Engineering Commons^™

Hall Effect Modeling In Fem Simulators And Comparison To Experimental Results In Silicon And Printed Sensors, Leonardo A. Frem

Master's Theses

Finite element method simulation models for thin-film semiconductor-based Hall sensors were developed using secondary data in order to understand their behavior under strong magnetic fields. Given a device geometry and charge carrier density and mobility, the models accurately calculated sensor resistance, Hall voltage under a normally-incident constant magnetic field, and expected offset from a population of Hall devices. The model was successfully matched against data from integrated chip Hall sensors from St. Jude Medical. Additionally, the feasibility of creating Hall effect devices with common carbon ink was explored experimentally. The material properties obtained from testing these ink-based devices through the …

Design And Testing Of A Top Mask Projection Ceramic Stereolithography System For Ceramic Part Manufacturing, Dylan Robert De Caussin

Master's Theses

Ceramic manufacturing is an expensive process with long lead times between

the initial design and final manufactured part. This limits the use of ceramic as a viable material unless there is a large project budget or high production volume associated with the part. Ceramic stereolithography is an alternative to producing low cost parts through the mixing of a photo curable resin and ceramic particles. This is an additive manufacturing process in which each layer is built upon the previous to produce a green body that can be sintered for a fully dense ceramic part.

This thesis introduces a new approach …

The Effects Of Obesity On Resultant Knee Joint Loads For Gait And Cycling, Juan Gutierrez-Franco

Master's Theses

Osteoarthritis (OA) is a degenerative disease of cartilage and bone tissue and the most common form of arthritis, accounting for US$ 10.5 billion in hospital charges in 2006. Obesity (OB) has been linked to increased risk of developing knee OA due to increased knee joint loads and varus-valgus misalignment. Walking is recommended as a weight-loss activity but it may increase risk of knee OA as OB gait increases knee loads. Cycling has been proposed as an alternative weight-loss measure, however, lack of studies comparing normal weight (NW) and OB subjects in cycling and gait hinder identification of exercises that may …

Characterizing Neurotransmitter Receptor Activation With A Perturbation Based Decomposition Method, Stephen Gregory Jue

Master's Theses

The characterization of postsynaptic potentials, in terms of neurotransmitter receptor activation, is of clinical significance because information associated with receptor activation can be used in the diagnosis and study of neurological disorders. Single-unit recordings provide a method of measuring postsynaptic potentials in neurons using a microelectrode system, but yield no detailed information regarding the neurotransmitter receptors that contribute to the potential. To determine the types of neurotransmitter receptors that result in a compound postsynaptic potential from a microelectrode reading, decomposition of the potential is necessary. In this work, a perturbation-based decomposition method developed by R. Szlavik is evaluated for this …

Analysis Of Various Algorithmic Approaches To Software-Based 1200 Baud Audio Frequency Shift Keying Demodulation For Aprs, Robert F. Campbell

Master's Theses

Digital communications continues to be a relevant Field of study as new technologies appear and old methodologies get revisited or renovated. The goal of this research is to look into the old digital communication scheme of Bell 202 [67] used by APRS and improve software based demodulation performance. Improved performance is defined by being able to correctly decode more packets in an efficient, real time, manner. Most APRS demodulation is currently done using specialized hardware since that yields the best performance. This research shows that through using Sivan Toledo's javAX25 [72] software package, new demodulation algorithms can be implemented that …

Processing Of Simulated And Experimental Images Of Closely Spaced Binary Stars Using Speckle Interferometry, Niels Smidth

Master's Theses

Theory and methods of processing speckle interferometry data from close visual binary stars are presented and implemented. The effects of the optical systems used for observing close visual binary stars are explained and simulated from both the geometrical and physical optical viewpoints. The atmospheric phase distortion and shot noise responsible for the observed speckle patterns are simulated. The deconvolution technique originally presented by Labeyrie is implemented to extract astrometric data from close visual binary stars. This method is applied to both simulated and experimental data from Kitt Peak National Observatory as validation. Parts of the deconvolution process are optimized to …

Benefits Of Advanced Traffic Management Solutions: Before And After Crash Analysis For Deployment Of A Variable Advisory Speed Limit System, Alexander Lindsay Chambers

Master's Theses

Variable speed limit (VSL) systems are important active traffic management tools that are being deployed across the U.S. and indeed around the world for relieving congestion and improving safety. Oregon’s first variable advisory speed limit signs were activated along Oregon Highway 217 in the summer of 2014. The variable advisory speed system is responsive to both congestion and weather conditions. This seven-mile corridor stretches around Western Portland and has suffered from high crash rates and peak period congestion in the past. VSL systems are often deployed to address safety, mobility and sustainability related performance. This research seeks to determine whether …

Wavelength Accuracy Study For High-Density Fiber Bragg Grating Sensor Systems Using A Rapidly-Swept Akinetic-Laser Source, Jacob Egorov

Master's Theses

This thesis studies the center wavelength accuracy of a Fiber Bragg Grating Sensor system that has a large number of sensor elements both as a function of wavelength and as a function of position. Determining the center wavelength of each of the fiber optic sensors is a critical parameter that ultimately determines sensor accuracy. The high density environment can result in degradation of accuracy of the center wavelength measurement. This thesis aims to quantify this measurement error both with theoretical and experimental studies.

There are many sensing applications where optical fiber sensors are preferred over electrical sensors, such as the …

Incorporating Histograms Of Oriented Gradients Into Monte Carlo Localization, Michael K. Norris

Master's Theses

This work presents improvements to Monte Carlo Localization (MCL) for a mobile robot using computer vision. Solutions to the localization problem aim to provide fine resolution on location approximation, and also be resistant to changes in the environment. One such environment change is the kidnapped/teleported robot problem, where a robot is suddenly transported to a new location and must re-localize. The standard method of "Augmented MCL" uses particle filtering combined with addition of random particles under certain conditions to solve the kidnapped robot problem. This solution is robust, but not always fast. This work combines Histogram of Oriented Gradients (HOG) …

Prosthetic Leg Kit For Deployment In Developing Countries, Brian Murphy, Dominique Porcincula, Derek Morgan, Kendall Ruggles, Christian Aguayo

Biomedical Engineering

The World Health Organization estimates that over 30 million people require some sort of prosthetic technology. However, traditional prosthetic fitting practices take a lot of time and cost a lot of money, making them inaccessible to millions of people around the world. StandUP Worldwide is an interdisciplinary project team devoted to creating low-cost prosthetic technologies for use around the world, especially in resource poor areas. They are currently developing a low cost, below-the-knee prosthetic kit that can be easily deployed in a resource-poor area. The following presents their solution for a below-the-knee prosthetic socket, foot, and leg.

Campusbookshare, Aditya Varkhedi

Computer Science and Software Engineering

Every few months, students in the US and abroad face the expensive and time consuming task of buying textbooks for the classes they are enrolled in. Despite the advent of the internet and social networking websites the ability for peer to peer textbook exchange is still limited. There are few if any dedicated websites for general purpose peer to peer textbook transfer for every university and college.

The project I have created for my Senior Project is a peer to peer solution for buying and selling textbooks on US college campuses. The underlying idea is to create an authentication system …

Deontological Ethical System For Google's Self-Driving Car, Edgard Alejandro Arroliga Jr.

Computer Science and Software Engineering

Google's Self-Driving Car is a revolutionary product that is riddled with ethical conundrums. It is able to accurately scan and drive through densely populated roads without much difficulty. However, there are some situations where the car will likely have to make decisions that affect, maybe even take, the lives of those on the road. Issues such as the Trolley Problem and the Rear-End Dilemma describe situations where there seems to be no single ethical answer as to how the car should act. In order to solve these issues, I propose that a Deontological Ethical System should be implemented because it …

Usb-Powered Turntable "Turn T", Gerardo Sevilla, James Lougaris

Electrical Engineering

No abstract provided.

Design Of A Folding V-Scraper With Roller For Orchard Applications, Chase Ulrich

BioResource and Agricultural Engineering

This senior project discusses the design of a folding 15 ft. wide leveler for orchard use. This design utilized a category 2 three-point hitch to connect the implement to a tractor. The folding mechanism uses the tractors hydraulic system to actuate the folding movement using hydraulic cylinders. The blades, when wings in operational position, are rigid with one another after some assembly. When the implement is folded the width is reduced to nine feet.

Design, Construction, And Evaluation Of Off-Road Rock Sliders, Jake M. Freedman

BioResource and Agricultural Engineering

This senior project describes the design, fabrication, and evaluation of off-road rock sliders which can be used with Toyota Tacoma trucks of model year 2005-2012. Rock sliders are a form of trail armor and are a common aftermarket addition to trucks that are often used in off-road conditions. Rock sliders, in their simplest form, consist of a steel beam (either tubular or rectangular) that runs underneath the doors of the vehicle providing protection to the undercarriage, rocker panels, and doors as well as reducing the likelihood of becoming stuck or “high-centered” on the underside of the vehicle. The sliders will …

Solar-Powered Hot Tub, Jonathan Peterson, Anthony Zepeda

Electrical Engineering

This paper discusses the design and implementation of a solar-powered hot tub. The concept of this project was to design an independently-operated hot tub powered by a 12V rechargeable battery, charged during the day by a single 400W solar panel. For this purpose, a twenty-year-old name-brand hot tub was purchased, in used condition. The plumbing, AC electrical wiring, and mechanical pumps were all removed and replaced with new components to meet our design specifications. Additionally, a solar water-heater was designed and integrated into the system to directly apply the sun’s heat to water pumped in and out of the tub, …

Bbq Grill Temperature Uniformity Study, Monty Dodge Jr, Samuel Melo

Mechanical Engineering

Bull Outdoor Products, Incorporated, a barbeque grill and outdoor kitchen manufacturer, sponsored this project with the intent of improving the temperature uniformity across the surface of their barbecue grills. For this project, the Cal Poly team of mechanical engineering students, Monty Dodge Jr. and Samuel Melo, used the Brahma grill head model with setups for both natural gas and propane. In order to determine exactly what the uniformity across the grill surface was, the student team designed a testing apparatus which would measure a grid of temperature locations one inch apart spanning an area 16 by 36 inches. Developing a …

Ism S-Band Cubesat Radio Designed For The Polysat System Board, Craig Lee Francis

Master's Theses

Cal Poly’s PolySat CubeSat satellites have begun to conduct more complex and scientifically significant experiments. The large data products generated by these missions demonstrate the necessity for higher data rate communication than currently provided by the PolySat UHF radio. This thesis leverages the proliferation of consumer wireless monolithic transceivers to develop a 250kbps to 2000kbps, 2W CubeSat radio operating within the 2.45GHz Industrial, Scientific, and Medical (ISM) radio band.

Estimating a link budget for a realistic CubeSat leads to the conclusion that this system will require a large deployable CubeSat antenna, large earth station satellite dish, and a fine-pointing attitude …

Optimization Of Rfid System Coverage In A Manufacturing Environment, Scott D. Malatesta

Master's Theses

This paper compiles existing ideas, theories, and experiments across multiple disciplines to provide guidance for a company looking to implement an optimal RFID system in their production facility. The desire is to maximize the information received by the system while minimizing the cost. Four potential layouts of RFID antennas, two with overlapping antenna coverage and two with non-overlapping layouts, are first analyzed to understand the special coverage and the number of antennas required. The value of information is then quantified to determine whether higher coverage layouts are worth the additional costs associated with the higher number of antennas required. It …

Instructables.Com As A Tool To Improve Student Outcomes And Promote Community Engagement (Work-In-Progress), Andrew Danowitz

Electrical Engineering

Project-based Learning (PBL) has become a popular pedagogical tool in Engineering. Projects force students to put theory learned in lecture into practice, exposes students to some of the nonidealities of real systems (imperfect instruments, uncooperative systems, etc.) that are difficult to convey in lecture or homework, and ideally motivates students by showing how course material is related real-world engineering problems. This work discusses my preliminary and ongoing research into using Instructables.com—a user-content generated website of “Do It Yourself” tutorials—as a tool to help amplify the benefits students derive from PBL. Specifically, I require students to document their projects in an …

Mapping Quality In Extended Value Streams Using Data Recorders, Eric Olsen, Christopher Fung, Jay Singh, Paul Singh

Industrial Technology and Packaging

This research compares three new methods and measures for mapping and evaluating the transportation segment of a value chain. The three methods are total energy, energy-time and energy-distance. The methods combine practices used in traditional physical distribution system analysis and extended value stream mapping (VSM) analysis. This research concludes that the energy-distance method and measure is the most effective for analyzing, comparing, and identifying opportunities for value chain improvement. It also identifies a ‘U-shape’ that is characteristic of the energy transfer pattern during a transportation segment that suggests that damage from transportation may need to be screened for quality at …

Densification Of W-Ni-Fe Powders Using Laser Sintering, Xuan Wang, Matthew Wraith, Stephen Burke, Howard Rathbun, Kyle Devlugt

Industrial and Manufacturing Engineering

In this paper, Laser Sintering (LS) of 90%W–7%Ni–3%Fe (wt.%) powders have been investigated, with the goal to understand the influence of final density by laser power, scanning speed, laser trace width, and the number of scanning passes. The results suggest that the laser power and scanning speed are the most important factors influencing density; the influence of trace width and number of scanning passes are not significant. With the increase of laser power and decrease of scanning speed, higher density can be achieved. The microstructure analysis indicated that the porosity changed from open porosity to closed porosity with higher laser …

Effects Of Curing Cycle And Loading Rates On The Bearing Stress Of Double Shear Composite Joints, Mateja Andrejic

Master's Theses

In the last few decades, there has been a shift to using more lightweight materials for the potential of fuel consumption reduction. In the Aerospace Industry, conventional metal structures are being replaced by advanced composite structures. The major advantage of an advanced composite structure is the huge reduction in the number of parts and joints required. Also composite materials provide better resistance to creep, corrosion, and fatigue. However, one cannot eliminate all the joints and attachments in an aircraft’s structure. Eliminating structural joints is impractical in present-day aircraft because of the requirements for inspection, manufacturing breaks, assembly and equipment access, …

Multi-Level Analytic Network Process Model To Mitigate Supply Chain Disruptions In Disaster Recovery Planning, Martina Ursula Kroener

Master's Theses

Over the past few decades, environmental changes have led to more frequent occurrences and greater intensities of natural disasters worldwide. In terms of globally connected supply chains, this has resulted in an enormous economical loss for corporations. Therefore, Business Continuity and Disaster Recovery (BC/DR) planning and management has become essential for businesses in order to protect their critical business flow. Yet there is a lack of systematic and transparent methodologies for companies to handle this problem.

Hence, this thesis introduces a novel approach to combine consecutive steps of the Disaster Recovery Planning (DRP) process within one application. The multi-criteria decision-making …

Skycsr: Optimal Communication Methods For Coordinating Ground Support In A Private And General Aviation Setting, Jessica Burke

Industrial and Manufacturing Engineering

Delays due to miscommunication of between the pilot and ground service providers are increasing. The objective of this project is to develop a new method of communication between pilots, line service technicians and customer service agents. This will be achieved first through an investigation into current methods and state of the industry, followed by a survey conducted with a group of pilots and flight schools. This culminates in a web application that will take the deficiencies identified in the survey, to make sure ground service or fuel orders are explicitly clear and minimize the probability of a mis-fueling, overlooked fueling, …

Carbon Emission Awareness And Information Platform, Jose Ignacio Cordero, Paul Romero

Industrial and Manufacturing Engineering

Climate change due to global warming has become a worldwide concern.

Nowadays, people are starting to wake up and realize that changes need to be

made in their lifestyles in order to preserve this earth and provide a better planet

for future generations. Finding a concrete solution to global warming and climate

change has proven to be a very challenging task. Governments have tried

implementing solutions and as a result, corporations have been forced to absorb

or transfer the cost of unsuccessful environmental regulations. Meanwhile,

individuals remain frustrated, wishing they could find a way to help.

The motivation behind this …

Multi-Level Route-Optimization Computer Application, Ryan Sutardji, Frank Nguyen

Industrial and Manufacturing Engineering

This report provides a detailed analysis on how to optimize driving routes by creating a computer application. There are many different route-optimization issues that logistical companies consistently face, as well as many different solutions and algorithms. With technology on the rise, pick-up, delivery, and transportation services are become a huge part of our everyday lives. When optimizing routes, reducing transportation costs by minimizing travel distance is always ideal, but other factors must be considered such as arriving at a location before or after a certain time. Our objective is to optimize driving routes based on travel distance and priorities. We …

Multi-Axis Machining Project Development, Ryan Patrick Blodgett, Andre Peter Rivera

Industrial and Manufacturing Engineering

Multi-axis milling is a manufacturing material removal process in which computer numerically controlled (CNC) tools cut away excess material through movement in four or more axes. Compared to traditional three-axis machining, multi-axis machining greatly increases the capability and accuracy of the CNC machining processes by reducing the amount of operations required to completely machine a part. Currently, the Industrial and Manufacturing Engineering Department at Cal Poly lacks an advanced CNC class that incorporates fourth and fifth axis CNC machining in the curriculum. This report describes the process behind creating a project for such a class. The class will demonstrate the …

Fire And Life Safety Analysis Of Cal Poly Engineering Iv, Business In Amarillo, Tx And Costco, Russell B. Bainbridge Iii

Fire Protection Engineering: Culminating Experience Project Reports

The main fire protection disciplines ‐ Egress Analysis and Design, Fire Detection, Alarm and Communication Systems, Water‐based Fire Suppression Systems and Structural Fire Protection ‐ are covered in this report.

For Egress Analysis and Design, the California Polytechnic State University’s Engineering IV building was analyzed and covered in the first portion of this report. The building was analyzed against the 2015 edition of NFPA 101 and the 2015 edition of the International Building Code. It is a typical university engineering building with classrooms, professors’ offices and some laboratories. The occupancies, the occupant load, exit widths, exit lengths and number of …

Maintenance Shop Building- Comprehensive Fire Protection Evaluation, Theodore P. Stanton

Fire Protection Engineering: Culminating Experience Project Reports

The purpose of this report is to analyze the fire protection systems and features of the Maintenance Shop Building (MSB), which is a two story office and training building on the campus of a large industrial facility in central California. The goal of the fire protection systems and features of the Building is to provide occupants with reasonable assurance of safety from fire. This goal can be met by ensuring that occupants not intimate with the initiation of a fire will be able to safely escape from the Building in the event of the fire.

The ability of the MSB’s …