Engineering Commons^™

Reaction Of Liquid Aluminium- Samarium Alloys With B4c At Ultra High Temperatures, Sanjay Shantha-Kumar

Open Access Theses & Dissertations

Reactive studies between a packed bed of B4C and Al-Sm-Me (Me = Ti, Zr, Hf) alloy melts were carried out under a pseudo-isopiestic thermodynamic system. A graphite enclosure isolated the system under a temperature gradient with one end reaching temperatures greater than 1800 K and the opposite end of the graphite enclosure contains liquid Al with temperatures approximating 950 K. The liquid Al establishes an oxygen potential to control oxidation of very reactive elements (i.e., Al, Sm and Ti). The Al-Sm-Me alloy infuses into a packed bed of B4C reacting exothermically to form borides and carbides depending on the thermodynamic …

High Temperature Oxidation Of Nb-Cr-Mo-Si-B Alloys, Kathryn S. Thomas

Open Access Theses & Dissertations

It has been the trend to use nickel based superalloys in high temperature applications, however higher temperatures are required in the effort to enhance the efficiency of such components as jet turbine engines. The melting temperature of the nickel based superalloy limits the extent to which temperature can be raised as these materials are typically used at temperatures within 200 degrees of their melting point. Refractory metal based systems are attractive due to their high melting points, low densities, and good high temperature strength. However, in such cases as niobium, poor oxidation resistance limits the widespread use of such alloys. …

Single And Multiple Objective Biomass-To-Biofuel Supply Chain Optimization Considering Environmental Impacts, Claudia Evangelina Valles Sosa

Open Access Theses & Dissertations

Bioenergy has become an important alternative source of energy to alleviate the reliance on petroleum energy. Bioenergy offers diminishing climate change by reducing Green House Gas Emissions, as well as providing energy security and enhancing rural development. The Energy Independence and Security Act mandate the use of 21 billion gallons of advanced biofuels including 16 billion gallons of cellulosic biofuels by the year 2022. It is clear that Biomass can make a substantial contribution to supply future energy demand in a sustainable way. However, the supply of sustainable energy is one of the main challenges that mankind will face over …

Defeating Anisotropy In Material Extrusion 3d Printing Via Materials Development, Ángel Ramón Torrado Pérez

Open Access Theses & Dissertations

Additive Manufacturing technologies has been in continuous development for more than 35 years. Specifically, the later denominated Material Extrusion Additive Manufacturing (MEAM), was first developed by S. Scott Crump around 1988 and trademarked later as Fused Deposition Modeling (FDM). Although all of these technologies have been around for a while, it was not until recently that they have been more accessible to everyone. Today, the market of 3D printers covers all ranges of price, from very specialized, heavy and expensive machines, to desktop printers of only a few cubic inches in volume. Until recently, FDM technology had remained somewhat stagnant …

A Methodology For Physically-Based Contact And Meniscus Properties In Rigid-Body Computational Knee Modeling, Stephen Wilson

Open Access Theses & Dissertations

Determining natural inner knee mechanics is a longstanding goal for researchers with applications to prevention and treatment of knee trauma and osteoarthritis. Physical testing has only provided limited information of knee mechanics due to technical challenges and cost. Modeling has been used for decades to obtain some of this otherwise inaccessible information, and recently finite element analysis (FEA) has become a popular means to this end. However, FEA requires time intensive mesh-creation and has large computational requirements. Ideally, model creation should be easy and simulations should be fast to allow for sensitivity analysis. Although allowing easier model creation and offering …

Modeling Of The Response Of A Memcapacitor For An Impulse, Step, Ramp, And Sinusiodal Inputs, Ghassan Khalil Kachmar

Open Access Theses & Dissertations

Micro-Electro-Mechanical Systems, or MEMS, is a technology of very small scale devices. The dimensions of MEMS can vary from below one micron to several millimeters. MEMS have some mechanical functionalities such as the moving plate of a parallel plate capacitor (memcapacitor). MEMS researchers and developers have demonstrated an extremely large number of microsensors for almost every possible sensing modality including temperature, pressure, inertial forces, and chemical species. The equation of motion of the moving plate of a memcapacitor is governed by a non-linear differential equation with no known exact solution. Most research into determining the theoretical response of a memcapacitor …

Low Power Design Techniques For Data Acquisition, Praveen Kumar Palakurthi

Open Access Theses & Dissertations

Semiconductor technology advancement continues to lead to smaller device geometries. Digital circuits have benefited from the technology scaling whereas analog circuits often suffer in terms of performance and noise immunity. As functionality continues to be integrated onto systems-on-chips, analog circuits consume increasingly more power than digital circuits and the objective of this Dissertation is to explore low power techniques in the context of both digital and analog circuits residing on the same silicon real estate.

As natural signals are in analog form, a necessity exists to convert these into digital form and then back again in order to exploit the …

Spectral Radiation Analysis Of Premixed Oxy-Syngas And Oxy-Methane Flames, Naznin Jahan Afrose

Open Access Theses & Dissertations

Oxy-fuel combustion has potential to be an impeccable enhancement of current combustion techniques. For a hydrocarbon burning with oxygen the resulting exhaust stream is composed mainly of carbon dioxide and water vapor. This exhaust allows for easier carbon capture and sequestration since the water can be condensed out. Another advantage is the significant reduction of NOx since much of the nitrogen found in air-combustion systems is eliminated. These processes also provide a higher theoretical efficiency which is advantageous. Although beneficial many of the exhaust gas products radiative characteristics are unknown. Motivated by this, this paper focuses on the spectral radiation …

Hydrodynamic Cavitation As A Method For Cell Disruption, Christopher Caviglia

Open Access Theses & Dissertations

Development of new renewable technologies is an important driver in the scientific community.

As atmospheric carbon dioxide levels increase and the dependence on a finite amount of fossil fuel remains, the need for sustainable forms of energy is ever growing. Research in the field of renewable biofuels has pointed researchers toward the naturally occurring, robust, lipid- producing microorganism; microalgae. Its ability to sequester carbon and yield high lipid production has made it very attractive to renewable research. It has the potential to produce up to 10 times the oil, per acre, than competing biofuel feedstocks. However, an energy efficient method …

Design And Analysis Of A Novel Latch System Implementing Fiber-Reinforced Composite Materials, Francisco Guevara

Open Access Theses & Dissertations

The use of fiber-reinforced composite materials have increased in the last four decades in high technology applications due to their exceptional mechanical properties and low weight. In the automotive industry carbon fiber have become popular exclusively in luxury cars because of its high cost. However, Carbon-glass hybrid composites offer an effective alternative to designers to implement fiber-reinforced composites into several conventional applications without a considerable price increase maintaining most of their mechanical properties. A door latch system is a complex mechanism that is under high loading conditions during car accidents such as side impacts and rollovers. Therefore, the Department of …

Novel Engineered Nanomaterials For Water Remediation And Gas Adsorption: Graphene Oxide And Carbon Nanotubes Decorated With Metal-Organic Frameworks And Magnetic Nanoparticles, Vahid Jabbari

Open Access Theses & Dissertations

In the current study, a series of novel magnetic and non-magnetic hybrid nanocomposites based on metal-organic frameworks (MOFs) of M3(BTC)2 (M: Ni, Cu, Zn, and Cd), graphene oxide (GrO), and carbon nanotubes (CNTs), and Fe3O4 magnetic nanoparticles (MNPs) were developed via a green, simple and versatile solvothermal method at which GrO and CNT were used as platform to grow the MOFs and Fe3O4 MNPs over them. The as-synthesized nanocomposites were characterized by XRD, SEM, TEM, XPS, IR, Raman, TGA, and N2 adsorption/desorption isotherms. Morphological analysis confirmed successful growth of nano-size Fe3O4 MNPs and M3(BTC)2 MOFs over GrO and CNT platforms. …

A Cell Formation Algorithm For Sequential Processes With Alternative Machine Selection In The Automotive Lighting Industry, Victor Manuel Loya Garnica

Open Access Theses & Dissertations

At the present time, there are more than 12 big companies dedicated to design and produce OEM lighting systems for cars and trucks. The manufacturing processes for headlamps, tail lamps and any other exterior vehicle lighting are very common in the auto industry. Still, every automotive lamp assembly is different from brand to brand and even between the different vehicle models. Indeed, there are car headlamps with less than 30 sub-components and others with up to 300 elements. This implies creating diverse part numbers which share or hold varying manufacturing methods within a specific facility. Management of the plant resources …

E-Quality Design Of Experiments For Structural Electronics, Oscar Murga

Open Access Theses & Dissertations

Additive Manufacturing (AM) is a technology utilized for creating complex parts by adding layers of material in order to create a three dimensional functional part. This technology has been pushed to a new level of functionality where mechanical parts are combined with electronic components to create Three-Dimensional Structural Electronics (3DSE) systems. This new technology has been used to replace Printed Circuit Boards (PCB), for 3D SE are light weight and can be created in any desired shape. Computer Aided Design (CAD) software is used to design the part and a Fused Deposition Modeling (FDM) machine is used to 3D print …

A Methodology For Use Of Digital Image Correlation For Hot Mix Asphalt Testing, Estefany Ramos

Open Access Theses & Dissertations

Digital Image Correlation (DIC) is a relatively new technology which aids in the measurement of material properties without the need for installation of sensors. DIC is a noncontact measuring technique that requires the specimen to be marked with a random speckled pattern and to be photographed during the test. The photographs are then post-processed based on the location of the pattern throughout the test. DIC can aid in calculating properties that would otherwise be too difficult even with other measuring instruments.

The objective of this Thesis is to discuss the methodology and validate the use of DIC in different hot …

A Rapid Approach For Considering Nonlinear Response Of Flexible Pavements Under Fwd And Estimation Of Remaining Lives Of Pavements, Shahabaldin Shirazi

Open Access Theses & Dissertations

Most mechanistic empirical pavement analyses are based on the layered elastic models where the stress sensitivity of geomaterials and their nonlinearity are either ignored or accounted for indirectly. Advanced numerical models, such as finite element models, are required to consider the nonlinear nature of the geomaterials. Existing pavements are often tested with the Falling Weight Deflectometer (FWD) to estimate the input moduli to the layered elastic models in order to estimate remaining life and structural capacity of pavements. It has been more than 30 years that FWD tests are being performed to measure structural adequacy of pavements. Backcalculation is the …

Acoustic Emission Characteristics Of Damage Accumulation In Kevlar® 49 Composites, Eduardo Andrade

Open Access Theses & Dissertations

Acoustic emission (AE) data attained during tensile testing of epoxy impregnated Kevlar® 49 (K/Ep) composite strands were reduced and analyzed to monitor progressive damage accumulation during the approach to tensile failure. The K/Ep material tested in this study was chosen due to its similarity to the material-of-construction used in composite overwrapped pressure vessels (COPVs) used on the NASA Space Shuttle Orbiter. Insight into the progressive microstructural degradation of K/Ep strands was gained by monitoring AE event rate and energy. Source location based on energy attenuation and arrival time data was used to differentiate between significant AE attributable to microstructural damage …

Evaluating Methods Of Field-Based 3d Visualization And Their Application To Mapping Metamorphic Terranes: An Example From The Panamint Mountains, California, Jade Ashley Brush

Open Access Theses & Dissertations

Field geology has traditionally relied on 2D, paper-based workflows, but digital mapping techniques are rapidly replacing these outdated methods because they allow for more efficient and accurate mapping. This research applies digital mapping techniques and two terrestrially-based 3D visualization technologies, photogrammetry and Light Detection and Ranging (LiDAR), to the study of metamorphic terranes in the Panamint Mountains, California. This study reports on the spatial accuracy of TINs (triangulated irregular networks) generated from both photogrammetry and ground-based LiDAR using a terrestrial laser scanner (TLS) and discusses how spatial accuracy can be increased. Two levels of comparison were used to test spatial …

Evaluation Of Point Of Use Drinking Water Treatment Systems For Colonias In The Southwest United States, Isaac Campos Flores

Open Access Theses & Dissertations

Clean drinking water is often taken for granted in first world countries, such as the United States. However, thousands of colonias residents (settlements in the Southwest US that lack access to basic infrastructure) still lack access to clean drinking water. Such is the case in the Paso Del Norte Region. In Doña Ana County, NM, and El Paso County, TX, colonia residents typically rely on shallow domestic wells and hauled water, respectively. However, both water sources can pose health concerns from elevated total dissolved solids and microbiological contamination. With connection to centralized water treatment and distribution still years away, colonias …

Novel Endohedral Derivatives Of Sc3n@C2n (N = 34, 40) And Unique Tether Controlled Bis-Functionalization Of Fullerenes, Maira Raquel Ceron Hernandez

Open Access Theses & Dissertations

Since the discovery of fullerenes in 1985, their exohedral functionalization has been necessary to increase their solubility and explore their properties and potential applications in materials science and medicinal chemistry. This Thesis provides a short overview of the importance of electronic, size and shape complementarity in determining the structures of specific endohedral fullerene compounds. This is followed by a description of a new method for the separation of scandium nitride endohedral fullerenes Sc3N@C2n (n = 34, 39 and 40), and their monofunctionalization.

We also present the regioselective synThesis of easily isolable bis-derivatives of C60, C70, and M3N@Ih-C80 (M = Sc, …

Study Of A Directly Heated Oxy-Fuel Supercritical Power Generation System, A S M Arifur Rahim Chowdhury

Open Access Theses & Dissertations

The Directly heated supercritical oxy-fuel gas turbines have the potential to become an important addition to current power generation systems. They provide a higher thermal efficiency and more effective carbon capture techniques than existing gas turbines. Due to the higher density of the working fluids, the turbomachinery size in these systems can be reduced significantly; this will facilitate to minimize the operational cost. To achieve supercritical working fluid at the turbine inlet combustion needs to be conducted under enormous amounts of pressure; these values are is about 10 times those found in the present gas turbines. Additionally, existing material operational …

Re-Examining Resistance: Fan-Produced Queer Readings And Teen Wolf, Joshua J. Espinoza

Open Access Theses & Dissertations

MTV's popular television series, Teen Wolf (2011), has amassed a large online following of fans that create their own queer narratives through fan-fiction, subverting the show's hegemonic heteronormativity. Through a textual thematic analysis of Teen Wolf, this case study illustrates how online fandoms can subvert hegemony through queer readings of literary characters, resisting the dominant heteronormativity on network television. This article argues that rearticulating the showâ??s narratives into queer readings functions as a form of LGBT resistance, effectively counteracting the heteronormativity and hegemony portrayed on screen. This study examines how Teen Wolf approaches queer content, including homoeroticism and LGBT themes …

Transition States And Modeling For Co9s8/Mos2 Catalysis, Gabriel Angel Gonzalez

Open Access Theses & Dissertations

Transition state computational studies of the sulfur removal from dibenzothiophene (DBT) molecule have herein been performed considering the Co9S8/MoS2 interface existing on unsupported Co/MoS2 catalysts. The linear synchronous transit (LST) and quadratic synchronous transit (QST) methods integrated in a density functional theory (DFT) program such as Dmol3 were used for the calculations of energy barriers of the transition states. Three different configurations present on the Co9S8/MoS2 interface have been envisaged as possible catalytic sites: sulfur-sulfur (S, S) sites, and molybdenum-sulfur (Mo, S) and molybdenum-molybdenum (Mo, Mo) edge sites. This study revealed that the (Mo, Mo) edge site is the most …

An Improved Sin-Hyperbolic Constitutive Model For Creep Deformation And Damage, Mohammad Shafinul Haque

Open Access Theses & Dissertations

Inspection and maintenance of industrial gas turbines (IGTs) cost millions of dollars. Growing demand of obtaining higher IGT efficiency leads to higher temperature and pressure operating conditions. Long exposure of turbine components at elevated temperature and pressure

makes creep damage critically important to consider during planning, designing and operating conditions. Effective and economic maintenance requires accurate creep deformation, damage

evolution and rupture life prediction information. Creep prediction models are used to determine the state of the turbine components and to schedule the inspection, maintenance and replacement time periods. The more accurate the prediction model, the less is the overall cost …

High Temperature Helical Tubular Receiver For Concentrating Solar Power System, Nazmul Hossain

Open Access Theses & Dissertations

In the field of conventional cleaner power generation technology, concentrating solar power systems have introduced remarkable opportunity. In a solar power tower, solar energy concentrated by the heliostats at a single point produces very high temperature. Falling solid particles or heat transfer fluid passing through that high temperature region absorbs heat to generate electricity. Increasing the residence time will result in more heat gain and increase efficiency. A novel design of solar receiver for both fluid and solid particle is approached in this paper which can increase residence time resulting in higher temperature gain in one cycle compared to conventional …

Study Of Materials And Machines For 3d Printed Large-Scale, Flexible Electronic Structures Using Fused Deposition Modeling, Seyeon Hwang

Open Access Theses & Dissertations

The 3 dimensional printing (3DP), called to additive manufacturing (AM) or rapid prototyping (RP), is emerged to revolutionize manufacturing and completely transform how products are designed and fabricated. A great deal of research activities have been carried out to apply this new technology to a variety of fields. In spite of many endeavors, much more research is still required to perfect the processes of the 3D printing techniques especially in the area of the large-scale additive manufacturing and flexible printed electronics.

The principles of various 3D printing processes are briefly outlined in the Introduction Section. New types of thermoplastic polymer …

Design Of A High Intensity Turbulent Combustion System, Mohammad Arif Hossain

Open Access Theses & Dissertations

In order to design next generation gas turbine combustor and rocket engines, a systematic study of flame structure at high intensity turbulent flow is necessary. The fundamental study of turbulent premixed combustion has been a major research concern for decades. The work is focused on the design and development of a high intensity turbulent combustion system which can be operated at compressible (0.3 < M < 0.5), preheated (T0=500K) and premixed conditions in order to investigate the 'Thickened Flame' regime. An air-methane mixture has been used as the fuel for this study. An optically accessible backward-facing step stabilized combustor has been designed for a maximum operating pressure of 6 bar. A grid has been introduced with different blockage ratios (BR = 54%, 61% & 67%) in order to generate turbulence inside the combustor for the experiment. Optical access is provided via quartz windows on three sides of the combustion chamber. Finite Element Analysis (FEA) is done in order to verify the structural integrity of the combustor at rated conditions. In order to increase the inlet temperature of the air, a heating section was designed to use commercially available in-line heaters. Separate cooling subsystems have been designed for chamber cooling and exhaust cooling. The LabVIEW software interface has been selected as the control mechanism for the experimental setup. A 10 kHz Time Resolved Particle Image Velocimetry (TR-PIV) system and a 3 kHz Planer Laser Induced Fluorescence (PLIF) system have been integrated with the system in order to diagnose the flow field and the flame respectively. The primary understanding of the flow field inside the combustor was achieved through the use of Detached Eddy Simulation (DES) by using commercially available software package ANSYS FLUENT. Preliminary validation is done by 10 kHz TR-PIV technique. Both qualitative and quantitative analysis have been done for CFD and experiment. Major flow parameters such as average velocity, fluctuation of velocity, kinetic energy, and turbulent intensity have been calculated for two distinct Reynolds number (Re = 815 & 3500). PIV results are compared with CFD results which show significant agreement with each other.

Wind Farm Optimization Using Evolutionary Algorithms, Carlos Marco Ituarte-Villarreal

Open Access Theses & Dissertations

In recent years, the wind power industry has focused its efforts on solving the Wind Farm Layout Optimization (WFLO) problem. Wind resource assessment is a pivotal step in optimizing the wind-farm design and siting and, in determining whether a project is economically feasible or not. In the present work, three (3) different optimization methods are proposed for the solution of the WFLO: (i) A modified Viral System Algorithm applied to the optimization of the proper location of the components in a wind-farm to maximize the energy output given a stated wind environment of the site. The optimization problem is formulated …

Transition Metal Carbide (Tmc) Novel Materials For Novel Catalytic Applications, Svetlana Lagoykina

Open Access Theses & Dissertations

Transition metal carbides (TMC) constitute a diverse class of materials and traditionally have many technological applications. TMC became a subject of extensive research since 1973, when their platinum -like properties were discovered. They demonstrated high catalytical activity and selectivity in a variety of chemical reaction and have potential for some novel catalytic application.

This research is an effort to design new high effective, selective and stable bimetal or alkali promoted TMC catalyst. After extensive theoretical research a wide range of TMC, including bimetal and alkali promoted carbides, were synthesized by different methods. All solids were characterized by XRD and microscopy. …

Thermal Shock Studies On Carbon-Carbon Composites: Experimentation And Analysis, Alma Lucia Leanos

Open Access Theses & Dissertations

The oxidation behavior of C/C composites under thermal shock conditions in air is understood and predicted experimentally and by computational efforts. In Chapter. 1, both compressive properties and oxidation behavior of pristine and thermal shock exposed 2D C/C composite specimens were examined. Pristine test specimens were exposed to thermal shock conditions with temperatures ranging from 400°C to 1000°C in an oxidizing environment, followed by compression tests on pristine and thermal shock exposed specimens to obtain their compressive responses.

Similarly, in Chapter. 2, the influence of thermal shock conditions on both, the extent of carbon materials decomposition and the through-thickness compressive …

Computation Offloading Decisions For Reducing Completion Time, Salvador Melendez

Open Access Theses & Dissertations

Mobile devices are being widely used in many applications such as image processing, computer vision (e.g. face detection and recognition), wearable computing, language translation, and battlefield operations. However, mobile devices are constrained in terms of their battery life, processor performance, storage capacity, and network bandwidth. To overcome these issues, there is an approach called Computation Offloading, also known as cyber-foraging and surrogate computing. Computation offloading consists of migrating computational jobs from a mobile device to more powerful remote computing resources. Upon completion of the job, the results are sent back to the mobile device. However, a decision must be made; …