Engineering Commons^™

Anodic Dissolution Of Silver In Aqueous Solutions, Jagdish Shantilal Sanghvi

Masters Theses

"Silver and platinum, although not used extensively in industry, find considerable use in specialized work. Silver, because of its much lower cost, is used to a greater extent than platinum. Since silver has a high position in the electromotive series, it is very resistant to chemical attack. It is unaffected by alkaline conditions even at high temperatures and hence silver is used in ladles and molds for producing pure sodium and potassium hydroxides. This and its excellent electrical conductivity makes it a very useful material in circuitry.

It has been reported in the literature that when active metals such as …

Kinetics Of Base-Catalysed Reactions, Kunjvihari Ramanlal Mehta

Masters Theses

"The work of Wulfman on the mechanism of the Michael reactions suggests that the normal Michael reaction is second order kinetically, with the rate being proportional to the concentration of the acceptor and the active form of the addendum. A detailed reaction mechanism of normal Michael reaction was not proposed due to insufficient data which resulted from analytical difficulties. This investigation involves the study of the kinetics of normal Michael reaction from the stand point of base strength, solvent concentration and acidity of the reactants, solvent and products"--Experimental. A. Purpose of Investigation, page 17.

Matching Of A Horn Antenna To Its Dense Surrounding Media By The Use Of Artificial Dielectric Methods, Paul Arthur Ray

Masters Theses

"The purpose of this thesis is to design an artificial dielectric slug to match a horn in a media such as water and to discuss a method of determining experimentally its dielectric properties. The design is based on known artificial dielectric methods. The method of determining the dielectric properties is by microwave waveguide reflection techniques. This thesis deals with the theoretical aspects and suggests an experimental method of determining the practicability of such a matching method"--Abstract, page ii.

Infinite Beams On An Elastic Foundation, Shi-Peing Chang

Masters Theses

"In this paper a partial differential equation for the analysis of beams resting on an elastic foundation under dynamic load is presented. A solution for this equation is derived, and solutions for various boundary conditions of infinite beams resting on an elastic foundation are discussed. The application of the equation is demonstrated by an example of a moving load traveling along an infinite beam"--Abstract, page ii.

The Effect Of Small Alloy Additions On The Quench Induced Texture Of Alpha Uranium, Kenneth Ray Riggs

Masters Theses

"The preferential orientations produced in binary alloys of U-Si and U-Cr on plane sections perpendicular to the direction of heat flow by cooling from beta-phase temperatures were determined. The experimentally determined textures were presented using inverse pole figures. A definite and reproducible relationship was found to exist between the preferred orientation present at any position and the cooling rate which material at the position had experienced. It was found that the concentration of the alloying elements within the ranges studied had little detectable effect upon the observed relationship between the cooling rate and the resulting preferential orientation. It was postulated …

Effects Of Internal Pressure Upon The Buckling Of Thin Circular Cylindrical Shells Under Axial Compression, Leroy E. Thompson

Masters Theses

"An experimental investigation was made of the effects of internal pressure upon the buckling of thin circular cylindrical shells under axial compression. A comparison was made of the experimental and theoretical results; the latter were derived from the large-deflection theory. Results showed that the internal pressure had an appreciable strengthening effect upon the buckling of the cylindrical shell. The comparison showed that the experimental results were lower than the theoretical results for a given internal pressure. The discrepancy between the results can be expected since there were factors not included in the theory: imperfections, end conditions, lengths, and material irregularities"--Abstract, …

A Photoelastic Study Of The Effect Of Certain Geometric Variables On The Plane Stress Distribution In An Electrical Insulator Body, Richard L. Pendleton

Masters Theses

"Photoelastic models were used to indicate stress patterns in various geometrically designed shapes. Each model represented a two-dimensional cross-section of the interior portion of an axially symmetrical porcelain electrical insulator. Five different loading pins were combined with three loading heads to produce eleven models. The maximum stress in each model was determined using a photoelastic method of stress analysis. An attempt was made to select the best structural design to be used in an electrical insulator. The test results indicate that the most desirable stress distribution is obtained using a single step loading pin and that the loading head angle …

Field Permeability Determination Of Partially Saturated Fine Grained Soil, Edward G. Rapp

Masters Theses

"The determination of water permeability through a soil is necessary to estimate seepage losses from small reservoirs. At the present time, the methods available to conduct this determination in partially saturated fine grained soils are expensive and in most cases not commensurate with the cost or importance of the individual structure. This investigation was conducted to evaluate the use of a proposed, potentially inexpensive field procedure in this situation. A modified borehole apparatus was utilized in field tests to determine the permeability of a partially saturated soil deposit in place. Undisturbed samples from the same location were tested in the …

Equivalent Circuit Of Unsymmetrical Inductance Diode Using Linvill Lumped Model, Donald Lawrence Willyard

Masters Theses

"Integrated circuit techniques and applications are rapidly changing the electronics industry. A problem common to both state-of-the-art approaches to integrated circuit fabrication is that of miniaturizing and integrating inductors. It is found that, for a certain range of injection current levels, certain unsymmetrically doped junction diodes have an inductive small-signal impedance. This thesis discusses the theory of inductance diodes and applies finite difference equations and the Linvill lumped model to the differential equations that describe their carrier flow processes. The static I-V characteristic and the small-signal equivalent circuit at high injection densities are derived. The elements (R,L,C) of this equivalent …

Design Of Non-Uniform Linear Antenna Arrays With Digitized Spacing And Amplitude Levels, Jack F. Morris

Masters Theses

"Recent developments in space exploration have shown a need for high resolution, high gain antennas. The introduction of non-uniform linear array theory has provided a means by which arrays may be designed to produce narrow main beams with fewer elements than required by uniform arrays. A general theory has not been developed, however, and the design engineer has been left with only trial-and-error methods with which to work. In this study a technique has been developed by which non-uniform antenna arrays may be synthesized to meet a given set of specifications with reasonable accuracy. The elements of the array are …

An Investigation Of Continuous Prestressed Concrete Structures, Ping-Chi Mao

Masters Theses

"This thesis presents an analysis of the behavior of continuous prestressed concrete structures. From this analysis the governing equations for various types of geometry for prestressing cables are derived. The calculation of fixed-end moments due to the prestressing force using the equations derived is quite cumbersome, however, in order to simplify the calculations, design charts are developed. A cable with reverse curvature is analyzed using the design charts. It is shown that the fixed-end moments calculated by neglecting the effect of reverse curvature differ significantly from the fixed-end moments calculated by considering this effect. Hence the effect of reverse curvature …

Permeability And Additive Absorption And Extraction In Lubricating Greases, Eugene Hsiung-Jen Tu

Masters Theses

"A permeability apparatus was used to measure the permeability coefficients of eight Lithium-Calcium greases and ten Baragel greases in which the viscosity and type of the oil component were varied. The oil present in each grease was used for its permeability measurement.

An improved sample packing technique was developed to improve the repeatability of permeability measurements. Repeatability of ± 3% was achieved. In general the permeability coefficients of the non-soap Baragel greases were higher than those of the lithium-calcium greases with comparable oil components, and those of greases containing paraffinic oils were higher than these containing naphthenic oils. The effect …

Epoxy Resin Admixture For Concrete, Kuo-Chu Hu

Masters Theses

"This thesis describes laboratory tests on concrete having epoxy as an admixture. Cylinders for compression and elastic modulus tests were cured under two different curing conditions, standard laboratory cure and a simulated job cure. Beams cured under laboratory conditions were tested for flexural strength. Test results show the compressive strength increases with an increase of epoxy content for job curing conditions. However, compressive and flexural strengths of specimens cured under laboratory conditions show a slight decrease. The elastic modulus of concrete containing epoxy also decreases in comparison to ordinary concrete"--Abstract, page ii.

The Prediction Of Mix Design Properties For Dense Graded Bituminous Mixtures, Robert Ernest Weeks

Masters Theses

"The purpose of this investigation was to ascertain the feasibility of interpolating values of the physical properties of a dense graded bituminous mix between known values. Also the effects of limestone mineral filler on the properties of a dense graded mix are evaluated. The variables in this study were mineral filler and asphalt cement. Control mixes were established at 2, 6 and 10 percent mineral filler and experimental mixes were prepared at 4 and 8 percent filler. The aggregate consisted of limestone and was mixed with an asphalt cement of 85-100 grade penetration. Al mixes were tested by the Marshall …

Effect Of Single Stirrups On Reinforced Concrete Beams, Vinodbhai T. Patel

Masters Theses

"This study was made to determine the location of vertical stirrups and also to determine the amount of stirrup-steel required to prevent diagonal cracking. The study is limited to rectangular, simply supported, reinforced concrete beams subjected to a concentrated point load at the center of the span. Five sets, each containing three beams were tested. Two sets were cast without stirrups and the results were used to locate the stirrups for the remaining tests. The other three sets were cast with one stirrup on either side of the central load. Stirrups were of the "U" type and formed form No. …

The Design And Construction Of An Instrument For Calibrating Accelerometers, Richard Rabenau

Masters Theses

"The purpose of this work was to design and construct a facility to calibrate accelerometers. A ceramic piezoelectric shaker and modified Michelson interferometer together with necessary electronic equipment were used. The system produced accurate and stable acceleration at five discrete points from 1,000 to 5,000 cycles per second. the maximum calibration levels were approximately 50 g's"--Abstract, page ii.

A Circularly Polarized Corner Reflector Antenna, Walter Ronald Koenig

Masters Theses

"Image theory is used to develop the far field and polarization equations for a ninety degree corner reflector antenna. These equations are in terms of spherical coordinates, the length of the dipole element, the distance of the dipole from the corner of the reflector, and the angle of tilt of the dipole element with the apex of the corner. The equations are simplified to give the far fields in the vertical and horizontal planes for the special case of a half-wavelength dipole. An expression to calculate the distance of the dipole from the corner necessary to give circular polarization broadside …

Construction Of A Capillary Viscometer And The Study Of Non-Newtonian Liquids, Hsun Kuang Yang

Masters Theses

"A capillary tube viscometer was built for the purpose of investigating the fluid properties of non-Newtonian aqueous CMC and Carbopol solutions. The viscometer was tested with Newtonian liquids (glycerine, water and two different oils) having known viscosities to insure that the viscometer was operating correctly. The shear stress-shear rate data obtained for different concentrations of CMC and Carbopol solutions were correlated using the simple power law model. The power law constants were only slightly affected by saturating the solution with iodine and carbon tetrachloride. Aging had very little effect on the viscosities of the CMC solutions but had a considerable …

The Thermodynamics Of The Zno-Fe₂O₃-Fe₃O₄ System, Robert Lee Benner

Doctoral Dissertations

"The purpose of this investigation was to (1) experimentally locate certain phase boundaries in three isothermal sections of the zinc oxide - ferric oxide - magnetite phase diagram, (2) to experimentally determine some of the thermodynamic properties of the zinc oxide - ferric oxide - magnetite system, (3) to use the thermodynamic properties of the zinc oxide - ferric oxide - magnetite system to evaluate the pseudo-binary system between zinc ferrite and magnetite, (4) to construct a compound stability diagram for the zinc-iron-oxygen-sulfer system"--Introduction, Statement of the Problem, page [1].

Drag Reduction In Newtonian Polymer Solutions, Harry C. Hershey

Doctoral Dissertations

"Prior work in the area of drag reduction has been mainly limited to aqueous solutions. Theoretical and empirical analyses of the resulting data in aqueous solutions have been hindered by the fact that some polymers cause drag reduction and others do not...This investigation was directed to the study of how the size and configuration of the polymer molecule in solution affected drag reduction and the related phenomenon of turbulence suppression. Apparatuses were designed and built to measure viscometric flow, curves, friction factors, velocity profiles, and normal stresses (by a jet thrust technique developed by Metzner and associates)"--Summary, page 1-2.

Internal Friction Of Mixed-Alkali Silicate Glasses, James E. Shelby

Doctoral Dissertations

"The mixed alkali effect in silicate glasses was examined from internal friction measurements made over the temperature range from -190 to 500⁰C and at a frequency of 0.4 Hz. Supplemental measurements of the activation energy for the different internal friction peaks, dynamic shear modulus, density, and index of refraction were also made. All measurements were confined to silicate glasses containing mixtures of Li-Na, Li-K, Li-Rb, Li-Cs, Na-K, Na-Rb, Na-Cs, and K-Rb. Rötger's interpretation of the internal friction of mixed-alkali silicate glasses is shown to be incorrect. A previously unreported internal friction peak was observed whenever two different alkali oxides were …

The Microbial Hydrolysis Of Cellulose And Some Factors Affecting The Production Of Cellulase In A Submerged Culture Of Alternaria Sp, Robert Murray Logan

Doctoral Dissertations

"A mile hydrolyzing procedure was utilized to degrade oak sawdust. Its capability of producing a suitable fermentatation [sic] medium was studied. In the interest of solubilizing, enzymatically, the carbohydrate portion of oak sawdust, an investigation was conducted in which various microorganisms were examined for their ability to utilize different forms of cellulose for their growth and to produce cellulose decomposing enzymes. The microorganisms included a myxobacterium, several fungi, and a wood-rotting basidiomycete. The fungi included two highly cellulolytic organisms, Myrothecium verrucaria and Trichoderma viride. The myxobacterium used was Sorangium cellulosum and the basidiomycete was Pleurotus ostreatus. The principla substrates employed …

Investigation Of Effects Of Cold Forming On Mechanical Properties, Kenneth W. Karren, George Winter

CCFSS Library (1939 - present)

INTRODUCTION All of the divisions of this report consist of either experimental or theoretical investigations of the various aspects of predicting the magnitude and distribution of changes in the mechanical properties (particularly the yield strength) of coldformed members. The prior work performed under this project, was conducted to determine the changes brought about in the mechanical properties of structural sheet steels by (1) simple uniform uni-directional prestrain of varying amounts and (2) simple cold working caused by cold forming sheet into corners as is commonly done in light gage cold formed structural members. Included in this report are: a study …

The Performance Of Beams And Columns Continuously-Braced With Diaphragms, Gordon P. Fisher, S. J. Errera

CCFSS Library (1939 - present)

INTRODUCTION Under the general title of "Performance of Steel-Framed Buildings and Structural Members Braced with Light-Gage Steel Diaphragms", sponsored at Cornell University by the American Iron and Steel Institute, an investigation has been proceeding in two separate but closely interrelated phases, referred to as: Subproject A - Performance of Steel-Framed Buildings Braced with Light-Gage Steel Diaphragms Subproject B - Performance of Beams and Columns Continuously-Braced with Diaphragms. The investigation now referred to as Subproject B was sponsored by the American Institute of Steel Construction from June, 1961 to June, 1963 after which A.I.S.I. assumed sponsorship with the cooperation of A.I.S.C. …

Generalized Programs For Heat Transfer Analysis., Ceylung Chu

Masters Theses

"This report presents numerical methods for calculating temperature distributions in any physical system in which heat transfer is taking place. The syste.11 may be at either a steadystate condition or a transient condition. The temperature distribution may itself be or primary interest, or it may be used further to calculate the flow or heat or thermal stress.

The system under investigation is divided into a certain number of subdivisions, or so-called "regions". A reference point (node point) will be taken as representative for the region which includes that point. The temperature at the "node point11 is taken to be the …

Experimental Evaluation Of Thermal Stresses On The Outer Surface Of A Thick-Walled Tube., Vinodray T. Patel

Masters Theses

"In this investigation an attempt has been made to measure thermal stresses on the outer surface of a thick- walled tube. The inside surface was heated by steam passing through the tube while the outer surface was cooled by water. Two temperature compensated strain gages were used to measure strains in the tangential and axial directions respectively. The advantage of using this type of strain gage is to avoid the use of a dummy gage to compensate for the temperature effect.

The analytical solution to the problem was derived and the values of thermal stresses were calculated theoretically and compared …

Zirconium Chloride Nuclear Battery, Lonnie J. Shalton

Masters Theses

"An investigation of the neutron absorption characteristics of zirconium chloride was made to verify the reports of Chicago Development Corporation (5810 47th Ave., Riverdale, Md.) that ZrCl Blight be used as a power source for a nuclear battery. The company detected what they believed to be a beta current when the ZrCl was bombarded with neutrons from a slightly enriched uranium source. Investigation using higher powered neutron sources revealed that such a current was highly improbable and the company incorrectly interpeted the phenomena. Reports in the literature also confirmed that an electric current from the ZrCl using a low powered …

A Study Of The Eddy Diffusivity In Turbulent Heat Transfer, Frank Fu-Kun Tao

Doctoral Dissertations

"The purpose of this investigation was to determine the eddy thermal diffusivity values as a function of radial position at various Reynolds numbers for a fluid flowing turbulently in a pipe. The ratios of the eddy thermal diffusivity and the eddy viscosity were also investigated.

A vertical column of copper tube two inches in diameter was constructed which consisted of an entrance section for the development of the velocity profile and a heating section for the development of the temperature distribution. The heating section was jacketed and maintained at a constant wall temperature at about 103 ° F by the …

Lattice Parameters, Thermal Expansion Coefficients, Densities, And Imperfections In Silver And In The Alpha-Phase Of The Silver-Indium System, Samir Moustafa Riad

Doctoral Dissertations

“An investigation of structure insensitive properties (lattice parameters, thermal expansion coefficients, densities, and imperfections) of silver and the α-phase of the silver-indium system was suggested by the desirable uses for silver and its indium alloys.

Both silver and indium used were 99.999 per cent pure. The silver-indium alloys were prepared by melting both metals inside evacuated and sealed fused quartz tubes. The solidified alloys were annealed and then examined by X-ray diffraction for homogeneity.

This experimental work is divided into three main parts:-

I. X-ray diffraction investigation to determine the solid solubility limit of the Ag-In α-phase at 25° C, …

A Study Of Plane And Spherical Compressional Waves In A Voigt Viscoelastic Medium, Gerald B. Rupert

Doctoral Dissertations

"In investigating the behavior of waves traveling through cohesive solids, two assumptions are usually made: that the propagating medium is either elastic or viscoelastic, and that the wave is either planar or spherical in form. For small distances from the source of the disturbance the medium can be considered elastic and the wave spherical rather than planar. The assumption of elasticity allows considerable simplification of the mathematical analysis, and assuming a spherical wave form is an acceptable approximation if the initial disturbance is essentially a point source and the propagating medium is nearly homogeneous. However, for large distances from the …