Engineering Commons^™

Optimization Of Sulfur Dioxide And Lactic Acid Steeping Concentrations For Wet-Milling Of Grain Sorghum, R. A. Buffo, Curtis L. Weller, A. M. Parkhurst

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Influence of sulfur dioxide (SO₂) and lactic acid (LA) on grain sorghum steeping efficiency in terms of wet-milling characteristics was investigated using response surface analysis. Tested ranges of concentrations in steeping water were 0.050 to 0.278% and 0 to 0.282% for SO₂ and LA, respectively. Measured wet-milling variables were steeping solids yield, starch yield, protein yield, fiber/germ yield, starch recovery, protein recovery and protein content of starch. Starch and protein recovery values were highly correlated to each other (r = 0.74). Correlations of these attributes with fiber/germ yield were strongly negative (r = –0.96 and r = …

Cast Films From Soy Protein Isolates And Fractions, L. A. Kunte, A. Gennadios, S. L. Cuppett, M. A. Hanna, Curtis L. Weller

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Glycerol-plasticized soy protein films were cast from alkaline aqueous film-forming solutions of laboratory-prepared 7S, 11S, and soy isolate (LSI) fractions and from commercial soy isolate (CSI). Tensile strength (TS), elongation at break (E), water vapor permeability (WVP), total soluble matter (TSM), protein solubility (PS), and Hunter L, a, and b color values of these films were determined. The 11S films had greater TS than 7S films (P < 0.05), while LSI films had greater TS than CSI films (P < 0.05). No significant differences were detected among mean E values and among mean WVP values of all films (P > 0.05). The 7S films had higher TSM and PS values than 11S films (P < 0.05). CSI films were significantly darker (lower L value) and more yellow (greater positive b value) than LSI films (P < 0.05).

Films From Laboratory-Extracted Sorghum Kafirin, Roberto A. Buffo, Curtis L. Weller, Aristippos Gennadios

Department of Agricultural and Biological Systems Engineering: Faculty Publications

There has been increased interest in development of biopolymer films and coatings from protein, polysaccharide, and lipid materials in recent years. The qualities of renewability, degradability, compostability, and edibility make such films particularly appealing for food and nonfood packaging applications. Moreover, wide commercialization of biopolymer films will provide a value-added innovative use for traditional agricultural commodities as sources of film-forming materials. Research findings on production, properties, and potential applications of edible films have been reviewed (Krochta 1992, Conca and Yang 1993, Gontard and Guilbert 1994). Protein films in particular have been discussed in detail by Gennadios et al (1994a) and …

Nutrient, Carbon, And Mass Loss During Composting Of Beef Cattle Feedlot Manure, Bahman Eghball, James F. Power, John E. Gilley, John W. Doran

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Quantification of nutrient and mass loss during composting is needed to understand the composting process, to implement methods for nutrient conservation, and to reduce potential adverse environmental impact. Beef cattle feedlot manure was composted in a windrow on an open concrete area in 1992, 1993, and 1994 to determine the amounts of nutrient, C, and mass loss during composting. The area was enclosed on all sides with a 0.2 m high metal sheet to direct runoff to a fiberglass tank (4000 L) during rainfall. Nutrients in runoff represented combined runoff and leaching losses. Nutrients, C, and mass loss during composting …

Runoff, Erosion, And Soil Quality Characteristics Of A Former Conservation Reserve Program Site, John E. Gilley, John W. Doran, Douglas Karlen, T. C. Kaspar

Department of Agricultural and Biological Systems Engineering: Faculty Publications

No-till and moldboard plow tillage systems were established on a former Conservation Reserve Program (CRP) site in southwest Iowa. Runoff rates from simulated rainfall events were significantly greater on sites returned to crop production than from adjoining, undisturbed CRP areas. Substantial soil loss was measured from the moldboard plow treatments, but no significant differences in erosion rates were found between the undisturbed CRP and no-till management systems. No-till management maintained levels of soil quality similar to those of CRP by preserving soil structural integrity and reducing losses of soil organic matter (SOM) associated with tillage. Conservation tillage systems which maintain …

Expression Of Human Protein C In Mammary Tissue Of Transgenic Mammals , William H. Velander

Department of Chemical and Biomolecular Engineering: Patents

Recombinant protein C characterized by a high percentage of active protein can be obtained in the milk of transgenic mammals that incorporate DNAs according to the present invention. Transgenic mammals of the present invention are produced by introducing into developing embryos DNA that encodes protein C, such that the DNA is stably incorporated in the DNA of germ line cells of the mature mammals and inherited in normal, mendelian fashion.

Trade-Off Study And Computer Simulation For Assessing Spacecraft Pointing Accuracy And Stability Capabilities, Marcelo C. Algrain, Richard M. Powers

Department of Electrical and Computer Engineering: Faculty Publications

A case study, written in a tutorial manner, is presented where a comprehensive computer simulation is developed to determine the driving factors contributing to spacecraft pointing accuracy and stability. Models for major system components are described. Among them are spacecraft bus, attitude controller, reaction wheel assembly, star-tracker unit, inertial reference unit, and gyro drift estimators (Kalman filter). The predicted spacecraft performance is analyzed for a variety of input commands and system disturbances. The primary deterministic inputs are the desired attitude angles and rate set points. The stochastic inputs include random torque disturbances acting on the spacecraft, random gyro bias noise, …

1995 Strategic Plan For Museum, Tractor Museum

Lester F. Larsen Tractor Museum: Planning and Development Documents

Roof Repair Contacting Tractor Manufacturers Inviting Donors to be Members

Tractor Test Museum Committee Minutes December 11, 1996, Tractor Museum

Lester F. Larsen Tractor Museum: Planning and Development Documents

Roof Repair Inviting Donors to be Members Treasurer's Report

Ellipsometer/Polarmeterbased Process Monitor And Control System Suitable For Simultaneous Retrofit On Molecular Beam Epitaxy System Rheed/Leed Interface System, And Method Of Use, John A. Woollam, Blaine D. Johs, Peter P. Chow

Department of Electrical and Computer Engineering: Faculty Publications

A method of, and system for applying light beam producing systems, such as ellipsometers, polarimeters, polarized light reflectance and functionally similar systems, such that a beam of light produced thereby is caused to be incident upon a process element at an angle in excess of an associated Brewster angle while enabling the production of a signal sufficiently sensitive to changes in process element parameters, for use in "real-time" process element process monitoring and control, is disclosed. In addition, a process element processing system and electron beam producing system and light beam producing system combination system is taught, wherein the electron …

Ellipsometer/Polarmeter Based Process Monitor And Control System Suitable For Simultaneous Retrofit On Molecular Beam Eptaxy System Rheed/Leed Interface System, And Method Of Use, John A. Woollam, Blaine D. Johs, Peter P. Chow

Department of Electrical and Computer Engineering: Faculty Publications

A method of, and system for, applying light beam producing systems such as ellipsometers, polarimeters, polarized light reflectance and functionally similar systems, such that a beam of light produced thereby is caused to be incident upon a process element at an angle in excess of an associated Brewster angle while enabling the production of a signal sufficiently sensitive to changes in process element parameters, for use in "real-time' process element process monitoring and control, is disclosed. In addition a process element processing system and electron beam producing system and light beam producing system combination system is taught, wherein the electronbeam …

Growth Of Diamond By Rf Plasma-Assisted Chemical Vapor Deposition, Duane E. Meyer, Natale J. Ianno, John A. Woollam, A. B. Swartzlander, A. J. Nelson

Department of Electrical and Computer Engineering: Faculty Publications

A system has been designed and constructed to produce diamond particles by inductively coupled radio-frequency, plasma-assisted chemical vapor deposition. This is a low-pressure, low-temperature process used in an attempt to deposit diamond on substrates of glass, quartz, silicon, nickel, and boron nitride. Several deposition parameters have been varied including substrate temperature, gas concentration, gas pressure, total gas flow rate, rf input power, and deposition time. Analytical methods employed to determine composition and structure of the deposits include scanning electron microscopy, absorption spectroscopy, scanning Auger microprobe spectroscopy, and Raman spectroscopy. Analysis indicates that particles having a thin graphite surface, as well …

Acuta Enews December 1996, Vol. 25, No. 12

ACUTA Newsletters

In This Issue

Fifth Annual Institutional Excellence Awards Competition

ACUTA News will have a new look

Welcome New Members

President's Message

Emergency Phone Provide Security

DC at a Glance

Fiber Optic Video Systems for Campus Networking

Campus News Briefs

Industry Insights

From ACUTA Headquarters

Diffuse Energy Propagation On Heterogeneous Plates: Structural Acoustics Radiative Transfer Theory, Joseph A. Turner, Richard L. Weaver

Department of Engineering Mechanics: Faculty Publications

The propagation of diffuse energy on an unwetted flat plate with attached heterogeneities is examined using a statistical, multiple scattering approach. The statistically homogeneous heterogeneities lightly couple the membrane and flexural waves. The problem is formulated in terms of the Bethe–Salpeter equation, which governs the field covariance. It is reduced to a radiative transfer equation in the limit that the attenuations per wave number are small, i.e., when the heterogeneities are weak. This radiative transfer equation governs the diffuse energy propagation as a function of space, time, and propagation direction. Solutions of the radiative transfer equation are presented for the …

Controlling Three-Axis Attitude Rates On A Pointing System Using Nonlinear Observer And Two Axis Measurements, Marcelo C. Algrain

Department of Electrical and Computer Engineering: Faculty Publications

A new observer design method that allows for estimating the angular rates along a vehicle’s three principal axes is described. The observer uses measurements from a single two-axis angular rate sensor (gyro) and determines the rates for the third axis using a nonlinear observer. Unlike conventional approaches where the equations governing vehicle motion (Euler’s equations) are linearized and then an observer is constructed based on the linear model, this method does not require linearization of the system. Instead, a pseudo-linear representation is used. The pseudo-linear model is obtained by systematically decomposing a nonlinear system into linear and nonlinear terms. The …

Application Of Inversions To Lossless Image Compression, Ziya Arnavut

Department of Electrical and Computer Engineering: Faculty Publications

Linear prediction schemes, such as that of the Joint Photographic Experts Group (JPEG), are simple and normally produces a residual sequence with lower zero-order entropy. Occasionally the entropy of the prediction error becomes greater than that of the original image. Such situations frequently occur when the image data have discrete gray levels located within certain intervals. To alleviate this problem, various authors have suggested different preprocessing methods. However, the techniques reported require two passes. We extend the definition of Lehmer-type inversions (Lehmer 1960 and 1964) from permutations to multiset permutations and present a one-pass algorithm based on inversions of a …

Acuta Enews November 1996, Vol. 25, No. 11

ACUTA Newsletters

In This Issue

Univ. of Idaho: Homepage Sweet Homepage

Institutional Excellence Award

Committee Member Approved

More Angles for 809 Fraud

Welcome New Members

President's Message

The '90s: New Challenges for Telecom

DC at a Glance

Campus News Briefs

Industry Insights

Oxygen Plasma Asher Contamination: An Analysis Of Sources And Remedies, R. A. Synowicki, Jeffrey S. Hale, William A. Mcgahan, Natale J. Ianno, John A. Woollam

Department of Electrical and Computer Engineering: Faculty Publications

The low Earth orbit (LEO) environment is commonly simulated using oxygen plasma ashers to determine the effects of LEO on spacecraft materials. However, plasma ashers can also contaminate samples during plasma exposure, making them less than ideal for space simulation. This study results from attempts to minimize or eliminate contamination. Optical methods of variable angle spectroscopic ellipsometry and reflectance spectrophotometry were used to quantify contaminant stoichiometry and deposition rate. Auger electron spectroscopy identified deposited contaminants and their surface coverage. Contamination results from etching of the rubber chamber seals by the plasma. The deposited contaminant was nearly indistinguishable from fully stoichiometric …

Acuta Enews October 1996, Vol. 25, No. 10

ACUTA Newsletters

In This Issue

President's Message

FlexSourcing

Desk Top Video

Overheard on the Listserve

From ACUTA Headquarters

A Continuous Process For The Conversion Of Vegetable Oils Into Biodiesel, Hossein Noureddini, D Harkey, V Medikonduru

Papers in Biomaterials

Over the last few years fatty acid methyl esters have assumed importance as research has intensified on the utilization of vegetable oils and animal fats derivatives from liquid fuels (better known as biodiesel).Traditional batch processing has been an still is the most widely used process for this coversion. New and more efficient processing schemes. for large scale production of biodiesel for fuelfile1 purposes, is a. key for commercialization of biodiesel. In this, study a continuous process for the transesterification of triglycerides to methyl esters was investigated. This process is based a combined high shear and motionless reactor system. The experimental …

Acuta Enews September 1996, Vol. 25, No. 9

ACUTA Newsletters

In This Issue

From the President

New Legislation

User Group Reports

Changes Come to Campus Directories

From ACUTA Headquarters

Affinity Purification Of Biologically Active Andinactive Forms Of Recombinant Human Protein C Produced In Porcine Mammary Gland, Kevin E. Van Cott, Barry Williams Department Of Chemical Engineering,Virginia Tech University, Blacksburg, Va 24061, Usa, William H. Velander, Francis C. Gwazdauskas, Tim Lee Jerome Holland Laboratory, American Red Cross, Rockville, Md 20855, Usa, Henryk Lubon, William N. Drohan

Papers in Biotechnology

Recombinant human protein C (rhPC) secreted in the milk of transgenic pigs was studied. 'Ikansgenes having different regulatory elements of the murine milk protein, whey acidic protein, were used with cDNA and genomic human protein C (hPC) DNA sequences to obtain lower and higher expressing animals. The cDNA pigs had a range of expression of about 0.1-0.5 g/l milk. Two different genomic hPC pig lines have expressed 0.3 and 1-2 g/l, respectively. The rhPC was first purified at yields greater than 60 per cent using a monoclonal antibody (mAb) to the activation site on the heavy chain of hPC. Subsequent …

Effect Of Antibody Orientation On Immunosorbent, Anuradha Subramanian, William H. Velander

Papers in Biotechnology

The impact of antibody orientation on immunosorbent efficiency was quantitatively assessed. A pH-dependent murine monoclonal antibody (Mab) against human protein C (hPC), recombinant hPC (rhPC) and two different immobilization chemistries and matrices were used as model systems. The lysyl groups of the rhPC were covalently modified with an acetic acid ester of N-hydroxysuccinimide and this modified rhPC was used as a Fab masking agent (FMA). The FMA was used to mask the antigen bind-ing regions (Fab) of the Mab prior to and during covalent immobilization. Thereafter, the residual active sites of the support were in-activated and the FMA was removed. …

Chemcial Vapor Deposition Precursor Chemistry. 5. The Photolytic Laser Deposition Of Aluminum Thin Films By Chemical Vapor Deposition, John A. Glass, Seong-Don Hwang, Saswati Datta, Brian W. Robertson, James T. Spencer

Department of Mechanical and Materials Engineering: Faculty Publications

Thin films of very high purity aluminum were formed from the laser photolysis of trimethylamine alane (TMAA) using both ultraviolet (pulsed nitrogen) and visible (argon ion) laser irradiation on a variety of substrates including gold. Si (111), GaAs (110) and Teflon (PTFE). At thicknesses of up to 1 μm, nearly linear growth rates of 377 Ås^-1 and 112 Ås^-1 were observed. The formation of volatile species formed during the deposition of aluminum from TMAA was investigated by quadrupole mass spectrometry (QMS) of the reactant gas stream. The highest intensity post-deposition mass fragments were observed at m/z 58, …

Fabrication Of Double Side Fully Metallized Plated Thru-Holes, In Polymer Structures, Without Seeding Or Photoprocess, Ravi F. Saraf

Department of Chemical and Biomolecular Engineering: Patents

The present invention is directed to a process of a method for the full metallization of thru-holes in a polymer structure comprising the steps of applying a film-forming amount of a conductive polymer-metal composite paste to a metal cathode; bonding a patterned polymer structure to said paste; subjecting said polymer structure to an electrolytic plating bath for a time sufficient to fully metallize thru-hole surfaces in said patterned polymer structure and removing the structure from the cathode assembly. The fully metallized thru-hole polymer structure can then be cleaned and polished to produce a finished product.

Proposal For Renovation Of 1920 Tractor Test Lab Into Museum, Tractor Museum

Lester F. Larsen Tractor Museum: Planning and Development Documents

Bids for Renovating Roof State Fair Display Further Funding for Renovation

Direct Chip Attachment (Dca) With Electrically Conductive Adhesives, Ravi F. Saraf

Department of Chemical and Biomolecular Engineering: Patents

A simple process for card assembly by Direct Chip Attachment (DCA) uses electrically conductive adhesives. Two methods create the same intermediate wafer product with a layer of insulative thermoplastic and conductive thermoplastic bumps. After sawing or dicing the wafer to form the chips, the chips are adhered to chip carriers with conductive pads which match the conductive thermoplastic bumps, using heat and pressure. Chips may be easily removed and replaced using heat.

Acuta Enews August 1996, Vol. 25, No. 8

ACUTA Newsletters

In This Issue

Silver Anniversary Celebration 25 Years of Excellence

President's Message

Chicago Presentations Inspire, Inform, and Entertain

Executive Director

DC at a Glance

Record Number of Exhibitors in Chicago

From ACUTA Headquarters

Sulfur Tolerant Bimetallic Zeolitic Reforming Catalysts, Gustavo F. Larsen

Department of Chemical and Biomolecular Engineering: Patents

New compositions of matter comprise a metal from the group consisting of platinum, rhodium and palladium, a metal from the first row of Group VIII of the Periodic Table and a nonacidic L-zeolite. A preferred composition is Pt--Ni/KL-zeolite. Such catalysts are prepared by coimpregnation of the zeolite with the metals. Methods of using the catalysts in reforming, aromatization or dehydrogenation are provided.

Monoclonal Antibody Assay And Kit For Detecting Metal Cations In Body Fluids, Randall R. Carlson, Jay S. Stout, Dwane E. Wylie, Fred W. Wagner, Malcolm Riddell

Biological Process Development Facility: Staff Publications

The invention provides method and kits for detecting a metallic cation in a sample of a body fluid. The preferred method and kits include the use of at least two different types of antibodies having different specificities. In the preferred method, the sample of body fluid can be contacted with an effective amount of a capture antibody specific for a naturally occurring polypeptide that can bind the metallic cation to form a first antigen-antibody complex. An effective amount of an antibody specific for an epitope on a metallic cation-naturally occurring polypeptide complex or an antibody specific for a metallic cation …