Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Missouri University of Science and Technology

Discipline
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 2101 - 2130 of 21777

Full-Text Articles in Engineering

Effect Of Annealing Time On Texture Evolution Of Fe–3.4 Wt% Si Nonoriented Electrical Steel, Yizhou Du, Ronald J. O'Malley, Mario F. Buchely, Paul Kelly Jan 2023

Effect Of Annealing Time On Texture Evolution Of Fe–3.4 Wt% Si Nonoriented Electrical Steel, Yizhou Du, Ronald J. O'Malley, Mario F. Buchely, Paul Kelly

Materials Science and Engineering Faculty Research & Creative Works

Herein, the Effect of Annealing Time on the Texture Evolution in Fe–3.4 Wt.% Si Non-Oriented Electrical Steel is Investigated. Strip Samples Are Cast using a Vacuum Sampling Method, Which Simulate the Solidification Conditions of an Industrial Twin Roll Thin Strip Casting (TRSC) Process. As-Cast Samples with Different Carbon and Sulfur (C&S) Levels Are Hot Rolled (HR) with Varying Levels of Hot Deformation, Cold Rolled (CR) to 0.35 Mm Thickness, and Then Annealed at 1050 °C for Different Holding Times (1, 6, 24 H). to Fe–3.4 Wt.% Si Non oriented Electrical Steel, the Observed Texture Evolution Can Be Divided into Different …

Go to article

Phenomenological Analysis Of Surface Degradation Of Metallic Materials In Extreme Environment, Simon N. Lekakh, Oleg Neroslavsky Jan 2023

Phenomenological Analysis Of Surface Degradation Of Metallic Materials In Extreme Environment, Simon N. Lekakh, Oleg Neroslavsky

Materials Science and Engineering Faculty Research & Creative Works

The resistance to surface degradation in metallic alloys plays an important role for the lifetime of the components working in harsh environments. The mechanisms involved in degradation of metallic surface in a high-temperature aggressive gaseous atmosphere include the following: forming adherent to the surface multiphase oxide layer, partial spallation, and possible vaporization of formed compounds. The governing equation, which describes a parabolic growth of adherent layer, time-dependent vaporization, and cross-linked to instantaneous thickness of adherent layer spallation rate, was suggested and analyzed. The several relationships between the kinetic constants were defined from analysis of the governing equation. Design of routes …

Go to article

Real-Time Air Gap And Thickness Measurement Of Continuous Caster Mold Flux By Extrinsic Fabry-Perot Interferometer, Abhishek Prakash Hungund, Hanok Tekle, Bohong Zhang, Ronald J. O'Malley, Jeffrey D. Smith, Rex E. Gerald, Jie Huang Jan 2023

Real-Time Air Gap And Thickness Measurement Of Continuous Caster Mold Flux By Extrinsic Fabry-Perot Interferometer, Abhishek Prakash Hungund, Hanok Tekle, Bohong Zhang, Ronald J. O'Malley, Jeffrey D. Smith, Rex E. Gerald, Jie Huang

Materials Science and Engineering Faculty Research & Creative Works

Mold Flux plays a critical role in continuous casting of steel. Along with many other functions, the mold flux in the gap between the solidifying steel shell and the mold serves as a medium for controlling heat transfer and as a barrier to prevent shell sticking to the mold. This manuscript introduces a novel method of monitoring the structural features of a mold flux film in real-time in a simulated mold gap. A 3-part stainless-steel mold was designed with a 2 mm, 4 mm and, 6 mm step profile to contain mold flux films of varying thickness. An Extrinsic Fabry-Perot …

Go to article

Modeling Phase Selection And Extended Solubility In Rapid Solidified Alloys, Azeez Akinbo, Yijia Gu Jan 2023

Modeling Phase Selection And Extended Solubility In Rapid Solidified Alloys, Azeez Akinbo, Yijia Gu

Materials Science and Engineering Faculty Research & Creative Works

A new phase selection model based on the time-dependent nucleation theory was developed to investigate the effect of rapid solidification on extended solubility. The model was applied to predict the solubility as a function of undercooling for several binary Al alloys. The predictions of both eutectic and peritectic systems show good agreement with experimental data. It was demonstrated that the developed model is better than the T 0-line method, which neglected the kinetic process of nucleation. Furthermore, the model can also be applied to ternary and multicomponent phases assuming the nucleation is limited by the scarcest species or the slowest …

Go to article

Impact Of Alumina-Based Binder On Formation Of Dense Strontium Zirconate Ceramics, Janos E. Kanyo, R. Sharon Uwanyuze, Jiyao Zhang, Rainer Hebert, Stefan Schafföner, Lesley Frame Jan 2023

Impact Of Alumina-Based Binder On Formation Of Dense Strontium Zirconate Ceramics, Janos E. Kanyo, R. Sharon Uwanyuze, Jiyao Zhang, Rainer Hebert, Stefan Schafföner, Lesley Frame

Materials Science and Engineering Faculty Research & Creative Works

Strontium zirconate (SrZrO3) is a technical ceramic with potential for refractory applications due to its chemical stability at high temperatures, high melting temperature, and favorable thermal expansion coefficient. Practical use of SrZrO3 is limited by poor mechanical strength relative to ceramics such as alumina (Al2O3). Sintering of SrZrO3 with a hydratable Al2O3 binder is investigated as a method for improving mechanical performance. Density, phase composition, thermomechanical properties, and chemical stability in contact with alloys up to 1350 °C are considered. Results are compared with SrZrO3 samples formed using a traditional polyvinyl alcohol (PVA) binder. SrZrO3 reacts with alumina during sintering …

Go to article

Microstructure Evolution And Austenitic Grain Refinement Of Ti-Modified High Mn Steels During Solution Annealing Heat Treatment, Abhinav Karanam, Arnab Sarkar, Erik Nenzen, Viraj Ashok Athavale, Mark Watson, Laura Nicole Bartlett, Lukas Bichler Jan 2023

Microstructure Evolution And Austenitic Grain Refinement Of Ti-Modified High Mn Steels During Solution Annealing Heat Treatment, Abhinav Karanam, Arnab Sarkar, Erik Nenzen, Viraj Ashok Athavale, Mark Watson, Laura Nicole Bartlett, Lukas Bichler

Materials Science and Engineering Faculty Research & Creative Works

Austenitic high manganese (Mn) steels are often used in harsh environments due to their high toughness and wear resistance. Heat treatments are performed to engineer the microstructure of the steels and optimize their performance for the desired service conditions. This study investigated the effect of titanium (Ti) and heat treatment on the microstructure of cast high Mn steel (HMS) alloys. The results reveal that Ti addition contributed to grain refinement in the as cast and heat-treated conditions. In-situ observation of microstructure evolution up to 1125 °C confirmed the stability of precipitated TiC particles, while revealing a new mechanism of grain …

Go to article

Residual Stress Distribution, Distortion, And Crack Initiation In Conventional And Intensive Quench Practices, Kingsley Tochukwu Amatanweze, Mario F. Buchely, Viraj Ashok Athavale, Laura Bartlett, Ronald J. O'Malley, Toshi Suzuki Jan 2023

Residual Stress Distribution, Distortion, And Crack Initiation In Conventional And Intensive Quench Practices, Kingsley Tochukwu Amatanweze, Mario F. Buchely, Viraj Ashok Athavale, Laura Bartlett, Ronald J. O'Malley, Toshi Suzuki

Materials Science and Engineering Faculty Research & Creative Works

This study evaluates the effect of two different quench practices on distortion, sensitivity to quench cracking, development and distribution of residual stress, microstructural uniformity, and hardenability of standardized test castings. Navy C-rings made of AISI 4340 were quenched in this experiment. Some rings were quenched in a conventional draft tube immersion quench bath, and others were quenched in an intensive quench spray system to compare with the results from the conventional immersion quench bath. The rings were measured with a coordinate measuring machine, for distortion and flatness, before and after quenching. Hardness profiles of the quenched rings showed through hardness …

Go to article

A Genome-Wide Association Study Coupled With Machine Learning Approaches To Identify Influential Demographic And Genomic Factors Underlying Parkinson’S Disease, Md Asad Rahman, Jinling Liu Jan 2023

A Genome-Wide Association Study Coupled With Machine Learning Approaches To Identify Influential Demographic And Genomic Factors Underlying Parkinson’S Disease, Md Asad Rahman, Jinling Liu

Engineering Management and Systems Engineering Faculty Research & Creative Works

Background: Despite the recent success of genome-wide association studies (GWAS) in identifying 90 independent risk loci for Parkinson's disease (PD), the genomic underpinning of PD is still largely unknown. At the same time, accurate and reliable predictive models utilizing genomic or demographic features are desired in the clinic for predicting the risk of Parkinson's disease. Methods: To identify influential demographic and genomic factors associated with PD and to further develop predictive models, we utilized demographic data, incorporating 200 variables across 33,473 participants, along with genomic data involving 447,089 SNPs across 8,840 samples, both derived from the Fox Insight online study. …

Go to article

Improving Social Bot Detection Through Aid And Training, Ryan Kenny, Baruch Fischhoff, Alex Davis, Casey I. Canfield Jan 2023

Improving Social Bot Detection Through Aid And Training, Ryan Kenny, Baruch Fischhoff, Alex Davis, Casey I. Canfield

Engineering Management and Systems Engineering Faculty Research & Creative Works

Objective: We test the effects of three aids on individuals' ability to detect social bots among Twitter personas: a bot indicator score, a training video, and a warning. Background: Detecting social bots can prevent online deception. We use a simulated social media task to evaluate three aids. Method: Lay participants judged whether each of 60 Twitter personas was a human or social bot in a simulated online environment, using agreement between three machine learning algorithms to estimate the probability of each persona being a bot. Experiment 1 compared a control group and two intervention groups, one provided a bot indicator …

Go to article

Additive Manufacturing Of Sic-Sialon Refractory With Excellent Properties By Direct Ink Writing, Ruoyu Chen, Saisai Li, Xinxin Jin, Haiming Wen Jan 2023

Additive Manufacturing Of Sic-Sialon Refractory With Excellent Properties By Direct Ink Writing, Ruoyu Chen, Saisai Li, Xinxin Jin, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Additive manufacturing of SiC-Sialon refractory with complex geometries was achieved using direct ink writing processes, followed by pressure less sintering under nitrogen. The effects of particle size of SiC powders, solid content of slurries and additives on the rheology, thixotropy and viscoelasticity of ceramic slurries were investigated. The optimal slurry with a high solid content was composed of 81 wt% SiC (3.5 µm+0.65 µm), Al2O3 and SiO2 powders, 0.2 wt% dispersant, and 2.8 wt% binder. Furthermore, the accuracy of the structure of specimens was improved via adjustment of the printing parameters, including nozzle size, extrusion pressure, and layer height. The …

Go to article

Reduction Of Iron-Ore Pellets Using Different Gas Mixtures And Temperatures, Yuri Korobeinikov, Amogh Meshram, Christopher Harris, Olexandr Kovtun, Joe Govro, Ronald J. O'Malley, Olena Volkova, Seetharaman Sridhar Jan 2023

Reduction Of Iron-Ore Pellets Using Different Gas Mixtures And Temperatures, Yuri Korobeinikov, Amogh Meshram, Christopher Harris, Olexandr Kovtun, Joe Govro, Ronald J. O'Malley, Olena Volkova, Seetharaman Sridhar

Materials Science and Engineering Faculty Research & Creative Works

Direct reduction of iron ore (DRI) is gaining an increased attention due to the growing need to decarbonize industrial processes. The current industrial DRI processes are performed using reformed natural gas, which results in CO2 emission, although it is less than carbothermic reduction in the blast furnace. Carbon-free reduction may be realized through the utilization of green H2 as a reducing agent, in place of natural gas. Herein, the effects of various gas mixtures and temperature on the reduction kinetics of the hematite iron-ore pellets are focused on in this work. Pellets are reduced at 700, 800, 850, …

Go to article

Additive Manufacturing Of (Mgconicuzn)O High-Entropy Oxide Using A 3d Extrusion Technique And Oxide Precursors, Ruoyu Chen, Saisai Li, Qingfeng Yan, Haiming Wen Jan 2023

Additive Manufacturing Of (Mgconicuzn)O High-Entropy Oxide Using A 3d Extrusion Technique And Oxide Precursors, Ruoyu Chen, Saisai Li, Qingfeng Yan, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

This report presents an additive manufacturing approach, for the first time, to producing high-entropy oxides (HEOs) using a 3D extrusion-based technique with oxide precursors. The precursors were prepared by a wet chemical method from sulfates. Additives were utilized to optimize the rheological properties of the printing inks with these precursors, and the properties of the printed HEOs were improved by increasing the solid content of the inks. When ink with a solid content of 78 wt% was used for printing, the resulting HEO exhibited a relative density of 92% and a high dielectric constant after undergoing pressure less sintering at …

Go to article

The Effect Of Crystal Anisotropy On Fracture Toughness And Strength Of Zrb2 Microcantilevers, Tamás Csanádi, Ahmad Azizpour, Marek Vojtko, William Fahrenholtz Jan 2023

The Effect Of Crystal Anisotropy On Fracture Toughness And Strength Of Zrb2 Microcantilevers, Tamás Csanádi, Ahmad Azizpour, Marek Vojtko, William Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

The influence of crystal anisotropy on the micromechanical properties of ceramic grains plays an important role in the design of the macromechanical performance of bulk polycrystalline samples. To this end, the effect of crystal orientation on fracture toughness and strength was investigated by microcantilever bending experiments combined with finite element method (FEM) simulations in grains of a polycrystalline ZrB2 sample. The sample was prepared by hot pressing and the crystal orientations were determined by electron backscatter diffraction after careful surface preparation. The bending tests were carried out on notched and unnotched microcantilevers cut from specific grains along the prismatic (⊥ …

Go to article

In Situ And Real-Time Mold Flux Analysis Using A High-Temperature Fiber-Optic Raman Sensor For Steel Manufacturing Applications, Bohong Zhang, Hanok Tekle, Ronald J. O'Malley, Todd Sander, Jeffrey D. Smith, Rex E. Gerald, Jie Huang Jan 2023

In Situ And Real-Time Mold Flux Analysis Using A High-Temperature Fiber-Optic Raman Sensor For Steel Manufacturing Applications, Bohong Zhang, Hanok Tekle, Ronald J. O'Malley, Todd Sander, Jeffrey D. Smith, Rex E. Gerald, Jie Huang

Materials Science and Engineering Faculty Research & Creative Works

Continuous Casting in Steel Production Uses Specially Developed Oxyfluoride Glasses (Mold Fluxes) to Lubricate a Mold and Control the Solidification of the Steel in the Mold. the Composition of the Flux Impacts Properties, Including Basicity, Viscosity, and Crystallization Rate, All of Which Affect the Stability of the Casting Process and the Quality of the Solidified Steel. However, Mold Fluxes Interact with Steel during the Casting Process, Resulting in Flux Chemistry Changes that Must Be Considered in the Flux Design. Currently, the Chemical Composition of Mold Flux Must Be Determined by Extracting Flux Samples from the Mold during Casting and Then …

Go to article

In Situ High-Temperature Raman Spectroscopy Via A Remote Fiber-Optic Raman Probe, Bohong Zhang, Hanok Tekle, Ronald J. O'Malley, Jeffrey D. Smith, Rex E. Gerald, Jie Huang Jan 2023

In Situ High-Temperature Raman Spectroscopy Via A Remote Fiber-Optic Raman Probe, Bohong Zhang, Hanok Tekle, Ronald J. O'Malley, Jeffrey D. Smith, Rex E. Gerald, Jie Huang

Materials Science and Engineering Faculty Research & Creative Works

This Study Demonstrated for the First Time an in Situ High-Temperature Fiber-Optic Raman Probe to Study the Structure of Glass and Slag Samples at Temperatures Up to 1400 °C. a Customized External Telescope Was Integrated into a Portable Fiber-Optic Raman Probe to Extend the Optical Working Distance to Allow the Probe to Work in a High-Temperature Environment. Three Samples Were Evaluated to Demonstrate the Functionality of the High-Temperature Fiber-Optic Raman Probe. Room Temperature and High-Temperature Raman Spectra Were Successfully Collected and Analyzed. in Addition, a Deconvolution Algorithm Was Used to Identify Peaks in the Spectrum that Could Then Be Related …

Go to article

Compositional Modifications To Alter And Suppress Laves Phases In Alxcrmotayti Alloys, Austin E. Mann, Joseph William Newkirk Jan 2023

Compositional Modifications To Alter And Suppress Laves Phases In Alxcrmotayti Alloys, Austin E. Mann, Joseph William Newkirk

Materials Science and Engineering Faculty Research & Creative Works

Herein, the Development of Refractory Complex Concentrated Alloys in the Al–Cr–Mo–Ta–Ti Alloy System is Reported. Alloys with Modified Al and Ta Concentrations Are Designed using CALPHAD Tools and Produced Via Arc Melting and Characterized in Both As-Cast and Annealed Forms. Properties of the Alloys, Nature of the Microstructures, and Phase Transformation Behavior Are Described Via X-Ray Diffraction, Microstructural Characterization, Microhardness, and Differential Scanning Calorimetry. Two Alloys, Namely, Al0.25CrMoTa0.8Ti and Al0.75CrMoTa0.8Ti, Are Represented by a Body-Centered-Cubic Matrix Phase after Annealing, along with a Secondary Cr–Ta Laves Phase of the C15 and C14 Polytypes, respectively. in As-Cast and Annealed Forms, the Al0.75CrMoTa0.45Ti …

Go to article

High Temperature Dielectric Properties Of Calcium Zirconate, Alan Devoe, Hung Trinh, Fatih Dogan Jan 2023

High Temperature Dielectric Properties Of Calcium Zirconate, Alan Devoe, Hung Trinh, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

The electrical properties of dense, high purity CaZrO3 discs, sintered at 1380°C with and without added ZrO2, were investigated up to 950°C. Dielectric constant, loss tangent, and electrical conductivity were measured from 25 to 725°C, and the real and imaginary impedances were measured between 800 and 950°C by impedance spectroscopy techniques. Dielectric constant increased by 8% above 300°C and loss tangent increased from.1% at 25°C to ∼2% above 300°C. Activation energy of electrical conductivity determined between 300°C and 950°C by alternative current (AC) and direct current (DC) measurements. These results indicate that CaZrO3 could be a useful dielectric material for …

Go to article

Oxidation Behavior Of Nb-Coated Zirconium Diboride, Jan E. Förster, William Fahrenholtz, Gregory E. Hilmas, Ravisankar Naraparaju Jan 2023

Oxidation Behavior Of Nb-Coated Zirconium Diboride, Jan E. Förster, William Fahrenholtz, Gregory E. Hilmas, Ravisankar Naraparaju

Materials Science and Engineering Faculty Research & Creative Works

Metallic Nb-Coatings Were Deposited on Top of ZrB2 by Means of Magnetron Sputtering to Improve its Oxidation Resistance. High Temperature Oxidation Tests Have Revealed that the Metallic Nb-Coatings Lead to the Formation of a Dense Solid and Protective Reaction Zone in Addition to a More Stable B2O3 Liquid Solution at the Surface. Compared to Baseline ZrB2, a Reduction in the Oxidation Kinetics, as Well as the Thickness of the Porous Zirconia Layer by 71%, Has Been Achieved with the Help of Nb-Coatings. a Liquid Phase Sintering by Molten Nb2O5 Mechanism Was …

Go to article

High Temperature Confocal Scanning Laser Microscopy Analysis Of Dead-Burned Magnesia Aggregates, Tyler Richards, Viraj Athavale, Jeffrey D. Smith, Ronald J. O'Malley Jan 2023

High Temperature Confocal Scanning Laser Microscopy Analysis Of Dead-Burned Magnesia Aggregates, Tyler Richards, Viraj Athavale, Jeffrey D. Smith, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Dead-Burned Magnesia is a Commonly Used Material in the Manufacturing of Refractories for the Steelmaking Industry. Aggregates of Dead-Burned Magnesia Contain Secondary Phases Due to the Impurities within the Magnesite Rock Used in its Production. While These Phases Can Aid in Sintering Magnesia, They May Have Some Impact on the High-Temperature Performance of the Refractory Product. High-Temperature Confocal Scanning Laser Microscopy Was Utilized to Observe the Behavior of Dead-Burned Magnesia Aggregates at Elevated Temperatures (Up to 1550°C). Liquid Formation Was Detected Even at Temperatures Below 1350°C. in Some Cases, This Liquid Quickly Exuded from the Aggregate Surface. This Liquid Phase …

Go to article

Intragranular Nanocomposite Powders As Building Blocks For Ceramic Nanocomposites, Ryan D. Dempsey, Xiaoqing He, Jonathan A. Scott, David W. Lipke Jan 2023

Intragranular Nanocomposite Powders As Building Blocks For Ceramic Nanocomposites, Ryan D. Dempsey, Xiaoqing He, Jonathan A. Scott, David W. Lipke

Materials Science and Engineering Faculty Research & Creative Works

A powder-based bottom-up processing scheme is introduced for the production of ceramic nanocomposites. Internal displacement reactions between solid solution powders and metallic reactants proceeding via gaseous intermediates are utilized to generate nanostructured building blocks for the synthesis of ceramic nanocomposites. Subsequent rapid sintering results in ceramic nanocomposites, whose microstructures are inherited from the building blocks. This processing scheme is demonstrated for the production of titanium carbide nanocomposites featuring up to 28 wt.% intragranular tungsten inclusions derived from titanium-tungsten mixed carbide powders. Heat treatment of mixed carbide powders in evacuated ampoules containing titanium sponge and iodine at 1000°C for 24 h …

Go to article

Thermal And Electrical Properties Of Spark Plasma Sintered (Ti,Cr)B2 Ceramics, Steven M. Smith, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Laura Silvestroni Jan 2023

Thermal And Electrical Properties Of Spark Plasma Sintered (Ti,Cr)B2 Ceramics, Steven M. Smith, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Laura Silvestroni

Materials Science and Engineering Faculty Research & Creative Works

Thermal and electrical properties were measured for TiB2 ceramics containing varying CrB2 contents up to 33 mol%. The room-temperature thermal diffusivity decreased with increasing Cr content from 0.330 ± 0.003 cm2/s for pure TiB2 to 0.060 ± 0.003 cm2/s for (Ti0.66Cr0.33)B2. The amount of anisotropy in the coefficients of thermal expansion increased with increasing Cr content and the c-axis had the greatest dependence on Cr addition, with an increase of more than 25% in the thermal expansion for 33 mol% CrB2 compared to TiB2, whereas the a-axis only increased by about 8%. The electrical conductivity was the lowest for (Ti0.66Cr0.33)B2 …

Go to article

Characterization Of Virgin, Re-Used, And Oxygen-Reduced Copper Powders Processed By The Plasma Spheroidization Process, M. Hossein Sehhat, David Perez-Palomino, Connor Wiedemeier, Tristan Cullom, Joseph William Newkirk Jan 2023

Characterization Of Virgin, Re-Used, And Oxygen-Reduced Copper Powders Processed By The Plasma Spheroidization Process, M. Hossein Sehhat, David Perez-Palomino, Connor Wiedemeier, Tristan Cullom, Joseph William Newkirk

Materials Science and Engineering Faculty Research & Creative Works

Fabrication of parts with high mechanical properties heavily depend on the quality of powder deployed in the fabrication process. Copper powder in three different powder types were spheroidized using radio-frequency inductively coupled plasma (ICP) spheroidization process (TekSphero-15 system). The characterized powders include virgin powder as purchased from the powder manufacturer, powder used in electron beam powder bed fusion (EB-PBF) process, and reconditioned powder, which was used powder that underwent an oxygen-reduction treatment. The goal of spheroidizing these powder types was to evaluate the change in powder morphology, the possibility of enhancing the powder properties back to their as-received conditions, and …

Go to article

Boro/Carbothermal Reduction Co-Synthesis Of Dual-Phase High-Entropy Boride-Carbide Ceramics, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Stefano Curtarolo Jan 2023

Boro/Carbothermal Reduction Co-Synthesis Of Dual-Phase High-Entropy Boride-Carbide Ceramics, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Stefano Curtarolo

Materials Science and Engineering Faculty Research & Creative Works

Dense, dual-phase (Cr,Hf,Nb,Ta,Ti,Zr)B2-(Cr,Hf,Nb,Ta,Ti,Zr)C ceramics were synthesized by boro/carbothermal reduction of oxides and densified by spark plasma sintering. The high-entropy carbide content was about 14.5 wt%. Grain growth was suppressed by the pinning effect of the two-phase ceramic, which resulted in average grain sizes of 2.7 ± 1.3 µm for the high-entropy boride phase and 1.6 ± 0.7 µm for the high-entropy carbide phase. Vickers hardness values increased from 25.2 ± 1.1 GPa for an indentation load of 9.81 N to 38.9 ± 2.5 GPa for an indentation load of 0.49 N due to the indentation size effect. Boro/carbothermal …

Go to article

Thermal And Electrical Properties Of Spark Plasma Sintered (Ti,Cr)B2 Ceramics, Steven M. Smith, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Laura Silvestroni Jan 2023

Thermal And Electrical Properties Of Spark Plasma Sintered (Ti,Cr)B2 Ceramics, Steven M. Smith, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Laura Silvestroni

Materials Science and Engineering Faculty Research & Creative Works

Thermal and electrical properties were measured for TiB2 ceramics containing varying CrB2 contents up to 33 mol%. The room-temperature thermal diffusivity decreased with increasing Cr content from 0.330 ± 0.003 cm2/s for pure TiB2 to 0.060 ± 0.003 cm2/s for (Ti0.66Cr0.33)B2. The amount of anisotropy in the coefficients of thermal expansion increased with increasing Cr content and the c-axis had the greatest dependence on Cr addition, with an increase of more than 25% in the thermal expansion for 33 mol% CrB2 compared to TiB2, whereas the …

Go to article

Characterization Of Virgin, Re-Used, And Oxygen-Reduced Copper Powders Processed By The Plasma Spheroidization Process, M. Hossein Sehhat, David Perez-Palomino, Connor Wiedemeier, Tristan Cullom, Joseph William Newkirk Jan 2023

Characterization Of Virgin, Re-Used, And Oxygen-Reduced Copper Powders Processed By The Plasma Spheroidization Process, M. Hossein Sehhat, David Perez-Palomino, Connor Wiedemeier, Tristan Cullom, Joseph William Newkirk

Materials Science and Engineering Faculty Research & Creative Works

Fabrication of parts with high mechanical properties heavily depend on the quality of powder deployed in the fabrication process. Copper powder in three different powder types were spheroidized using radio-frequency inductively coupled plasma (ICP) spheroidization process (TekSphero-15 system). The characterized powders include virgin powder as purchased from the powder manufacturer, powder used in electron beam powder bed fusion (EB-PBF) process, and reconditioned powder, which was used powder that underwent an oxygen-reduction treatment. The goal of spheroidizing these powder types was to evaluate the change in powder morphology, the possibility of enhancing the powder properties back to their as-received conditions, and …

Go to article

Microstructure And Residual Stress In Functionally Graded 316l Stainless Steel/Inconel 625 Alloys Fabricated By Direct Energy Deposition, Xinchang Zhang, Liang Wang, Frank W. Liou, Yang Ren, Cheng Sun Jan 2023

Microstructure And Residual Stress In Functionally Graded 316l Stainless Steel/Inconel 625 Alloys Fabricated By Direct Energy Deposition, Xinchang Zhang, Liang Wang, Frank W. Liou, Yang Ren, Cheng Sun

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Functionally graded materials (FGMs) provide a unique solution to combine distinct properties within a single component to enhance its overall performance. Understanding the microstructure and residual stress distribution is particularly important as the material dissimilarity in FGMs can result in high residual stress that affects the mechanical integrity of structural components. This work aims to study the microstructure and residual stress of additively manufactured FGMs and the effects of isothermal annealing. In this study, 316L stainless steel/Inconel 625 FGMs were built by direct energy deposition and characterized by optical and electron microscopy as well as synchrotron-based X-ray diffraction. Our study …

Go to article

Charging Of Irregularly-Shaped Dust Grains Near Surfaces In Space, David Lund, Xiaoming He, Daoru Han Jan 2023

Charging Of Irregularly-Shaped Dust Grains Near Surfaces In Space, David Lund, Xiaoming He, Daoru Han

Mathematics and Statistics Faculty Research & Creative Works

This paper presents fully kinetic numerical investigation of the charging of dust grains in low temperature collision less plasmas (stationary) and collision less, cold-ion thermal-electron drifting plasmas. the Parallel Immersed-Finite-Element Particle-in-Cell (PIFE-PIC) code is utilized to self-consistently resolve the plasma environment and charging of immersed materials. This model explicitly includes the materials property (dielectric constant) of dust grains. Effects of materials property, inter-dust distance, and plasma conditions (stationery and drifting) will be investigated for both single-dust and multi-dust configurations.

Go to article

A Data-Driven Approach To Multiresolution Analysis Of Near-Field Scanning, Yanming Zhang, Lijun Jiang Jan 2023

A Data-Driven Approach To Multiresolution Analysis Of Near-Field Scanning, Yanming Zhang, Lijun Jiang

Electrical and Computer Engineering Faculty Research & Creative Works

Near-field scanning has been widely adopted as a valuable tool in diagnosing electromagnetic compatibility (EMC) and electromagnetic interference (EMI) problems. This paper proposes a multiresolution dynamic mode decomposition (MRDMD)-based method for analyzing time-varying near-field radiation. MRDMD executes the traditional DMD method recursively and hierarchically. The distribution of DMD eigenvalues determines the slow and fast modes in a level's decomposition, in which the slow modes are reserved, and the fast modes are utilized to generate the input data for the next level. Finally, the multiresolution time-frequency representation of the near-field radiation field is obtained. And the spatial distributions corresponding to each …

Go to article

Interval Analysis Method For The Uncertainty And Sensitivity Characterization In Transmission Line Systems, Ping Yuan, Lijun Jiang Jan 2023

Interval Analysis Method For The Uncertainty And Sensitivity Characterization In Transmission Line Systems, Ping Yuan, Lijun Jiang

Electrical and Computer Engineering Faculty Research & Creative Works

Uncertainty in electronic fabrication process could cause serious yield issues and stability concerns. Hence, identifying the resultant range caused by the uncertainty in the system is a critical topic in modern EDA design process. Monte Carlo method is considered as a golden standard but with many drawbacks. In the paper, we propose to use the interval analysis (IA) to analyze the signal integrity and power integrity problems in transmission line (TL) systems. Using the interval representing the uncertainty range of parameters in the system, the uncertainty range of the system can be derived by the derived analytical expression. It is …

Go to article

Nanobubble-Induced Aggregation Of Ultrafine Particles: A Molecular Dynamics Study, Eric Bird, Zhi Liang Jan 2023

Nanobubble-Induced Aggregation Of Ultrafine Particles: A Molecular Dynamics Study, Eric Bird, Zhi Liang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Nanobubble-induced aggregation (NBIA) of fine and ultrafine particles in liquid is a promising method for enhancing floatation rates in mineral processing, cleaning contaminants from water, and reviving marine ecosystems. Although the current experimental techniques can measure the nanobubble capillary force between two surfaces with controlled approach speed, they are not capable of imaging NBIA dynamics of fine/ultrafine particles by real-time observation with nanoscale spatial resolution. In this work, we use molecular dynamics (MD) simulations to study dynamics of NBIA of Ag particles in a Lennard-Jones fluid system. The molecular-level modeling allows us to study microscopic details of NBIA dynamics that …

Go to article

First Prev Next Last