Engineering Commons^™

An Adaptive Asynchronous Cdma Receiver And Its Convergence Analysis, Lizhi Zhong

Theses

An adaptive CDMA receiver scheme assuming perfect synchronization has been generalized in this thesis to the asynchronous channel, a much more practical assumption of the real system. Similar formulas are derived and as its synchronous version, it is still near-far resistant and requires no knowldge [sic] of received signal amplitudes and training sequences. Thus, sophisticated high-precision power control and user power estimation are not necessary and the receiver is particularly useful in mobile communications since it can adjust itself adaptively to changes in the power of the users. Tile convergence and transient behavior of the receiver are also investigated and …

Development Of A Multi-Lead Trans-Thoracic Impedance Pneumograph For Heart Rate Variability Studies, Curtis Bashford

Theses

In this study, a device that measures respiratory tidal volume and ECG for use in heart rate variability studies, was designed, built and tested. The device developed is a Multi-Lead Trans-Thoracic Impedance Pneumograph, which determines tidal volume on a breath by breath basis, utilizing both hardware and software. It uses standard ECG electrodes which provide increased comfort and inability to the subject over traditional spirometry methods. The device operates similar to traditional bipolar impedance pneumographs except that instead of only one lead (electrode pair), four leads are acquired simultaneously using time-division multiplexing; providing data from different locations and vectors on …

Time Domain And Frequency Domain Analysis Of Myoelectric Signals During Muscle Fatigue, Rakesh M. Maniar

Theses

Spectral analysis of the EMG signal is a useful tool for studying the complex phenomena of fatigue. The spectral parameters of mean frequency and median frequency, and the time domain parameter of root mean square have been used to measure localized fatigue.

The normal values of median frequency and its decline with fatigue have not as yet been determined in healthy subjects. This should be done in order to apply spectral analysis for clinical evaluations of abnormal populations. Normal median frequency values and its slope were established in this work for the upper extremity muscles of biceps, triceps and deltoid …

Implementation Of Time-Frequency Distribution Software And Its Use To Study Biological Signals, Mansour Adib

Theses

The joint time-frequency signal representation has received considerable attention as a powerful tool for analyzing biological signals. It combine time-domain and frequency-domain analyses to yield a potentially more revealing picture of the temporal localization of a signal's spectral components. In this research we have developed algorithm which implement time-frequency signal analysis techniques on a computer system. Its primary function is to produce a variety of time-frequency representations and plots from the time series. Numerous generated signals were used to justify our computer algorithm.

Variety of time-frequency distribution were utilized to expand the concept of spectral analysis of heart rate variability, …

Use Of Multiple Transmitters For 3-D Non-Intrusive Particle Tracking, Jitesh H. Agrawal

Theses

A method for non-intrusive tracking of a particle in 3-dimensional space, based on processing of signals emitted from a transmitter embedded in the particle, is being developed. This method uses a mathematical model, which predicts the induced signal in receivers present in the vicinity of flowing particle, and supporting numerical techniques. Specific application aspects related to improving the accuracy of this method are presented.

The focus here is the development of flexible software capable of processing information coming from multiple transmitters with known distinct spatial orientation. Implementation aspects of modified existing empirical corrections for improving model-reality agreement, and new techniques …

Model Parameter Identification For Rod And Cone Oscillatory Potentials, Kehur Banker

Theses

The use of signal modeling of the oscillatory potential (OP) of the electroretinogram (ERG), in the study of cone-rod interaction is investigated. ERG response data were analyzed for red, orange, blue and white flashes on no background and with red flashes on a blue background (to suppress rod responses). The OP signals were extracted from the ERG by digital bandpass filtering and a signal model was fitted through a simplex algorithm to produce the parameters including "OP envelope-amplitude", latency in terms of "center-time" of the OP-envelope and OP frequency. Amplitude for red flashes with or without a blue background showed …

Wear Of Polyethylene And Hylamer On Cobalt-Chromium : A Knee Simulator Study, Alessandro F. Canonaco

Theses

Two tests were conducted to examine the wear characteristics of tibial bearings used in total knee replacement systems. Each test consisted of six A/P Glide Tibial Bearings each having a conical control arm. The plastic portion of the conical bearings were all made of UHMWPe. Each of these bearing systems was mounted onto a Co-Cr alloy tibial platform and Co-Cr alloy LCS (low contact stress) femoral component . These test samples were mounted onto the New Jersey Mark III Knee Simulator System. The simulator was configured to produce flexion and axial rotation to simulates normal gait. Each test ran at …

Investigation Of Velocity Distribution Within High Speed Waterjet, Hong Cao

Theses

The aim of this research was to investigate velocity distribution within the water jet at different conditions of jet formation. The water jet (WJ) velocity was measured by the use of Laser Transit Anemometer (LTA) and statistical technique which improved the accuracy of the velocity determination.

The velocities were measured for different diameters of the sapphire nozzle under different water pressures at different axial stand off distances and radial distances across the jet. The experiments performed in this study enabled us to evaluate the effects and conditions of the water jet on the velocity distribution. The acquired results provide information …

A Comparison Between Revealed Preference (Rp) And Stated Preference (Sp) Based On Results Of Simulations, Qiuzi Chen

Theses

This research quantifies the potential biases resulted from two different data generation methods used in transportation modeling: Revealed Preference (RP) and Stated Preference (SP) techniques. Revealed Preference technique is the conventional approach to generate data. It relies on observed or reported data of actual behavior. Stated preference technique is a new data generation method. It creates transportation scenarios using hypothetical data. Conventional studies favor the use of revealed reference. However, full description of advantages and weaknesses of using revealed preference technique is not available in literature, neither point-to-point comparison between stated preference and revealed preference techniques. This research contributes to …

Performance Evaluation And Sequence Control Of An Automatedmanufacturing System, Vijaykumar D. Desai

Theses

In an automated sequential manufacturing system Programmable Logic Controllers (PLC) are widely used. As the control specification varies, the control software needs to be rewritten to accommodate the new specification. Since PLC has high flexibility, one can update the current system while it is running thereby making easier implementation. In order to design flexible, reusable and maintainable control software, a good modeling tool is required. Petri nets are such a tool. Which facilitates analysis of behavioral properties, performance evaluation, and systematic construction of discrete event simulators and controllers. In this thesis a system with one robot and five sequential work …

Viscoelastic Effects On Parallel Flow Stability, Transition To Turbulence, And Turbulent Flow, Michael Garofalo

Theses

The classical two dimensional theory of stability of parallel flow is extended to viscoelastic fluids. How the elasticity of the fluid affects the point of stability and determines the point of transition to turbulence is analyzed. In addition the magnification of disturbances is elucidated. This study is based on a viscoelastic constitutive equation which has been successful in predicting the experimental trends of various unsteady high shear rate laminar flows. A viscoelastic stability equation which is an extension to the Orr-Sommerfeld equation for a Newtonian fluid is derived and solved for a flow between parallel plates superimposed by a two-dimensional …

Development Of An Expert System To Facilitate A Pump Manufacturing/Warehouse Facility, Muhammad Mutahir Ghauri

Theses

The objective of this study is to evaluate the effectiveness of utilizing an expert system technology as it relates to manufacturing. It appears that our industries are still uncertain about this technology. In the first phase of this study, procedure for deployment of this technology is discussed. Secondly a knowledge-based expert system is developed, using a VP-Expert microcomputer shell. The system is made of three modules, inventory module, cost analysis module, and decision making module (for the selection of pumps).

A warehouse was selected for the analysis, which carries the finished product in the form of pumps. The quantities and …

The Mobile Satellite Service (Mss) Systems For Global Personal Communications, Kiho Lee

Theses

A worldwide interest has arisen on personal communications via satellite systems. The recently proposed mobile satellite service(MSS) systems are categorized four areas: geostationary earth orbit(GEO) systems, medium earth orbit(MEO) systems, low earth orbit(LEO) systems, and highly elliptical orbit(HEO) systems. Most of the systems in each category are introduced and explained including some technical details. The communication links and orbital constellations of some systems are analyzed and compared with different categories, and with different systems. Some economical aspects of the systems are mentioned. The regulatory issues about frequency spectrum allocation, and the current technical trends in these systems are summarized.

Mechanical Behavior Of Polystyrene Foam Bead Lightweight Concrete, Hai-Ying Ni

Theses

This thesis is designed to investigate the effect of porosity on the mechanical properties (strength and modulus) of concrete, and to evaluate the effect of silica fume on the mechanical properties of the polystyrene foam bead lightweight concrete. In this research we made the lightweight concrete by using polystyrene foam beads as light weight aggregate and studied its mechanical properties in detail. Due to the near zero density and modulus of foam beads, we were able to consider it as "porosity". We could then control porosity in concrete by varying foam bead volume fraction.

In our experiments we used the …

Area And Perimeter Measurements Of Cells With Bound Fluorescent Antibodies, Aicha Weiss

Theses

The objective of this research was to geometrically analyze the characteristics of cells, specifically area and perimeter. The images were transferred from HP A900 system to an AVS work station. The images were visualized and manipulated by the AVS which permits the distinction between the cell body, fluorescent object, and background. The intrinsic geometry of the cell was determined by using image processing algorithms written in C. The images were then passed through a threshold filter, thereby yielding a black background and a white cell body. The perimeter calculation was then applied to the black and white images. Two test …

Case Study Of Assembly Defects In Manufactured Products, Michael J. Withka

Theses

Design for Quality Manufacturability (DFQM) is a design tool that empowers engineers to create designs that are easily and effectively transformed into manufactured products. The goal of this methodology is to make designers aware of design characteristics that may lead to product defects during the assembly process. Acknowledging the possibility of these defects will enable the designer to institute design modifications early in the design phase. The benefits realized in this approach are a reduction in the number of defects in the finished product, reduced product cycle times, a reduction in monitoring costs and a reduction in time-to-market.

This thesis …

A Systematic Approach To Defense Diversification, Sathappan Venkatachalam

Theses

The decline in defense spending has resulted in defense dependent companies seeking new markets through re-designing existing products, developing new products and restructuring their businesses. Defense diversification is defined as the process of transitioning a defense company's core capabilities (technologies, products, services) into commercial and non-Department of Defense government markets. A combination of site visits and review of the literature on defense diversification demonstrates the need for diversifying companies to adopt a systematic approach.

A concurrent new product development/product redevelopment model is proposed, based on the principles of concurrent engineering. The model consists of an eight phase development cycle and …

Scheduling Of Flexible Manufacturing Systems With Automated Guided Vehicles Using Petri Net Models, Hua-Sheng Chiu

Theses

In this thesis, Petri net models for Flexible Manufacturing Systems (EMS) are constructed. A firing sequence of the Petri net from the initial marking to the final marking can be seen as a schedule of the modeled FMS. By using the branch-and-bound algorithm, an optimal schedule of the FMS can be obtained.

Automated Guided Vehicle Systems (AGVS) are increasingly used for material handling in factories and warehouses. An AGVS can reduce labor costs and is ready to be integrated into an automated factory. This thesis presents two AGVS models (shared and duty) which integrate the control of AGVS with the …

Single-Axis Agonistic Motion Control System With Electro-Magnetic Actuators, Alexander Rokhvarg

Theses

A novel single-axis motion control system using solenoid electromagnet actuators is built and successfully controlled using a non-linear real-time control algorithm. Procedures for defining and modeling the electromagnetic actuator are established and implemented. Discrete-time nonlinear control law with global asymptotic stability and zero steady-state error is designed and numerically optimized. Stable operation with small-signal 0dB crossover frequency of 370 Rad/sec and positioning RMS steady-state error of better than 4 micron is achieved. Time domain parameters are verified on a working prototype. A step reference response positioning a 0.35 Kg mass payload over 1 cm travel in under 30 milliseconds is …

Synthesis Of Silicon Oxide/Vycor Composite Membrane Structures By An Optimized Lpcvd Process, Abhijit Datta

Theses

This study is focused on development of highly selective ceramic membrane structures consisting of silicon dioxide films synthesized by low pressure chemical vapor deposition (LPCVD) on mesoporous Vycor substrates. The ability of easily altering the composition of such films by varying the LPCVD processing parameters affords the opportunity of microengineering the pore structure by reducing the diameters of pre-existing pores in the support. The process parameters investigated include, deposition temperature, total pressure, and flow rate of oxygen. Both the kinetics and select properties of the deposits were examined. The growth rate as a function of temperature was seen to follow …

Simulation Of Activity Rhythms In The Hamster, Paul Qassis

Theses

In this research, an effort was made to better understand light-dark cycles which influence the physiological and psychological rhythms, circadian rhythms and their behavior. The research concentrated on mathematically modeling circadian rhythms (specifically hamsters' circadian activity rhythms) and establishing a physical correlation and creating a meaningful relationship between the mathematical model's parameters and the real biological oscillators which are responsible for these rhythms. The internal nature of the circadian rhythms is unclear. There is insufficient information and empirical data that describe them. Indirect means have to be employed for the description and exploration of such rhythms. Extensive real data analysis …

An Investigation Into Artificial Intelligence Based Generative Computer Process Planning, William Tereshkovich

Theses

The process planning function can be further optimized with the introduction of an intelligent software package such as an Artificial Intelligence based Generative Computer Process Planning System. An AI based CAPP system, also categorized as an expert system, provides the vital link between design and manufacture, a "bridge" of knowledge in the information chain of manufacturing engineering. With the increasing role of computers in the process planning function, planning has become easier, faster, and more efficient.

This thesis provides an explanation of the process planning function and how artificial intelligence will improve it. Topics in AI techniques and procedures, knowledge …

A General Method For The Inverse Kinematics Of Rotational Displacements In Spatial Mechanisms, John D. Kliminski

Theses

An iterative technique was developed to solve the inverse kinematics problem for the joint rotations in both closed-loop and open-loop spatial mechanisms and robotic manipulators in any prescribed configuration. The method is based on fixing one link in space and maneuvering the other links to form a closed chain, following an approximation of the actual physical assembly of the mechanism. In order to apply the same principle to both types of mechanisms, an open-loop mechanism was modeled as a closed-loop mechanism by creating a fictitious fixed link in the free space between the base and the end of the chain …

A Silicon Knife Design And Fabrication, Mingli Wang

Theses

In this thesis, the design and fabrication of a silicon knife is described. The device design is based on the principle of oxidation sharpening.

The knife is made from a silicon wafer and can be made to be any chosen length up to 150 mm. It was made with the same basic procedures used in semiconductor chip manufacturing. This type of processing/manufacturing results in a knife with a high degree of sharpness and smoothness compared with existing knife technology.

The knife fabrication plan combines IC processing, techniques including anisotropic and isotropic etching of silicon, plasma dry etching and chemical etching …

Improvement Of Waterjet And Abrasive Waterjet Nozzle, Zheng Li

Dissertations

This investigation is concerned with the improvement of the nozzle design for water and abrasive water jet machining. The mechanism of formation and characteristics of pure water and abrasive water jets are investigated in order to determine quasi-optimal process conditions.

To improve the pure water jet machining, a pulsed water jet nozzle, which employs the principle of the Helmholtz type resonator, is investigated experimentally and numerically. The experiments show the advantages of this nozzle over the commercial nozzle in cutting and cleaning. A numerical solution of the differential equations of continuity, momentum conservation, turbulent kinetic energy and dissipation for two …

Analytical And Simulation Models Of Weaving Area Operations Under Non-Freeway Conditions, Muhammad Shahid Iqbal

Dissertations

The Highway Capacity Manual covers adequately the operation of weaving areas on freeways. Weaving on non-freeway facilities, however, has not been addressed as yet. This research effort presents a state-of-the-art procedural analytical approach and simulation models for the analysis of the level of service and operation of non-freeway weaving areas. Weaving under non-freeway conditions is classified into two broad categories; basic weave and ramp weave. The analytical models for these two weaving categories are calibrated and validated based on data obtained from several sites selected in the states of New Jersey and New York. New level of service criteria are …

Local Thermal Stress Factor Of Pipe-Nozzle, David Chihwei Chen

Dissertations

A comprehensive study of local thermal stresses at the juncture of pipe-nozzle is presented in this thesis. The thermal loading is assumed to be a linear thermal gradient across the thickness of the pipe and nozzle. Currently, there exists neither experimental nor analytical data that is sufficient for pressure vessel designers to analyze the local thermal stresses at the juncture of pipe-nozzle. In order to provide a comprehensive database to calculate these thermal stresses, the finite element technique is used to provide a series of local thermal stress factor plots as a function of pipe-nozzle geometrical parameters.

For the local …

Algorithms In Fault-Tolerant Clos Networks, Hyunyeop Lee

Dissertations

No abstract provided.

Local Stress Factors Of Pipe-Nozzle Under Internal Pressure, Jih-Lian Jack Ha

Dissertations

This thesis presents a comprehensive study of local stresses around a pipe-nozzle due to internal pressure. The finite element method (FEM) was employed to provide a numerical solution which will furnish a database for stress analysts to compute local stresses of pipe-nozzle due to internal pressure. The local pressure stresses for both the pipe and the nozzle around the pipe-nozzle juncture are first normalized into pressure stress factors which are then plotted as functions of geometrical parameters, beta, β, (nozzle mean radius / pipe mean radius) and gamma γ, (pipe mean radius / pipe thickness). These local pressure stresses at …

Characterization Of Sleep Eeg, Seetharamiah Sateesh

Theses

The physiological relationship between the various components of sleep and its variation due to drug administration has been used as one of the primary tools to analyze the performance of drug. A number of studies have been performed in recent years in this direction. Electroencephalogram (EEG) has been characterized with the help of variables ranging from measurements of the duration of different sleep stages to the activities that define the stages themselves. Advances in computer hardware and software have improved the methods of data acquisition and storage. Analysis of long stretch of data has always been a problem considering the …