Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Cleveland State University

Series

Discipline
Keyword
Publication Year
Publication

Articles 1 - 30 of 651

Full-Text Articles in Engineering

Generalized Conditional Feedback System With Model Uncertainty, Chengbo Dai, Zhiqiang Gao, Yangquan Chen, Donghai Li Jan 2024

Generalized Conditional Feedback System With Model Uncertainty, Chengbo Dai, Zhiqiang Gao, Yangquan Chen, Donghai Li

Electrical and Computer Engineering Faculty Publications

Model uncertainty creates a largely open challenge for industrial process control, which causes a trade-off between robustness and performance optimality. In such a case, we propose a generalized conditional feedback (GCF) system to largely eliminate conflicts between robustness and performance optimality. This approach leverages a nominal model to design an optimal control in the virtual domain and defines an ancillary feedback controller to drive the physical process to track the trajectory of the virtual domain. The effectiveness of the proposed GCF scheme is demonstrated in a simulation for six typical industrial processes and three model-based control methods, and in a …

Go to article

Permeable Concrete Barriers To Control Water Pollution: A Review, Rehab O. Abdel Rahman, Ahmed M. El-Kamash, Yung-Tse Hung Nov 2023

Permeable Concrete Barriers To Control Water Pollution: A Review, Rehab O. Abdel Rahman, Ahmed M. El-Kamash, Yung-Tse Hung

Civil and Environmental Engineering Faculty Publications

Permeable concrete is a class of materials that has long been tested and implemented to control water pollution. Its application in low-impact development practices has proved its efficiency in mitigating some of the impacts of urbanization on the environment, including urban heat islands, attenuation of flashfloods, and reduction of transportation-related noise. Additionally, several research efforts have been directed at the dissemination of these materials for controlling pollution via their use as permeable reactive barriers, as well as their use in the treatment of waste water and water purification. This work is focused on the potential use of these materials as …

Go to article

Blockchain-Based Applications For Smart Grids: An Umbrella Review, Wenbing Zhao, Quan Qi, Jiong Zhou, Xiong Luo Qi Aug 2023

Blockchain-Based Applications For Smart Grids: An Umbrella Review, Wenbing Zhao, Quan Qi, Jiong Zhou, Xiong Luo Qi

Electrical and Computer Engineering Faculty Publications

This article presents an umbrella review of blockchain-based smart grid applications. By umbrella review, we mean that our review is based on systematic reviews of this topic. We aim to synthesize the findings from these systematic reviews and gain deeper insights into this discipline. After studying the systematic reviews, we find it imperative to provide a concise and authoritative description of blockchain technology because many technical inaccuracies permeate many of these papers. This umbrella review is guided by five research questions. The first research question concerns the types of blockchain-based smart grid applications. Existing systematic reviews rarely used a systematic …

Go to article

Introduction To Data-Driven Systems For Plastics And Composites Manufacturing, Saeed Farahani, Srikanth Pilla, Yun Zhang, Fausto Tucci May 2023

Introduction To Data-Driven Systems For Plastics And Composites Manufacturing, Saeed Farahani, Srikanth Pilla, Yun Zhang, Fausto Tucci

Mechanical Engineering Faculty Publications

Applications of high-performance plastics and composites have widely been expanded to various industries due to their superior properties, such as high strength-to-weight ratio, chemical resistance, and thermal/electrical insulation. However, the numerous possible combinations of polymers and reinforcements/fillers, the variability of these materials, and their complex manufacturing processes pose challenges in terms of efficiently developing new plastics and composites, accurately modeling their properties, and effectively monitoring and controlling their manufacturing processes. Integrating data-driven techniques, such as machine learning, artificial intelligence, and big data analytics, is a promising pathway to overcome these challenges as it is demonstrated by the state-of-the-art research works …

Go to article

Review: Inelastic Constitutive Modeling: Polycrystalline Materials, Mirza Baig, Josiah Owusu-Danquah, Anne A. Campbell, Stephen F. Duffy Phd, Pe May 2023

Review: Inelastic Constitutive Modeling: Polycrystalline Materials, Mirza Baig, Josiah Owusu-Danquah, Anne A. Campbell, Stephen F. Duffy Phd, Pe

Civil and Environmental Engineering Faculty Publications

This article provides a literature review that details the development of inelastic constitutive modeling as it relates to polycrystalline materials. This review distinguishes between inelastic constitutive models that account for nonlinear behavior at the microstructural level, time-independent classic plasticity models, and time-dependent unified models. Particular emphasis is placed on understanding the underlying theoretical framework for unified viscoplasticity models where creep and classical plasticity behavior are considered the result of applied boundary conditions instead of separable rates representing distinct physical mechanisms. This article establishes a clear understanding of the advantages of the unified approach to improve material modeling. This review also …

Go to article

A Comprehensive Study On Non-Proprietary Ultra-High-Performance Concrete Containing Supplementary Cementitious Materials, Seyedsaleh Mousavinezhad, Gregory J. Gonzales, William K. Toledo, Judith M. Garcia, Craig M. Newston, Srinivas Allena Apr 2023

A Comprehensive Study On Non-Proprietary Ultra-High-Performance Concrete Containing Supplementary Cementitious Materials, Seyedsaleh Mousavinezhad, Gregory J. Gonzales, William K. Toledo, Judith M. Garcia, Craig M. Newston, Srinivas Allena

Civil and Environmental Engineering Faculty Publications

Ultra-high performance concrete (UHPC) is a novel cement-based material with exceptional mechanical and durability properties. Silica fume, the primary supplementary cementitious material (SCM) in UHPC, is expensive in North America, so it is often substituted with inexpensive class F fly ash. However, future availability of fly ash is uncertain as the energy industry moves toward renewable energy, which creates an urgent need to find cost-effective and environmentally friendly alternatives to fly ash. This study investigated replacing cement, fly ash, and silica fume in UHPC mixtures with ground granulated blast-furnace slag (GGBFS), metakaolin, and a natural pozzolan (pumicite). To identify acceptable …

Go to article

Towards An Evolved Immersive Experience: Exploring 5g-And Beyond-Enabled Ultra-Low-Latency Communications For Augmented And Virtual Reality, Ananya Hazarika, Mehdi Rahmati Apr 2023

Towards An Evolved Immersive Experience: Exploring 5g-And Beyond-Enabled Ultra-Low-Latency Communications For Augmented And Virtual Reality, Ananya Hazarika, Mehdi Rahmati

Electrical and Computer Engineering Faculty Publications

Augmented reality and virtual reality technologies are witnessing an evolutionary change in the 5G and Beyond (5GB) network due to their promising ability to enable an immersive and interactive environment by coupling the virtual world with the real one. However, the requirement of low-latency connectivity, which is defined as the end-to-end delay between the action and the reaction, is very crucial to leverage these technologies for a high-quality immersive experience. This paper provides a comprehensive survey and detailed insight into various advantageous approaches from the hardware and software perspectives, as well as the integration of 5G technology, towards 5GB, in …

Go to article

Hybrid Fes-Exoskeleton Control: Using Mpc To Distribute Actuation For Elbow And Wrist Movements, Nathan Dunkelberger, Jeffrey Berning, Eric M. Schearer, Marcia K. O'Malley Apr 2023

Hybrid Fes-Exoskeleton Control: Using Mpc To Distribute Actuation For Elbow And Wrist Movements, Nathan Dunkelberger, Jeffrey Berning, Eric M. Schearer, Marcia K. O'Malley

Mechanical Engineering Faculty Publications

Introduction: Individuals who have suffered a cervical spinal cord injury prioritize the recovery of upper limb function for completing activities of daily living. Hybrid FES-exoskeleton systems have the potential to assist this population by providing a portable, powered, and wearable device; however, realization of this combination of technologies has been challenging. In particular, it has been difficult to show generalizability across motions, and to define optimal distribution of actuation, given the complex nature of the combined dynamic system. Methods: In this paper, we present a hybrid controller using a model predictive control (MPC) formulation that combines the actuation of both …

Go to article

Physicochemical Technique In Municipal Solid Waste (Msw) Landfill Leachate Remediation: A Review, Hamidi Abdul Aziz, Siti Fatihah Ramli, Yung-Tse Hung Mar 2023

Physicochemical Technique In Municipal Solid Waste (Msw) Landfill Leachate Remediation: A Review, Hamidi Abdul Aziz, Siti Fatihah Ramli, Yung-Tse Hung

Civil and Environmental Engineering Faculty Publications

Leachate generation is among the main challenging issues that landfill operators must handle. Leachate is created when decomposed materials and rainwater pass through the waste. Leachate carries many harmful pollutants, with high concentrations of BOD, COD, colour, heavy metals, ammoniacal nitrogen (NH3-N), and other organic and inorganic pollutants. Among them, COD, colour, and NH3-N are difficult to be completely eliminated, especially with a single treatment. They should be handled by appropriate treatment facilities before being safely released into the environment. Leachate remediation varies based on its properties, the costs of operation and capital expenditures, as well as the rules and …

Go to article

Coaxial Jets With Disparate Viscosity: Mixing And Laminarization Characteristics, Mustafa Usta, M. R. C. Ahmad, G. Pathikonda, I. Khan, P. Gillis, D. Ranjan, C. K. Aidun Jan 2023

Coaxial Jets With Disparate Viscosity: Mixing And Laminarization Characteristics, Mustafa Usta, M. R. C. Ahmad, G. Pathikonda, I. Khan, P. Gillis, D. Ranjan, C. K. Aidun

Mechanical Engineering Faculty Publications

Mixing of fluids in a coaxial jet is studied under four distinct viscosity ratios, m = 1, 10, 20 and 40, using highly resolved large-eddy simulations (LES), particle image velocimetry and planar laser-induced fluorescence. The accuracy of predictions is tested against data obtained by the simultaneous experimental measurements of velocity and concentration fields. For the highest and lowest viscosity ratios, standard RANS models with unclosed terms pertaining to viscosity variations are employed. We show that the standard Reynolds-averaged Navier-Stokes (RANS) approach with no explicit modelling for variable-viscosity terms is not applicable whereas dynamic LES models provide high-quality agreement with the …

Go to article

Water Quality Engineering And Wastewater Treatment Ii, Yung-Tse Hung, Rehab Abdel Rahman, Hamidi Abdul Aziz, Issam A. Al-Khatib, Tsuyoshi Imai Jan 2023

Water Quality Engineering And Wastewater Treatment Ii, Yung-Tse Hung, Rehab Abdel Rahman, Hamidi Abdul Aziz, Issam A. Al-Khatib, Tsuyoshi Imai

Civil and Environmental Engineering Faculty Publications

In this respect, the modeling of the organic matter removal kinetics from municipal sewerage in horizontal subsurface flow CWs was carried out using a conventional first-order model and sigmoidal k-n model [[12]]. Water is an essential natural compound on earth; all life forms on our planet need water to function properly. The presented water management research in this Special Issue aimed to assess natural water quality in different areas, i.e., Brazil, Palestine, and China. [Extracted from the article]

Go to article

Enhancing The Biological Oxidation Of H2s In A Sewer Pipe With Highly Conductive Concrete And Electricity-Producing Bacteria, Huy Thanh Vo, Tsuyoshi Imai, Masato Fukushima, Kanathip Promnuan, Tasuma Suzuki, Hiraku Sakuma, Takashi Hitomi, Yung-Tse Hung Jan 2023

Enhancing The Biological Oxidation Of H2s In A Sewer Pipe With Highly Conductive Concrete And Electricity-Producing Bacteria, Huy Thanh Vo, Tsuyoshi Imai, Masato Fukushima, Kanathip Promnuan, Tasuma Suzuki, Hiraku Sakuma, Takashi Hitomi, Yung-Tse Hung

Civil and Environmental Engineering Faculty Publications

Hydrogen sulfide (H2S) generated in sewer systems is problematic to public health and the environment, owing to its corrosive consequences, odor concerns, and poison control issues. In a previous work, conductive concrete, based on amorphous carbon with a mechanism that operates as a microbial fuel cell was investigated. The objective of the present study is to develop additional materials for highly conductive concrete, to mitigate the concentration of H2S in sewer pipes. Adsorption experiments were conducted to elucidate the role of the H2S reduction. Additionally, electricity-producing bacteria (EPB), isolated from a municipal wastewater treatment plant, were inoculated to improve the …

Go to article

Data-Driven Dynamic Motion Planning For Practical Fes-Controlled Reaching Motions In Spinal Cord Injury, Derek N.N. Wolf, Antonie J. Van Den Bogert, Eric M. Schearer Jan 2023

Data-Driven Dynamic Motion Planning For Practical Fes-Controlled Reaching Motions In Spinal Cord Injury, Derek N.N. Wolf, Antonie J. Van Den Bogert, Eric M. Schearer

Mechanical Engineering Faculty Publications

Functional electrical stimulation (FES) is a promising technology for restoring reaching motions to individuals with upper-limb paralysis caused by a spinal cord injury (SCI). However, the limited muscle capabilities of an individual with SCI have made achieving FES-driven reaching difficult. We developed a novel trajectory optimization method that used experimentally measured muscle capability data to find feasible reaching trajectories. In a simulation based on a real-life individual with SCI, we compared our method to attempting to follow naive direct-to-target paths. We tested our trajectory planner with three control structures that are commonly used in applied FES: feedback, feedforward-feedback, and model …

Go to article

Effective Short Text Classification Via The Fusion Of Hybrid Features For Iot Social Data, Xiong Luo, Zhijian Yu, Zhigang Zhao, Wenbing Zhao, Jenq-Haur Wang Dec 2022

Effective Short Text Classification Via The Fusion Of Hybrid Features For Iot Social Data, Xiong Luo, Zhijian Yu, Zhigang Zhao, Wenbing Zhao, Jenq-Haur Wang

Electrical and Computer Engineering Faculty Publications

Nowadays short texts can be widely found in various social data in relation to the 5G-enabled Internet of Things (IoT). Short text classification is a challenging task due to its sparsity and the lack of context. Previous studies mainly tackle these problems by enhancing the semantic information or the statistical information individually. However, the improvement achieved by a single type of information is limited, while fusing various information may help to improve the classification accuracy more effectively. To fuse various information for short text classification, this article proposes a feature fusion method that integrates the statistical feature and the comprehensive …

Go to article

Influence Of Salts On The Photocatalytic Degradation Of Formic Acid In Wastewater, Azzah Nazihah Che Abdul Rahim, Shotaro Yamada, Haruki Bonkohara, Tsuyoshi Imai, Yung-Tse Hung, Izumi Kumakiri Nov 2022

Influence Of Salts On The Photocatalytic Degradation Of Formic Acid In Wastewater, Azzah Nazihah Che Abdul Rahim, Shotaro Yamada, Haruki Bonkohara, Tsuyoshi Imai, Yung-Tse Hung, Izumi Kumakiri

Civil and Environmental Engineering Faculty Publications

Conventional wastewater treatment technologies have difficulties in feasibly removing persistent organics. The photocatalytic oxidation of these contaminants offers an economical and environmentally friendly solution. In this study, TiO2 membranes and Ag/TiO2 membranes were prepared and used for the decomposition of dissolved formic acid in wastewater. The photochemical deposition of silver on a TiO2 membrane improved the decomposition rate. The rate doubled by depositing ca. 2.5 mg of Ag per 1 g of TiO2. The influence of salinity on formic acid decomposition was studied. The presence of inorganic salts reduced the treatment performance of the TiO2 membranes to half. Ag/TiO2 membranes …

Go to article

Development Of Non-Proprietary Ultra-High Performance Concrete Mixtures, Tawsif Mohammad Hasan, Levi Gilbert, Srinivas Allena, Josiah Owusu-Danquah, Anthony Torres Nov 2022

Development Of Non-Proprietary Ultra-High Performance Concrete Mixtures, Tawsif Mohammad Hasan, Levi Gilbert, Srinivas Allena, Josiah Owusu-Danquah, Anthony Torres

Civil and Environmental Engineering Faculty Publications

The development of non-proprietary Ultra-High Performance Concrete (UHPC) is one way to reduce the initial cost of construction. However, workability is a major issue for which such mixtures are not practical in field conditions. Ultra-high performance cannot be achieved in field conditions if the concrete is not placed, finished, and compacted properly during placement. In this research, six UHPC mixtures were developed (three with steel fibers and three without fibers) using materials which are readily available on the local marketplace with water-to-cementitious materials ratios ranging between 0.17 to 0.30. The workability was determined using standard ASTM flow table apparatus, and …

Go to article

3d-Printed Piezoelectric Porous Bioactive Scaffolds And Clinical Ultrasonic Stimulation Can Help In Enhanced Bone Regeneration, Prabaha Sikder, Phaniteja Nagaraju, Harsha P.S. Naganaboyina Nov 2022

3d-Printed Piezoelectric Porous Bioactive Scaffolds And Clinical Ultrasonic Stimulation Can Help In Enhanced Bone Regeneration, Prabaha Sikder, Phaniteja Nagaraju, Harsha P.S. Naganaboyina

Mechanical Engineering Faculty Publications

This paper presents a comprehensive effort to develop and analyze first-of-its-kind design-specific and bioactive piezoelectric scaffolds for treating orthopedic defects. The study has three major highlights. First, this is one of the first studies that utilize extrusion-based 3D printing to develop design-specific macroporous piezoelectric scaffolds for treating bone defects. The scaffolds with controlled pore size and architecture were synthesized based on unique composite formulations containing polycaprolactone (PCL) and micron-sized barium titanate (BaTiO3) particles. Second, the bioactive PCL-BaTiO3 piezoelectric composite formulations were explicitly developed in the form of uniform diameter filaments, which served as feedstock material for the fused filament fabrication …

Go to article

Application Of Conductive Concrete As A Microbial Fuel Cell To Control H2s Emission For Mitigating Sewer Corrosion, Tsuyoshi Imai, Huy Thanh Vo, Masato Fukushima, Tasuma Suzuki, Hiraku Sakuma, Takashi Hitomi, Yung-Tse Hung Oct 2022

Application Of Conductive Concrete As A Microbial Fuel Cell To Control H2s Emission For Mitigating Sewer Corrosion, Tsuyoshi Imai, Huy Thanh Vo, Masato Fukushima, Tasuma Suzuki, Hiraku Sakuma, Takashi Hitomi, Yung-Tse Hung

Civil and Environmental Engineering Faculty Publications

Localized biogenic corrosion and extrication of annoying odors caused by hydrogen sulfide (H2S) have long been a big problem in the management of urban sewer systems. H2S emission control in sewers via chemically or biologically normal oxidation processes has also been investigated extensively and is costly. The objective of this work was to develop a new technology to mitigate the concentration of H2S in sewer pipes using conductive concrete. Experimental results after 66 days show that the concentration of hydrogen sulfide significantly decreased when conductive concrete was used as a microbial fuel cell. Both ordinary Portland cement and conductive concrete …

Go to article

Introductory Chapter: Uncertainty Management To Support Pollution Prevention And Control Decisions., Rehab O, Abdel Rahman, Yung-Tse Hung Oct 2022

Introductory Chapter: Uncertainty Management To Support Pollution Prevention And Control Decisions., Rehab O, Abdel Rahman, Yung-Tse Hung

Civil and Environmental Engineering Faculty Publications

No abstract provided.

Go to article

Biological Treatment Of Cannery Wastes, Yung-Tse Hung, Seyedkiarash Sharifiilierdy, Howard H. Paul, Christopher R. Huhnke, Rehab O, Abdel Rahman Oct 2022

Biological Treatment Of Cannery Wastes, Yung-Tse Hung, Seyedkiarash Sharifiilierdy, Howard H. Paul, Christopher R. Huhnke, Rehab O, Abdel Rahman

Civil and Environmental Engineering Faculty Publications

This chapter reviews various methods of cannery wastewater biological treatment, namely up-flow anaerobic sludge blanket (UASB), sequencing batch reactor (SBR), three-stage aerobic rotating biological contactor (RBC), three sequentially arranged reactors (anaerobic-anoxic-aerobic reactors), lagooning, and anaerobic digestion. The general principles for dealing with the uncertainty of general wastewater treatment plants are applied to control the uncertainty in cannery wastewater treatment. An overview of on the application of Monte Carlo, support vector machine (SVM), artificial neural network (ANN), and genetic algorithm to manage the uncertainty in the biological treatment of wastewater is provided.

Go to article

Percutaneous-Reinforced Osteoplasty: A Review Of Emerging Treatment Strategies For Bone Interventions, Nischal Koirala, Jyotsna Joshi, Stephen F. Duffy, Gordon Mclennan Oct 2022

Percutaneous-Reinforced Osteoplasty: A Review Of Emerging Treatment Strategies For Bone Interventions, Nischal Koirala, Jyotsna Joshi, Stephen F. Duffy, Gordon Mclennan

Civil and Environmental Engineering Faculty Publications

Percutaneous-reinforced osteoplasty is currently being investigated as a possible therapeutic procedure for fracture stabilization in high-risk patients, primarily in patients with bone metastases or osteoporosis. For these patients, a percutaneous approach, if structurally sound, can provide a viable method for treating bone fractures without the physiologic stress of anesthesia and open surgery. However, the low strength of fixation is a common limitation that requires further refinement in scaffold design and selection of materials, and may potentially benefit from tissue-engineering-based regenerative approaches. Scaffolds that have tissue regenerative properties and low inflammatory response promote rapid healing at the fracture site and are …

Go to article

Serpentine Micromixers Using Extensional Mixing Elements, George Tomaras, Chandrasekhar R. Kothapalli, Petru S. Fodor Oct 2022

Serpentine Micromixers Using Extensional Mixing Elements, George Tomaras, Chandrasekhar R. Kothapalli, Petru S. Fodor

Physics Faculty Publications

Computational fluid dynamics modeling was used to characterize the effect of the integration of constrictions defined by the vertices of hyperbolas on the flow structure in microfluidic serpentine channels. In the new topology, the Dean flows characteristic of the pressure-driven fluid motion along curved channels are combined with elongational flows and asymmetric longitudinal eddies that develop in the constriction region. The resulting complex flow structure is characterized by folding and stretching of the fluid volumes, which can promote enhanced mixing. Optimization of the geometrical parameters defining the constriction region allows for the development of an efficient micromixer topology that shows …

Go to article

Statistical Modeling And Optimization Of Process Parameters For 2, 4-Dichlorophenoxyacetic Acid Removal By Using Ac/Pdmaema Hydrogel Adsorbent: Comparison Of Different Rsm Designs And Ann Training Methods, Irvan Dahlan, Emilia Eizleen Md Azhar, Siti Roshayu Hassan, Hamidi Abdul Aziz, Yung-Tse Hung Sep 2022

Statistical Modeling And Optimization Of Process Parameters For 2, 4-Dichlorophenoxyacetic Acid Removal By Using Ac/Pdmaema Hydrogel Adsorbent: Comparison Of Different Rsm Designs And Ann Training Methods, Irvan Dahlan, Emilia Eizleen Md Azhar, Siti Roshayu Hassan, Hamidi Abdul Aziz, Yung-Tse Hung

Civil and Environmental Engineering Faculty Publications

In this study, the response surface methodology (RSM) and artificial neural network (ANN) were employed to study the adsorption process of 2,4-dichlorophenoxyacetic acid (2,4-D) by using modified hydrogel, i.e., activated carbon poly(dimethylaminoethyl methacrylate) (AC/PDMAEMA hydrogel). The effect of pH, the initial concentration of 2,4-D and the activated carbon content on the removal of 2,4-D and adsorption capacity were investigated through the face-centered composite design (FCCD), optimal design and two-level factorial design. The response surface plot suggested that higher removal of 2,4-D and adsorption capacity could be achieved at the higher initial concentration of 2,4-D and lower pH and activated carbon …

Go to article

Estimation Of Joint Moments During Turning Maneuvers In Alpine Skiing Using A Three Dimensional Musculoskeletal Skier Model And A Forward Dynamics Optimization Framework, Dieter Heinrich, Antonie J. Van Den Bogert, Werner Nachbauer Jun 2022

Estimation Of Joint Moments During Turning Maneuvers In Alpine Skiing Using A Three Dimensional Musculoskeletal Skier Model And A Forward Dynamics Optimization Framework, Dieter Heinrich, Antonie J. Van Den Bogert, Werner Nachbauer

Mechanical Engineering Faculty Publications

In alpine skiing, estimation of the joint moments acting onto the skier is essential to quantify the loading of the skier during turning maneuvers. In the present study, a novel forward dynamics optimization framework is presented to estimate the joint moments acting onto the skier incorporating a three dimensional musculoskeletal model (53 kinematic degrees of freedom, 94 muscles). Kinematic data of a professional skier performing a turning maneuver were captured and used as input data to the optimization framework. In the optimization framework, the musculoskeletal model of the skier was applied to track the experimental data of a skier and …

Go to article

Effects Of Stepwise Temperature Shifts In Anaerobic Digestion For Treating Municipal Wastewater Sludge: A Genomic Study, Gede Adi Wiguna Sudiartha, Tsuyoshi Imai, Yung-Tse Hung May 2022

Effects Of Stepwise Temperature Shifts In Anaerobic Digestion For Treating Municipal Wastewater Sludge: A Genomic Study, Gede Adi Wiguna Sudiartha, Tsuyoshi Imai, Yung-Tse Hung

Civil and Environmental Engineering Faculty Publications

In wastewater treatment plants (WWTP), anaerobic digester (AD) units are commonly operated under mesophilic and thermophilic conditions. In some cases, during the dry season, maintaining a stable temperature in the digester requires additional power to operate a conditioning system. Without proper conditioning systems, methanogens are vulnerable to temperature shifts. This study investigated the effects of temperature shifts on CH4 gas production and microbial diversity during anaerobic digestion of anaerobic sewage sludge using a metagenomic approach. The research was conducted in lab-scale AD under stepwise upshifted temperature from 42 to 48 ◦C. The results showed that significant methanogen population reduction during …

Go to article

Machine Learning Used In Biomedical Computing And Intelligence Healthcare, Volume Ii, Honghao Gao, Ying Li, Zijian Zhang, Wenbing Zhao May 2022

Machine Learning Used In Biomedical Computing And Intelligence Healthcare, Volume Ii, Honghao Gao, Ying Li, Zijian Zhang, Wenbing Zhao

Electrical and Computer Engineering Faculty Publications

No abstract provided.

Go to article

Cesspits As Onsite Sanitation Facilities In The Non-Sewered Palestinian Rural Areas: Users’ Satisfaction, Needs And Perception., Rehab Thaher, Nidal Mahmoud, Issam A. Al-Khatib, Yung-Tse Hung Mar 2022

Cesspits As Onsite Sanitation Facilities In The Non-Sewered Palestinian Rural Areas: Users’ Satisfaction, Needs And Perception., Rehab Thaher, Nidal Mahmoud, Issam A. Al-Khatib, Yung-Tse Hung

Civil and Environmental Engineering Faculty Publications

The main aim of this research was to assess the problems of using cesspits in the non-sewered areas in the West Bank of Palestine by the means of a questionnaire, with a sample size of 485 households, targeting the cesspits’ owners. People who use cesspits for house onsite wastewater management are not satisfied with them, and most of them complain about high disturbance during discharge of the cesspits (75.5%). Emptying cesspits represents a financial burden, costing 6% of the households’ monthly income. The frequency of cesspits’ emptying decreases substantially when there are onsite GWTPs. People accept that constructing a house …

Go to article

Influence Of Particle Size And Zeta Potential In Treating Highly Coloured Old Landfill Leachate By Tin Tetrachloride And Rubber Seed, Siti Fatihah Ramli, Hamidi Abdul Aziz, Fatehah Mohd Omar, Mohd Suffian Yusoff, Herni Halim, Mohamad Anuar Kamaruddin, Kamar Shah Ariffin, Yung-Tse Hung Mar 2022

Influence Of Particle Size And Zeta Potential In Treating Highly Coloured Old Landfill Leachate By Tin Tetrachloride And Rubber Seed, Siti Fatihah Ramli, Hamidi Abdul Aziz, Fatehah Mohd Omar, Mohd Suffian Yusoff, Herni Halim, Mohamad Anuar Kamaruddin, Kamar Shah Ariffin, Yung-Tse Hung

Civil and Environmental Engineering Faculty Publications

Old leachate normally has a low organic compound content, poor biodegradability and is hard to biologically treat. The efficacy of tetravalent metal salts as a coagulant and the application of a natural coagulant as a flocculant in landfill leachate treatment is still inconclusive. Hence, this study aimed to evaluate the potential application of tin tetrachloride (SnCl4 ) as the main coagulant and the rubber seed (Hevea brasiliensis) (RS) as the natural coagulant aid as the sole treatment in eradicating highly coloured and turbid stabilised landfill leachate present at one of the old local landfills in Malaysia. The standard jar test …

Go to article

Heavy Metals In Harvested Rainwater Used For Domestic Purposes In Rural Areas: Yatta Area, Palestine As A Case Study., Fathi Anabtawi, Nidal Mahmoud, Issam A. Al-Khatib, Yung-Tse Hung Feb 2022

Heavy Metals In Harvested Rainwater Used For Domestic Purposes In Rural Areas: Yatta Area, Palestine As A Case Study., Fathi Anabtawi, Nidal Mahmoud, Issam A. Al-Khatib, Yung-Tse Hung

Civil and Environmental Engineering Faculty Publications

Rainwater harvesting is considered one of the most important water resources in the Palestinian countryside. In this research, the study area chosen for the study was Yatta town in Hebron city. 75 water samples were collected from 74 cisterns in a number of neighborhoods in Yatta, and a structured household survey was conducted with the same households where the water samples were collected. Statistical analysis was made using the SPSS software. An analysis for the samples was made using ICP-MS to test the existence of a number of heavy metals, namely Pb, Cr, Mn, Co, Ni, Cu, Zn and Cd. …

Go to article

Comparison Of Dye Wastewater Treatment Methods: A Review., Bukola M. Adesanmi, Yung-Tse Hung, Howard Paul, Christopher Huhnke Feb 2022

Comparison Of Dye Wastewater Treatment Methods: A Review., Bukola M. Adesanmi, Yung-Tse Hung, Howard Paul, Christopher Huhnke

Civil and Environmental Engineering Faculty Publications

Wastewater is produced by numerous dyes producing and dye consuming industries in their process activities especially the textile industry. These effluents become toxic and harmful to the living things and the environment if not properly treated before being discharged to the environment. In recent decades dye wastewater has been becomes a growing water pollution problem because it is one of the most difficult to treat. To put an end to this problem, viable, efficient, and sustainable method of treatment of dye wastewater and color removal needs to be established. Several research papers have been done over the years on various …

Go to article

Next Last