Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

University of Kentucky

Discipline
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 2161 - 2190 of 6346

Full-Text Articles in Engineering

Fault Identification And Location For Distribution Network With Distributed Generations, Wen Fan, Yuan Liao May 2018

Fault Identification And Location For Distribution Network With Distributed Generations, Wen Fan, Yuan Liao

Electrical and Computer Engineering Faculty Publications

Power distribution networks with distributed generations may experience faults. It is essential to promptly locate the fault for fast repair and restoration. This paper presents a novel method for identifying the faulted section and accurate location of faults that occur on power distribution grid. Appropriate matrices are set up to represent meter locations on the grid and the topology of the grid. The voltage and current measurements obtained are utilized to decide the fault sections. Then fault location is determined by solving equations that link measurements and fault locations through bus impedance matrix. The method is applicable to both single …

Go to article

Performance Evaluation Of Energy-Autonomous Sensors Using Power-Harvesting Beacons For Environmental Monitoring In Internet Of Things (Iot), George Dan Moiş, Teodora Sanislav, Silviu Corneliu Folea, Sherali Zeadally May 2018

Performance Evaluation Of Energy-Autonomous Sensors Using Power-Harvesting Beacons For Environmental Monitoring In Internet Of Things (Iot), George Dan Moiş, Teodora Sanislav, Silviu Corneliu Folea, Sherali Zeadally

Information Science Faculty Publications

Environmental conditions and air quality monitoring have become crucial today due to the undeniable changes of the climate and accelerated urbanization. To efficiently monitor environmental parameters such as temperature, humidity, and the levels of pollutants, such as fine particulate matter (PM2.5) and volatile organic compounds (VOCs) in the air, and to collect data covering vast geographical areas, the development of cheap energy-autonomous sensors for large scale deployment and fine-grained data acquisition is required. Rapid advances in electronics and communication technologies along with the emergence of paradigms such as Cyber-Physical Systems (CPSs) and the Internet of Things (IoT) have led to …

Go to article

Nanoparticle-Mediated Therapeutic Agent Delivery For Treating Metastatic Breast Cancer—Challenges And Opportunities, Yunfei Li, Brock Humphries, Chengfeng Yang, Zhishan Wang May 2018

Nanoparticle-Mediated Therapeutic Agent Delivery For Treating Metastatic Breast Cancer—Challenges And Opportunities, Yunfei Li, Brock Humphries, Chengfeng Yang, Zhishan Wang

Toxicology and Cancer Biology Faculty Publications

Breast cancer (BC) is the second leading cause of cancer-related death in American women and more than 90% of BC-related death is caused by metastatic BC (MBC). This review stresses the limited success of traditional therapies as well as the use of nanomedicine for treating MBC. Understanding the biological barriers of MBC that nanoparticle in vivo trafficking must overcome could provide valuable new insights for translating nanomedicine from the bench side to the bedside. A view about nanomedicine applied in BC therapy has been summarized with their present status, which is gaining attention in the clinically-applied landscape. The progressions of …

Go to article

A Low-Cost Method For Collecting Hyperspectral Measurements From A Small Unmanned Aircraft System, Ali Hamidisepehr, Michael P. Sama May 2018

A Low-Cost Method For Collecting Hyperspectral Measurements From A Small Unmanned Aircraft System, Ali Hamidisepehr, Michael P. Sama

Biosystems and Agricultural Engineering Faculty Publications

Small unmanned aircraft systems (UAS) are a relatively new tool for collecting remote sensing data at dense spatial and temporal resolutions. This study aimed to develop a spectral measurement platform for deployment on a UAS for quantifying and delineating moisture zones within an agricultural landscape. A series of portable spectrometers covering ultraviolet (UV), visible (VIS), and near-infrared (NIR) wavelengths were instrumented using a Raspberry Pi embedded computer that was programmed to interface with the UAS autopilot for autonomous data acquisition. A second set of identical spectrometers were fitted with calibrated irradiance lenses to capture ambient light during data acquisition. Data …

Go to article

Investigation Of The Use Of A Bio-Derived Solvent For Non-Solvent-Induced Phase Separation (Nips) Fabrication Of Polysulfone Membranes, Xiaobo Dong, Amna Al-Jumaily, Isabel Escobar May 2018

Investigation Of The Use Of A Bio-Derived Solvent For Non-Solvent-Induced Phase Separation (Nips) Fabrication Of Polysulfone Membranes, Xiaobo Dong, Amna Al-Jumaily, Isabel Escobar

Chemical and Materials Engineering Faculty Publications

Organic solvents, such as N-methyl-2-pyrrolidone (NMP) and dimethylacetamide (DMAc), have been traditionally used to fabricate polymeric membranes. These solvents may have a negative impact on the environment and human health; therefore, using renewable solvents derived from biomass is of great interest to make membrane fabrication sustainable. Methyl-5-(dimethylamino)-2-methyl-5-oxopentanoate (Rhodiasolv PolarClean) is a bio-derived, biodegradable, nonflammable and nonvolatile solvent. Polysulfone is a commonly used polymer to fabricate membranes due to its thermal stability, strong mechanical strength and good chemical resistance. From cloud point curves, PolarClean showed potential to be a solvent for polysulfone. Membranes prepared with PolarClean were investigated in terms of …

Go to article

Research And Development Of Powder Brazing Filler Metals For Diamond Tools: A Review, Fei Long, Peng He, Dusan P. Sekulic May 2018

Research And Development Of Powder Brazing Filler Metals For Diamond Tools: A Review, Fei Long, Peng He, Dusan P. Sekulic

Mechanical Engineering Faculty Publications

Powder brazing filler metals (PBFMs) feature a number of comparative advantages. Among others, these include a low energy consumption, an accurate dosage, a good brazeability, a short production time, and a high production efficiency. These filler metals have been used in the aerospace, automobile, and electric appliances industries. The PBFMs are especially suitable for diamond tools bonding, which involves complex workpiece shapes and requires accurate dosage. The recent research of PBFMs for diamond tools is reviewed in this paper. The current applications are discussed. The CuSnTi and Ni-Cr-based PBFMs have been the two commonly used monolayer PBFMs. Thus, the bonding …

Go to article

Study Of Near-Cup Droplet Breakup Of An Automative Electrostatic Rotary Bell (Esrb) Atomizer Using High-Speed Shadowgraph Imaging, Jacob E. Wilson, Stephen William Grib, Adnan Darwish Ahmad, Michael W. Renfro, Scott A. Adams, Ahmad Salaimeh May 2018

Study Of Near-Cup Droplet Breakup Of An Automative Electrostatic Rotary Bell (Esrb) Atomizer Using High-Speed Shadowgraph Imaging, Jacob E. Wilson, Stephen William Grib, Adnan Darwish Ahmad, Michael W. Renfro, Scott A. Adams, Ahmad Salaimeh

Mechanical Engineering Faculty Publications

Electrostatic Rotary bell (ESRB) atomizers are used as the dominant means of paint application by the automotive industry. They utilize the high rotational speed of a cup to induce primary atomization of a liquid along with shaping air to provide secondary atomization and transport. In order to better understand the fluid breakup mechanisms involved in this process, high-speed shadowgraph imaging was used to visualize the edge of a serrated rotary bell at speeds varying between 5000 and 12,000 RPM and with a water flow rate of 250 ccm. A multi-step image processing algorithm was developed to differentiate between ligaments and …

Go to article

Analysis Of Surface Integrity In Machining Of Aisi 304 Stainless Steel Under Various Cooling And Cutting Conditions, F. Klocke, B. Döbbeler, S. Lung, S. Seelbach, Ibrahim S. Jawahir May 2018

Analysis Of Surface Integrity In Machining Of Aisi 304 Stainless Steel Under Various Cooling And Cutting Conditions, F. Klocke, B. Döbbeler, S. Lung, S. Seelbach, Ibrahim S. Jawahir

Institute for Sustainable Manufacturing Faculty Publications

Recent studies have shown that machining under specific cooling and cutting conditions can be used to induce a nanocrystalline surface layer in the workspiece. This layer has beneficial properties, such as improved fatigue strength, wear resistance and tribological behavior. In machining, a promising approach for achieving grain refinement in the surface layer is the application of cryogenic cooling. The aim is to use the last step of the machining operation to induce the desired surface quality to save time-consuming and expensive post machining surface treatments. The material used in this study was AISI 304 stainless steel. This austenitic steel suffers …

Go to article

Method Of Increasing Mass Transfer Rate Of Acid Gas Scrubbing Solvents, Cameron Anthony Lippert, Kunlei Liu, Christine Marie Brandewie, Joseph Eugene Remias, Moushumi Sarma May 2018

Method Of Increasing Mass Transfer Rate Of Acid Gas Scrubbing Solvents, Cameron Anthony Lippert, Kunlei Liu, Christine Marie Brandewie, Joseph Eugene Remias, Moushumi Sarma

Center for Applied Energy Research Faculty Patents

A method and catalysts for increasing the overall mass transfer rate of acid gas scrubbing solids is disclosed. Various catalyst compounds for that purpose are also disclosed.

Go to article

Impact Of Seasonal Tree-Cutting Restrictions On Construction Bids, Christopher W. Van Dyke, Steven Waddle, Bryan Gibson, Sarah M. Mccormack, Steven Douglas Kreis May 2018

Impact Of Seasonal Tree-Cutting Restrictions On Construction Bids, Christopher W. Van Dyke, Steven Waddle, Bryan Gibson, Sarah M. Mccormack, Steven Douglas Kreis

Kentucky Transportation Center Research Report

Many of the maintenance and construction projects undertaken by the Kentucky Transportation Cabinet (KYTC) span late spring to early fall (April–October), with this period’s long days, abundant sunshine, and relatively dry conditions being ideal for performing work and minimizing delays from inclement weather. But this compressed timeline for accomplishing work introduces other challenges. Specifically, many of KYTC’s maintenance and construction activities can potentially impact summer habitat of the Indiana bat, which is listed as an endangered species. Removing trees classified as Indiana bat habitat is allowed, however, to do so the Cabinet is required to pay a mitigation fee. The …

Go to article

Transportation System Vulnerability And Resilience To Extreme Weather Events And Other Natural Hazards — Final Results Of Vulnerability Assessment Of National Highway System For All Kytc Districts, Benjamin L. Blandford, Scott Schurman, Candice Y. Wallace May 2018

Transportation System Vulnerability And Resilience To Extreme Weather Events And Other Natural Hazards — Final Results Of Vulnerability Assessment Of National Highway System For All Kytc Districts, Benjamin L. Blandford, Scott Schurman, Candice Y. Wallace

Kentucky Transportation Center Research Report

Recent federal legislation and the Federal Highway Administration (FHWA) have directed state transportation agencies to identify potential vulnerabilities associated with extreme weather events and climate change, develop a risk-based asset management plan, and incorporate findings into transportation planning, design, and maintenance practices. The Kentucky Transportation Center and Kentucky Transportation Cabinet developed and led district-level workshops to elicit local expert knowledge on asset vulnerabilities to natural hazards. Combining the results of these workshops with analysis of available data on assets and hazards, they then performed a natural hazard vulnerability assessment of the state’s National Highway System (NHS) for each of Kentucky’s …

Go to article

Advancing The Understanding Of Environmental Transformations, Bioavailability And Effects Of Nanomaterials, An International Us Environmental Protection Agency—Uk Environmental Nanoscience Initiative Joint Program, Mitch M. Lasat, Kian Fan Chung, Jamie Lead, Steve Mcgrath, Richard J. Owen, Sophie Rocks, Jason M. Unrine, Junfeng Zhang Apr 2018

Advancing The Understanding Of Environmental Transformations, Bioavailability And Effects Of Nanomaterials, An International Us Environmental Protection Agency—Uk Environmental Nanoscience Initiative Joint Program, Mitch M. Lasat, Kian Fan Chung, Jamie Lead, Steve Mcgrath, Richard J. Owen, Sophie Rocks, Jason M. Unrine, Junfeng Zhang

Plant and Soil Sciences Faculty Publications

Nanotechnology has significant economic, health, and environmental benefits, including renewable energy and innovative environmental solutions. Manufactured nanoparticles have been incorporated into new materials and products because of their novel or enhanced properties. These very same properties also have prompted concerns about the potential environmental and human health hazard and risk posed by the manufactured nanomaterials. Appropriate risk management responses require the development of models capable of predicting the environmental and human health effects of the nanomaterials. Development of predictive models has been hampered by a lack of information concerning the environmental fate, behavior and effects of manufactured nanoparticles. The United …

Go to article

Optimizing The Use Of A Liquid Handling Robot To Conduct A High Throughput Forward Chemical Genetics Screen Of Arabidopsis Thaliana, B. Kirtley Amos, Victoria G. Pook, Seth Debolt Apr 2018

Optimizing The Use Of A Liquid Handling Robot To Conduct A High Throughput Forward Chemical Genetics Screen Of Arabidopsis Thaliana, B. Kirtley Amos, Victoria G. Pook, Seth Debolt

Horticulture Faculty Publications

Chemical genetics is increasingly being employed to decode traits in plants that may be recalcitrant to traditional genetics due to gene redundancy or lethality. However, the probability of a synthetic small molecule being bioactive is low; therefore, thousands of molecules must be tested in order to find those of interest. Liquid handling robotics systems are designed to handle large numbers of samples, increasing the speed with which a chemical library can be screened in addition to minimizing/standardizing error. To achieve a high-throughput forward chemical genetics screen of a library of 50,000 small molecules on Arabidopsis thaliana (Arabidopsis), protocols using a …

Go to article

Method For Production Of Germanium Nanowires Encapsulated Within Multi-Walled Carbon Nanotubes, Mark Crocker, Rodney Andrews, Arumugam Pandurangan, Dali Qian Apr 2018

Method For Production Of Germanium Nanowires Encapsulated Within Multi-Walled Carbon Nanotubes, Mark Crocker, Rodney Andrews, Arumugam Pandurangan, Dali Qian

Center for Applied Energy Research Faculty Patents

A method is provided for producing germanium nanowires encapsulated within multi-walled carbon nanotubes. The method includes the steps of performing chemical vapor deposition using a combined germanium and carbon source having a general formula of GeR(4-x)Lx, where x=0, 1, 2, or 3; R is selected from a group consisting of alkyl, cycloalkyl or aryl and L=hydrogen, halide or alkoxide and growing germanium nanowires encapsulated within multi-walled carbon nanotubes on a substrate. A reaction product of that method or process is also provided.

Go to article

Evaluation Of A Novel Finite Element Model Of Active Contraction In The Heart, Xiaoyan Zhang, Zhan-Qiu Liu, Kenneth S. Campbell, Jonathan F. Wenk Apr 2018

Evaluation Of A Novel Finite Element Model Of Active Contraction In The Heart, Xiaoyan Zhang, Zhan-Qiu Liu, Kenneth S. Campbell, Jonathan F. Wenk

Mechanical Engineering Faculty Publications

Finite element (FE) modeling is becoming a widely used approach for the investigation of global heart function. In the present study, a novel model of cellular-level systolic contraction, which includes both length- and velocity-dependence, was implemented into a 3D non-linear FE code. To validate this new FE implementation, an optimization procedure was used to determine the contractile parameters, associated with sarcomeric function, by comparing FE-predicted pressure and strain to experimental measures collected with magnetic resonance imaging and catheterization in the ventricles of five healthy rats. The pressure-volume relationship generated by the FE models matched well with the experimental data. Additionally, …

Go to article

Multienzyme Immobilized Polymeric Membrane Reactor For The Transformation Of A Lignin Model Compound, Rupam Sarma, Md. Saiful Islam, Mark P. Running, Dibakar Bhattacharyya Apr 2018

Multienzyme Immobilized Polymeric Membrane Reactor For The Transformation Of A Lignin Model Compound, Rupam Sarma, Md. Saiful Islam, Mark P. Running, Dibakar Bhattacharyya

Chemical and Materials Engineering Faculty Publications

We have developed an integrated, multienzyme functionalized membrane reactor for bioconversion of a lignin model compound involving enzymatic catalysis. The membrane bioreactors were fabricated through the layer-by-layer assembly approach to immobilize three different enzymes (glucose oxidase, peroxidase and laccase) into pH-responsive membranes. This novel membrane reactor couples the in situ generation of hydrogen peroxide (by glucose oxidase) to oxidative conversion of a lignin model compound, guaiacylglycerol-β-guaiacyl ether (GGE). Preliminary investigation of the efficacy of these functional membranes towards GGE degradation is demonstrated under convective flow mode. Over 90% of the initial feed could be degraded with the multienzyme immobilized membranes …

Go to article

Effective Room-Temperature Ammonia-Sensitive Composite Sensor Based On Graphene Nanoplates And Pani, Zongbiao Ye, Yan Chen, Bohao Liu, Yuanjie Su, Zhi Chen, Huiling Tai, Yadong Jiang Apr 2018

Effective Room-Temperature Ammonia-Sensitive Composite Sensor Based On Graphene Nanoplates And Pani, Zongbiao Ye, Yan Chen, Bohao Liu, Yuanjie Su, Zhi Chen, Huiling Tai, Yadong Jiang

Electrical and Computer Engineering Faculty Publications

The graphene nanoplate (GN)-polyaniline (PANI) composite was developed via in-situ polymerization method and simultaneously assembled on interdigital electrodes (IDEs) at low temperature for ammonia (NH3) detection. The assembled composite sensor showed excellent sensing performance toward different concentrations of NH3, 1.5 of response value and 123 s/204 s for the response/recovery time to 15 ppm NH3. Meanwhile, an interesting supersaturation phenomenon was observed at high concentration of NH3. A reasonable speculation was proposed for this special sensing behavior and the mechanism for enhanced sensing properties was also analyzed.

Go to article

Renal Granulomatosis Post Intravesical Bacillus Calmette-Guerin Therapy For Non-Muscle-Invasive Bladder Cancer, Karen Tran-Harding, Rashmi T. Nair, Halemane S. Ganesh Apr 2018

Renal Granulomatosis Post Intravesical Bacillus Calmette-Guerin Therapy For Non-Muscle-Invasive Bladder Cancer, Karen Tran-Harding, Rashmi T. Nair, Halemane S. Ganesh

Radiology Faculty Publications

Intravesical Bacillus Calmette–Guerin (BCG) immunotherapy is a proven, effective treatment for intermediate- and high-risk non-muscle-invasive bladder cancer. Minor side effects are common and expected but systemic effects can occur in < 5% of treated patients. We present a rare case of a 49-year-old male that presented with fever and chills after 3 weeks of intravesical BCG therapy post transurethral resection of bladder tumor. New renal lesions were present on contrast-enhanced computed tomography scan which was histologically proven to be necrotizing renal granulomatosis.

Go to article

Sensor Technologies For Intelligent Transportation Systems, Juan Guerrero-Ibáñez, Sherali Zeadally, Juan Contreras-Castillo Apr 2018

Sensor Technologies For Intelligent Transportation Systems, Juan Guerrero-Ibáñez, Sherali Zeadally, Juan Contreras-Castillo

Information Science Faculty Publications

Modern society faces serious problems with transportation systems, including but not limited to traffic congestion, safety, and pollution. Information communication technologies have gained increasing attention and importance in modern transportation systems. Automotive manufacturers are developing in-vehicle sensors and their applications in different areas including safety, traffic management, and infotainment. Government institutions are implementing roadside infrastructures such as cameras and sensors to collect data about environmental and traffic conditions. By seamlessly integrating vehicles and sensing devices, their sensing and communication capabilities can be leveraged to achieve smart and intelligent transportation systems. We discuss how sensor technology can be integrated with the …

Go to article

Scalable Patterning Using Laser-Induced Shock Waves, Saidjafarzoda Ilhom, Khomidkhodza Kholikov, Peizhen Li, Claire Ottman, Dylan Sanford, Zachary Thomas, Omer San, Haluk E. Karaca, Ali O. Er Apr 2018

Scalable Patterning Using Laser-Induced Shock Waves, Saidjafarzoda Ilhom, Khomidkhodza Kholikov, Peizhen Li, Claire Ottman, Dylan Sanford, Zachary Thomas, Omer San, Haluk E. Karaca, Ali O. Er

Mechanical Engineering Faculty Publications

An advanced direct imprinting method with low cost, quick, and minimal environmental impact to create a thermally controllable surface pattern using the laser pulses is reported. Patterned microindents were generated on Ni50Ti50 shape memory alloys and aluminum using an Nd: YAG laser operating at 1064 nm combined with a suitable transparent overlay, a sacrificial layer of graphite, and copper grid. Laser pulses at different energy densities, which generate pressure pulses up to a few GPa on the surface, were focused through the confinement medium, ablating the copper grid to create plasma and transferring the grid pattern onto …

Go to article

Developing Knowledge Management Strategies, Bryan Gibson, Candice Y. Wallace, Steven Douglas Kreis Apr 2018

Developing Knowledge Management Strategies, Bryan Gibson, Candice Y. Wallace, Steven Douglas Kreis

Kentucky Transportation Center Research Report

Retirements and other staff changes have led to a loss of institutional knowledge across public agencies. These changing workforce dynamics have highlighted the study of knowledge management, and how organizations can best retain their core knowledge bases. Key to understanding knowledge management is how organizations have approached the issue and the most effective methods and processes they have used to retain, store, and disseminate knowledge. Part of the knowledge management discussion includes core competencies, or what basic knowledge and skills are essential to an organization’s mission. Also, considering the impacts of outsourcing on public employment, is another key to understanding …

Go to article

Redefining Commercial Vehicle Permitting And Credentialing Violations, Andrew Martin, Jennifer R. Walton, Valerie J. Keathley Apr 2018

Redefining Commercial Vehicle Permitting And Credentialing Violations, Andrew Martin, Jennifer R. Walton, Valerie J. Keathley

Kentucky Transportation Center Research Report

The objective of this study was to analyze enforcement and adjudication of common commercial vehicle tax, credentialing, and safety offenses. This study examined violations of the International Fuel Tax Agreement and the Kentucky Intrastate Tax, Kentucky’s weight distance tax, Unified Carrier Registration, Kentucky size and weight laws, and federal safety regulations from 2004 to 2013. Statistical analysis showed declining conviction rates, increasing dismissal rates, and a drop in collections of court costs and fines associated with these offenses. In addition, adjudication varied significantly from district court to district court, which is creating an equity issue for motor carriers and the …

Go to article

Longer Lasting Bridge Deck Overlays, David Q. Hunsucker, Kean H. Ashurst Jr., Brad W. Rister, David L. Allen, Eileen Grady Apr 2018

Longer Lasting Bridge Deck Overlays, David Q. Hunsucker, Kean H. Ashurst Jr., Brad W. Rister, David L. Allen, Eileen Grady

Kentucky Transportation Center Research Report

The objective of this report is to determine the most effective method for bridge deck overlay construction and repair by assessing current practices; examining new products and technologies; and reviewing NCHRP (National Cooperative Highway Research Program) guidelines, state standard specifications, ASCE (American Society of Civil Engineers) infrastructure ratings, and original bridge core chloride penetration data. Based on the review, this report offers the following conclusions. Latex modified concrete (LMC) overlays perform well, provide a long service life, and are the most commonly used method of bridge deck rehabilitation. Ohio considers microsilica concrete (MSC) overlays as state of the art due …

Go to article

Modeling And Validation Of Local Electrowinning Electrode Current Density Using Two Phase Flow And Nernst-Planck Equations, Joshua M. Werner, W. Zeng, M. L. Free, Z. Zhang, J. Cho Mar 2018

Modeling And Validation Of Local Electrowinning Electrode Current Density Using Two Phase Flow And Nernst-Planck Equations, Joshua M. Werner, W. Zeng, M. L. Free, Z. Zhang, J. Cho

Mining Engineering Faculty Publications

In this work we demonstrate the validity of a multi-physics model using COMSOL to predict the local current density distribution at the cathode of a copper electrowinning test cell. Important developments utilizing Euler-Euler bubbly flow with coupled Nernst-Planck transport equations allow additional insights into deposit characteristics and topographies.

Go to article

Modeling Of Nitihf Using Finite Difference Method, Nazanin Farjam, Reza Mehrabi, Haluk E. Karaca, Reza Mirzaeifar, Mohammad Elahinia Mar 2018

Modeling Of Nitihf Using Finite Difference Method, Nazanin Farjam, Reza Mehrabi, Haluk E. Karaca, Reza Mirzaeifar, Mohammad Elahinia

Mechanical Engineering Faculty Publications

NiTiHf is a high temperature and high strength shape memory alloy with transformation temperatures above 100oC. A constitutive model based on Gibbs free energy is developed to predict the behavior of this material. Two different irrecoverable strains including transformation induced plastic strain (TRIP) and viscoplastic strain (VP) are considered when using high temperature shape memory alloys (HTSMAs). The first one happens during transformation at high levels of stress and the second one is related to the creep which is rate-dependent. The developed model is implemented for NiTiHf under uniaxial loading. Finite difference method is utilized to solve the proposed equations. …

Go to article

Selective Laser Melting Of Ni-Rich Niti: Selection Of Process Parameters And The Superelastic Response, Narges Shayesteh Moghaddam, Soheil Saedi, Amirhesam Amerinatanzi, Ehsan Saghaian, Ahmadreza Jahadakbar, Haluk E. Karaca, Mohammad Elahinia Mar 2018

Selective Laser Melting Of Ni-Rich Niti: Selection Of Process Parameters And The Superelastic Response, Narges Shayesteh Moghaddam, Soheil Saedi, Amirhesam Amerinatanzi, Ehsan Saghaian, Ahmadreza Jahadakbar, Haluk E. Karaca, Mohammad Elahinia

Mechanical Engineering Faculty Publications

Material and mechanical properties of NiTi shape memory alloys strongly depend on the fabrication process parameters and the resulting microstructure. In selective laser melting, the combination of parameters such as laser power, scanning speed, and hatch spacing determine the microstructural defects, grain size and texture. Therefore, processing parameters can be adjusted to tailor the microstructure and mechanical response of the alloy. In this work, NiTi samples were fabricated using Ni50.8Ti (at.%) powder via SLM PXM by Phenix/3D Systems and the effects of processing parameters were systematically studied. The relationship between the processing parameters and superelastic properties were investigated …

Go to article

Influence Of Slm On Compressive Response Of Niti Scaffolds, Narges Shayesteh Moghaddam, Soheil Saedi, Amirhesam Amerinatanzi, Ahmadreza Jahadakbar, Sayed Ehsan Saghaian, Haluk E. Karaca, Mohammad Elahinia Mar 2018

Influence Of Slm On Compressive Response Of Niti Scaffolds, Narges Shayesteh Moghaddam, Soheil Saedi, Amirhesam Amerinatanzi, Ahmadreza Jahadakbar, Sayed Ehsan Saghaian, Haluk E. Karaca, Mohammad Elahinia

Mechanical Engineering Faculty Publications

Porous Nickel-Titanium shape memory alloys (NiTi-SMAs) have attracted much attention in biomedical applications due to their high range of pure elastic deformability (i.e., superelasticity) as well as their bone-level modulus of elasticity (E≈12-20 GPa). In recent years, Selective Laser Melting (SLM) has been used to produce complex NiTi components. The focus of this study is to investigate the superelasticity and compressive properties of SLM NiTi-SMAs. To this aim, several NiTi components with different level of porosities (32- 58%) were fabricated from Ni50.8Ti (at. %) powder via SLM PXM by Phenix/3D Systems, using optimum processing parameter (Laser power-P=250 W, …

Go to article

A Model-Based Approach For Estimation Of Changes In Lumbar Segmental Kinematics Associated With Alterations In Trunk Muscle Forces, Iman Shojaei, Navid Arjmand, Judith R. Meakin, Babak Bazrgari Mar 2018

A Model-Based Approach For Estimation Of Changes In Lumbar Segmental Kinematics Associated With Alterations In Trunk Muscle Forces, Iman Shojaei, Navid Arjmand, Judith R. Meakin, Babak Bazrgari

Biomedical Engineering Faculty Publications

The kinematics information from imaging, if combined with optimization-based biomechanical models, may provide a unique platform for personalized assessment of trunk muscle forces (TMFs). Such a method, however, is feasible only if differences in lumbar spine kinematics due to differences in TMFs can be captured by the current imaging techniques. A finite element model of the spine within an optimization procedure was used to estimate segmental kinematics of lumbar spine associated with five different sets of TMFs. Each set of TMFs was associated with a hypothetical trunk neuromuscular strategy that optimized one aspect of lower back biomechanics. For each set …

Go to article

Walking Speed Differentially Alters Spinal Loads In Persons With Traumatic Lower Limb Amputation, Brad D. Hendershot, Iman Shojaei, Julian C. Acasio, Christopher L. Dearth, Babak Bazrgari Mar 2018

Walking Speed Differentially Alters Spinal Loads In Persons With Traumatic Lower Limb Amputation, Brad D. Hendershot, Iman Shojaei, Julian C. Acasio, Christopher L. Dearth, Babak Bazrgari

Biomedical Engineering Faculty Publications

Persons with lower limb amputation (LLA) perceive altered motions of the trunk/pelvis during activities of daily living as contributing factors for low back pain. When walking (at a singular speed), larger trunk motions among persons with vs. without LLA are associated with larger spinal loads; however, modulating walking speed is necessary in daily life and thus understanding the influences of walking speed on spinal loads in persons with LLA is of particular interest here. Three-dimensional trunk-pelvic kinematics, collected during level-ground walking at self-selected (SSW) and two controlled speeds (~1.0 and ~1.4 m/s), were obtained for seventy-eight participants: 26 with transfemoral …

Go to article

Dynamics Of Singlet Fission And Electron Injection In Self-Assembled Acene Monolayers On Titanium Dioxide, Natalie A. Pace, Dylan H. Arias, Devin B. Granger, Steven Christensen, John E. Anthony, Justin C. Johnson Mar 2018

Dynamics Of Singlet Fission And Electron Injection In Self-Assembled Acene Monolayers On Titanium Dioxide, Natalie A. Pace, Dylan H. Arias, Devin B. Granger, Steven Christensen, John E. Anthony, Justin C. Johnson

Chemistry Faculty Publications

We employ a combination of linear spectroscopy, electrochemistry, and transient absorption spectroscopy to characterize the interplay between electron transfer and singlet fission dynamics in polyacene-based dyes attached to nanostructured TiO2. For triisopropyl silylethynyl (TIPS)-pentacene, we find that the singlet fission time constant increases to 6.5 ps on a nanostructured TiO2 surface relative to a thin film time constant of 150 fs, and that triplets do not dissociate after they are formed. In contrast, TIPS-tetracene singlets quickly dissociate in 2 ps at the molecule/TiO2 interface, and this dissociation outcompetes the relatively slow singlet fission process. The addition …

Go to article

First Prev Next Last