Engineering Commons^™

Action Potential Simulation Of The Hirudo Medicinalis's Retzius Cell In Matlab, Zechari Ryan Tempesta

Master's Theses

Modification of Hodgkin and Huxley’s experimentally derived set of nonlinear differential equations was implemented to accurately simulate the action potential of the Hirudo Medicinalis’s Retzius cell in MATLAB under analogous conditions to those found in the Retzius cell environment. The voltage-gated sodium and potassium channel responses to changes in membrane potential, as experimentally determined by Hodgkin and Huxley, were manipulated to suit simulation parameters established by electrophysiological Retzius cell recordings. Application of this methodology permitted additional accurate simulation of the Hirudo Medicinalis’s P cell under analogous conditions to those found in the P cell environment. Further refinement of this technique …

Development And Validation Of A Human Knee Joint Finite Element Model For Tissue Stress And Strain Predictions During Exercise, Spencer D. Wangerin

Master's Theses

Osteoarthritis (OA) is a degenerative condition of cartilage and is the leading cost of disability in the United States. Motion analysis experiments in combination with knee-joint finite element (FE) analysis may be used to identify exercises that maintain knee-joint osteochondral (OC) loading at safe levels for patients at high-risk for knee OA, individuals with modest OC defects, or patients rehabilitating after surgical interventions. Therefore, a detailed total knee-joint FE model was developed by modifying open-source knee-joint geometries in order to predict OC tissue stress and strain during the stance phase of gait. The model was partially validated for predicting the …

Development And Validation Of A Human Hip Joint Finite Element Model For Tissue Stress And Strain Predictions During Gait, Jeffrey D. Pyle

Master's Theses

Articular cartilage degeneration, called osteoarthritis, in the hip joint is a serious condition that affects millions of individuals yearly, with limited clinical solutions available to prevent or slow progression of damage. Additionally, the effects of high-risk factors (e.g. obesity, soft and hard tissue injuries, abnormal joint alignment, amputations) on the progression of osteoarthritis are not fully understood. Therefore, the objective of this thesis is to generate a finite element model for predicting osteochondral tissue stress and strain in the human hip joint during gait, with a future goal of using this model in clinically relevant studies aimed at prevention, treatment, …

Formulation Development Of A Polymer-Drug Matrix With A Controlled Release Profile For The Treatment Of Glaucoma, Eric W. Tsoi

Master's Theses

Glaucoma is the leading cause of blindness in the United States accounting for 9-12% of all cases of blindness. Currently, the front line treatment for glaucoma are prostaglandins that may have to be taken up to several times a day. Even with proper treatment, roughly 11% of the patients using the treatment are non-compliant and lose their vision. In this project, ForSight Laboratories has developed a pharmaceutical drug delivering implant with the capability of sustaining long-term release of a prostaglandin as a new way to treat the condition. This project reports the product development of a polymer drug matrix with …

Hollow Plume Mitigation Of A High-Efficiency Multistage Plasma Thruster, Scott Alan Mcgrail

Master's Theses

Since 2000, a relatively new electric thruster concept has been in research, development, and production at Thales Electron Devices in Germany. This High Efficiency Multistage Plasma Thruster, or HEMPT, has promising lifetime capabilities due to its plasma confinement system. However, the permanent magnet system that offers this and other benefits also creates a hollow plume, where ions are accelerated at angles rather than up the thruster centerline, causing a dip in ion current along the centerline. A laboratory model, built at JPL, was run at Cal Poly to characterize this plume shape and implement a shield to restore a conical …

Investigation Into The Mitigation Of The Effects Of Uncertain Optical Degradation On An Interplanetary Solar Sail Mission Using A Single Model Update, Jordan Smiroldo

Master's Theses

The renewed academic interest in using solar sails as a source of spacecraft propulsion has been accompanied by a recent fervor of investigations into non-ideal and off-nominal sail performance considerations. One of the most influential considerations, uncertain optical degradation, has been shown to present significant trajectory design difficulties. This paper investigates the potential of using a mid-course degradation model update to mitigate the risk of missing the target destination in a sample 300 day Earth-Venus trajectory. Using a range of potential degradation profiles, it is shown that correcting in the first half of the mission is highly likely to result …

Effects Of Waste Placement Practices On The Engineering Response Of Municipal Solid Waste, Jason Taylor Cox

Master's Theses

An extensive laboratory and field investigation was conducted at Santa Maria Regional Landfill (SMRL) in Santa Maria, CA to determine the effects of waste placement practices on the engineering response of municipal solid waste (MSW). Laboratory and field testing was used to determine the engineering properties and monitor field response of MSW.

The specific gravity (G_s) of manufactured MSW (MMSW), fresh MSW (FMSW), and old MSW (OMSW) was determined experimentally using a modified version of standard soil testing procedures. Effects of particle size, compactive effort, and degradation on the specific gravity of waste were evaluated. Specific gravity …

Numerical Flow Field Analysis Of An Air Augmented Rocket Using The Axisymmetric Method Of Characteristics, Jeffrey Massman

Master's Theses

An Axisymmetric Rocket Ejector Simulation (ARES) was developed to numerically analyze various configurations of an air augmented rocket. Primary and secondary flow field visualizations are presented and performance predictions are tabulated. A parametric study on ejector geometry is obtained following a validation of the flow fields and performance values.

The primary flow is calculated using a quasi-2D, irrotational Method of Characteristics and the secondary flow is found using isentropic relations. Primary calculations begin at the throat and extend through the nozzle to the location of the first Mach Disk. Combustion properties are tabulated before analysis to allow for propellant property …

Cae Methods On Vibration-Based Health Monitoring Of Power Transmission Systems, Brian Fang

Master's Theses

This thesis focuses on different methods to analyze power transmission systems with computer software to aid in detection of faulty or damaged systems. It is split into three sections. The first section involves utilizing finite element software to analyze gear stiffness and stresses. A quasi-static and dynamic analysis are done on two sets of fixed axis spur gears and a planetary gear system using ABAQUS to analyze the stress, strain and gear mesh stiffness variation. In the second section, the vibrational patterns produced by a simple bevel gear system are investigated by an experiment and by dynamic modeling in ADAMS. …

Mechanical Properties Of Bone Due To Sost Expression: Nanoindentation Assessment Of Murine Femurs, Amir Rafie

Master's Theses

In the human genome, the SOST gene codes for a protein sclerostin. Sclerostin is an osteocyte-expressed negative regulator of bone formation. When the SOST gene is not coded, bone formation is reduced in individuals during skeletal maturation. This study utilizes nanoindentation methods to test for the mechanical properties of bones that both express and do not express the SOST gene. 100 transgenic murine femurs were obtained from Lawrence Livermore Labs in the form of 6 and 8 month SOST transgenic mice, 6 and 12 month SOST knockout mice, and wild type control littermates for each of the 4 age groups. …

Parsing Of Natural Language Requirements, Jamie L. Patterson

Master's Theses

The purpose of this thesis was to automate verification of the software requirements for an implantable cardioverter defibrillator with minimal manual rework. The requirements were written in plain English with only loose stylistic constraints. While full automation proved infeasible, many significant advances were made towards solving the problem, including a framework for storing requirements, a program which translates most of the natural language requirements into the framework, and a novel approach to parts of speech analysis.

Scale Model Shake Table Testing Of Seismic Earth Pressures In Soft Clay, Ron Edward Noche

Master's Theses

This research consists of scale model shake table tests to investigate the development of seismic earth pressures in soft clay. The soft clay was modeled after prototype San Francisco Bay Mud consisting of a mixture of kaolinite, bentonite, class C fly ash and water. A flexible walled testing container founded on a 1g shake table was used to house the model soil and mimic 1D site response. An array of accelerometers embedded in the model soil measure during an input earthquake motion.

A scale model wall is equipped with pressure sensors to measure the seismic earth pressures over the duration …

Investigation Of Compressed Air Energy Storage Efficiency, James W. Keeney

Master's Theses

This study investigates Compressed Air Energy Storage (CAES) application in the

electrical power and transportation industries. Information concerning current CAES projects is

presented. A thorough thermodynamic analysis of the CAES process is completed; including

theoretical efficiency determination for several variants of the compression and expansion

processes. Industry claimed efficiencies ranging from 26% to 82% are presented and explained.

Isothermal and Isentropic efficiency baselines are developed. Energy density of compressed air

on both a mass and volume basis is compared to other energy storage methods. Best expected

efficiency of a hypothetical CAES system is determined to be 34% using currently achievable …

Artist-Driven Fracturing Of Polyhedral Surface Meshes, Tyler Casella

Master's Theses

This paper presents a robust and artist driven method for fracturing a surface polyhedral mesh via fracture maps. A fracture map is an undirected simple graph with nodes representing positions in UV-space and fracture lines along the surface of a mesh. Fracture maps allow artists to concisely and rapidly define, edit, and apply fracture patterns onto the surface of their mesh.

The method projects a fracture map onto a polyhedral surface and splits its triangles accordingly. The polyhedral mesh is then segmented based on fracture lines to produce a set of independent surfaces called fracture components, containing the visible surface …

Mode I Fracture Toughness Of Eight-Harness-Satin Carbon Cloth Weaves For Co-Cured And Post-Bonded Laminates, Josh E. Smith

Master's Theses

Mode I interlaminar fracture of 3k 8-Harness-Satin Carbon cloth, with identical fill and weft yarns, pre-impregnated with Newport 307 resin was investigated through the DCB test (ASTM D5528). Crack propagations along both the fill and weft yarns were considered for both post-bonded (co-bonded) and co-cured laminates. A patent-pending delamination insertion method was compared to the standard Teflon film option to assess its applicability to mode I fracture testing. The Modified Beam Theory, Compliance Calibration method, and Modified Compliance Calibration method were used for comparative purposes for these investigations and to evaluate the validity of the proposed Equivalent Stiffness (EQS) method. …

Light Curve Generation For Satellites In Geostationary Orbits, Kimberly Andersen

Aerospace Engineering

This research were conducted at California Polytechnic State University San Luis Obispo throughout the Winter, Spring, and Fall quarters of 2013. The data presented in this paper was taken on the night of October 20, 2013 at the Cal Poly San Luis Obispo Astronomical Observatory and was reduced using IRAF software available on campus. This report describes the results of an observation of two bright XM geostationary satellites and the steps taken to get to those results. The average magnitude values of the XM-1 and XM-2 satellites were 13.753±0.007 and 14.015±0.007 respectively. The magnitude varied an average of 0.1 magnitudes …

Modification Of A Low Cost Vacuum Chamber For Use With An Electromagnetic Railgun, Jason M. Bertels

Aerospace Engineering

This report details the design and manufacture of modifications to a low cost vacuum chamber intended for railgun operations. These modifications intend to increase the functionality of the chamber and enable the modeling of high velocity impacts in a space. The original vacuum chamber was constructed primarily from polyvinyl chloride to meet the low cost design constraints, which limits pressures obtainable to the low vacuum region (760 Torr to 2 Torr). Modifications include construction of a space-saving storage rack, replacement of external door supports, installation of an internal guide rail, and installation of electrical feedthroughs.

Digital Control Board For Phased Array Antenna Beam Steering In Adaptive Communication Applications, Mayur Bansal

Master's Theses

The application of adaptive communication techniques for mobile communications has attracted considerable interest in the last decade. One example of these techniques is spatial filtering through planar antenna array beam forming.

This thesis describes the development of a digital system that adaptively controls a phased array antenna. The radiating structure of the phased antenna array is tetrahedral-shaped and contains four antenna elements on each of its three faces. The overall system comprises of a digital control board with an external computer interface, an RF control board, and the phased antenna array. The RF controls the main lobe direction on the …

Twelve Days Of Christmas Mechatronic Display, Michael Beltran, Christine Hagerman, Katie Ruhm

Mechanical Engineering

No abstract provided.

A Finite Element Model Based On Coupled Refined High-Order Global-Local Theory For Static Analysis Of Electromechanical Embedded Shear-Mode Piezoelectric Sandwich Composite Beams With Various Widths, S.B. Beheshti-Aval, S. Shahvaghar-Asl, M. Lezgy-Nazargah, Mohammad N. Noori

Mechanical Engineering

In this study, a new theory for the accurate simulation of the shear-mode behaviour of thin or thick piezoelectric sandwich composite beams is developed. The effects of transverse normal stress and transverse flexibility of layers are considered in the development of the proposed formulation. In order to increase the computational accuracy, all kinematic and stress continuity conditions are satisfied at layer interfaces. Moreover, for the first time, both the electrically induced strain components and the transverse flexibility are taken into account in the proposed formulation. Despite the fact that the number of unknown mechanical parameters in this theory is only …

Approximating The Seismic Amplification Effects Experienced By Solar Towers Mounted On The Rooftops Of Low-Rise Industrial Buildings, Peter Luiz Balla

Master's Theses

This thesis investigates the acceleration amplification experienced by solar towers mounted on the rooftops of low-rise industrial buildings during a seismic event. Specifically, this thesis looks to assess the validity of using amplification factors adopted by the ASCE 7-05Minimum Design Loads for Buildings and Other Structures to approximate seismic acceleration amplification for roof-mounted solar towers. To investigate the validity of the ASCE 7-05 amplification factors, this thesis conducts timehistory analyses of three theoretical solar towers mounted on the roof of a case study building. The time history analyses are conducted in the finite element computer modeling program SAP 2000 using …

Design And Implementation Of Eight-Legged Robotic Transporter, Jeremy David Depangher

Master's Theses

This thesis contains the design, manufacturing, and testing of a functional eight-legged robotic transporter based on the concept design laid out in U.S. Patent 7,246,671. The device is intended to achieve three different sequences of motion: regular driving, obstacle climbing, and stair climbing. The prototype was carried through concept design, analysis, selection of materials and components, manufacturing, software development, and final assembly and testing. The device can be assembled under multiple configurations, which harbor certain advantages and disadvantages. The results of the testing encourage the continuation of a second iteration of this concept.

Computational And Experimental Comparison Of A Powered Lift, Upper Surface Blowing Configuration, Jay M. Marcos

Master's Theses

In the past, 2D CFD analysis of Circulation Control technology have shown poor comparison with experimental results. In Circulation Control experiments, typical results show a relationship between lift coefficient, CL, vs blowing momentum coefficient, Cμ. CFD analysis tend to over-predict values of CL due to gridding issues and/or turbulence model selection. This thesis attempted to address both issues by performing Richardson’s Extrpolation method to determine an acceptable mesh size and by using FLUENT’s 2-equation turbulence models. The experimental results and CAD geometry were obtained from Georgia Tech Research Institute for comparison with the CFD analysis.

The study showed that 3D …

Robotic Fingerspelling Hand For The Deaf-Blind, Jerry Vin

Master's Theses

Because communication has always been difficult for people who are deaf-blind, The Smith-Kettlewell Eye Research Institute (SKERI), in conjunction with the California Polytechnic State University Mechanical Engineering department, has commissioned the design, construction, testing, and programming of a robotic hand capable of performing basic fingerspelling to help bridge the communication gap. The hand parts were modeled using SolidWorks and fabricated using an Objet rapid prototyper. Its fingers are actuated by 11 Maxon motors, and its wrist is actuated by 2 Hitec servo motors. The motors are controlled by Texas Instruments L293D motor driver chips, ATtiny2313 slave microcontroller chips programmed to …

Grass Referenced Based Vegetation Coefficients For Estimating Evapostranspiration For A Variery Of Natural Vegetation, Daniel J. Howes, Mariana Pasquet

BioResource and Agricultural Engineering

In arid and semi-arid regions, evapotranspiration from vegetation results in the significant utilization of available water. Accurate estimates of evapotranspiration are required for surface and subsurface hydrologic evaluations as well as irrigation district water balance studies. A significant amount of transferable information exists for irrigated agricultural crops through past and current research in the form of grass or alfalfa reference based crop coefficients (Kc) and basal crop coefficients (Kcb). However, transferable evapotranspiration information on natural vegetation is limited. Much of the work was conducted in the early to mid-1900’s and is presented as actual evapotranspiration from the vegetation at the …

Soil Nutrient Availability Properties Of Biochar, Nicole C. Esposito

Master's Theses

Biochar’s high porosity and negative surface charge allows for numerous soil and plant benefits such as increased water retention, high nutrient availability, and plant growth. By analysing biochar’s effect of all of these factors, a system can be put in place in which soils can be remediated with the proper soil amendments. This report discusses and tests the effects of varying rates of biochar on pH levels, cation exchange capacity, and nutrient exchangeability (of calcium, magnesium, sodium, and potassium) in soil. Corn plants were also grown in soils of varying amendment types and analysed for plant growth and germination to …

Veryifying Liquefaction Remediation Beneath And Earth Dam Using Spt And Cpt Based Methods, Ikram Guettaya, Mohamed Ridha El Ouni, Robb Moss

Civil and Environmental Engineering

This paper presents a case study of liquefaction potential assessment for the foundation of an earth dam in Tunisia. An emphasis was made on the exploration of geotechnical conditions and the interpretation of field tests (SPT and CPT) and the results were collected before and after soil densification using the vibrocompaction technique. The assessment of soil liquefaction triggering was made using deterministic and probabilistic simplified procedures. The results indicate that before vibrocompaction the studied area was prone to the liquefaction hazard. However, after vibrocompaction a significant improvement of the soil resistance reduced the liquefaction potential of the sandy foundation soil. …

Development Of Numerical Model For Predicting Heat Generation And Temperatures In Msw Landfills, James L. Hanson, Nazli Yesiller, Michael T. Onnen, Wei-Lien Liu, Nicolas K. Oettle, Janelle A. Marinos

Civil and Environmental Engineering

A numerical modeling approach has been developed for predicting temperatures in municipal solid waste landfills. Model formulation and details of boundary conditions are described. Model performance was evaluated using field data from a landfill in Michigan, USA. The numerical approach was based on finite element analysis incorporating transient conductive heat transfer. Heat generation functions representing decomposition of wastes were empirically developed and incorporated to the formulation. Thermal properties of materials were determined using experimental testing, field observations, and data reported in literature. The boundary conditions consisted of seasonal temperature cycles at the ground surface and constant temperatures at the far-field …

Attitude Estimation For A Gravity Gradient Momentum Biased Nanosatellite, Arash Mehrparvar

Master's Theses

Attitude determination and estimation algorithms are developed and implemented in simulation for the Exocube satellite currently under development by PolySat at Cal Poly. A mission requirement of ±5˚ of attitude knowledge has been flowed down from the NASA Goddard developed payload, and this requirement is to be met with a basic sensor suite and the appropriate algorithms. The algorithms selected in this work are TRIAD and an Extended Kalman Filter, both of which are placed in a simulation structure along with models for orbit propagation, spacecraft kinematics and dynamics, and sensor and reference vector models. Errors inherent from sensors, orbit …

Bayesian Approach For Uncertainty Analysis Of An Urban Storm Water Model And Its Applications To A Heavily Urbanized Watershed, Misgana K. Muleta, Jonathan Mcmillan, Geremew G. Amenu, Steven J. Burian

Civil and Environmental Engineering

The significance of uncertainty analysis (UA) to quantify reliability of model simulations is being recognized. Consequently, literature on parameter and predictive uncertainty assessment of water resources models has been rising. Applications dealing with urban drainage systems are, however, very limited. This study applies formal Bayesian approach for uncertainty analysis of a widely used storm water management model and illustrates the methodology using a highly urbanized watershed in the Los Angeles Basin, California. A flexible likelihood function that accommodates heteroscedasticity, non-normality, and temporal correlation of model residuals has been used for the study along with a Markov-chain Monte Carlo-based sampling scheme. …