Engineering Commons^™

Modeling Of Non-Uniform Hydrodynamics And Catalytic Reaction In A Solids-Laden Riser, Rajeshkumar Patel

Dissertations

The riser reactors are widely used in a variety of industrial applications such as polymerization, coal combustion and petroleum refinery because of the strong mixing of gas and solids that yields high heat and mass transfer rates, and reaction rates. In a Fluid Catalytic Cracking (FCC) process, the performance of riser reactor is strongly dependent on the interaction between the fluid and catalysts, since the reaction takes place on the active surface of the catalysts. This is why, the local coupling between hydrodynamics and reaction kinetics is critical to the development of riser reaction models. The local gas-solids flow structure …

Design Of Single-Carrier Frequency Domain Equalization (Sc-Fde) With Transmit Diversity For Wireless And Optical Communications, Kodzovi Acolatse

Dissertations

As the demand of wireless service is rising, there is a need to transmit high-speed packets over the wireless communication channel. Broadband data transmission over wireless channels commonly faces the challenges of multipath fading channels, which are both time and frequency selective. There is then a need to design transmission techniques that can combat the adverse effects of the channel, and enable reliable high data rate wireless services. Orthogonal frequency division multiplexing (OFDM) has become widely accepted primarily because of its robustness against frequency selective fading channels, but it suffers a number of drawbacks such as high peak-to-average power ratio …

Risk Based Models For The Optimization Of Oil And Gas Supply Chain Critical Infrastructure, Kingsley Oseloka Achebe

Dissertations

The oil and gas sector faces a broad array of risks and uncertainties, affecting short- and long-term planning, and causing adverse effects in the energy sector. To predict and minimize them, risk based supply chain models were developed for the oil and gas supply chain critical infrastructure.

First, the events and activities were categorized as short term and long term, and their risk ratings derived, by analyzing data from past events and site visits. The result showed that events like the Israel – Arab war, successful hurricane, and production increase or decrease, had a risk rating of approximately 7.

Second, …

Modeling Of Equilibrium Point Trajectory Control In Human Arm Movements, Kai Chen

Dissertations

The underlying concept of the Equilibrium Point Hypothesis (EPH) is that the CNS provides a virtual trajectory of joint motion, representing spacing and timing, with actual movement dynamics being produced by interactions of limb inertia, muscle viscosity and speed/position feedback from muscle spindles. To counter criticisms of the EPH, investigators have proposed the use of complex virtual trajectories, non-linear damping, stiffness and time varying stiffness to the EPH model. While these features allow the EPH to adequately produce human joint velocities, they conflict with the EPH’s premise of simple pre-planned monotonic control of movement trajectory. As a result, this study …

Factors That Impact Seat Belt Usage And Injury Severity Of Belted Front Seat Occupants, Siri Konje Lawrencia Nukenine

Dissertations

Factors influencing seat belt usage have been extensively researched in the safety analysis literature. Most of this research has focused on factors that influence seat belt usage for a driver and front seat passenger in a vehicle. Few research studies have investigated factors that impact seat belt usage for back seat occupants. This research investigates the factors associated with seat belt usage for front-seat as well as backseat occupants of vehicles in the state of New Jersey. Using logistic regression, seat belt usage models were developed to examine the contribution of several variables on seat belt usage for five vehicle …

Application Of Mass/Stiffness Eccentricity To Control Response Of Structures Subjected To Earthquake Ground Motion, Bakhtiar Feizi

Dissertations

This dissertation is driven by the concept that engaging more modes in the response of structures can be used to mitigate its translational dynamic response. One such an approach is to engage torsional modes through engineered eccentricity (mass/stiffness eccentricity), thus, introducing coupled translation-rotation response. This idea was first introduced in a paper published by MacBain and Spillers in 2004. As a follow up to the same idea this dissertation was an attempt to investigate and develop the theory concerning the application of mass/stiffness eccentricity to control the translational motion of structures subjected to earthquake ground motion.

Different discrete and continuous …

Study Of Mechanisms Of Phytotoxicity Of Alumina Nanoparticles, Anthony Elijius

Dissertations

Plant growth inhibitory effect of alumina nanoparticles has recently been reported (Ling Y, Watts D, 2004) but the mechanisms of such an effect are yet to be established. The phytotoxicity of aluminum and some of its compounds is well known, but the rapid expansion of nanotechnology resulting in the introduction of new sets of materials in the nanometer range has led to the development of new approaches, experimental methods and modes of investigation.

In this study, the observed phytotoxic effects of alumina nanoparticles suspension on five plant species (Zea mays, Cucumis sativus, Daucus carota, Brassica oleracea, Lactuca sativa) …

Mixing Of Nanosize Particles By Magnetically Assisted Impaction Techniques, James V. Scicolone

Dissertations

Nanoparticles and nanocomposites offer unique properties that arise from their small size, large surface area, and the interactions of phases at their interfaces, and are attractive for their potential to improve performance of drugs, biomaterials, catalysts and other highvalue- added materials. However, a major problem in utilizing nanoparticles is that they often lose their high surface area due to grain growth. Creating nanostructured composites where two or more nanosized constituents are intimately mixed can prevent this loss in surface area, but in order to obtain homogeneous mixing, de-agglomeration of the individual nanoparticle constituents is necessary.

Due to high surface area, …

Tin/Hfo2/Sio2/Si Gate Stacks Reliability : Contribution Of Hfo2 And Interfacial Sio2 Layer, Nilufa Rahim

Dissertations

Hafnium Oxide based gate stacks are considered to be the potential candidates to replace SiO₂ in complementary metal-oxide-semiconductor (CMOS), as they reduce the gate leakage by over 100 times while keeping the device performance intact. Even though considerable performance improvement has been achieved, reliability of high-κ devices for the next generation of transistors (45nm and beyond) which has an interfacial layer (IL: typically SiO₂) between high-κ and the substrate, needs to be investigated. To understand the breakdown mechanism of high-κ/SiO₂ gate stack completely, it is important to study this multi-layer structure extensively. For example, (i) the …

Distributed Synchronization Algorithms For Wireless Sensor Networks, Nicola Varanese

Dissertations

The ability to distribute time and frequency among a large population of interacting agents is of interest for diverse disciplines, inasmuch as it enables to carry out complex cooperative tasks. In a wireless sensor network (WSN), time/frequency synchronization allows the implementation of distributed signal processing and coding techniques, and the realization of coordinated access to the shared wireless medium. Large multi-hop WSN's constitute a new regime for network synchronization, as they call for the development of scalable, fully distributed synchronization algorithms. While most of previous research focused on synchronization at the application layer, this thesis considers synchronization at the lowest …

Model Reference Control For Ultra-High Precision Positioning Systems, Lan Yu

Dissertations

Due to the increasing demands of high-density semiconductors, molecular biology, optoelectronics, and MEMS/NEMS in the past decades, control of ultra-high precision positioning using piezoelectricity has become an important area because of its high displacement resolution, wide bandwidth, low power consumption, and potential low cost. However, the relatively small displacement range limits its application. This work proposed a practical ultra-high precision piezoelectric positioning system with a complementary high displacement range actuation technology. Solenoids are low cost, high speed electromagnetic actuators which are commonly used in on-off mode only because of the inherent high nonlinear force-stroke characteristics and unipolar forces (push/pull) generated …

Study Of Controlled Release Of Active Pharmaceutical Ingredients From Functionalized Nanoclays And Polymer Matrices, Jin Uk Ha

Dissertations

This dissertation contains the results of three related novel investigations in the field of structure-property-processing relationships of pharmaceutical polymer-based products. They are: a) modification of a pharmaceutical anionic nanoclay with two different Active Pharmaceutical Ingredients (APIs) to produce nanohybrid API carriers intended to be used alone or in acrylic polymer matrices, b) comparison of binary systems containing the above APIs in the selected acrylic polymers in terms of their miscibilities with the polymer, but in the absence of nanoclay, and c) comparison of the polymer/API binary systems with ternary polymer/API/Clay systems.

For the first study, the calcination method which can …

Underwater Communication Via Particle Velocity Channels : Principles, Channel Models, And System Design, Huaihai Guo

Dissertations

A vector sensor is capable of measuring important non-scalar components of the acoustic field such as the particle velocity, which cannot be obtained by a single scalar pressure sensor. In the past few decades, extensive research has been conducted on the theory and design of vector sensors. On the other hand, underwater acoustic communication systems have been relying on scalar sensors only, which measure the pressure of the acoustic field. By taking advantage of the vector components of the acoustic field, such as the particle velocity, the vector sensor can be used for detecting the transmitted data. In this dissertation, …

Seismic Characterization Of Recycled Aggregate Concrete, Amin Jamali

Dissertations

There are significant environmental benefits of recycling waste concrete and reusing it as aggregate for structural concrete, but the use of Recycled Aggregate Concrete (RAC) is yet limited to non-structural applications such as road sub-base. Widespread application of RAC in areas such as seismic design requires an improved knowledge of RAC behavior under multiaxial state of stresses.

The main objective of this research is the characterization of seismic properties of RAC by developing a stress-strain model which can reasonably describe the behavior under both unconfined and confined conditions. An extensive experimental program, including testing of several plain RAC cylinders as …

Developing Anaerobic Digestion Cooperatives In Ireland, Aoife Ní Ruanaigh, John Mcgrory

Dissertations

Anaerobic Digestion (AD) is a natural process of decomposition and decay that takes place in the absence of oxygen and by which organic matter is broken down to its simpler chemical components. AD plants could help Ireland meet its requirements under a number of EU Directives as landfills release far more greenhouse gas emissions than other forms of waste treatment. It is estimated that 37 million tonnes per year of animal manure are stored on farms before disposal. There are also 676,000 tonnes of municipal food and garden waste produced annually. This waste could be used in AD plants to …

Ductile Mode Material Removal Of Ceramics And Semiconductors, Deepak Ravindra

Dissertations

Ceramics and semiconductors are hard, strong, inert and lightweight. They also have good optical properties, wide energy bandgap and high maximum current density. This combination of properties makes them ideal candidates for tribological, semiconductor, MEMS and optoelectronic applications respectively. Manufacturing these materials without causing surface and subsurface damage is extremely challenging due to their high hardness, brittle characteristics and poor machinability. However, ductile regime machining of these materials is possible due to the high-pressure phase transformation occurring in the material caused by the high compressive stresses induced by the single point diamond tool tip. In this study, to further augment …

Development Of Energy Absorbing Laminated Fiberglass Composites Using Electrospun Glass Nanofibers, Evan Kimbro

Dissertations

The ability to predict failure of composite laminates due to delaminations is critical because of its subsurface nature. Traditional strengthening methods such as stitching and Z-pinning, while improving interlaminar properties in woven composites, lead to a reduction of the in-plane properties. Electrospun non-woven sheets of nanofibrous mat applied at interfacial regions offer an option to traditional treatments. Applications where protrusion energy must be dissipated completely would benefit the most from the use of the electrospinning treatment. Examples are bullet proof vests and vehicle armor. Penetration of a projectile through a composite material may be avoided by creating more energy absorbent …

Variable Block Size Motion Compensation In The Redundant Wavelet Domain, Ahmed Abdelgadir Suliman

Dissertations

Video is one of the most powerful forms of multimedia because of the extensive information it delivers. Video sequences are highly correlated both temporally and spatially, a fact which makes the compression of video possible. Modern video systems employ motion estimation and motion compensation (ME/MC) to de-correlate a video sequence temporally. ME/MC forms a prediction of the current frame using the frames which have been already encoded. Consequently, one needs to transmit the corresponding residual image instead of the original frame, as well as a set of motion vectors which describe the scene motion as observed at the encoder. The …

Reduced-Order Equivalent-Circuit Models Of Thermal Systems Including Thermal Radiation, Serap Karagol

Dissertations

We established a general, automatic, and versatile procedure to derive an equivalent circuit for a thermal system using temperature data obtained from FE simulations. The EC topology was deduced from the FE mesh using a robust and general graph-partitioning algorithm. The method was shown to yield models that are independent of the boundary conditions for complicated 3D thermal systems such as an electronic chip. The results are strongly correlated with the geometry, and the EC can be extended to yield variable medium-order models. Moreover, a variety of heat sources and boundary conditions can be accommodated, and the EC models are …

Performance Analysis Of Batch Reactor Temperature Control Systems, Michael Healy, John Mcgrory

Dissertations

The aim of this project was to investigate the performance of a number of key control strategies in the temperature control of batch reactors. A bench scale model was built and a batch production system was then implemented on this model. As there was no a priori knowledge of the system a number of common system identification methods were investigated.  The system was controlled using a Mitsubishi FX(2)N Programmable Logic Controller which was interfaced with a PC running ICONICS, a Supervisory Control And Data Acquisition software package. The system identification methods produced two different models for the system and …

The Application Of Fuzzy Logic In Determining Linguistic Rules And Associative Membership Functions For The Control Of A Manufacturing Process, Marcus Foley, John Mcgrory

Dissertations

Fuzzy logic is a form of multi-valued logic derived from fuzzy set theory. Its methodology aims to provide a definitive solution from information that may be construed as ambiguous, imprecise or noisy. Classical set theory studies the properties of sets, while fuzzy set theory investigates the degree to which an element can be related to a set. The aim of this project is to develop a control strategy for a specific technical challenge relating to the food processing sector based on the deployment of fuzzy logic control concepts. Specifically, in this paper the author is concerned with the ability to …

Simulation Of Reverse Flow Heat Recovery For Pharmaceutical Clean Rooms In Colombia, Sandra Juliana Olaya Pineda, John Mcgrory

Dissertations

This dissertation examines, analyses, implements, and evaluates an innovative software heat transfer model for predicting air-to-air heat (energy) recovered in pharmaceutical drying clean rooms in Colombia. The approach provides a synergy between Reverse Flow Heat Recovery technology and activities for the consumption of this energy, not solely within the process, but throughout the whole pharmaceutical complex (e.g. warehouse, office and alternative processes). This novel integrated modelling tool developed using off the shelf software application such as MS Excel combined with MS Visual programming to calculate psychometric points, mass and enthalpy balances for analysing the operation of heat recovery systems. This …

The Synthesis And Host-Guest Applications Of Synthetic Receptor Molecules, Zachary Richard Osner

Dissertations

Host-guest chemistry involves the complimentary binding between two molecules. Host molecules have been synthesized to bind negative, positive, and neutral molecules such as proteins and enzymes, and have been used as optical sensors, electrochemical sensors, supramolecular catalysts, and in the pharmaceutical industry as anti-cancer agents.1 The field of nanoscience has exploited guest-host interactions to create optical sensors with colloidal gold and Dip-Pen nanolithography technologies. Gold nanoparticles, have been functionalized with DNA, and have been developed as a selective colorimetric detection system, that upon binding turns the solution from a red to blue in color.2

Cyclotriveratrylene (CTV) 1 is a common …

Beading And Dimpling Techniques To Improve The Vibration And Acoustic Characteristics Of Plate Structures, Nabeel Taiseer Alshabtat

Dissertations

A method of improving the vibroacoustic characteristics of beams and plates is presented. This method is based on creating dimples or beads on the surface of the structures. The proposed method couples the finite element method with an optimization technique based on the genetic algorithm (GA). The improvement of the vibroacoustic characteristics of beams and plates is achieved by two separate strategies. The first strategy is optimizing the natural frequencies of beams and plates. The second strategy is minimizing the sound radiation from such vibrating structures. Optimizing the natural frequencies of some types of beams and simply supported plates by …

Cross-Layer Design For Mobile Ad-Hoc Unmanned Aerial Vehicle Communication Networks, Abdel Ilah Nour Alshbatat

Dissertations

Mobile Ad-Hoc network (MANET) is a popular type of wireless network that is formed by a collection of mobile nodes. Each node in such a network has the capability to communicate with its neighbors and non-neighbors through a wireless medium without using any existing network infrastructure. Due to the lack of infrastructure, all nodes in Ad-Hoc network are designed to act as an end system and a router for other nodes.

Traditionally, the dominant design methodology for network protocols was based on the open systems interconnection (OSI) reference model. This methodology divided the stack into seven layers in which each …

A Study To Determine The Influence Of Workload On Nursing Personnel, Supreeta G. Amin

Dissertations

The alarming number of adverse medical events and associated costs have placed immense importance toward the safety and health of both patients and medical personnel. A shrinking nurse workforce, an aging patient and nursing population coupled with a mismatch between hospital demands and the available nursing staff have created a situation detrimental to both patient and nursing personnel. Long working hours, working more than one job, low staffing ratios, high patient acuity, minimal social support, low experience level, complicated equipment, complex procedures and varying workload are some factors that may have a negative impact on the quality of care provided …

New Media Icc Profiles Construction And Concerns, Reem El Asaleh

Dissertations

With the advent of the modern digital technology, users can now capture an image and reproduce it between different media, such as display it on LCD monitor or tablet computer, print it on desktop printer or send it to a printing press. The challenge has been then to maintain the accuracy of image colors during this reproduction, which has led to the development of Color Management Systems. Using these systems, the color reproduction across-media will be accomplished using device ICC profiles that describe each device’s color characterization data in a standardized format based on International Color Consortium (ICC) specifications.

ICC …

Leach-Sm: A Protocol For Extending Wireless Sensor Network Lifetime By Management Of Spare Nodes, Bilal Abu Bakr

Dissertations

Operational lifetime of a wireless sensor network (WSN) depends on its energy resources. Significant improvement of WSN lifetime can be achieved by adding spare sensor nodes to WSN. Spares are ready to be switched on when any primary (a node that is not a spare) exhausts its energy. A spare replacing a primary becomes a primary itself.

The LEACH-SM protocol (Low-Energy Adaptive Clustering Hierarchy with Spare Management) proposed by us is a modification of the prominent LEACH protocol. LEACH extends WSN lifetime via rotation of cluster heads but allows for inefficiencies due to redundant sensing target coverage. There are two …

Direct Forcing And Heating Immersed Boundary- Lattice Boltzmann Method For Arterial Wall Thermography, Oluyinka Olugbenga Bamiro

Dissertations

Vulnerable atherosclerotic plaques have high probability of rupture and are characterized by non-homogenous temperature along the arterial wall. The nonhomogeneous temperature is attributed to the accumulation of heat releasing inflammatory cells in the arterial wall. Rupture of the vulnerable plaque can lead to acute coronary syndrome and sudden cardiac death. Arterial wall thermography (AWT) can be applied to detect the presence of temperature hot spots along the arterial wall by using temperature measurement devices and provide an early detection of a vulnerable atherosclerotic plaque. AWT, however, is invasive in nature.

Computational fluid and heat transport models provide a more efficient …

Benefits Of Cpfr And Vmi Collaboration Strategies In A Variable Demand Environment, Dattaraj Kamalapurkar

Dissertations

In recent years, practitioners and academic researchers have emphasized that organizations need to collaborate with suppliers and customers to improve their competitive advantage. The availability of cost efficient information technologies like EDI, XML, etc. have made it possible to develop and implement many forms of collaboration strategies. Among them, Vendor Managed Inventory (VMI) and Collaborative Planning, Forecasting and Replenishment (CPFR) are most popular, which are considered for this study. While many studies have identified the benefits of demand information sharing in supply chains; however the benefits gained by implementing collaboration strategies like VMI and CPFR in a variable demand environment …