Engineering Commons^™

Determination Of Reliable Fatigue Life Predictors For Magnetorheological Elastomers Under Dynamic Equi-Biaxial Loading, Yangen Zhou, Liang Jiang, Shaojuan Chen, Jianwei Ma, Tony Betts, Stephen Jerrams

Articles

Fatigue life prediction is of great significance in ensuring magnetorheological elastomer (MRE) based rubber components exhibit reliability and do not compromise safety under complex loading and this necessitates the development of plausible fatigue life predictors for MREs. In this research, silicone rubber based MREs were fabricated by incorporating soft carbonyl iron magnetic particles. Equi-biaxial fatigue behaviour of the fabricated MREs was investigated by using the bubble inflation method. The relationship between fatigue life and maximum engineering stress, maximum strain and strain energy density were studied. The results showed that maximum engineering stress and stored energy density can be used as …

Risk Registers: Structuring Data Collection To Develop Risk Intelligence, Maria Chiara Leva, Nora Balfe, B. Mcaleer, M. Rock

Articles

This paper presents the results of the development and implementation of a company-wide risk register, based on a clear set of data structures. A case study from an electricity generation company is presented and the process followed is described. The results of the case study indicated areas where the concept of risk registers could be extended to make better use of existing data and to support continuous improvement of risk management. Six key areas are discussed (1) aggregation of risks across the business, (2) supporting controls over mitigation measures, (3) improved estimation of event likelihood, (4) integrating with critical asset …

Precision Control Of Flow Rate In Microfluidic Channels Using Photoresponsive Soft Polymer Actuators, Colm Delaney, Peter Mccluskey, Simon Coleman, Jeffrey Whyte, Nigel Kent, Dermot Diamond

Articles

A novel approach that allows control of flow in microfluidic channels with unsurpassed performance using light is described. Valve structures have been created using photoresponsive hydrogels based on spiropyran-functionalised pNIPAAm hydrogels photopolymerised around pillar structures within the channels. Valve actuation is controlled from outside the fluidic system using externally located LEDs. Highly precise and accurate flow rates can be selected by passing real-time flow rate measurements into a PID algorithm. The optimised algorithm also minimises overshoot of the selected flow rate, eliminates flow rate drift, and improves the system response time. In addition to the dramatic improvements in flow rate …

A Correction Current Injection Method For Power Flow Analysis Of Unbalanced Multiple-Grounded 4-Wire Distribution Networks, Keith Sunderland, M. Coppo, Michael Conlon, R. Turri

Articles

Power flow analysis of distribution networks incorporating LV consumer representation needs to be cognizant of an unbalanced load structure and the grounding network between the consumer and network operator (TNC-S earthing). In this paper, the asymmetrical 3-phase (and neutral) power flow problem is solved by a correction current injectionmethodology applied to a system represented by a complex admittance matrix. The correction current injection technique is adopted to adjust the power exchange of shunt elements, whose nominal admittances are included in the system admittance matrix, through suitable fringing currents in the iteration process. This methodology offers an improved and more …

Operational Analysis Of Improved Γ-Z-Source Inverter With Clamping Diode And Its Comparative Evaluation, Zeeshan Aleem, Moin Hanif

Articles

Due to a substantial shortage of conventional energy sources, the utilization of renewable energy is gaining attention. Power converters form interfaces to provide power from renewable energy sources to end user systems. Impedance-source inverters (ZSIs) have become a research hotspot and are widely used to overcome the drawbacks of conventional voltage-source inverters and current-source inverters such as two-stage power conversion and less immunity to electromagnetic interference noises. This paper presents various transformer-based ZSIs mainly classified as trans-ZSIs, improved trans-ZSIs, inductor-capacitor-capacitor transformer ZSI, TZSIs, and their comparisons with a new family of ZSIs called Γ-Z-source inverters (ΓZSI). Full operational analysis of …

A Fast Linear Electro-Optical Effect In A Non-Chiral Bent-Core Liquid Crystal, Yuri Panarin, S.P. Sreenilayam, J.K. Vij, A. Lehmann, C. Tschierske

Articles

We report the observation of an electro-optical effect for a linear rotation of the optical axis as function of the electric field in an achiral tilted bent-core liquid crystalline compound, in which 4-cyanoresorcinol bisbenzoate core is symmetrically terminated by long linear alkyl chains (n =16) on both ends. The linear electro-optic effect observed in this material is similar to the deformed helical ferroelectric liquid crystal (DHFLC) effect reported previously in a FLC material except that dimensions of the helical pitch differ by two orders of magnitude. In the chiral systems, the helical pitch usually lies on the scale of sub-optical …

A Geo-Statistical Investigation Of Agricultural And Infrastructural Risk Factors Associated With Primary Verotoxigenic E. Coli (Vtec) Infection In The Republic Of Ireland, 2008–2013, Paul Hynds, Jean O'Dwyer, Una B. Fallon, Coilín Oscar Óhaiseadha

Articles

Ireland reports the highest incidence of verotoxigenic Escherichia coli (VTEC) infection in Europe. This study investigated potential risk factors for confirmed sporadic and outbreak primary VTEC infections during 2008-2013. Overall, 989 VTEC infections including 521 serogroup O157 and 233 serogroup O26 were geo-referenced to 931 of 18488 census enumeration areas. The geographical distribution of human population, livestock, unregulated groundwater sources, domestic wastewater treatment systems (DWWTS) and a deprivation index were examined relative to notification of VTEC events in 524 of 6242 rural areas. Multivariate modelling identified three spatially derived variables associated with VTEC notification: private well usage (odds ratio (OR) …

Carbon Nanomaterials And Their Application To Electrochemical Sensors: A Review, Aoife Power, Shaneel Chandra, Brian Gorey, James Chapman

Articles

Carbon has long been applied as an electrochemical sensing interface owing to its unique electrochemical properties. Moreover, recent advances in material design and synthesis, particularly nanomaterials, has produced robust electrochemical sensing systems that display superior analytical performance. Carbon nanotubes (CNTs) are one of the most extensively studied nanostructures because of their unique properties. In terms of electroanalysis, the ability of CNTs to augment the electrochemical reactivity of important biomolecules and promote electron transfer reactions of proteins is of particular interest. The remarkable sensitivity of CNTs to changes in surface conductivity due to the presence of adsorbates permits their application as …

An Enhanced Spring-Particle Model For Red Blood Cell Structural Mechanics: Application To The Stomatocyte–Discocyte– Echinocyte Transformation, Mingzhu Chen, Fergal Boyle

Articles

Red blood cells (RBCs) are the most abundant cellular element suspended in blood. Together with the usual biconcave-shaped RBCs, i.e., discocytes, unusual-shaped RBCs are also observed under physiological and experimental conditions, e.g., stomatocytes and echinocytes. Stomatocytes and echinocytes are formed from discocytes and in addition can revert back to being discocytes; this shape change is known as the stomatocyte–discocyte–echinocyte (SDE) transformation. To-date, limited research has been conducted on the numerical prediction of the full SDE transformation. Spring- particle RBC (SP-RBC) models are commonly used to numerically predict RBC mechanics and rheology. However, these models are incapable of predicting the full …

Precise Flow-Control Using Photo-Actuated Hydrogel Valves And Pid-Controlled Led Actuation, Colm Delaney, Simon Coleman, Jeff Whyte, Nigel Kent, Dermot Diamond

Articles

Herein we demonstrate remarkable control of flow within fluidic channels using photo-actuated hydrogel valves. By polymerizing the valves in situ it has been possible to create highly reproducible valves. Through the use of an LED platform and a PID algorithm we have generated extremely accurate flow control and created prototype devices to document their potential application within the microfluidics field.

3d Printing Aids Acetabular Reconstruction In Complex Revision Hip Arthroplasty, Andrew J. Hughes, Cathal Debuitleir, Philip Soden, Brian O'Donnchada, Anthony Tansey, Ali Abdulkarim, Colm Mcmahon, Conor J. Hurson

Articles

Revision hip arthroplasty requires comprehensive appreciation of abnormal bony anatomy. Advances in radiology and manufacturing technology have made three-dimensional (3D) representation of osseous anatomy obtainable, which provide visual and tactile feedback. Such life-size 3D models were manufactured from computed tomography scans of three hip joints in two patients. The first patient had undergone multiple previous hip arthroplasties for bilateral hip infections, resulting in right-sided pelvic discontinuity and a severe left-sided posterosuperior acetabular deficiency. The second patient had a first-stage revision for infection and recurrent dislocations. Specific metal reduction protocols were used to reduce artefact. The images were imported into Materialise …

Stochastic Modelling For Levy Distributed Systems, Jonathan Blackledge, T Raja Rani

Articles

The purpose of this paper is to examine a range of results that can be derived from Einstein’s evolution equation focusing on (but not in an exclusive sense) the effect of introducing a L´evy distribution. In this context, we examine the derivation (as derived from the Einstein’s evolution equation) of the classical and fractional diffusion equations, the classical and generalised Kolmogorov-Feller equations, the evolution of self-affine stochastic fields through the fractional diffusion equation and the fractional Schr¨odinger equation, the fractional Poisson equation (for the time independent case), and, a derivation of the Lyapunov exponent. In this way, we provide a …

Aphonic: Adaptive Thresholding For Noise Cancellation In Smart Mobile Environments, Ruairí De Fréin

Articles

We propose a signal-channel, adaptive threshold selection technique for binary mask construction, namely APHONIC, (AdaPtive tHreshOlding for NoIse Cancellation) for smart mobile environments. Using this mask, we introduce two noise cancellation techniques that perform robustly in the presence of real-world interfering signals that are typically encountered by mobile users: a violin busker, a subway and busy city square sounds. We demonstrate that when the power of the time-frequency components of the voice of a mobile user does not significantly overlap with the components of the interference signal, the threshold learning and noise cancellation techniques significantly improve the Signal-to-Interference Ratio (SIR) …

Probabilistics Risk Assessment Of Power Quality Variations And Events Under Temporal And Spatial Characteristic Of Increased Pv Integration In Low Voltage Distribution Networks, Shivananda Pukhrem, Malabika Basu, Michael Conlon

Articles

Integration of PVDG reduces the voltage unbalance as compared with no or low PVDG penetration. There is a higher probability of observing deep sag at the site as PVDG integration increases. This probabilistic approach can be used as a tool to assess the likely impacts due to PVDG integration against the worst-case scenarios.

Dye-Sensitised Solar Cell Antenna, Oisin O'Conchubhair, Patrick Mcevoy, Max Ammann

Articles

Dye-sensitised solar cells are proposed as a solarantenna in the form of a proof-of-concept dipole operating at 1.1 GHz. Comprised of glass plates in basic rectangular shapes, various material properties are considered for impact on antenna performance at three phases of assembly. Simulated and empirical analyses indicate how such low-cost solar cells can also realise viable concurrent antenna designs.

An Analysis Of Harmonic Heating In Smart Buildings And Distribution Network Implications With Increasing Non-Linear (Domestic) Load And Embedded Generation, Chittesh Veni Chandran, Keith Sunderland, Malabika Basu

Articles

Harmonic distortion is generally not taken into account within domestic installations and the associated wiring systems, as its potential is considered sufficiently small to be neglected. Standards to limit harmonic manifestations in the low voltage (LV) network are available, but these can be breached as a consequence of advancements in power electronics in some modern household devices contributing higher levels of harmonic distortion than permitted. While these devices individually might not be considered serious in terms of system level harmonic distortion manifestations, electrical equipment failures and insulation failures - increasingly being derived from harmonic cable heating - suggest a different …

Adaptive Linear Prediction For Optimal Control Of Wind Turbines, Mahinsasa Narayana, Keith Sunderland, Ghanim Putrus, Michael Conlon

Articles

In order to obtain maximum power output of a Wind Energy Conversion System (WECS), the rotor speed needs to be optimised for a particular wind speed. However, due to inherent inertia, the rotor of a WECS cannot react instantaneously according to wind speed variations. As a consequence, the performance of the system and consequently the wind energy conversion capability of the rotor are negatively affected. This study considers the use of a time series Adaptive Linear Prediction (ALP) technique as a means to improve the performance and conversion efficiency of wind turbines. The ALP technique is introduced as a real …

Enhanced Network Voltage Management (Nvm) Techniques Under The Proliferation Of Rooftop Solar Pv Installation In Low Voltage Distribution Network (Lvdn), Shivananda Pukhrem, Malabika Basu, Michael Conlon, Keith Sunderland

Articles

Proliferation of rooftop solar PV distributed generator (PVDG) installation in low voltage distribution network (LVDN) imposes voltage fluctuation challenges that are a threat to distribution system operators. Reactive power control (RPC) methods are insufficient in isolation to combat the overvoltage fluctuations manifested in LVDN with significant grid-tied PVDG installations. Whereas active power curtailment (APC) control can alleviate the voltage fluctuation in such situations and it is achieved at the cost of reduced active power injection. This paper explores how deficiencies in both RPC and APC as separate approaches can be mitigated by suitably combining RPC and APC algorithms. Strategies combining …

Development Of Ferroelectricity In The Smectic Phases Of 4-Cyanoresorcinol Derived Achiral Bent-Core Liquid Crystals With Long Terminal Alkyl Chains, Sithara Pavithran Sreenilayam, J. K. Vij, Yuri Panarin, Anne Lehman

Articles

Bent-core molecules can form numerous polar and symmetry broken liquid crystalline phases with fascinating properties. Here we report the characteristics of a previously unknown polar synclinic smectic phase, Sm C S P X , found in the phase sequence of an achiral bent-core material with a 4-cyanoresorcinol bisbenzoate core, terminated by long linear alkyl chains ( n = 18 ) on both ends. This phase exists over a narrow range of temperatures and is sandwiched in between the random polar synclinic smectic phase ( Sm C S P R ) and polar synclinic ferroelectric ( Sm C S P F …

Design And Investigation Of De Vries Liquid Crystals Based On 5-Phenyl-Pyrimidine And (R,R)-2,3-Epoxyhexoxy Backbone., S.P. Sreenilayam", D. Rodriguez-Lojo, V. P. Panov, V. Swaminathan, J. K. Vij, Yuri Panarin, E. Gorecka, A. Panov, P.J. Stevenson

Articles

Calamitic liquid crystals based on 5-phenyl-pyrimidine derivatives have been designed, synthesized, and characterized. The 5-phenyl pyrimidine core was functionalized with a chiral (R,R)-2,3-epoxyhexoxy chain on one side and either siloxane or perfluoro terminated chains on the opposite side. The one involving a perfluorinated chain shows SmA^{*} phase over a wide temperature range of 82 °C, whereas the siloxane analog exhibits both SmA^{*} and SmC^{*} phases over a broad range of temperatures, and a weak first-order SmA^{*}-SmC^{*} transition is observed. For the siloxane analog, the reduction factor for the layer shrinkage R (relative to its thickness at the SmA^{*}-SmC^{*} transition temperature, …

The Different Stages Of Prpd Pattern For Negative Point To Plane Corona Driven By A Dc Voltage Containing A Ripple, Tobias Dezenzo, Thomas Betz, Andreas Schwarzbacher

Articles

This paper presents the different patterns, which can be observed by means of a phase resolved partial discharge analysis, when a negative dc voltage is applied to a point to plane arrangement in air. The required phase relation is obtained due to the ripple being present on the dc voltage generated by a half-wave rectification. Phase resolved partial discharge patterns are given from corona onset to glow inception. Discharge pulses appearing at the test object are used to support physical explanations of the pattern occurrence. It is shown that five clearly identifiable patterns accompany the evolution of corona discharges when …

Miniaturized Dual-Band Antenna Array With Double-Negative (Dng) Metamaterial For Wireless Applications, Abdulrahman Shueai Mohsen Alqadami, Mohd Faizal Jamlos, Ping Jack Soh, Sharul Kamal Abdul Rahim, Guy Vandenbosch, Adam Narbudowicz

Articles

A miniaturized dual-band antenna array using a negative index metamaterial is presented for WiMAX, LTE, and WLAN applications. This left-handed metamaterial plane is located behind the antenna array, and its unit cell is a combination of split-ring resonator, square electric ring resonator, and rectangular electrical coupled resonator. This enables the achievement of a metamaterial structure exhibiting both negative permittivity and permeability, which results in antenna size miniaturization, efficiency, and gain enhancement. Moreover, the proposed metamaterial antenna has realized dual-band operating frequencies compared to a single frequency for normal antenna. The measured reflection coefficient (S11) shows a 50.25% bandwidth in the …

Development And Characterisation Of A Bath-Based Vertical Blackbody Cavity Calibration Source For The Range −30 °C To 150 °C, Sam Boles, Igor Pušnik, Dubhaltach Mac Lochlainn, David Fleming, Izabela Naydenova, Suzanne Martin

Articles

Industrial use of Radiation Thermometers (RTs) is becoming increasingly common due to the perceived advantages and wide market availability. Blackbody Cavity Radiation Sources (BCRSs) are typically used for calibration of these instruments, and these cavities are oriented horizontally in most cases. For BCRSs based in thermal baths, this necessitates the use of custom-built baths with side openings. This paper presents a unique design of vertical bath-based BCRS that may be immersed in conventional calibration baths without modifications to the baths. The method, results, and analysis of an international comparison comparing this vertical BCRS, standard horizontal BCRSs, and a previous iteration …

Directional Modulation For Compact Devices, Adam Narbudowicz, Max Ammann, Dirk Heberling

Articles

A new directional modulation system which uses radiation pattern data for modulation encoding is proposed. The approach allows compact multiport antennas (e.g. MIMO capable antennas) to be used for directional modulation, replacing extensive arrays. The modulation weighting coefficients are calculated with a fixed, antenna specific equation, thus reducing computational complexity. The solution is intended to enhance privacy in small, battery-operated wireless devices, required for “Internet of Things” applications.

Design Of A Compact, Fully-Autonomous 433 Mhz Tunable Antenna For Wearable Wireless Sensor Applications, John Buckley, Kevin Mccarthy, Domenico Gaetano, Loizos Loizou, Brendan O'Flynn, Cian O'Mathuna

Articles

The authors present the design of a tunable 433 MHz antenna that is tailored for wearable wireless sensor applications. This study first presents a detailed analysis of the measured impedance characteristics of a chosen antenna under test (AUT) in varying proximity to a human test subject. Instead of limiting the analysis to the head and hand only, this analysis measures the AUT impedance at varying distances from 11 different body positions. A novel antenna equivalent circuit model is then developed that enables both the free-space and total on-body AUT impedance variation to be rapidly computed using a circuit simulator instead …

Assessment Of Mental Workload: A Comparison Of Machine Learning Methods And Subjective Assessment Techniques, Karim Moustafa, Saturnino Luz, Luca Longo

Articles

Mental workload (MWL) measurement is a complex multidisciplinary research field. In the last 50 years of research endeavour, MWL measurement has mainly produced theory-driven models. Some of the reasons for justifying this trend includes the omnipresent uncertainty about how to define the construct of MWL and the limited use of datadriven research methodologies. This work presents novel research focused on the investigation of the capability of a selection of supervised Machine Learning (ML) classification techniques to produce data-driven computational models of MWL for the prediction of objective performance. These are then compared to two state-of-the-art subjective techniques for the assessment …

Efficacy And Mechanistic Insights Into Endocrine Disruptor Degradation Using Atmospheric Air Plasma, Chaitanya Sarangapani, M. Danaher, Brijesh Tiwari, Peng Lu, Paula Bourke, Patrick J. Cullen

Articles

Endocrine disruptors are a class of contaminants found in water and process effluents at low concentrations. They are of concern due to their high estrogenic potency. Their presence in the environment has led to the search for effective techniques for their removal in wastewater. For this purpose, an atmospheric air plasma reactor was employed for the study of the degradation of three endocrine disruptor chemicals (EDC) namely; bisphenol A (BPA), estrone (E1) and 17β-estradiol (E2) within a model dairy effluent. Identification of the plasma induced active species both in the gas and liquid phases were performed. Also studied was the …

An Evaluation Of The Safety Of The Cycling In Dublin City For Dit Students, Niamh O' Reilly

Articles

Cycling as a mode of transport offers many benefits including a cheap, cost effective, healthy, fast, mainly congestion free and environmentally friendly means of getting to and from places of employment and education. Given the central location of Technological University Dublin campus buildings this would seem an ideal option for its third level students, but on the contrary, a DIT online travel survey conducted in March 2014 found that only 7% of students chose cycling as their primary mode of transport. Concerns about cyclist safety were a major factor cited by students who chose alternative modes of transport. Based on …

Bim Innovation Capability Programme: An Irish Bim Study, Barry Mcauley, Alan Hore, Roger West

Articles

In 2011 the Royal Institute of Architects Ireland (RIAI) conducted a survey which found that BIM adoption within Ireland was quite low at 16%. Over the last five years these figures have risen significantly, with the 2016 Irish Digital Transition Survey reporting that 76% of respondents possess confidence in their organisation’s BIM skills and knowledge. This represents a significant shift of BIM adoption in Ireland over the last five years.

The BIM Innovation Capability Programme (BICP) Irish BIM study, builds on the findings from the BICP Global BIM Study by providing an in depth review of BIM in Ireland with …

Microbial Enzyme Production Using Lignocellulosic Food Industry Wastes As Feedstock: A Review, Amit Jaiswal, Rajeev Ravindran

Articles

Enzymes are of great importance in the industry due to their substrate and product specificity, moderate reaction conditions, minimal by-product formation and high yield. They are important ingredients in several products and production processes. Up to 30% of the total production cost of enzymes is attributed to the raw materials costs. The food industry expels copious amounts of processing waste annually, which is mostlylignocellulosicin nature. Upon proper treatment,lignocellulosecan replace conventional carbon sources in media preparations for industrial microbial processes, such as enzyme production. However, wild strains of microorganisms that produce industrially important enzymes show low yield and cannot thrive on …