Engineering Commons^™

Design, Implementation, And Evaluation Of A Shared-Memory Parellel Processing System (Smpps), Eric H. Staub

Theses

As technology reaches its limits of improvements in microprocessor processing speeds, scientists and engineers have to find viable solutions to meet ever-increasing demands for faster processing speed. One such solution is parallel processing. No longer does one have to wait on sequential operations. A specific task can be split in sub-tasks that can run simultaneously, thus reducing the overall execution time of the task.

The design and implementation of these systems is crucial to the effectiveness of parallel systems. A dual-processor SMPPS was designed and implemented in order to demonstrate how multiple processors are a viable solution to increasing the …

Model And Clinical Device Development For Noninvasive Diagnosis Of Low Back Pain And Dysfunction, Ravi Patraju

Theses

Millions of people suffer from acute or chronic low back pain. In order for proper treatment to be administered, a patient must receive an accurate diagnosis. Therefore, it is critical to develop an objective model to measure the motion and any dysfunction of a patient's low back. Only then can a physician effectively implement the correct therapy and measure its effectiveness through follow-up to minimize or eliminate low back pain.

Numerous cadaveric, active and passive studies have been done to understand the mechanics of low back disorders. However, only living human subjects suffer from low back pain and therefore cadaveric …

An Interactive System For The Estimation Of Emissivity Of A Wafer In A Rapid Thermal Processing Chamber, Maurizio Fulco

Theses

Rapid thermal processing (RTP) is a method of thermally processing wafers for the manufacture of integrated circuits. During the thermal processing of wafers, it is essential that the wafer temperature follow a pre-specified temperature trajectory and that the temperature across the wafer be uniform especially at high temperatures. To ensure that the above objectives of RTP temperature control be met at any time during the process, the estimation of some parameters of the process is of fundamental importance in the design of the control system.

This thesis demonstrates the implementation of an interactive software system in which the emissivity of …

Metrics For Estimating The Product Disassembly Effort, Pradeep Kumar Yedlarajaiah

Theses

The concepts of environmentally friendly manufacturing and ecological reuse of materials have resulted in an increase in the number of disposed products that are disassembled. Moreover, the imposition of EPA regulations is forcing companies to invest in methods for protecting the environrnent. The first strategy in this vein is material recycling. The issue of recycling became important because of the limited landfill space, diminishing natural resources, environmental pollution due to dumping of products containing hazardous materials. Likewise, it is projected that the cost of extracting materials from natural resources is going to be much more expensive when compared to reclaiming …

An Investigation Of Polyethylene Bearing Wear Of New Jersey Lcs Knee On Cobalt Chromium And Titanium Nitride Types, Lei Wang

Theses

The total knee replacement systems (TKRS) are used for the treatment of osteoarthritis and rheumatoid arthritis. Excessive wear can substantially shorten their life span.

Two tests were performed to examine the wear characteristics of tibial bearings used in TKRS. Each test consisted of six sets of Anterior/Posterior Glide Tibial Bearings each with a conical control arm. The tibial bearings were all made by UHMWPE. Three of these bearings were mounted onto a Co-Cr alloy tibial platform and Co-Cr alloy LCS® femoral component. Another three sets of bearings were mounted onto a TiN tibial platform and TiN LCS® femoral component. They …

Implementation And Performance Study Of Image Data Hiding/Watermarking Schemes, Arkadiusz Edward Komenda

Theses

Two data hiding / watermarking techniques for grayscale and color images are presented. One of them is DCT based, another uses DFT to embed data. Both methods were implemented in software utilizing C/C++. The complete listings of these programs are included. A comprehensive reliability analysis was performed on both schemes, subjecting watermarked images to JPEG, SPIRT and MPEG-2 compressions. In addition, the pictures were examined by exposing them to common signal processing operations such as image resizing, rotation, histogram equalization and stretching, random, uniform and Gaussian noise addition, brightness and contrast variations, gamma correction, image sharpening and softening, edge enhancement, …

Pneumatic Fracture Propagation And Particulate Transport In Geologic Formations, Suresh Puppala

Dissertations

Pneumatic fracturing is an in situ remediation enhancement technology developed to increase the permeability of contaminated geologic formations. This technology can also be used to deliver atomized liquid and particulate supplements to geologic formations, thereby enhancing in situ processes such as bioremediation and reactive dechlorination.

The main objective of this study was the development of a mathematical model that simulates the propagation of pneumatic fractures in soil and rock formations. Pneumatic fracture propagation differs from other fluid fracturing phenomena in the propagation velocity (1-3 m/sec) and the viscosity of the fracturing fluid (1.9E-05 Pa•sec). For the purposes of model development, …

Automatic Analysis Of Electronic Drawings Using Neural Network, Yi Shi

Dissertations

Neural network technique has been found to be a powerful tool in pattern recognition. It captures associations or discovers regularities with a set of patterns, where the types, number of variables or diversity of the data are very great, the relationships between variables are vaguely understood, or the relationships are difficult to describe adequately with conventional approaches.

In this dissertation, which is related to the research and the system design aiming at recognizing the digital gate symbols and characters in electronic drawings, we have proposed: (1) A modified Kohonen neural network with a shift-invariant capability in pattern recognition; (2) An …

Adaptive Bootstrap Signal Separators For Bpsk/Qam-Modulated Wireless Cdma Systems In A Multipath Environment, Nico J.M. Van Waes

Dissertations

CDMA is an attractive multiple-access scheme, because of its potential capacity increase and its anti-multipath fading capability. For satisfactory performance, however, the effect of the "near-far" problem has to be resolved. This problem can be combated by using power-control, which, however, results in an overall reduction in communication ranges, and thus in a loss of capacity. Among other methods for mitigating the near-far problem is the use of decorrelating receivers, both of fixed type, which directly utilizes the cross-correlation of the users codes, and of adaptive type, which uses recursive algorithms that leads to signal decorrelation. Not to lessen the …

Analysis Of Multi-Lead Qt Dispersion By Means Of An Algorithm Implemented On Labview, Zafer Sahinoglu

Theses

QT dispersion measurement is significant in diagnostic ECG, and several methods are proposed in the literature to implement QT measurement.

This study consists of two parts: The first part was the development of an algorithm to measure both QT interval and QT dispersion. To check the reliability of the algorithm, 25 single channel ECGs were recorded and their QT intervals were computed. On two subjects, three and four lead ECG data were recorded respectively and their QT dispersions were statistically analyzed. Another part of this study dealt with the effect of the electric dipole of the heart on QT dispersion. …

Analysis And Applications Of Ftir Systems, Gunjan Navin Doshi

Theses

Fourier Transform Infrared Spectroscopy (FTIR) is a dynamical instrumental technique used in industry for measuring high quality infrared spectra. Over the last 25 years, the increased demand for having an efficient real-time quantitative measurement technique has led to extensive research and development in the field of FTIR Spectroscopy. Through the use of FTIR, sensitivity has increased, size of the smallest sample that can be analyzed has been reduced, and the number of new applications has exploded. In this thesis, an attempt is made to study the principles, theory, instrumentation and applications of FTIR Spectrometry. We survey the working of spectrometer, …

Reuse Of Cold Top Ex-Situ Vitrified Chromium Contaminated Soils In Hot Mix Asphalt Concrete, Gerald Charleston

Theses

This research investigated the pilot scale feasibility of the remediation of chromium contaminated soil through cold top ex-situ vitrification and the reuse of the vitrified products as highway construction aggregates. There are more than two million tons of chromite ore residues from the chromate extraction manufacturing leftover in Hudson County, New Jersey. They contained both un-leached hexavalent and unoxidized trivalent chromium. Hexavalent chromium is well known as a group A human carcinogen. It is also considered an environmental and health hazard. Of the many ex- situ and in-situ physical, chemical, and biological treatment technologies for chromate production waste, the ability …

Object Oriented 3d Dynamic Simulation Of Flow Of Material Through Hopper, Krishnendu Roy

Theses

Development of object oriented 3D dynamic simulation of the particle is considered. This code is based on the soft sphere model dealing with both normal force , tangential force and the friction. The development of such a model and the code is motivated by the need to understand the flow patterns of granular material. The prime effort while developing this code was focused on the data encapsulation and secured access to all the attributes of all physical parameters of the bulk solid, which might be endangered by the random access of the interface of the software. A dynamically bound array …

The Determination Of 2-Methylisoborneol And Geosmin In Water Using Fluorescence Spectroscopy, Ramesh Chandra Sharma

Theses

Geosmin and 2-Methylisoborneol are responsible for imparting earthy, musty taste and odor qualities to water. The human threshold odor concentrations (TOCs) for 2-MIB and Geosmin vary over a wide range. TOCs of 10ng/1 for Geosmin and 30ng/1 for 2-MIB have been reported.

Currently available methods are time consuming and require use of sophisticated technique and expensive equipment.

Fluorescence spectroscopy has been successfully used in the identification of many organic compounds. Geosmin and 2-MIB have organic origin. This research explores the possibility of using the technique of fluorescence spectroscopy in the determination of Geosmin and 2-MIB. The excitation and emission wavelengths …

Composite Columns, Magnar Berge

Theses

The purpose of this thesis is to provide an introduction in the design of composite columns. The design methods according to AISC and Eurocode 4 are summarized and provide a procedure to design a composite column. In addition, equation are derived to determine the nominal flexural strength of typical composite cross-sections.

Tools For The Design Of Flexible Manufacturind Systems, Prashant A. Patel

Theses

Flexibility in manufacturing systems can broaden the horizons for a company. But the means for achieving it are far more critical. This trend is created by the increase in competitiveness, growth of technology along with demand variations, more customization, and short product life cycles. But "Flexible Manufacturing Systems" to most of the manufacturers sounds like a synonym for automation.

A real Flexible Manufacturing System is designed when every unit of the company is synchronized in such a way to respond in a harmony to any changes that come against it. Fine-tuning of each and every part of the company is …

Nanofiltration With Organic Solvents And Its Possible Applications To Organic Syntheses, Jose Antonio Whu

Theses

Experimental results on the nanofiltration (NF) separation behavior of three different solvent- compatible membranes are presented for three organic solutes of molecular weights 351, 826 and 1355 in methanol; the manufacturer-specified molecular weight cut-offs (MWCO) of the membranes are 250, 400 and 700. Membranes were primarily tested at 440 psig, at different concentrations of the solutes in methanol; the effect of varying the applied pressure was also briefly explored. The solvent permeation flux and the solute rejection were time dependent for an extended initial period; the membranes had to be compacted to achieve steady-state results. Furthermore, the manufacturer-specified MWCO was …

Stabilization Of Water Treatment Plant (Wtp) Residuals Using Sorbond, Rituraj Sinha

Theses

Disposal of water treatment plant (WTP) residuals has always been an important consideration for the water industry. Stringent water quality standards, environmental regulations, and unavailability of land for ultimate disposal affect disposal of large amounts of this residual. The search for alternate economical disposal options and beneficial use are probably the next most logical and economical step to take.

This study was performed to explore the possibility of stabilization of water treatment plant (WTP) residuals using additives. Three water treatment plant (WTP) residuals from treatment plants in New Jersey were used for the analysis. The objective of this research is …

Improving The Run Time Of The Decomposition Algorithm For Fault Tolerant Clos Interconnection Networks Through Swap Re-Ordering, Andrea Laura Mcmakin

Theses

Clos interconnection networks, used in data networks and computing systems, can contain extra switches to be used in faulty conditions. The speed of such fault tolerant Clos interconnection networks is improved through the use these switches in no-fault situations. The network can be represented by a matrix, which is then decomposed using an algorithm, and the switch settings are thus assigned.

The original decomposition algorithm consisted of four element swaps in the following order: wild swap, simple swap, next simple swap, and successive swap. However, by re-arranging these swaps with the simple swap first, followed by the next simple and …

Synthesis And Characterization Of Silicon Dioxide Films Using Diethyl Silane And Oxygen, Kiran Kumar

Theses

This study focuses on producing thin and thick silicon dioxide films towards the fabrication of integrated optical sensor capable of monitoring and determining in-situ, the concentration of numerous analyze species simultaneously. In this study, diethylsilane (DES) has been used as a precursor to produce silicon dioxide films by low pressure chemical vapor deposition. The films were synthesized with two different flow ratios of oxygen to DES in the temperature range of 550°C to 800°C at a constant pressure of 200mTorr. The films deposited with lower oxygen to DES flow ratio have very high growth rate but suffer from high tensile …

Telephone-Accessed Controller Using Cebus For Device Control Over Power Line, Gerald Aska

Theses

The CEBus standard has made it possible for devices developed by different manufacturers to communicate over the power line. Further, the standard allows analog adjustments of devices besides transmitting and receiving binary information. This Controller extends the distance from which these devices can be controlled.

To extend the distance of communication with a device, a telephone line interface was developed that allows the user to communicate with a CEBus device via the Controller. The Controller responses [sic] to Central Office signaling and opens its communication channel to allow the user to provide it with the commands by using the telephone …

Utilizing Gis Technology For Brownfields Redevelopment, Jeffrey J. Duteau

Theses

Typically, when developers, banks and other organizations have an interest in a piece of property they perform an extensive information search to determine if the site is worth purchasing. This search could consist of tax and title information, the location of utilities and major roadways in the area, information on population demographics and environmental contaminant data. An information search of this type could take days, weeks or even months to compile. With a geographic information system (GIS), this search could take a matter of minutes and is displayed in an easy to understand graphic or map form along with a …

Measurement Of The Baroreceptor Sensitivity Index (Brsi) In The Frequency Domains, Tanvir Raquib

Theses

Time domain analysis for calculating the Baroreceptor Sensitivity Index (BRSI) did not always provide an accurate result. It also had another limitation in that it could not show the influence of the autonomic nervous system for different subjects. The correlation coefficient is a mechanism that was used to either accept or reject the BRSI values in the time domain but the correlation coefficient values changed drastically depending on how many sample points were selected for the calculation.

On the other hand, frequency domain analysis for the BRSI calculation was relatively easier and provided more accurate information compared to the time …

Analytical And Experimental Study Of Investment Casting With Laser Stereolithography Models, Wen-Long Yao

Dissertations

This dissertation presents an analytical and experimental investigation of ceramic shell cracking during the burnout process in investment casting with internally webbed laser stereolithography (SLA) patterns. Included in the consideration are the cracking temperature of the ceramic shell, the web link buckling temperature, and the glass transition temperature of the epoxy resin. The hypothesis is that shell cracking will occur when the cracking temperature is lower than the glass transition temperature and the web buckling temperature.

An analytical and experimental study has been conducted, with the cross-sectional area, the span length of the web structure, and the shell thickness being …

A Combined Simulated Annealing And Tabu Search Strategy To Solve Network Design Problem With Two Classes Of Users, Qifeng Zeng

Dissertations

A methodology to solve a transportation network design problem (TCNDP) with two classes of users (passenger cars and trucks) is developed. Given an existing highway system, with a capital investment budget constraint, the methodology selects the best links to be expanded by an extra lane by considering one of three types of traffic operations: exclusive for passenger cars, exclusive for trucks, and for both passenger cars and trucks such that the network total user equilibrium (UE) travel time is minimized.

The problem is formulated as an NP-hard combinatorial nonlinear integer programming problem. The classical branch and bound methodology for the …

Automobile Air Bag Inflation System Using Pressurized Carbon Dioxide, Bart Adams

Dissertations

A novel air bag inflator based on the evaporation ofliquefied carbon dioxide was developed. A detailed qualitative model wasestablished on the basis of an extensive experimental study. An integratedquantitative model of this inflator was constructed.

The system was studied by discharging the inflatorinto a tank and measuring pressure and temperature evolution (0-50 ms). Thedispersion of the two-phase spray duringinflation was investigated by high-speed cinematography.

The optimal storage pressure of the liquid CO₂was found to be 2000 psig (at 22 °C). Two distinct inflator behaviors wereidentified. First, at conditions corresponding to an initial entropy below the critical point, atwo-phase …

Space-Time Reduced Rank Methods And Cfar Signal Detection Algorithms With Applications To Hprf Radar, Tareq F. Ayoub

Dissertations

In radar applications, the statistical properties (covariance matrix) of the interference are typically unknown a priori and are estimated from a dataset with limited sample support. Often, the limited sample support leads to numerically ill-conditioned radar detectors. Under such circumstances, classical interference cancellation methods such as sample matrix inversion (SMI) do not perform satisfactorily. In these cases, innovative reduced-rank space-time adaptive processing (STAP) techniques outperform full-rank techniques. The high pulse repetition frequency (HPRF) radar problem is analyzed and it is shown that it is in the class of adaptive radar with limited sample support. Reduced-rank methods are studied for the …

A Low-Cost High-Speed Twin-Prefetching Dsp-Based Shared-Memory System For Real-Time Image Processing Applications, Charalambos Stephanou Christou

Dissertations

This dissertation introduces, investigates, and evaluates a low-cost high-speed twin-prefetching DSP-based bus-interconnected shared-memory system for real-time image processing applications. The proposed architecture can effectively support 32 DSPs in contrast to a maximum of 4 DSPs supported by existing DSP-based bus- interconnected systems. This significant enhancement is achieved by introducing two small programmable fast memories (Twins) between the processor and the shared bus interconnect. While one memory is transferring data from/to the shared memory, the other is supplying the core processor with data. The elimination of the traditional direct linkage of the shared bus and processor data bus makes feasible the …

Removal Of Volatile Organic Compound (Voc) Vapors In Biotrickling Filters : Process Modeling And Validation With Chlorinated Aromatic Compounds, Christos J. Mpanias

Dissertations

This study dealt with the removal of vapors of volatile organic compounds from airstreams in biotrickling filters (BTFs). A detailed general model was developed for describing the process under steady-state conditions. The model accounts for mass transfer between phases (air, liquid, biofilm) and biodegradation of pollutants in the biofilm. It also accounts for potential kinetic interactions among pollutants as well as potential process limitations by oxygen availability.

The general model was experimentally validated using mono-chlorobenzene (m-CB) and ortho-dichlorobenzene (o-DCB) as model compounds either alone or in mixture with each other. Before BTF experiments were undertaken, a systematic kinetic study was …

Robust Fuzzyclustering For Object Recognition And Classification Of Relational Data, Sumit Sen

Dissertations

Prototype based fuzzy clustering algorithms have unique ability to partition the data while detecting multiple clusters simultaneously. However since real data is often contaminated with noise, the clustering methods need to be made robust to be useful in practice. This dissertation focuses on robust detection of multiple clusters from noisy range images for object recognition. Dave's noise clustering (NC) method has been shown to make prototype-based fuzzy clustering techniques robust. In this work, NC is generalized and the new NC membership is shown to be a product of fuzzy c-means (FCM) membership and robust M-estimator weight (or possibilistic membership). Thus …