Engineering Commons^™

The Dynamic Behavior Of Steel Frame And Truss Buildings, Dixon Rea, Jack G. Bouwkamp, R. W. Clough

CCFSS Library (1939 - present)

This report describes experimental and analytical studies of the dynamic behavior of the East Building of the University of California's new Medical Center at San Francisco, California. It also describes experimental tests conducted on the East Building's mechanical service tower and on an adjacent elevator tower. Experimental tests on the East Building were conducted in the summers of 1964 and 1965. Vibrations were produced by eccentric-masstype vibration generators. Frequency responses, time responses, and mode shapes were observed. In the summer 1964 tests, the first mode east-west had 2% of critical damping and the first mode north-south had 1.8%; the values …

Deformation And Energy Absorption Capacity Of Steel Structures In The Inelastic Range, Theodore V. Galambos

CCFSS Library (1939 - present)

This report summarizes the status of knowledge on the inelastic deformability of steel members and frames. It demonstrates that the inelastic response of planar beams, beamcolumns, connections and frames is well understood and can be adequately, though conservatively, predicted by theory provided the loading is static, proportional and monotonic, and adequate provisions are made to inhibit premature local and lateral-torsional instability. The report reviews the available theoretical work, and examines the experimental evidence. It shows that the inelastic rotation capacity, which defines also the "ductility factor" and the inelastic energy absorption capacity, is both predictable and large enough to meet …

Specification For The Design Of Cold-Formed Steel Structural Members, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Estimation Of Film Boiling Heat Transfer Coefficients For Cylindrical Heaters In Corresponding States Fluids, Gary Joseph Capone

Masters Theses

"An investigation of film boiling heat transfer was made with cylindrical heaters. The (0.75" O.D.) gold plated, copper heaters were positioned horizontally in pools of liquid argon, nitrogen, and carbon monoxide. A correlation for film boiling corresponding states fluids is derived and discussed. The correlation is a least squares fit of three variables: the diameter of the cylindrical heater, the reduced pressure of the system, and the temperature difference between the heater surface and the saturated pool"--Abstract, page iii.

Isotope Effect Of Interstitial Diffusion Of Carbon In A Dilute Fe-Si Alloy, Edward T. Yen

Masters Theses

"The isotope effect of carbon interstitial diffusion in a Fe-2.75at%Si alloy has been measured at -3.10°C using the disaccommodation technique. The disaccommodation has been analyzed in terms of two relaxation processes which are discussed on the basis of the reorientation mechanism of carbon interstitials at Fe-Fe sites and Fe-Si sites respectively. The ratios of the relaxation times [tau]₁₃/[tau]₁₂ are 1.0382 for the former and 1.0072 for the latter relaxation process. This result is discussed on the basis of many-body reaction rate theory"--Abstract, page ii.

Zener Disaccommodation In Dilute F.C.C. Co-Ti Alloys, H. B. Aaron, M. (Manfred) Wuttig, H. K. Birnbaum

Materials Science and Engineering Faculty Research & Creative Works

The magnetic Dis accommodation, i.e., the time dependence of the low field magnetic permeability, was investigated in cobalt base alloys containing 0-5.1 at.% (0-4.2 wt.%) titanium in the temperature range 400-700°C. A strong temperature dependence of the Dis accommodation observed in the range 430-530°C could be accounted for predominantly by a single first order relaxation process. Analyzing the data in terms of (a) a single exponential relaxation, (b) a lognormal distribution of relaxation times, and (c) a sum of exponential relaxations, it was shown that the relaxation strength varies as the square of the titanium concentration and that the relaxation …

The Damage Assessment Of Thermally Shocked High Density, High Purity Aluminum Oxide, John H. Ainsworth

Doctoral Dissertations

"The traditional approach to thermal shock testing in brittle materials has been to determine the temperature difference required to nucleate cracks in these materials. Recent work has indicated that the degree of damage after crack nucleation should be an additional consideration. The degree of damage resulting from cooling thermal shocks has been the primary consideration of the present work. Test specimens of two geometries: long, solid rods and short, solid cylinders were quenched from selected temperatures into ice water. The degree of damage was determined through strength measurements and sonic damping analysis. Initial damage occurred at a temperature difference above …

Hrva - A Velocity Analysis Technique For Seismic Data, John Charles Robinson

Doctoral Dissertations

"A High-Resolution Velocity Analysis (HRVA) has been developed for the determination of the root-mean-square subsurface-velocity energy spectrum from gated seismic data which has been normal-moveout corrected. All calculations are performed in the frequency-space or frequency-wavenumber domain; seismic gates are transformed from the time-space domain via the Fast Fourier Transform algorithm. HRVA is not restricted to the investigation of apparent horizontal velocities which have associated stepout values that are integral multiples of the time sampling interval, as are the existing correlation techniques. The technique liberally exploits the inexistence of significant energy in the higher frequency harmonies of seismic data, resulting in …

The Identification And Evaluation Of Toxic Effects Of Organic Micropollutants, John Warren Smith

Doctoral Dissertations

No abstract provided.

Prediction Of Drag Reduction With A Viscoelastic Model, Gary Kent Patterson, J. L. Zakin

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

Numerical Differentiation Of Equally Spaced And Not Equally Spaced Experimental Data [3], Harry C. Hershey, Jacques L. Zakin

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

Transport Of ⁸⁵Sr And ¹³⁷Cs Under Induced Clay Suspensions, Purush Terkonda

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

“The purpose of this study was to evaluate the effect of induced clay suspensions on the transport of ⁸⁵Sr and ¹³⁷Cs in an aqueous environment.

An instrumented flume was used as a model river to simulate an environment typical of a slow-moving, unpolluted, turbid stream. Modified longitudinal dispersion relationships were used to describe the transport of radionuclides in turbid streams. Data were derived from instantaneous release of ⁸⁵Sr and ¹³⁷Cs with suspended Attapulgite and Kaolinite clays. Continuous release of ¹³⁷Cs with an Attapulgite clay suspension helped to establish uptake and transport characteristics for one environmental …

Recombination Statistics For Neutron Bombarded Silicon Transistors, M. C. Chow, J. L. Azarewiczt, C. A. Goben

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents a recombination statistical model for the neutron-induced base current component reported previously. The derivation was based on the following: 1) the current equation for the induced current component developed previously; 2) the Shockley-Read-Hall statistics for holes and electrons; and 3) the recombination statistics derived by Sah, Noyce and Shockley for sites in the bulk space-charge region. The recombination statistics model depends on the diffusion potential, the junction voltage, the activation energy, temperature, and the ratio of capture cross-sections for holes and electrons. The utility of such a recombination statistical model is illustrated by using measured parameters to …

Neutron Radiation Damage In Silicon Transistors, C. A. Goben, F. M. Smits, J. L. Wirth

Electrical and Computer Engineering Faculty Research & Creative Works

In the investigation of base and collector current as a function of the emitter-to-base voltage, previous studies have shown that neutron-induced base current has components originating in the emitter space charge region as well as the neutral base region. This study shows that while the low injection level neutron-induced base current is dominated by the space charge component, the high injection behavior appears to be controlled by recombination in the neutral base region. Additional experiments performed in special tetrode transistors and van der Pauw-type samples indicate that changes in collector current are dominated by recombination in the neutral base, while …

A Simple Design Algorithm For Synthesis Of Multilevel Combinational Networks, James H. Tracey

Electrical and Computer Engineering Faculty Research & Creative Works

An algorithm is presented for the synthesis of combinational networks with a constrained arrangement of ANDS, ORS, NANDS, NORS, and inverters. The algorithm is easily presented to students in an introductory logic design course and has considerable application in modern practical logic design. Many texts available for a first course in logic design give very limited practical guidance for synthesis of networks under constraints outlined here. It is suggested that the algorithm presented here be furnished as supplementary material in the introductory course. Copyright © 1968 by The Institute of Electrical and Electronics Engineers, Inc.

A Direct Method Of Measuring Stray Load Loss In Dc Machines, Kanaiyalal R. Shah, George Mcpherson

Electrical and Computer Engineering Faculty Research & Creative Works

Stray load loss in dc machines is denned as the difference between the actual loss under load and the well-recognized loss. This paper describes a simple, reliable, and direct method of measuring this loss by means of a proposed short-circuit test with a correction factor for uncompensated-type dc machines. It also describes the sources and components of stray load losses as they occur under short-circuit test. Copyright © 1968 by The Institute of Electrical and Electronics Engineers, Inc.

Radiation And Annealing Characteristics Of Neutron Bombarded Silicon Transistors, L. S. Su, G. E. Gassner, C. A. Goben

Electrical and Computer Engineering Faculty Research & Creative Works

Operating a silicon planar epitaxial transistor in the inverse configuration allows one to demonstrate clearly the importance of the neutron-induced base current component and its degradation of the emitter efficiency, and, because of the much larger depletion layer, to compute a volume dependent damage constant applicable to all silicon p-n junctions. The importance of minimizing the absolute change versus relative change in radiation hardening studies is clearly illustrated. Surface effects were found to be significant for transistors mounted in gas-filled cans. The diffusion potential was predicted, on theoretical grounds, to vary with neutron fluence, and the theory was experimentally confirmed. …

Waveform Distortion Caused By A Plasma Sheath, James R. Carl

Masters Theses

"A short burst of electromagnetic energy that propagates into and through a plasma medium can react with the plasma medium in several different ways depending on both the characteristics of the plasma and of the pulse. This thesis derives approximations for the plasma transfer function at low pressure (high altitude) and at high pressure (low altitude). The mechanisms that can change the shape of a waveform, in general, are dispersion and breakdown. dispersive distortion at low altitude is shown to exist for electron concentrations well above the resonant concentration for plasma sheaths that are thin compared to one wavelength. Several …

Influence Of Continuous Precipitation Upon The Growth Kinetics Of The Cellular Reaction In An Al-Ag Alloy, H. I. Aaronson, J. B. Clark

Materials Science and Engineering Faculty Research & Creative Works

The influence of the prior formation of a continuous precipitate upon the growth kinetics of the cellular reaction has been evaluated in an Al-17.9 wt. % Ag alloy. The continuous precipitate, in the form of intragranular plates of the γ′ transition phase, was shown to have reduced the upper bound of the driving force for the cellular reaction from the silver content of the untransformed alloy to that corresponding to the coherent solvus. When this reduction (≥ 98 %) is taken into account, the growth of cells is found to be controlled by cell boundary rather than by volume diffusion …

Age Hardening In A Mg-9 Wt.% Al Alloy, J. Beverley Clark

Materials Science and Engineering Faculty Research & Creative Works

The precipitation process and age hardening mechanism in a Mg-9 wt.% Al alloy were studied principally by transmission electron microscopy. This alloy age hardens by the general precipitation of plates of the equilibrium Mg₁₇Al₁₂ phase on the basal plane of the magnesium solid solution matrix. No evidence for the formation of either G.P. zones or a transition lattice of the Mg₁₇Al₁₂ precipitate was obtained. Cellular precipitation occurs competitively with the general precipitation at nearly all age hardening temperatures. In the solution treated condition, basal slip and {101̄2} twins are the principal deformation modes. Precipitation …

A Novel Method For Solving The Uniform Distributed Network Analysis Problem, Robert C. Peirson, Edward C. Bertnolli

Electrical and Computer Engineering Faculty Research & Creative Works

An application of the Laplace transform method of Ogata to the solution of the uniform distributed network analysis problem is described. Copyright © 1968 by The Institute of Electrical and Electronics Engineers, Inc.

Design Of Truncated Sequential Tests For Rapidly Fading Radar Targets, Norval D. Wallace

Electrical and Computer Engineering Faculty Research & Creative Works

Curves and equations are presented from which the exact performance of truncated sequential tests can be determined for one important case: the biased square-law detector for the detection of rapidly fading targets. The method of generating functions is used to derive probability distributions for sample size. It is shown how these probability distributions can be used to determine truncation errors and the effects of multiple-resolution elements. Sample calculations are performed to determine the effects of a particular truncation procedure. Copyright © 1968 by The Institute of Electrical and Electronics Engineers, Inc.

Electric Field Investigations And A Model For Electrical Liquid Spraying, Wallace E. Deshon, Ralph S. Carson

Electrical and Computer Engineering Faculty Research & Creative Works

The equation generally used for determining the electric field at the liquid tip in electrical spraying of liquids was originally derived for determining the electric field around a metal tip in the extraction of electrons from metals. In the present paper experimental data were taken at the instant of spraying to determine the validity of using this equation for liquid tips. the results indicate that the value of electric field given by this equation needs to be increased by about 20% in the normal range of operation. A model for the spraying mechanism of the liquid is also presented. © …

Chemical Precipitation Of Phosphorous With Sodium Aluminate And Alum In The Activated Sludge Aeration Chamber, Richard Charles Vedder

Masters Theses

"The purpose of this investigation was to study the removal of phosphorus by chemical precipitation with sodium aluminate and alum in the activated sludge aeration chamber, and determine the effect of the aluminum to phosphorus ratio and the mixed liquor suspended solids concentration on the phosphorus removal efficiency and the effect of the precipitants on the removal of organic pollutants in the activated sludge process. The studies were conducted on settled domestic sewage in three bench-scale continuous flow activated sludge units supplemented with jar tests. Major parameters employed included influent and effluent total phosphorus and chemical oxygen demand (COD), mixed …

Pressure Welding Of Continuously Cast Nodular Iron, Gerald W. Wille

Masters Theses

"The objective of this study was to determine the feasibility of using pressure welding as a joining technique for swaged nodular iron.

Test pressure welds were produced with swaged continuous cast nodular iron at temperatures between 1750⁰F and 2050⁰F with welding pressures between 15,900 psi and 51,400 psi using an induction coil to heat the weld zone.

Pressure welds of greater strength than the as-received nodular iron were produced by swaging the material before welding. The optimum welding parameters were a temperature of 2050⁰F with a welding pressure of 46,700 psi.

On the basis of these tests it is concluded …

Scattering Parameter Measurements And Amplifier Design, Thomas J. Herrick

Masters Theses

"The scattering parameter formulation in describing the small-signal operation of an active two-port device is developed. The inherent advantages of measuring the scattering parameters at UHF frequencies and the clear insight into the design problem are demonstrated. Some of the practical difficulties in a typical design problem are also considered"--Abstract, page ii.

Engineering Properties Of Bloomington-Normal Subsoils, Rohn Dunseth Abbott

Masters Theses

"The glacial subsoils of the Bloomington-Normal, Illinois area have been analyzed with regard to their engineering properties. Several boring logs are included to illustrate the horizontal and vertical variability in soil units encountered and in the engineering properties of these soil units. The engineering properties of the two most common foundation soils, the Bloomington and Normal tills are compared and special consideration is given to evaluating the compressibility of these materials. Evidence is presented that indicates that the circumferential trimming of a highly preconsolidated soil containing stones can cause significant sample disturbance. Special sampling techniques which eliminate circumferential trimming yield …

Analytical And Experimental Methods For Determining The Properties Of Materials At Very High Rates Of Loading, A. G. Behring

Masters Theses

"In the following report, some of the properties of ALCOA 7075 T651 aluminum, when subjected to high rates of loading, are experimentally investigated by impacting two rods of the material longitudinally. One rod is accelerated to a uniform velocity with an air gun launcher. The stationary second rod is instrumented with strain gages on its lateral surface in order to determine the strain-time history following impact. A detailed description of the experimental equipment is included. Simple, one-dimensional theory is used to determine the dynamic, elastic modulus of the test material under the impact condition. Several observations regarding the behavior of …

The Design Of A Hybrid Computer System, James Joseph Becker

Masters Theses

"Three typical hybrid computers in industry and educational institutions are presented. The hybrid computer designed and built at the University of Missouri at Rolla consists of an SCC-650 digital computer, a TR-48 analog computer, and a hybrid interface. The interface permits the digital computer to control the modes of operation on the analog computer. There are also 9 multiple-pole relays on the interface that can be controlled by the digital computer. A 320 hold removable patchboard is included in the interface. There are 40 trunks lines from the analog computer that are present on the patchboard. The 4 digital-to-analog channels …

The Design Of A Tape Deck Controller, Frederick Harold Keeve

Masters Theses

"A controller was built to interface the SCC-650 general purpose digital computer and the Kennedy Model 1400R incremental write/continuous read tape unit. All logic design information, signal lists, and tape deck instructions are included"--Abstract, page ii.