converters, Jingsheng Liao

Doctoral Dissertations

"In recent years, multilevel converters have gained considerable attention in medium-voltage motor drive and grid applications. This popularity is owed to their reduced voltage stress on the semiconductor devices used in their structure. In addition, multilevel converters generate near sinusoidal outputs with low harmonic distortions. Other advantages of such converters include inherent modularity and low dv/dt stresses. In general, multilevel power electronic converters are classified into three main topologies: diode-clamped, flying-capacitor, and cascaded H-bridge. A cascaded H-bridge multilevel converter is created when several H-bridge cells are placed in series. Each H-bridge cell must be fed by a stiff voltage source. …

Imaging Of Buried Utilities By Ultra Wideband Sensory Systems, Arun Prakash Jaganathan

Doctoral Dissertations

Third-party damage to the buried infrastructure like natural gas pipelines, water distribution pipelines and fiber optic cables are estimated at $10 billion annually across the US. Also, the needed investment in upgrading our water and wastewater infrastructure over the next 20 years is estimated by Environmental Protection Agency (EPA) at $400 billion, however, non-destructive condition assessment technologies capable of providing quantifiable data regarding the structural integrity of our buried assets in a cost-effective manner are lacking. Both of these areas were recently identified several U.S. federal agencies as 'critical national need'. In this research ultra wideband (UWB) time-domain radar technology …

A Finite Difference Method For Studying Thermal Deformation In Three-Dimensional Thin Films Exposed To Ultrashort Pulsed Lasers, Suyang Zhang

Doctoral Dissertations

Thermal analysis related to ultrashort-pulsed lasers has been intensely studied in science and engineering communities in recent years, because the pulse duration of ultrashort-pulsed lasers is only the order of sub-picoseconds to femtoseconds, and the lasers have exclusive capabilities in limiting the undesirable spread of the thermal process zone in the heated sample. Studying the thermal deformation induced by ultrashort-pulsed lasers is essential for preventing thermal damage. For the ultrashort-pulsed laser, the thermal damage is different from that caused by the long pulsed lasers and cracks occur after heating.

This dissertation presents a new finite difference method for studying thermal …

Tin Dioxide Nanoparticle Based Sensor Integrated With Microstrip Antenna For Passive Wireless Ethylene Sensing, Mercyma Deeba Balachandran

Doctoral Dissertations

In this dissertation, we present the development and integration of a passive ethylene gas sensor with triangular microstrip patch antenna for wireless monitoring of climacteric fruit freshness. The existing ethylene sensors are mostly SnO2 resistor based active sensors, fabricated on rigid substrates requiring high fabrication temperatures and cannot be used for wireless applications. The proposed passive ethylene gas sensor is a novel nanoparticle based SnO2 capacitive sensor which, unlike the other existing SnO2resistor based active thick film and thin film sensors, consists of 10 nm to 15 nm SnO2 nanoparticles coated as a thin dielectric film of 1300 nm thickness. …

Nanoengineered Templates For Controlled Delivery Of Bioactive Compounds, Nalinkanth Ghone Veerabadran

Doctoral Dissertations

The significance of any drugs, therapeutic proteins, or any bioactive compounds, is based not only on their effects on diseases but also on how specifically, how readily, how controllable and how prolonged their effects on the disease without having any side effects. Thus the techniques involved in the drug encapsulation and its controlled release for a longer duration of time form one of the important processes of drug reformulation. In recent years nanoparticles have created overwhelming attention for delivering drugs by nanoencapsulation. The smaller size of nanoparticles has longer circulation time and higher cellular uptake when compared with larger size …

A Simulation Of The Neural Action Potential Under The Influence Of Acetylcholinesterase Inhibitors Modeled In The Neuromuscular Junction, Frank Jenkins

Doctoral Dissertations

The rise of terrorism has created an interest in better ways to detect when humans are exposed to neurotoxins, especially nerve gases developed for military use, most of which are acetylcholinesterase inhibitors. Many current methods of detection are based on mass spectrometry, a method that is cumbersome and not particularly robust when used as an early warning method. The detection of acetylcholinesterase inhibitors would benefit from a combined model of the processes occurring in the neuromuscular junction between the presynaptic action potential and the motor end-plate action potential that includes the kinetics of acetylcholine and acetylcholinesterase in the synaptic cleft. …

Poly(Ethylenedioxythiophene) Based Electronic Devices For Sensor Applications, Jie Liu

Doctoral Dissertations

Organic electronic devices, based on Poly (3,4-ethylenedioxythiophene)-Poly (styrene sulfonic acid) (PEDOT-PSS) as the active layer for sensor applications, have been studied. Two sets of sensors have been developed. In one case, sensors consisting of PEDOT-PSS resistors have been realized and demonstrated for soil moisture monitoring. The resistor model for the soil moisture sensor enables the sensor device to be fabricated at low cost and easily tested with a simple structure. Unlike the large dimension device used in Time Domain Reflectometry (TDR), the sensors are small and are capable of capturing microscale behavior of moisture in soil which is useful for …

Wireless Sensor Network Modeling Using Modified Recurrent Neural Network: Application To Fault Detection, Azzam Issam Moustapha

Doctoral Dissertations

Wireless Sensor Networks (WSNs) consist of a large number of sensors, which in turn have their own dynamics. They interact with each other and the base station, which controls the network. In multi-hop wireless sensor networks, information hops from one node to another and finally to the network gateway or base station. Dynamic Recurrent Neural Networks (RNNs) consist of a set of dynamic nodes that provide internal feedback to their own inputs. They can be used to simulate and model dynamic systems such as a network of sensors.

In this dissertation, a dynamic model of wireless sensor networks and its …

Fabrication Of Bioactive Osteogenic Controlled-Release Systems, Cellular Platforms, And Cellular Capsules Using Layer -By -Layer Nanoassembly, Skylar Stewart-Clark

Doctoral Dissertations

There is an ever-increasing awareness that the field of tissue engineering offers many potential solutions to clinical problems. While advances along these lines have been made, the design and implementation of an "off the shelf" tissue is yet to be realized. Thus, the objectives of this work were largely aimed at the design and fabrication of biocompatible, bioactive structures which could be integrated into existing biomaterial products.

The electrostatic layer-by-layer (LbL) self-assembly technique was used to incorporate biologically relevant molecules within controlled release systems, cell culture platforms, and 3-D cellular capsules. Two delivery systems were investigated to determine the release …

Acquisition Of Cardiac Control Parameters From Whole Vagus Nerve Recordings, Marcia A. Pool

Doctoral Dissertations

Heart rate varies continuously depending on the amount of activity being performed or the emotional state of an individual. Both branches of the autonomic nervous system work to alter heart rate depending on the needs of the body. While healthy individuals are capable of altering their heart rate, individuals with certain types of heart disease do not have this ability. For these individuals, cardiac pacemakers are used to alter heart rate. Cardiac pacemakers use sensors to determine the pacing frequency for the heart; however, there is no current optimum sensor. In order to discover a better sensor, this study investigated …

Addressing Nonlinear Combustion Instabilities In Highly Dilute Spark Ignition Engine Operation, Brian C. Kaul

Doctoral Dissertations

"Dilute operation is a promising approach for increasing spark-ignition engine efficiency, in the form of either lean burn (air dilution) or EGR (inert dilution). High levels of charge dilution, however, lead to cyclic variability that is largely deterministic in nature. The determinism and nonlinear nature of the system indicate that it should be possible to reduce the cycle-to-cycle variations by implementing an electronic controller. Several needs arise when considering the development of such a controller. Three topics of interest are covered herein. First, a method of analysis for nonlinear dynamical systems is applied to engine data in order to estimate …

Unsteady Flow And Heat Transfer In Periodic Complex Geometries For The Transitional Flow Regime, Li-Kwen Chen

Doctoral Dissertations

"Diesel engines are facing significant challenges with upcoming changes in emissions standards. In general, meeting the increased emission standards will require a larger fraction of the engine heat rejection to occur in the vehicle cooling system. For certain applications, the surface geometry must also be such that it resists particulate fouling, precluding common interrupted surfaces such as louvered fins. Although acceptable continuous surface geometries such as bumped fin geometries are in use, the impacts of changing the parameters of this geometry are unknown. This study investigates the transport characteristics of bumped fins in the transitional flow regime using unsteady multi-dimensional …

Speculation And Hedging With Virtuals, Prasenjit Shil

Doctoral Dissertations

"Virtual bid" and "Virtual offer" are purely financial products offered in certain electricity markets. Theoretically, virtual bids and offers can change the electricity price as the bids and offers are stacked along with the demand and supply, respectively. This dissertation discusses how virtuals can be used to hedge and speculate in the electricity market. A statistical simulation model is developed based on the day-ahead (DA) demand and real time (RT) load data from Midwest Independent Transmission System Operator's (MISO) footprint and DA and RT price observed at Cinergy hub. The simulation models are intended to mimic the load and price …

Design And Optimization Of Abrasive Slurry Feed System, Control Circuit And Jet Drilling Tool For Mining Applications,, Pradeep Nambiath

Doctoral Dissertations

"This dissertation focused on an investigation of small diameter hole drilling using abrasive slurry jet (ASJ) technology. The existing ASJ feed systems were reviewed and found inadequate to satisfy the requirements of an ASJ drill. A novel feed system was designed which improved on existing systems by resolving problems with the inability to perform stop/start operations and ensure precise metering of abrasive feed. This system met standards of consistency and evenness of feed required for machining aircraft component parts for Air Force Research Laboratory (AFRL). Theoretical and experimental analysis of the power of an ASJ stream yielded valuable design information …

Enabling Wind Turbine Generators To Participate In Power Grid Frequency Regulation For Enhanced Stability, Hongtao Ma

Doctoral Dissertations

"This dissertation focuses on wind farm frequency regulation capability to maintain the grid frequency stability. Wind plant power controllers are designed and tested for participation in grid frequency restoration. The small signal stability on sub-optimal operating points is analyzed and a de-loaded operating point is proposed.

In the first paper, a new frequency regulation scheme is developed for the wind turbine/generator/converter trio that will provide the capability to participate in restoring frequency in a way similar to the droop response of conventional generators. Output active power adjustment can be realized by both converter and pitch angle control in addition to …

Integrated Process Planning For A Hybrid Manufacturing System, Lan Ren

Doctoral Dissertations

"A hybrid manufacturing system integrated CNC machining and laser-aided layered deposition and achieves the benefits of both processes. In this dissertation, an integrated process planning framework which aims to automate the hybrid manufacturing process is investigated. Critical components of the process planning, including 3D spatial decomposition of the CAD model, improvement of the toolpath generation pattern, repairing strategies using a hybrid manufacturing system, etc., are discussed"--Abstract, page iv.

Modeling And Rendering For Development Of A Virtual Bone Surgery System, Qiang Niu

Doctoral Dissertations

"A virtual bone surgery system is developed to provide the potential of a realistic, safe, and controllable environment for surgical education. It can be used for training in orthopedic surgery, as well as for planning and rehearsal of bone surgery procedures...Using the developed system, the user can perform virtual bone surgery by simultaneously "seeing" bone material removal through a graphic display device, "feeling" the force via a haptic deice, and "hearing" the sound of tool-bone interaction"--Abstract, page iii.

Predicting And Reducing Warranty Costs By Considering Customer Expectation And Product Performance, Naresh Kumar Sharma

Doctoral Dissertations

"This dissertation develops from quality loss function to warranty loss function in which customer expectation is also considered to be a variable. First, Taguchi's quality loss function for the larger-the-better case, which is different from the smaller-the better and nominal-the-best cases, has been assimilated into the other two by introducing a term called the target-mean ratio. Further topics addressed include the implications of a finite target on the classification of LTB characteristics, a new concept of a "Complementary Characteristic", operating window, complexity, and SN ratio based on complexity. A warranty is a buyer's confidence owing to the seller's assurance to …

System And Ic Level Analysis Of Electrostatic Discharge (Esd) And Electrical Fast Transient (Eft) Immunity And Associated Coupling Mechanisms, Jayong Koo

Doctoral Dissertations

"The exposure of electronic circuits to lightning, electrostatic discharge (ESD), electrical fast transients (EFT) or sine wave signals can reveal RF immunity problems. Typical problems include temporary malfunctions or permanent damage of integrated circuits (ICs). In an effort to reproduce those disturbances, a series of electromagnetic compatibility standards has been developed. However, a complete understanding of the root cause of the immunity problems has yet to be established. This dissertation discusses immunity problems in three papers, starting at the system level, via the coupling path into the IC"--Abstract, page iv.

Design And Evaluation Of A Virtual Reality Training System For New Underground Rockbolters, David Nutakor

Doctoral Dissertations

"The need for development of better training techniques for underground rock bolters is signified by the fact that a large number of experienced miners (Baby Boomers) will be retiring soon. This means that there will be very little interface time between the new miners and the experienced miners, which could have been used for training the new inexperienced miners. A new generation of workers (Nexters), who have grown up with computers and video games will replace the Baby Boomers, and the most efficient way to introduce them to the safety and health issues of the mining industry is to use …

Energy Efficient Wireless Sensor Network Protocols For Monitoring And Prognostics Of Large Scale Systems, James W. Fonda

Doctoral Dissertations

"In this work, energy-efficient protocols for wireless sensor networks (WSN) with applications to prognostics are investigated. Both analytical methods and verification are shown for the proposed methods via either hardware experiments or simulation. This work is presented in five papers. Energy-efficiency methods for WSN include distributed algorithms for i) optimal routing, ii) adaptive scheduling, iii) adaptive transmission power and data-rate control"--Abstract, page iv.

Modeling And Simulations Of Diphasic Composites For Development Of High Energy Density Dielectrics, Sandeep K. Patil

Doctoral Dissertations

"This research is focused on diphasic dielectric composites for high energy density storage applications in pulsed power and power distribution systems. Composite materials are particularly attractive because they can synergistically combine high permittivity with high breakdown strength of the individual phases. Energy density, which captures permittivity and dielectric breakdown strength as vital material parameters, dominates this research challenge. Avenues for increasing the effective permittivity and breakdown strength may be found by gaining fundamental understanding of the response of diphasic dielectrics to an applied electric field. Improved understanding of these characteristics will ultimately lead to dielectrics with increased energy storage densities. …

Multiple-Input Multiple-Output Wireless Communications With Imperfect Channel Knowledge, Christopher Potter

Doctoral Dissertations

"In the first work a recurrent neural network (RNN) is employed for MIMO channel prediction. A novel PSO-EA-DEPSO off-line training algorithm is presented and is shown to outperform PSO, PSO-EA, and DEPSO. This predictor is shown to be robust to varying channel scenarios. New expressions for the received SNR, array gain, average probability of error, and diversity gain are derived. Next, a new expression for the outage capacity of a MIMO system with no CSI at the transmitter and an estimate at the receiver is presented. Since the outage capacity is a function of the first and second moments of …

Thin Film Techniques For The Fabrication Of Nano-Scale High Energy Density Capacitors, James N. Reck

Doctoral Dissertations

Dielectric thin films of either TiO₂ or BaTiO₃ were sputtered in O₂/Ar plasmas on Si wafers to thicknesses ranging from approximately 25 to 200 nm with patterned Ni or Pt electrodes sputtered in Ar plasmas at thicknesses from about 20 to 250 nm to form nano-capacitors. Statistical design of experiments (DOE) was used to determine the effects of the deposition power, plasma composition, and deposition temperature on the measured electrical properties of the nano-capacitors. Additional tests to determine the effects of the dielectric and electrode thickness on the measured dielectric responses of the devices were also undertaken. Characterization was performed …

Geological Sequestration Of Carbon Dioxide By Hydrous Carbonate Formation In Steelmaking Slag, C. Hank Rawlins

Doctoral Dissertations

"The formation of carbonate solids from the alkaline earth oxide phases in steelmaking slag was investigated in dry and aqueous conditions as a vehicle for carbon dioxide sequestration. The goal of this research was to determine the process conditions that would increase the kinetics of the carbonate formation process under hydrous conditions, enabling direct removal of carbon dioxide from steelmaking offgas"--Abstract, page iv.

Physical Modeling Of Railroad Ballast Using The Parallel Gradation Scaling Technique Within The Cyclical Triaxial Framework, Adam F. Sevi

Doctoral Dissertations

"Due to the difficulties involved with testing large particle granular materials such as rockfill and railroad ballast, several methods of testing scaled down model specimens have been introduced. Of these techniques, the parallel gradation model has been found to be most useful. The parallel gradation model states that a smaller grainsize distribution model granular material, of the same composition as the prototype material, can be used in triaxial testing at a scaled down grainsize, if the model materials grainsize is exactly parallel to the prototype material. Therefore, a model granular material composed of a smaller, but parallel, grainsize distribution can …

Inter-Area Oscillation Damping In Large Scale Power Systems With Unified Power Flow Controllers, Mahyar Zarghami

Doctoral Dissertations

"Power system oscillations occur in power networks as a result of contingencies such as faults or sudden changes in load or generation. They are detrimental to the operation of the system since they affect system stability and the optimal power flow through it. These oscillations do not usually damp out in tie-lines unless certain controls are applied to the system. Local and inter-area oscillations have traditionally been controlled by Power System Stabilizers (PSS). However, Flexible Alternating Current Transmission Controllers (FACTS) have significant potential as alternatives to PSS. The main goal of this research is to damp inter-area oscillations by Unified …

Modeling, Analysis And Experimentation For Building Ice Parts With Supports Using Rapid Freeze Prototyping, Frances D. Bryant

Doctoral Dissertations

"Rapid Freeze Prototyping (RFP) is a freeform fabrication method that freezes water droplets into ice in a layer-by-layer manner to additively create a 3-dimensional part. Each layer of a geometry is deposited and allowed to freeze before the next layer is added. Ice parts produced by RFP can be used in investment casting to replace wax patterns and in other applications which may benefit from the unconventional method of using ice as a pattern or mold. More recently, a sacrificial support material has been incorporated into RFP so that over-hung areas and complex geometries can be fabricated. The research presented …

Virtual Prototyping With Surface Reconstruction And Freeform Geometric Modeling Using Level-Set Method, Weihan Zhang

Doctoral Dissertations

"More and more products with complex geometries are being designed and manufactured by computer aided design (CAD) and rapid prototyping (RP) technologies. Freeform surface is a geometrical feature widely used in modern products like car bodies, airfoils and turbine blades as well as in aesthetic artifacts. How to efficiently design and generate digital prototypes with freeform surfaces is an important issue in CAD. This paper presents the development of a Virtual Sculpting system and addresses the issues of surface reconstruction from dexel data structures and freeform geometric modeling using the level-set method from distance field structure. Our virtual sculpting method …

Densification, Microstructure, And Mechanical Properties Of Zirconium Diboride Based Ultra-High Temperature Ceramics, Sumin Zhu

Doctoral Dissertations

"The first part of this dissertation was aimed at studying the densification of ZrB₂ ceramics by pressureless sintering techniques. Various processes have been applied to coat ZrB₂ powders with polymer precursors, which were used to produce C after charring. After sintering at 1900⁰C, relative density increased of ~70% for uncoated ZrB₂ to >99% for ZrB₂ coated with at least 1.0 wt% C. Thermodynamic analysis suggested that C reacted with and removed oxide impurities (ZrO₂ and B₂O₃) that were present on the ZrB₂ particle surfaces, which promoted densification by minimizing grain coarsening"--Abstract, page iv.