Engineering Commons^™

A Study Of Pulsation Of Chest Wall Using Microwave Interferometer, Paul Zeno

Theses

The microwave interferometer is utilized to pick up vibrations of the anterior chest wall produced by the cardiac activity. The objective of this project is to find the causes of different peaks in the output of the microwave interferometer. The output of the microwave interferometer is recorded simultaneously with EKG and jugular pressure pulses. Eighteen subjects had their mechanical vibrations of the chest wall, EKG and jugular pressure pulses recorded. The processed interferometer data, when compared with EKG and jugular pressure pulses appear to have a close relation to the mechanical events in the cardiac cycle. Four peaks in the …

Computer Aided Finite Element Stress Analysis Of A Three Dimension Mandibular Bone Model Using I-Deas Software, Yixiong Xu

Theses

A three dimensional model of half of the mandibular bone, with 487 tetrahedra elements and 1,047 nodes, is established and analyzed by means of I-DEAS software. The masseter muscle is assumed to be 15° deviation from y-axis, and the Umetani boundary conditions are allowed to be varied. A 337 lb force was applied along the midline of the mandible to simulate a trauma force caused by the auto accident. The maximum principal stress is 18,400 psi and the minimum principal stress is -1,340 psi. Depending on the experimental results of dispalcement and maximum principal stress, the conclusions are drawn: 1) …

The Thermal Model Of The Rat Under Hemorrhagic Shock Hypothermia With Microwave Intervention, Liu Zhe

Theses

A whole body thermal model simulating heat distribution and temperature regulation in rats during hemorrhagic shock and during post-shock microwave core rewarming period was developed. An electrical circuit was used to simulate the thermal system and a software named PSpice? was used to analyze the circuit. The temperature regulation as the result of the simulation is demonstrated to match the measured temperature histories of rats in hemorrhagic shock and the microwave rewarming experiment.

The blood pressure drop and cardiac output decrease were considered in the simulation and the so called "set point temperature" was investigated in the model. Linear decrease …

Forward Kinematics Solution Of A Special Class Of General Stewart Platforms, Jian Li

Theses

A Stewart platform is a fully parallel, six-degree-of-freedom manipulator mechanism. A platform manipulator has a fixed platform acting as base, a mobile platform on which end-effector is mounted, and in-parallel kinematics chains (legs) between the two platforms. Although some direct position kinematics solutions for Stewart platforms of simplified geometry have been represented, to the best of our knowledge, no close-form direct kinematics solution for the general Stewart platform is available yet.

A common feature of six-degree-of-freedom Stewart platform of simplified geometry is the use of pairs of concentric ball joints. Due to inevitable manufacturing and assembly errors, practically there are …

Development Of A Model For An Objective Minimum Resolvable Temperature Difference Characterization Of An Infrared Camera, Christine Issa Mourad

Theses

The parameter almost universally adopted by the infrared community for describing the overall performance of a thermal imaging camera is the minimum resolvable temperature difference. Unfortunately, this criterion is subjectively determined by a group of observers and as a consequence significantly varying results can be obtained at different times. This project describes work on an approach which ultimately aims to replace the observers by a computer-aided installation that simulates the human process by which the MRTD is estimated. The simulation is based on a direct measurement of signal to noise ratio in the image of the target and a determination …

Heat Resistance Measurements With The Portable Calorimeter Box, Philipp G. Mohr

Theses

The heat resistance of wall section materials has been investigated under laboratory conditions, but reliable measurements in-situ with non-steady weather conditions are not yet available. The portable calorimeter box is designed to make field measurements to test the thermal performance of building envelopes. The experimental setup and the equipment for thermal measurements are described, as well as the computer program for data reduction. The characteristics of the portable calorimeter box and the problems of non-controllable test conditions have been investigated.

Forty experiments were completed. Sixteen preliminary experiments investigated problems associated with insufficient setups; such as a short duration, only partly …

Translation Of Images On The Hypercube Using Leaf Codes, Bhavesh Patel

Theses

Image processing is used for manipulation of pictorial images. Image analysis applications are typically characterized by the need to process large quantities of image data. Some of the important transformations or operations which are car¬ried out by image processing systems are translation, scaling, superposition and rotation. Algorithms have been developed to carry out these transformations on image regions represented by quadtrees. Gargantini introduced an algorithm to translate an image region represented by a linear quadtree or leafcodes. A linear quadtree is a space efficient data structure used for storing digital images. Ziavras et.al. have proposed a modification of Gargantini's algorithm …

Design Of Holographic Optical Interconnections, Su-Chiou Tsay

Theses

Optics have many advantages over electronics in interconnecting systems together, particularly in terms of higher transmission speed and better immunity to noise. Optical interconnections may be used at all levels of computing: for local area networks, between processors or memory elements, and between boards.

In this thesis, we attempted to generate a new type of computer hologram for optical interconnection purposes. The holographic method is very promising whenever integrated optical interconnections are considered. In this research we have tried two designs: the shortest path grating design which can maximize the global output energy and the single input maximum output grating …

Cause And Effect Diagrams For Process Analysis And Control, Philip Thomas

Theses

Cause and effect diagrams can be used as an effective tool for identifying the possible causes of a quality problem. Using this diagram one can go deep into the causes of the problem and take proper remedial action. Several graphical techniques like matrix diagrams, systematic diagrams, etc., can be combined with this tool to better represent the cause effect relationships. While a quantitative approach of this technique is feasible but limited, there are useful applications based on qualitative approach to this technique. The objective of this thesis is to propose a quantitative approach to the cause and effect diagrams especially …

Behavior Of High Strength Concrete And Slender Reinforced Concrete Columns With And Without Steel Fibers, Lin Showmay Hsu

Dissertations

A series of compression tests are conducted on 3 in. by 6 in. cylindrical specimens using a modified testing method that give the complete stress-strain behavior for both plain and fibrous high strength concretes with or without tie confinements. The volume fractions of fiber in the concrete are 0%, 0.5%, 0.75%, and 1.0%, respectively. Empirical equations are proposed herein to represent the complete stress-strain relationships of high strength and high strength fibrous concretes with compressive strength exceeding 10,000 psi. Various parameters are studied and their relationships are experimentally determined. The comparison between the experimental and analytical results shows to have …

Fabrication And Characterization Of Gated Silicon Field Emission Micro Triodes, Nanchou Liu

Dissertations

This dissertation describes the fabrication technology and characterization of a gated silicon field emission micro triode that is a novel electron tunneling device for generating electron emission into a vacuum. Conic (point) and wedge field emitter structures with nm-scale radii were fabricated in silicon and GaAs by etching, MOCVD and dry oxidation. A new self-aligned process was developed for fabrication of vertical field emission triodes. This process allows control of gate opening to less than 0.5 μm diameter without the need of electron-beam writing. It also provides a planar gate electrode and a thick dielectric layer for reduction of the …

The Influence Of Pore Fluids On Shear Strength And Stress-Strain Behavior Of Granular Soils, Prasanna Ratnaweera

Dissertations

When a dry granular soil is subjected to an external load, the stresses are transferred through mineral to mineral contacts. The shear strength of such a soil is governed by its contact properties. Presence of a thin layer of fluid between mineral to mineral contacts in a saturated soil will alter its contact properties. Therefore any change in the physical properties of pore fluid can logically be reasoned to influence the deformation characteristics of granular soils.

To investigate the influence of pore fluid viscosity on shear strength and stress-strain behavior of a soil, a series of consolidated drained triaxial tests …

Expert System For The Injection Molding Of Engineering Thermoplastics, Tzy-Cherng Jan

Dissertations

Injection molding of engineering thermoplastics is the most widely used manufacturing method in industry. It is a priority to maintain a deviation-free operating environment to ensure high quality, low cost manufacture. An expert system for the injection molding of engineering thermoplastics has been investigated. The system can be used to attenuate the deviations experienced during the injection molding of engineering thermoplastics. The system is coded in C programming language.

The resolution procedures of this system include two stages such as the definition of declarative knowledge and the procedure of corrective actions. In the definition of declarative knowledge, all of the …

A Study On Radical Scavenging And Magnetic Resonance Imaging Characteristics Of Stable Radical Nitroxides, Shiey-Shiun Horng

Dissertations

Several nitroxides have been prepared for study of their image enhancement capability. These nitroxides contain different nitroxyl moieties within one molecule. On MRI examination for the nitroxides prepared, TEMPO and HPTPO are better due to their better water solubility, even though some of the others have more nitroxyl centers available. The intensity response is linear with respect to concentration in the range studied in most of the cases except for HPTPO, whose intensity finally reaches maximum when its concentration is higher than 10 mM.

Three sources of biomass, namely, liver microsomes, whole-cell yeast and a bacterial activated sludge consortium, have …

Design For Productivity Using Gd&T, Srihari G. Acharya

Theses

No abstract provided.

Mineralization Of 2-Chlorophenol Using A Hollow Fiber Ultrafiltration System In Combination With A Reactor Containing An Immobilized White Rot Fungus, Sheau-Ming Tung

Theses

Phanerochaete chrysosporium, a white rot fungus was immobilized on a packed-bed reactor, and was used to mineralize an aqueous stream contaminated with 50 ppm of 2-chlorophenol. Hollow fiber ultrafiltration membranes (for 5,000 daltons and 10,000 daltons molecular weight cut-oft) were utilized to retain the extracellular enzyme resulting from the immobilized fungus in a recirculation loop outside of the reactor.

It was found here that the concentration of proteins (roughly proportional to the extracellular enzyme releasd by the fungus) does not correlate with the rate of degradation of 2-chlorophenol in the system. The protein was concentrated 1.5 fold in the recycle …

The Acoustic Properties Of Human Femoral Bone, Mark Lacianca

Theses

Over the last decade, interest has grown in the use of the scanning acoustic microscope (SAM), with a single lens being used for both transmitting and receiving the acoustic signal. A major objective of this thesis was to determine if the transmission and ultrasonic techniques yield similar "quantitative" results, when measuring the elastic constants of human femoral bone. The transmission technique has been used since 1970 to yield values for the elastic properties of calcified tissue. Previously the SAM has been used as a qualitative tool, where an acoustic impedance map is produced. This map can show areas of bone …

Design For Manufacturability And Assembly, Srinivas Mullapudi

Theses

This report presents a study of the various concepts of design for manufacturability and assembly with some case studies, and examples.

The goal of DFM is reduction of parts and simplifying assembly process. A simple faucet has been studied and attempts have been made at re-designing the same using the techniques of design for manufaturability as postulated by Boothroyd, Dewhurst and Henry Stoll.

Development Of The Interface Between Cad And Waterjet Nc Systems, Sivayasivan Sambandan

Theses

There has been a continuous need in the present to develop softwares that provide interface between cutting machines and computer control. There involves a number of complex stages from the birth of an algorithm, to develop such software, till the end where it successfully gets tested and implemented. Cutting Path Simulation (CPS) is a partially developed software designed to model 2-d and 3-d objects and down load them to water jet cutting machine. Additional menus were created in the software to perform specific functions. Bugs that existed in the previously done work were removed. Investigation was conducted on the feasibility …

Planning Of Optimal Transit System Design, Yongning Liu

Theses

This study presents a methodological approach for finding an optimal design of bus transit service in an urban transportation corridor with elastic demand and under various objective functions. Service design decision variables to be optimized include the route length, route density, headway, number of stops and stop spacing pattern. The objective functions that optimize the transit system design include: minimizing operator cost, maximizing profit, minimizing sum of operator and user costs and maximizing the users' net benefits.

The analysis uses an elastic demand function wherein the number of trips are sensitive to the quality of service provided and price charged …

Removal Of Volatile Organic Compounds (Voc's) Acetone And Ethyl Alcohol Emitted In The Manufacture Of A Multi-Base Propellant, Yih-Leu Liu

Theses

The Production Base Modernization Activity located at Picatinny Arsenal, initiated this study for the removal of the low concentrations of VOC's, acetone and ethyl alcohol emitted from the mixer operation and the forced air dry unit in the manufacture of a multi -base propellant. Air pollution requirements necessitate 85 % removal of the VOC's prior to discharge of the vent gases into the atmosphere. Because of the availability of sulfuric acid, it is proposed to use 70 percent or stronger acid as the absorbing agent in a recirculating acid absorption tower.

Vapor - Liquid Equilibrium ( VLE ) data were …

Cost Deployment Based On Quality Function Deployment, John Goceljak

Theses

A methodology for Cost Deployment based on Quality Function Deployment (QFD) architecture is developed and explained. Following a comprehensive review of Quality Function Deployment terminology and composition, a house-of-quality is developed, and matrix correlation methodologies are discussed. Current applications are presented to illustrate the scope and adaptability of this quality assurance tool. In addition, an exercise in product design and review is conducted to illustrate a unique approach to cost deployment. Quality Function Deployment issues, including software, consulting, and preferred practices are also presented.

Quantitative Assessment Of Myocardial Oxygen Supply And Demand Using A Dynamic Model Of The Cardiovascular System, Badrinath R. Puranic

Theses

A quantitative understanding of the changes in coronary, pulmonary and systemic hemodynamic variables and their effect on myocardial supply and demand is important to the better management of anesthetic care of patients with impaired cardiac function. Animal studies have identified those hemodynamic factors that play an important role in determining the balance between oxygen supply and demand for the myocardium. These include myocardial contractility, left ventricular end-diastolic volume, systemic arterial pressure, systemic vascular resistance, and heart rate. The interactions of these factors are complex and their combined effects on myocardial oxygen supply and demand are difficult to predict a priori. …

Errors In Constant-Velocity Shaft Couplings, Philip M. Remington

Theses

A Multiloop spatial system of rotations is used to represent a shaft coupling, allowing a transmission plane which may deviate from the plane of symmetry to be specified. The plane of transmission, for intersecting input and output shaft axes, is the locus of intersections of screw axes that compose the system. By prescribing the transmission plane outside of the plane of symmetry (commonly called the "homokinetic plane" or "bisecting plane") to pecified orientations, a phase shift between the input and output shaft rotational displacements will he quantified. The rotational phase shift between the input and output shafts can be evaluated …

A Study Of Annular Slurry Jet For Abrasive Waterjet Cutting, Thomas Kuriakose

Theses

The objective of this project is to study the performance of an annualr slurry jet nozzle for abrasive waterjet cutting. This nozzle has been invented by Avraham. Harnoy, Department of Mechanical Engineering, NJIT and presented to the patent committee of NJIT in May 1990. This study includes design and development of prototyes and testing of their performance. Moreover, it includes initial theoretical study of the flow behavior.

The idea is based on the merging of a high velocity pure waterjet with an annular jet of a slurry of water and abrasives at low velocity. The two jets merge outside the …

Mathematical Model And Simulation Of The Progression Of Cutaneous T-Cell Lymphoma, Maria L. Agostinho

Theses

A simple mathematical model and simulation of the progression of cancer with particular emphasis on Cutaneous T Cell Lymphoma was investigated. The mathematical model consists of a set of differential equations that first satisfies the homeostasis levels of the different components present and second predicts the dynamics during a diseased or unhealthy condition. The simulation was done using a FORTRAN program for integrating the differential equations.

Simulation of the immune system is important in evaluating the usefulness of particular sorts of biologically targeted therapies and in selecting the most promising treatment strategies for clinical trials. In particular, the effects of …

Adaptive Map Configuration And Dynamic Routing To Optimize The Performance Of A Satellite Communication Network, Santhalingam Balasekar

Theses

Availability of alternate routes are shown to enhance the performance of non-hierarchical circuit switched networks at moderate load conditions on which the networks typically operate. But alternate routes introduce instability at heavy and overloaded conditions and at these load conditions the network performance is found to deteriorate. To alleviate this problem, one of the control mechanism used is to reserve a fraction of the capacity of each link for direct routed calls. In this work, the feasibility of changing the facilities of a satellite network is taken advantage in optimizing the performance of such a network. A mesh connected, circuit …

Automatic Motion Analysis Of Colliding Spheres, John Vijayakumar Caesar

Theses

Motion analysis is useful to compute linear and angular velocities and acceleration of an object from a sequence of images. This thesis is part of an investigation to compute the translation and rotation velocities needed to determine the collision parameters of two colliding spheres. This involves the tracking of the spheres and feature points on the spheres over a time interval. An experimental setup releases two spheres such that they collide and a high speed imaging system, i.e., Kodak Ektapro 1000 is utilised to record the motion of the spheres. The imaging system is capable of recording at a speed …

Point Pattern Matching By Heuristic Methods : A Genetic Algorithm And Simulated Annealing, Erh-Chin Chen

Theses

The problem we consider is to find a subset of points in a pattern that best match to a subset of points in another pattern through a transformation in an optimal sense. Exhaustive search to find the best assignment mapping one set of points to another set is, if the number of points that are to be matched is large, computationally expensive. We propose two stochastic searching techniques - a genetic algorithm and simulated annealing to search for the best ("almost the best") assignment efficiently. To make the comparison between GA and SA fair, we introduce a piece-wise linear cooling …

Uses And Applications Of Artificial Intelligence In Manufacturing, Manojkumar H. Desai

Theses

The purpose of the THESIS is to provide engineers and personnels with a overview of the concepts that underline Artificial Intelligence and Expert Systems. Artificial Intelligence is concerned with the developments of theories and techniques required to provide a computational engine with the abilities to perceive, think and act, in an intelligent manner in a complex environment.

Expert system is branch of Artificial Intelligence where the methods of reasoning emulate those of human experts. Artificial Intelligence derives it's power from its ability to represent complex forms of knowledge, some of it common sense, heuristic and symbolic, and the ability to …