Engineering Commons^™

Fiber - Optic Temperature And Flow Sensor System And Methods, Ming Han, Guigen Liu, Weilin Hou

Department of Electrical and Computer Engineering: Faculty Publications

A fiber optic sensor, a process for utilizing a fiber optic sensor, and a process for fabricating a fiber optic sensor are described, where a double-side-polished silicon pillar is attached to an optical fiber tip and forms a Fabry-Perot cavity. In an implementation, a fiber optic sensor in accordance with an exemplary embodiment includes an optical fiber configured to be coupled to a light source and a spectrometer; and a single silicon layer or multiple silicon layers disposed on an end face of the optical fiber, where each of the silicon layer(s) defines a Fabry-Perot interferometer, and where the sensor …

Non-Vacuum Preparation Of Wse2 Thin Films Via The Selenization Of Hydrated Tungsten Oxide Prepared Using Chemical Solution Methods, Christopher L. Exstrom, Scott A. Darveau, Megan E. Falconer, Jessica R. Blum, Whitney M. Colling, Natale J. Ianno

Department of Electrical and Computer Engineering: Faculty Publications

It is known that tungsten oxide may be reacted with selenium sources to form WSe₂ but literature reports include processing steps that involve high temperatures, reducing atmospheres, and/or oxidative pre-treatments of tungsten oxide. In this work, we report a non-vacuum process for the fabrication of compositionally high quality WSe₂ thin films via the selenization of tungsten oxide under milder conditions. Tungsten source materials were various hydrated WO₃ and WO_2.9 compounds that were prepared using chemical solution techniques. Resulting films were selenized using a two-stage heating profile (250 °C for 15 minutes and 550 °C for 30 …

Non-Vacuum Preparation Of Wse2 Thin Films Via The Selenization Of Hydrated Tungsten Oxide Prepared Using Chemical Solution Methods, Christopher L. Exstrom, Scott A. Darveau, Megan E. Flaconer, Jessica R. Blum, Whitney M. Colling, Natale J. Ianno

Department of Electrical and Computer Engineering: Faculty Publications

It is known that tungsten oxide may be reacted with selenium sources to form WSe2 but literature reports include processing steps that involve high temperatures, reducing atmospheres, and/or oxidative pre-treatments of tungsten oxide. In this work, we report a non-vacuum process for the fabrication of compositionally high quality WSe2 thin films via the selenization of tungsten oxide under milder conditions. Tungsten source materials were various hydrated WO3 and WO2.9 compounds that were prepared using chemical solution techniques. Resulting films were selenized using a two-stage heating profile (250 oC for 15 minutes and 550 oC for 30 minutes) under a static …

Rapid And Damage-Free Outgassing Of Implanted Helium From Amorphous Silicon Oxycarbide, Qing Su, Hepeng Ding, Lloyd Price, Lin Shao, Jonathan A. Hinks, Graeme Greaves, Stephen E. Donnelly, Michael J. Demkowicz, Michael Nastasi

Nebraska Center for Energy Sciences Research: Publications

Damage caused by implanted helium (He) is a major concern for material performance in future nuclear reactors. We use a combination of experiments and modeling to demonstrate that amorphous silicon oxycarbide (SiOC) is immune to He-induced damage. By contrast with other solids, where implanted He becomes immobilized in nanometer-scale precipitates, He in SiOC remains in solution and outgasses from the material via atomic-scale diffusion without damaging its free surfaces. Furthermore, the behavior of He in SiOC is not sensitive to the exact concentration of carbon and hydrogen in this material, indicating that the composition of SiOC may be tuned to …

Visible Light Crosslinkable Human Hair Keratin Hydrogels, Kan Yue, Yanhui Liu, Batzaya Byambaa, Vaishali Singh, Wanjun Liu, Xiuyu Li, Yunxia Sun, Yu Shrike Zhang, Ali Tamayol, Peihua Zhang, Kee Woei Ng, Nasim Annabi, Ali Khademhosseini

Department of Mechanical and Materials Engineering: Faculty Publications

Keratins extracted from human hair have emerged as a promising biomaterial for various biomedical applications, partly due to their wide availability, low cost, minimal immune response, and the potential to engineer autologous tissue constructs. However, the fabrication of keratin-based scaffolds typically relies on limited crosslinking mechanisms, such as via physical interactions or disulfide bond formation, which are time-consuming and result in relatively poor mechanical strength and stability. Here, we report the preparation of photocrosslinkable keratin-polyethylene glycol (PEG) hydrogels via the thiol-norbornene “click” reaction, which can be formed within one minute upon irradiation of visible light. The resulting keratin-PEG hydrogels showed …

Title: Investigation Of Oxidative Reduction Reactions In Carbon-Based Electrocatalysts Presentation, Andrew Mason, Siamak Nejati, Shayan Kaviani

UCARE: Research Products

The expense of commonly used electrocatalysts such as Platinum and Palladium, make many battery technologies and electrochemical reactions cost-prohibitive. A new group of promising low-cost catalysts is doped carbon complexes. These materials need further development to reach the same activity as traditional catalysts. But by examining the Oxidative Reduction Reactions (ORR) of various carbon complexes, desirable characteristics and geometries can be identified and enhanced. For this comparative analysis, a series of Carbon Nanotube (CNT) and Graphene Complexes were tested.

Land Suitability Analysis For Emergency Medical Services Posts Along State Highways: A Case Study Of California, Ernest Tufuor, Laurence Rilett, Yunwoo Nam, Antonio Hurtado Beltran

Department of Civil and Environmental Engineering: Faculty Publications

The response time of Emergency Medical Services (EMS) to road accidents can be the difference between life and death. The California strategic highway safety plan highlight the need to improve the response time and recognizes that: 37% and 8% of the fatal crashes are 30 or more miles away from a trauma center in rural and urban areas respectively.

The paper seeks to: (1) demonstrate the viability of using spatial multi-criteria analysis in road safety management, and (2) provide a good scientific justification in selecting optimal counties for EMS posts. The goal is to propose areas that are close to …

Program And Proceedings: Nebraska Academy Of Sciences 1880–2018, 138th Anniversary Year, One Hundred-Twenty-Eighth Annual Meeting

Nebraska Academy of Sciences: Programs and Proceedings

Program

Aeronautics and Space Science

Collegiate Academy: Biology

Biological and Medical Sciences

Chemistry and Physics>/p>

Collegiate Academy: Chemistry and Physics

Learn to Print 3-D Models for Your Classroom Workshop

Aeronautics and Space Science Poster Session

Maiben Memorial Lecture: Thomas Clemente

Anthropology

Applied Science and Technology

Earth Science

Environmental Sciences

Teaching of Science and Mathematics

Friend of Science Award: Mary Kalen Romjue and Michael Sibbernsen

Cyber Security And Risk Society: Estonian Discourse On Cyber Risk And Security Strategy, Lauren Kook

Copyright, Fair Use, Scholarly Communication, etc.

The main aim of this thesis is to call for a new analysis of cyber security which departs from the traditional security theory. I argue that the cyber domain is inherently different in nature, in that it is lacking in traditional boundaries and is reflexive in nature. Policy-makers are aware of these characteristics, and in turn this awareness changes the way that national cyber security strategy is handled and understood. These changes cannot be adequately understood through traditional understanding of security, as they often are, without missing significant details. Rather, examining these changes through the lens of Ulrich Beck’s risk …

Using Virtual Reality And Photogrammetry To Enrich 3d Object Identity, Cole Juckette, Heather Richards-Rissetto, Hector Eluid Guerra Aldana, Norman Martinez

Department of Anthropology: Faculty Publications

The creation of digital 3D models for cultural heritage is commonplace. With the advent of efficient and cost effective technologies archaeologists are making a plethora of digital assets. This paper evaluates the identity of 3D digital assets and explores how to enhance or expand that identity by integrating photogrammetric models into VR. We propose that when a digital object acquires spatial context from its virtual surroundings, it gains an identity in relation to that virtual space, the same way that embedding the object with metadata gives it a specific identity through its relationship to other information. We explore this concept …

Comparison Of Three Regionalization Techniques For Predicting Streamflow In Ungaged Watersheds In Nebraska, Usa Using Swat Model, Michael W. Van Liew, Aaron R. Mittelstet

Department of Agricultural and Biological Systems Engineering: Faculty Publications

This study compared three approaches, regional averaging, nearest neighbor, and donor techniques, to regionalize parameters in the Soil and Water Assessment Tool (SWAT) on eleven watersheds located in the Dissected Plains, Plains, and Rolling Hills Landforms in the eastern portion of the State of Nebraska, USA. Within the Rolling Hills Landform, three watersheds were randomly selected as calibration watersheds while two were randomly selected as validation watersheds. Two watersheds were randomly selected as calibration watersheds while one was randomly selected as a validation watershed within each of the Dissected Plains and Plains Landforms. The seven calibration watersheds were used to …

Methods, Systems, And Devices Relating To Force Control Surgical Systems, Shane M. Farritor, Thomas Frederick, Kearney Lackas, Joe Bartels, Jacob Greenburg

Department of Mechanical and Materials Engineering: Faculty Publications

The various embodiments herein relate to robotic surgical systems and devices that use force and/or torque sensors to measure forces applied at various components of the system or device. Certain implementations include robotic surgical devices having one or more force/torque sensors that detect or measure one or more forces applied at or on one or more arms. Other embodiments relate to systems having a robotic surgical device that has one or more sensors and an external controller that has one or more motors such that the sensors transmit information that is used at the controller to actuate the motors to …

Frequency Dependent Deformation Reversibility During Cyclic Loading, Shuai Shao, Michael M. Khonsari, Jian Wang, Nima Shamsaei, Nan Li

Department of Mechanical and Materials Engineering: Faculty Publications

High-frequency testing (HFT) is useful for accelerated fatigue testing of conventional materials that typically serve under low-frequency loading conditions, as well as for the assessment of the robustness of microelectromechanical systems which typically experience high-frequency service conditions. Using discrete dislocation dynamics, we attempt to elucidate the effect of loading frequency on the reversibility of cyclic deformation. We demonstrate that the HFT induces a higher fraction of reversible cyclic deformation because of a larger portion of elastic/anelastic deformation due to limited dislocation mobility, and a higher degree of reversibility in plastic deformation owing to the less occurrence of cross-slip.

Investigation Of Toppling Ball Flight In American Football With A Mechanical Field-Goal Kicker, Chase M Pfeifer, Timothy J. Gay, Jeff A. Hawks, Shane Farritor, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

A mechanical field-goal kicking machine was used to investigate toppling ball flight in American football place-kicking, eliminating a number of uncontrollable impact variables present with a human kicker. Ball flight trajectories were recorded using a triangulation-based projectile tracking system to account for the football’s 3-dimensional position during flight as well as initial launch conditions. The football flights were described using kinematic equations relating to projectile motion including stagnant air drag and were compared to measured trajectories as well as projectile motion equations that exclude stagnant air drag. Measured football flight range deviations from the non-drag equations of projectile motion corresponded …

Test 2206: Challenger Mt740, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2204: John Deere 5090m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2201: John Deere 6195r Autoquad-Plus, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2199a: New Holland Workmaster 60, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2203: John Deere 9420rx, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2198: John Deere 5125r Pfc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2195: John Deere 5115r Oc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2199: Case Ih Farmall 60a, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2193: John Deere 5100r Oc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2191: John Deere 5090r Oc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2197: John Deere 5125r Oc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2196: John Deere 5115r Pfc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2192: John Deere 5090r Pfc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2194: John Deere 5100r Pfc, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1158 John Deere 6230r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

An Integrated Microstructural-Nanomechanical-Chemical Approach To Examine Material-Specific Characteristics Of Cementitious Interphase Regions, Mahdieh Khedmati, Yong-Rak Kim, Joesph A. Turner, Hani Alanazi, Charles Nguyen

Department of Mechanical and Materials Engineering: Faculty Publications

Effective properties and structural performance of cementitious mixtures are substantially governed by the quality of the interphase region because it acts as a bridge transferring forces between aggregates and a binding matrix and is generally susceptible to damage. As alternative binding agents like alkali-activated precursors have obtained substantial attention in recent years, there is a growing need for fundamental knowledge to uncover interphase formation mechanisms. In this paper, two different types of binding materials, i.e., fly ash-based geopolymer and ordinary portland cement, were mixed with limestone aggregate to examine and compare the microstructures and nanomechanical properties of interphase region. To …