Engineering Commons^™

Fabrication And Mechanical Property Analysis Of A Transparent, Glass Fiber Reinforced Polymer Matrix Composite, James R. Olson

Masters Theses

"A "transparent” composite was produced by reinforcing poly(methyl methacrylate) (PMMA) with unidirectional borosilicate glass fibers. Composites with 40 volume percent fiber had a modulus of rupture of 600 MPa which is six times greater than that of pure PMMA. Young's modulus for the same composite was 18 MPA which is nine times greater than the 2 MPa measured for pure PMMA. Work of fracture was 110 kJ/m² or more than double the 45 kJ/m² required to fracture pure PMMA. The optical transmission of the composite with 30 volume percent fiber was approximately 40 percent through a 10 mm …

A Three-Dimensional Bistatic Radar Target Position Measurement Error Model, Robert Kenneth Lynn

Masters Theses

"The accuracy of target position measurements for an airborne bistatic radar receiver are calculated. Two methods of information measurement are utilized, both of which assume cooperative synchronization between the transmitter and receiver. Gimbal angle errors are incorporated into both methods. The size and orientation of the error ellipsoid about the true target position is found. Loci of constant circular error probable are plotted in a horizontal plane of interest"--Abstract, page ii.

The Effect Of Additives On Properties Of Pfn-Pfw Dielectric Materials, Weih-Min Liao

Masters Theses

"The purpose of this study was to investigate the effect of processing and additives on the properties of the Pb(Fe_1/2Nb_1/2)O₃-PB(Fe_2/3W_1/3)O₃ solid solutions. The basic composition was 70 m% Pb(Fe_1/2Nb_1/2)O₃ and 30 m% Pb(Fe_2/3W_1/3)O₃. The additives used were MnO, PbO and ZnNbO₆. Pressed compacts were sintered over the temperature range 900'C to 1050°C for 1 to 5 hours.

The influence of processing and composition on the properties was determined by measurement of density, shrinkage, dielectric constant, dissipation factor and …

Reductive Stripping Of Iron(Iii) From Di(2-Ethylhexyl) Phosphoric Acid, Byron G. Belew

Masters Theses

"Unwanted impurities, present in raw materials, are often coextracted along with desired constituents during leaching. If left unchecked, impurity levels may increase in hydrometallurgical process streams until their presence has deleterious effects upon subsequent unit processes. Due to its abundance and ease of extraction, the presence of ferric iron in solvent extraction circuits has always been a problem. The technique proposed herein constitutes a novel approach to remove iron from zinc hydrometallurgical circuits; but the principles employed may find a variety of applications.

This research investigated the reduction and stripping of ferric iron from di(2-ethylhexyl) phosphoric acid into a …

Analysis Of Interrelationships Between Photovoltaic Power And Battery Storage For Electric Utility Load Management, Badrul H. Chowdhury, S. Rahman

Electrical and Computer Engineering Faculty Research & Creative Works

The impact of photovoltaic power generation on an electric utility's load shape under supply-side peak load management conditions is explored. Results show that some utilities utilizing battery storage for peak load shaving might benefit from use of photovoltaic (PV) power, the extent of its usefulness being dependent on the specific load shapes as well as the photovoltaic array orientations. Typical utility load shapes both in the eastern (at Rayleigh, NC) and in the western (at Hesperia, CA) parts of the USA are examined for this purpose. It is concluded that while photovoltaic power generation seems to present a bigger impact …

Comments On A Paper By No, Esnouf, San Juan, And Fontozzi, Hollis P. Leighly

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

South East Missouri Lead Belt - A Review 1987, Johh L. Watson

Materials Science and Engineering Faculty Research & Creative Works

The south-east Missouri Lead Belt is, and has been for many years, a major world producer of lead concentrate. This paper reviews the current mill operations in the area and presents detailed information on equipment, operating parameters and metallurgical performance. © 1988.

Sealing Glasses For Titanium And Titanium Alloys, Richard K. Brow, R. D. Watkins

Materials Science and Engineering Faculty Research & Creative Works

Glass compositions containing calcium oxide, alumina, boric oxide, strontium oxide and barium oxide in various mole % combinations were studied. These compositions are capable of forming stable glass to metal seals with titanium and titanium alloys for use as seals for battery headers.

Power Filter Resonant Frequency Modulation Network, Don Cronin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A power filter resonant frequency modulation network for coupling between a load and a variable voltage direct current power source which is subjected to superposition of alternating current thereon at various frequencies and at various voltage levels, the filter including first and second series inductor arrangements in the positive and negative buses between the power supply and the load, with capacitive elements in parallel between the two buses. Each series inductor arrangement includes a first inductor in series with a frequency and voltage responsive inductive load device, which is a second inductor having a tertiary winding loaded with a coil …

Aircraft Vertical Profile Implementation Using Directed-Graph Methods, L. T. Brewster, Paul D. Stigall

Electrical and Computer Engineering Faculty Research & Creative Works

Aircraft Vertical Profile Simulation is Realized using a Demand-Driven Minimal-Calculation Directed Graph Structure to Reduce Calculation Time and to Force Synchronization of the Performance Measurement Functions with the System State Variables. Performance-Directed Model Adaptation Makes Dynamic Vertical Profile Path Corrections, in the Presence of Fixed Drag Variations, Possible. Drag Variations Ranging from + 10 Percent to - 10 Percent Yielded Fuel Consumption Improvements of Less Than 1 Percent in the Majority of the Cases. Calculation Time Improvement for Path Simulation Ranges from a Factor of 1.19 in the Worst Case to 1.5 in the Best Case. © 1988 IEEE

A Stochastic Model For Dielectric Breakdown In Thin Capacitors, D. A. Willming, Cheng-Hsiao Wu

Electrical and Computer Engineering Faculty Research & Creative Works

A nontrivial two-dimensional stochastic model for dielectric breakdown within a parallel plate capacitor is presented for the first time. The model has been used to determine geometric properties of parallel plate discharges. Comparisons are made between these properties and known fractal properties of electrostatic discharges within cylindrical geometries. As the spacing between the plates of a capacitor increases, the value of the fractal dimension of the associated discharge structure increases from the minimum value of unity and approaches the limiting value corresponding to the case of infinite spacing. For any given spacing, this fractal exponent is equal to the exponent …

Toward The Development Of A Knowledge-Based Construction Schedule Planning System, Nordin Bin Yunus

Doctoral Dissertations

"This research attempts to model and prototype a knowledge-based system for use in the construction industry to accomplish the automatic generation of initial construction schedules. The schedule can be transformed into a logical network that provides a physical representation of the construction operations plan. The prototype system, which requires symbolic processing and reasoning, is developed based on an intensive modeling that rationally examines industry practice.

The model identifies work breakdown and precedence relationship as the two major concepts in schedule planning. Work breakdown is concerned with the identification of construction activities that result in the completion of project elements. Precedence …

Still-Frame Image Transmission Using Dpcm/Interpolative Coding, Brindala Mallappa, Norman R. Cox

Electrical and Computer Engineering Faculty Research & Creative Works

Two methods of combining DPCM (differential pulse-code modulation) and interpolation are proposed for compressing still-frame teleconferencing signals. The first method uses horizontal subsampling, DPCM, and interpolation to achieve a 4:1 compression. The other method is similar but uses vertical subsampling instead. Simulation results indicate that either method can easily achieve the required 2-b/pel data rate with negligible degradation in image quality. Conventional DPCM is shown to perform slightly better in quantitative terms when fixed-wordlength coding is used. However, the two DPCM/interpolation methods offer other advantages when used with a variable-wordlength coder

Is Central Station Photovoltaic Power Dispatchable?, Badrul H. Chowdhury, S. Rahman

Electrical and Computer Engineering Faculty Research & Creative Works

An operational tool for integrating a photovoltaic system into the utility's generation mix is introduced. The development and implementation of a new approach-a dynamic rule-based (RB) dispatch algorithm-is presented. A Box-Jenkins time-series method is used to model the subhourly solar irradiance. The model is extended to yield forecast parameters which are then used to predict the photovoltaic output expected to occur at certain lead times coinciding with the economic dispatch intervals. The RB dispatch algorithm is introduced to operate as either a substitute for or an aid to the dispatch operator. It is concluded that results depend on the time …

A Practical C Language Compiler/Optimizer For Real-Time Implementations On A Family Of Floating Point Dsps, J. Hartung, Steven L. Grant, S. G. Haigh

Electrical and Computer Engineering Faculty Research & Creative Works

Digital signal processors (DSPs) have traditionally been used in real-time applications with very high data throughput. For this reason, system designers have been reluctant to accept the degradation in performance inherent in machine code compiled from high-level languages such as C. The problem is compounded by the fact that DSPs use pipelined architectures to achieve their high data throughput, resulting in hazards and latencies between instructions. Simple compiler implementation cannot take advantage of latent instructions, resulting in a conservative and inefficient executable program. This problem has been addressed in the C compiler package for the AT&T WE DSP32 by the …

University Of Missouri-Rolla Cloud Simulation Facility: Proto Ii Chamber, Daniel R. White, James L. Kassner, John C. Carstens, Donald E. Hagen, John L. Schmitt, Darryl J. Alofs, Alfred R. Hopkins, Max B. Trueblood, Max W. Alcorn, William L. Walker

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Graduate Center for Cloud Physics Research at UMR Has Developed a Cloud Simulation Facility to Study Phenomena Occurring in Terrestrial Clouds and Fogs. the Facility Consists of a Pair of Precision Cooled-Wall Expansion Chambers Along with Extensive Supporting Equipment. the Smaller of These Chambers, Described in This Article, is Fully Operational, and is Capable of Simulating a Broad Range of In-Cloud Thermodynamic Conditions. It is Currently Being Used to Study Water Drop Growth and Evaporation for Drops Nucleated (Activated) on Well-Characterized Aerosol Particles. Measurements Have Been Made Not Only for Continuous Expansions (Simulated Updraft) But Also for Cyclic Conditions, …

Transient Stability Simulation By Waveform Relaxation Methods, Marija D. Ilić, M. A. Pai, Mariesa Crow

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, a new methodology for power system dynamic response calculations is presented. The technique known as the waveform relaxation has been extensively used in transient analysis of VLSI circuits and it can take advantage of new architectures in computer systems such as parallel processors. The application in this paper is limited to swing equations of a large power system. Computational results are presented.

Nucleation And Growth Of Zinc Electrodeposited From Acidic Zinc Solutions, A. C. Beshore, B. J. Flori, G. Schade, Thomas J. O'Keefe

Materials Science and Engineering Faculty Research & Creative Works

The nucleation and initial crystal growth kinetics by electrodeposition from acidic zinc solutions was studied in the absence and presence of antimony and glue on a glassy carbon electrode. Zinc exhibits instantaneous nucleation under the experimental conditions employed in the potential region from -1600 to -2000 mV (mercurous sulphate reference). At low overpotentials antimony and glue increase the number of nuclei. © 1987 Chapman and Hall Ltd.

Design Of Automotive Structural Components Using High Strength Sheet Steels Structural Behavior Of Members Consisting Of Flat And Curved Elements, M. Brad Parks, Wei-Wen Yu

CCFSS Library (1939 - present)

Local buckling of stiffened and unstiffened curved elements has been investigated both experimentally and analytically. Stiffened curved elements are supported along both longitudinal edges while unstiffened curved elements are supported along one longitudinal edge with the other longitudinal edge free. A series of stub column, beam, and shear tests have been performed for sections containing curved elements. The tested specimens were formed from sheet steels with yield strengths ranging from 27 to 88 ksi. The radius-to-thickness, R/t, values of the curved elements varied from 12 to 438 whereas the arc length-to-thickness, b/t, ratios ranged from 23 to 218. As a …

Power Division By Element Design In A Circularly Polarized, Series-Fed Array, James L. Drewniak, P. E. Mayes

Electrical and Computer Engineering Faculty Research & Creative Works

The feasibility of designing a wideband circular polarized (CP) array of series-fed elements using the element geometry to control the array excitation has been demonstrated. The simple array of wideband, low-profile CP elements requires no phase-shifters and only sufficient feed lines for the interconnection of the elements in a series-fed array. A complicated network is not required to obtain the excitation coefficients for a specified design. Rather, the excitation coefficients can be realized by utilizing the geometric parameters of the individual elements.

A Dual Circular Polarization Radiating-Line Antenna, James L. Drewniak, P. E. Mayes, D. Tanner, J. Woodruff

Electrical and Computer Engineering Faculty Research & Creative Works

No abstract provided.

University Of Missouri--Rolla Cloud Simulation Facility: Proto Ii Chamber, Daniel R. White, James L. Kassner, John C. Carstens, Donald E. Hagen, John L. Schmitt, Darryl J. Alofs, Alfred Raymond Hopkins, Max B. Trueblood, Max W. Alcorn, William L. Walker

Physics Faculty Research & Creative Works

The Graduate Center for Cloud Physics Research at UMR has developed a cloud simulation facility to study phenomena occurring in terrestrial clouds and fogs. The facility consists of a pair of precision cooled-wall expansion chambers along with extensive supporting equipment. The smaller of these chambers, described in this article, is fully operational, and is capable of simulating a broad range of in-cloud thermodynamic conditions. It is currently being used to study water drop growth and evaporation for drops nucleated (activated) on well-characterized aerosol particles. Measurements have been made not only for continuous expansions (simulated updraft) but also for cyclic conditions, …

Steel Deck Institute, Inc. Design Manual For Composite Decks, Form Decks, And Roof Decks, Steel Deck Institute

Steel Deck Institute (SDI) Specifications and Manuals (1939 - present)

No abstract provided.

Characteristic Surfaces For Three-Position Motion Generation With Planar Four-Bar Mechanisms, Clark R. Barker, J. Baumann

Mining Engineering Faculty Research & Creative Works

This paper considers the relationship between the three-position motion generation problem and the solution space for planar four-bar mechanisms. After one half of the basic four bar had been selected, two infinities of solutions still remained. These solutions are mapped in a plane to determine where the particular types of mechanisms occur. A contour is then generated in the mapping plane which joins together all solutions which share a common characteristic in regard to their link lengths. This same contour can be displayed in the solution space and in the Cartesian plane in which the motion generation is defined. Significant …

Characteristic Surfaces For Three-Position Motion Generation With Planar Four-Bar Mechanisms., Clark R. Barker, J. Baumann

Mining Engineering Faculty Research & Creative Works

This paper considers the relationship between the three-position motion generation problem and the solution space for planar four-bar mechanisms. After one half of the basic four bar had been selected, two infinities of solutions still remained. These solutions are mapped in a plane to determine where the particular types of mechanisms occur. A contour is then generated in the mapping plane which joins together all solutions which share a common characteristic in regard to their link lengths. This same contour can be displayed in the solution space and in the Cartesian plane in which the motion generation is defined.

Bubble Formation, Movement And Distortion In Viscous Glass, Simon Cheng-Ping Wang

Doctoral Dissertations

"A study of bubble formation, movement and distortion in viscous glass is described. A glass rod containing an irregularly shaped hole is heated to a temperature at where the glass viscosity is low enough to let the hole form a spherical bubble. Spheration occurs as the bubble moves upward in the glass rod. At the proper time, the rising bubble is decelerated and brought to a stop by increasing the glass viscosity by slowly reducing the temperature. The entrapped bubble is then cut from the glass rod and heated again, if necessary, to a lower temperature, to reduce distortion of …

Calculation Of Mass Transfer Coefficients In Metal Deposition Using Electrochemical Tracer Techniques, Thomas J. O'Keefe, J. S. Cuzmar, S. F. Chen

Materials Science and Engineering Faculty Research & Creative Works

A modification of the tracer technique of Ettel has been developed for determining mass-transfer coefficients in electrolytes for both electrowinning and electrorefining systems. The method involves the direct measurement of the limiting current density of a more noble tracer ion at low concentration by cyclic voltammetry techniques in an electrolyte of choice. A Ag+tracer in acid copper sulfate is used as the example. Additional tests were made by code positing the tracer with copper to compare the results of the two methods. The effect of copper ion concentration and temperature on the electrochemical and transport properties of the solution were …

Characteristic Surfaces For Three Position Function Generation With Planar Four Bar Mechanisms, Clark R. Barker, P. L. Tso

Mining Engineering Faculty Research & Creative Works

This paper considers the relationship between the three-position function generation problem and the solution space for planar four bar mechanisms. The two infinities of solutions possible are mapped in a plane to determine the locations where particular types of mechanisms occur. It is possible to generate a contour in the mapping plane which joins together all solutions which possess a common characteristic in regard to their link lengths. This same contour can be displayed in the solution space to ascertain the overall characteristics of potential solutions to the design problem. A numerical example is used for illustrative purposes, but the …

Letters To The Editor, Partho Neogi

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

Modeling And Analysis Of Biospecific Adsorption In A Finite Bath, B. H. Arve, Athanasios I. Liapis

Chemical and Biochemical Engineering Faculty Research & Creative Works

A general model is presented and used to predict the dynamic behavior of the adsorption and wash stages of bio specific adsorption (affinity chromatography) in a finite bath. The model accounts for film and diffusional mass transfer resistances as well as for the rates of interaction between adsorbates and ligands. The model is applicable to single and multicomponent bio specific as well as nonspecific adsorption, and the adsorbates may be monovalent or multivalent. The predictions of the model are compared with the experimental data of the adsorption of β‐galactosidase onto immobilized anti‐β‐galactosidase. The results of bio specific adsorption of bivalent …