Engineering Commons^™

Heat Transfer Coefficients Of Condensing Vapors, Charles Rocco Lipuma, Earl Adolph Nirmaier

Theses

The film coefficients of heat transfer for vapors condensing on a single horizontal tube have been measured for methyl, i-propyl, and n-butyl alcohols. The equipment used was specifically designed for these studies, and represents an improvement over that used by other investigators. The data collected were analyzed usingmodified Wilson method which is based on a rigorous theoretical analysis.

It has been found that the condensing film coefficients for methyl and i-propyl alcohols vary with the heat duty. This is to be expected from the analysis mentioned above. Me variation was found for n-butyl alcohol.

The observed values of the heat …

The Condensation Of Vapors From Gas-Vapor Mixtures, Stanley Anthony Mruk, William Charles Kraemer

Theses

Superheated mixtures of cyclohexane vapor and nitrogen gas were passed at various rates downward through a single tube condenser with the cooling water flowing countercurrently in an annular space outside the condenser.

The method of Colburn and Rougen for the design of cooler-condensers was applied and the calculated condenser lengths are compared to the experimental length.

Relatively good agreement with the design method was found for cases where there was little or no streamline flow of the gas-vapor mixture in the condenser. With increasing amounts of streamline flow* the design method tends to be increasingly conservative.

The Three Phase System N-Hexane - Aniline - Water, Charles S. Potosnak

Theses

This is a study of the three phase system - n-Hexane Aniline - Water at 50° Centigrade. The data obtained, coupled with data previously established at 36° Centigrade is used to predict a means of recovering aniline from 3-5% aqueous solutions by scrubbing with n-hexane.

Thermodynamic Properties Of Trimethylamine, John Bernard Riley

Theses

The thermodynamic properties of trimethylamine have been evaluated at temperatures from 32°F to 600°F and from the saturation pressure to 2000 lb/in² based on available experimental data. An equation relating the pressure, volume and temperature of the system has been derived for the range in which experimental data were available and it was used to evaluate the thermodynamic properties in this range. Values for pressure, volume, temperature, enthalpy and entropy have been presented in the form of tables and graphs.

Effect Of Concentration On The Mass Transfer Coefficient In The Liquid Film, Marvin Baker Schaffer, Philip Major Pomerantz

Theses

The effect of liquid concentration on the resistance to mass transfer across the liquid film is studied for an acetone-methyl isobutyl ketone-air system in a packed tower. The liquid film resistance is computed by measuring the overall resistance for various concentrations and subtracting the gas film resistance. The gas film resistance is determined at the same liquid and gas rates by measurements on the pure components.

In the theory developed to handle the calculations, it is assumed that the interface temperatures are the wet-bulb temperatures based on a dynamic equilibrium. This supposition is supported experimentally at a liquid rate of …

Ammonia Catalized Phenol Formaldehyde Resins, Murlin Charles Ehrgott

Theses

The literature on ammonia-catalyzed phenol-formaldehyde resins is reviewed and critical comparisons are made of the manner in which the ammonia-catalyzed resins differ from both the alkali- and acid-catalyzed resins.

Intermediate products formea during the initial stapes of the ammonia-catalyzed phenol-formaldehyde reactions, as reported in the literature, are tabulated and % N contents are calculated.

Experimental determinations of N content of resins with molar ratios of 1:1.25 phenol to formaldehyde with ammonia at 0.2, 0.5, and 1.0 moles per mole of phenol, show that at the 0.2 molar ratio of ammonia, all the N enters into the resin and remains during …

Electrodeposition Of Cellulose And Carboxy-Methylcellulose, Charles Edward Driesens Jr.

Theses

The previous work done by Frank Cozzarelli on the eleotrodeposition of cellulose from a sodium zincate-urea-cellulose system has been verified, except that zinc was found to deposit on the cathode at all voltages and current densities within the range of the optimum conditions for deposition. The optimum conditions are: voltage - 1.10 to 1.28 volts; current density 0.13 to 1.10 amperes/square foot; electrode material - copper. Current efficiencies range from 0.80 to 5.53%.

A chelate-like complex formed from the sodium zincate and urea which couples with the cellulose has been proposed as a possible explaination of the mechanism governing the …

Correlation Of Curtis And Gullett Equation For Viscosity Of Non-Newtonian Suspensions And Franks And Rinaldi Equation For Heat Transfer Coefficients, Irene S. Wisla, John L. Kukowski

Theses

Curtis and Gullett (7) developed an equation correlating the effect of velocity, concentration and particle size on apparent viscosity of non-Newtonian water slurries.

μ/μ_w=1.02(AK/GC)^.105

The object of this paper was to determine the validity of using the viscosity, as determined by the Curtis-GulLett (7) equation, in predicting the heat transfer coefficient of non-Newtonian fluids, where the suspending medium is something other than pure water . The authors used various concentrations of sugar solutions as the dispersion medium, for the slurries.

A dimensionless equation resembling the flittusBoelter equation with modified exponents and additional dimensionless groups has been developed …

A Study Of The Functional Stability Of Sunscreen Compounds, Jesse Howard Starkman

Theses

Previous work reported in literature, indicates that commercial sunscreen compounds were subject to breakdown on exposure to ultraviolet radiation with consequent change in their functional efficiencies.

These findings ware retested under conditions more closely approximating actual usage.

A new method of evaluation which closely correlates to actual experience in large scale usage, was applied. This method provides, from simple spectral data, a reliable index of physiological efficiency of the sunscreen compound. As a result, twelve commercial sunscreen compounds were exposed to ultraviolet radiation for varying periods. Analysis indicated that, contrary to the previous reports, no significant Changes in physiological efficiency …

A Study Of The Partial Oxidation Of Monosubstituted-P-Xylenes, Frederick John Honold

Theses

In the oxidation of 2-nitro-p-xylene (I) using alkaline potassium permanganate, the only product isolated was 2-nitro-terephthalic acid (II). Approximately half of the starting material was oxidized. The other half remained as unreacted starting material.

The chromium trioxide oxidation of 2-nitro-p-xylene (I) in glacial acetic acid, using sulfuric acid as a catalyst, yielded only 3-nitro-p-toluic acid (III).

The chromium trioxide oxidations, of 2-N-acetylamino-p-xylens (IV) with and without sulfuric acid catalyst, yielded no oxidation products which could be identified. About half of the starting material was recovered in each case.

In a low temperature alkaline potassium permanganate oxidation of 2-N-acetyIamino-p-xylene a small …

The Sulfonation Of Some Aromatic Compounds Using Sulfuric Acid In The Presence Of Thionyl Chloride, Paul Juergens

Theses

The rate of reaction in the sulfonation of some aromatic compounds with sulfuric acid was increased by the presence of thionyl chloride which, by reacting with the water of formation, effectively maintained the concentration of sulfuric acid above the level at which sulfonation can occur. The thionyl chloride had no measurable effect on the formation of isomers.

The sulfonstion reactions studied included those of toluene, naphthalene, bromobenzene, ortho-bromotoluene, and chlorobenzene.

Continuous Chlorosulfonation Of Benzene : I. Phase Relations, Henry Benjamin Lange

Theses

This work presents liquid-liquid equilibria data on a system suitable for continuous chlorosulfonation of benzene. Complete information is presented for the ternary, chlorosulfonic acid - sulfuric acid - carbon tetrachloride. A partial investigation of the ternary systems, chlorosulfonic acid - sulfuric acid - benzenesulfonyl chloride; chlorosulfonic acid - carbon tetrachloride - benzenesulfonyl chloride; and the quaternary system, carbon tetrachloride - benzenesulfonyl chloride sulfuric acid - chlorosulfonic acid is also presented.

Prediction Of Vapor-Liquid Equilibria, Daniel James Mchale

Theses

Several equations for predicting vapor-liquid equilibria from the physical properties of the components have been proposed in the literature. Two equations of this type proposed by O. Redlich and others have been investigated to determine their utility.

Results indicate the two equations give fairly satisfactory results for nearly ideal solutions, but are unsatisfactory for non-ideal solutions. Knowledge of molecular interactions in the solution would be necessary before the predictions could be used with confidence.

Prediction Of Liquid-Liquid Phase Equilibrium Data, William Frank Meola

Theses

This paper covers two methods for the prediction of liquid-liquid equilibrium data in ternary systems consisting of two hydrocarbons and a solvent and forming two liquid phases. One method is that of Pennington and Merril (ii) and the other is that described by Treybal (16), with some simplifying assumptions by the author. Both methods were applied to seven ternary systems in the present study. Five of the systems investigated were found to give rood agreement with experimental results. The assumptions made in deriving the equations for the two methods of prediction did not hold for the other two systems and …

Variation Of Thickness Of Hard Anodic Films, Alphons Raymond O'Konski

Theses

An investigation was made of the effects of varying processing conditions on the thickness of anodic films produced by the Martin Hard Coat (4) process on commercially pure aluminum and nine aluminum alloys.

This study was conducted to provide sufficient data for designing coating thicknesses on aircraft accessory parts that would conform to the close tolerances maintained in the course of manufacture of precision components. Coating thicknesses up to 0.0051 in. were obtained. Changes in electrolyte strength, temperature of the bath, alloy composition, and current density were made to see their effect on the thickness of the film and growth …

Correlation Of Crystal Growth Rates In Supersaturated Solutions, Josef Frank Palme

Theses

This investigation has shown that crystals of copper sulfate and magnesium sulfate when grown in supersaturated solutions exhibit a growth rate according to the following equation:

R_L = 5.0 (ΔCD_m)^1/ρU V_s^.292

where, R_L, is the growth rate in Microns/min, is the change in concentration, D_m, the diffusivity coefficient, , density of solution, U, viscosity and V_s, solution velocity past the crystal.

The equation shown demonstrates that a mass transfer process is taking place from the solution to the crystal surface, and that within the velocity range studied, there …

The Determination Of Thoria In Tungsten Electrodes, Louis Arthur Prince

Theses

Two methods of analysis to determine thoria (thorium oxide, ThO₂) content of thoriated tungsten electrodes are investigated.

Chlorination methods are shown to leave thoria residues contaminated with tungstic oxide which may not be removed by extended chlorination. Ignition of the sample in air before chlorination increases contamination. A correction for the tungstic oxide in the residue is obtained colorimetrically.

The classical hydrofluoric-nitric mixed acid method is modified and shown to be equally as accurate, less exposed to operator's error, and more rapid than chlorination methods. Thin-walled polyethylene beakers are preferable to platinum ware for dissolving the sample, and …

Power Characteristics Of Disc Type Agitator Impellers, Isadore Rubin

Theses

Experiments were conducted to determine the power required to drive disc type agitators and to observe the flowpattern and type of agitation produced in a baffled tank.

Power was measured by determining electrical energy input to a motor and subtracting motor transmission and friction losses previously established by calibration. Impellers were operated at speeds from 600 to 3700 RPM.

Power requirements in the turbulent flow region were correlated by the equation HP = PoL⁵N³ρ/550gc which was derived theoretically.

Reports of previous work on agitator power are discussed.

The Power Numbers (Po) established for the turbulent range, …

Isobaric Heat Capacity Of Propylene Over A Wide Range Of Temperature And Pressure, Joseph Patrick Tassoney

Theses

This work was done to make possible more accurate design calculatioas for processes that require accurate data on the heat capacity of propylene at elevated temperatures and pressures.

The effect of pressure and temperature on the isobaric heat opacity and the heat capacity at constant volume for propylene relative to the ideal gas state is presented. The results cover pressures from 0 to 9,500 PSIA and temperatures from 350°F. to 2240°F.

An equation was derived from the Benedict-Webb-Rubin equation of state. This equation gives the deviation from the ideal gas state of the isobaric heat capacity of propylene for the …

A Proposed Method Of Analysis For Vitamin A Acetate And Vitamin A Palmitate Bulk, Julian Anthony Volpe

Theses

An ethyl acetate solution of Vitamin A Acetate and Palmitate can be determined calorimetrically with the addition of concentrated hydrochloric acid in the proper ratio; one part of ethylacetate-Vitamin A solution to four parts of acid. A purplish-blue color is produced which reaches its maximum intensity within one minute and lasts for ten minutes. This color can be read in the Ilett-Summerson colorimeter using glass filter #54. Like many colorimetric determinations, this method is valid within certain concentration limits of sample, 20-225 milligrams of Vitamin A per final 5 milliliter aliquot.

The Reduction Of The Sodium Salt Of 2-Nitro-Phenol-4-Sulfonic Acid With Sodium Sulfide And Sodium Polysulfide, Robert Leslie Waer

Theses

Analytical techniques were studied for the determination of the purity of the sodium salt of 2-nitrophenol-4-sulfonic acid. The best method proved to be reduction followed by diazotisation.

The reduction of the sodium salt of 2 2-nitrophenol-4-sulfonic acid was carried out at various times and temperatures using sodium sulfide and sodium polysulfides as reducing agents. The reduction rate was very slow using sodium sulfide and only fair using sodium polysulfide solutions. Difficulties were experienced because of air oxidation.

The amount of reaction of sodium sulfide in the presence of a large excess of the sodium salt of 2 -nitrophenol-4 -sulfonic acid …

Use Of Liquid Sulfur Trioxide As A Sulfonating Agent For Organic Compounds, Herman Gustav Weiland

Theses

Dodecylbenzene was sulfonated with SO₃ and evaluated as to ash, sodium sulfate, degree of sulfonation, and was also compared with an oleum sulfonation. Its homolog, octadecylbenzene, was made, sulfonated, and found to be less effective as a wetting agent.

Two-ethylhexyl cinnamate, oleic acid, and propyloleate were also sulfonated with good yields and evaluated.

Yields in the sulfonation of Di-2-ethylhexyl maleate were very low. There was evidence of the SO₃ splitting the ester and oxidising it to maleic acid.

The reduction of 9-octadecenophenone, according to Clemmenson's Method, led to the formation of a polymer.

A Generalized Correlation For The Effect Of Pressure On The Isobaric Heat Capacity Of Gases, Alvin Harvey Weiss

Theses

A generalized correlation is submitted for the deviation of the isobaric heat capacity of hydrocarbons from the ideal state. The range of conditions included is from reduced pressure = 0.2 - 15 and reduced temperature = 1.0 - 5.5. The curves presented have been based on data calculated from the Benedict - Webb - Rubin Equation of State, which is believed to be the most accurate method presently available for caleulating the heat capacity deviation.

The results indicate that the order of magnitude of the correction ts quite large, especially in the critical region. The average absolute error of this …

The Recovery Of Krypton From Dilute Gas Mixtures By Elution Techniques, David Graham Brown

Theses

An analytical method has been empirically developed for the analysis of dilute inorganio inert gas mixtures.

The method is based on a combined sorption-elution technique which makes possible the resolving of complex inert gas mixtures into their constituents.

Particularly the recovery of krypton from dilute gas mixtures was accomplished. Recovery efficiencies were as high as ninety-eight percent, while the average krypton purity was better than ninety-nine percent.

Heat Transfer Coefficients For Condensing Vapors On A Horizontal Tube, Maurice Edward Brown, Rodwin Edwin Gulick

Theses

Film coefficients of heat transfer for vapors condensing on a smooth horizontal tube have been experimentally determined by many investigators. The so-called Thermocouple Method and the Wilson Method, have been used and generally accepted as the two methods for determining these film coefficients. A number of different organic vapors have been studied on various condensing surfaces. Nusselt has also developed a theoretical equation,

hN = 0.725 4√k_f³ρf²λg/D_oμfΔtcf

for evaluating the film coefficients of vapors condensing on hori?zontal tubes.

The earlier investigators have shown that theoretical values, hN do not check with experimentally determined …

Bis Phenol Epichlorohydrin Condensate Modification Of Alkyd Resins, Raymond Francis Carmody

Theses

A method is given for the modification of alkyd resin systems with Bis-Phanol Epichlorohydrin Condensates.

The properties of the modified alkyd resins are evaluated using similar unmodified alkyd resins as reference.

A theory of linear esterification is postulated.

The Analogy Between Heat And Mass Transfer In Packed Beds, Jasper Joseph Correnti

Theses

An operation which recurs in many branches of chemical engineering is that in which a fluid - gas or liquid - is passed through a bed of granular solids for the purpose of removing from, or adding something to the fluid (or both). In the oil and sugar industries, oils or syrups are passed through beds of adsorbents to remove impurities causing color and other undesireable effects. In the recovery of volatile solvents, air charged with solvent vapor is passed over solid adsorbents. In leaching, liquids are passed through beds of solids to remove some constituent of the solids. In …

The Effect Of Reduced Pressure On Variables In Distillation, Joseph Peter Cummins

Theses

To determine the effects of reduced pressure on pressure drop and holdup in distillations seven different liquids were distilled at varying rates at atmospheric pressure and under vacuum at pressures down to 50 mm Hg, using protruded stainless steel packing. Pressure drop and holdup were found to vary exponentially with masste at each pressure. At constant mass rate pressure drop was higher for decreased head pressure. Use of material of higher molecular weight led to lower pressure drop at same rate and pressure. Greatest effect of pressure on pressure drop was observed below 300 mm Hg. Liquid holdup was not …

Heat Capacity Ratios Calculated From The Benedict-Webb-Rubin Equation State, Edward George Delaney

Theses

The ratio of the isobaric heat capacity to the constant volume heat capacity has been calculated over a range of temperatures and pressures for the following hydrocarbons: methane, ethylene, ethane, propane, and n-butane. Graphs and tables of calculated data are presented showing the effect of temperature and pressure on the ratio of the heat capacities for these compounds.

The deviations of the heat capacities from ideal gas behavior were calculated by previous investigators from an equation based on the Benedict-Webb-Rubin equation of state, Experimental data were used to evaluate the heat capacities of the ideal gases, and were used together …

Intermediates For P-Acetamidocinnamic Ester Synthesis, William Grayson Fix

Theses

After a review of the various methods found in the literature, a series of reactions were selected which were reported to have good yields.

Using p-nitrotoluene as a starting material, a simultaneous oxidation and reduction with sodium polysulfide was investigated as a means of making p-aminobenzaldehyde. Experimental procedures and yields were reported, and improved methods of recovery were described.

Using p-aminobenzaldehyde from the first reaction, a condensation with malonic acid, in pyridine-piperidine medium, was investigated as a means of preparing p-aminocinnamic acid.

A recommended procedure was described, and some suggestions were made concerning the completion of the synthesis of p-acetamidocinnamic …