Engineering Commons^™

Solution Of Nonlinear Transient Heat Transfer Problems, Donovan O. Buckley

FIU Electronic Theses and Dissertations

In the presented thesis work, meshfree method with distance fields was extended to obtain solution of nonlinear transient heat transfer problems. The thesis work involved development and implementation of numerical algorithms, data structure, and software. Numerical and computational properties of the meshfree method with distance fields were investigated. Convergence and accuracy of the methodology was validated by analytical solutions, and solutions produced by commercial FEM software (ANSYS 12.1). The research was focused on nonlinearities caused by temperature-dependent thermal conductivity. The behavior of the developed numerical algorithms was observed for both weak and strong temperature-dependency of thermal conductivity. Oseen and Newton-Kantorovich …

Can Segmented Flow Enhance Heat Transfer In Microchannel Heat Sinks?, Amy Rachel Betz, Daniel Attinger

Daniel Attinger

Liquid cooling is an efficient way to remove heat fluxes with magnitudes up to 10,000 W/cm2. One limitation of current single-phase microchannel heat sinks is the relatively low Nusselt number, due to laminar flow. In this work, we experimentally investigate how to enhance the Nusselt number with the introduction of segmented flow. The segmented flow pattern was created by the periodic injection of air bubbles through a T-junction into water-filled channels. We designed a polycarbonate heat sink consisting of an array of seven parallel microchannels each with a square cross-section 500 μm wide. We show that segmented flow increases the …

Flow Loop Simulator, Tyler Ista, Kevin Rehm, Matt Starbuck

Mechanical Engineering

PG&E’s Diablo Canyon Power Plant has requested a full-sized flow process system for training of technicians by providing them a hands-on experience in a controlled environment. The basic design requirements were established to determine the scope of the project. An initial system layout was selected from a variety of concepts after similar system schematics, components, and processes had been researched. The resulting schematic was flexible to suit several needs of the control aspect while remaining simple.

Design efforts resulted in a system capable of many configurations; allowing for implementation of three training experiments. These experiments involve control of tank level …

Steady-State Green’S Function Solution For Moving Media With Axial Conduction, A. Haji-Sheikh, J. V. Beck, Kevin D. Cole

Department of Mechanical and Materials Engineering: Faculty Publications

The objective of this presentation is the development of a generalized steady-state Green’s function solution to study the temperature field in moving bodies. This type of solution permits the inclusion of different nonhomogeneous boundary conditions, volumetric heat sources, and possible position-dependent thermophysical properties. Although the mathematical formulation is for moving solids, it can be used to study the heat transfer in a moving fluid with a non-uniform velocity distribution passing through a micro-channel or fluid-saturated porous ducts. Additionally, this presentation includes the application of this Green’s function solution to acquire numerical information for selected examples to further illustrate the numerical …

Experimental Investigation Of Flow And Heat Transfer Characteristics Of R -134a In Microchannels, Abdullahel Bari

Doctoral Dissertations

The purpose of this study was to investigate the flow and heat transfer characteristics of liquid refrigerant R-134a in rectangular microchannels. The research concentrated mostly upon single-phase experiments with limited investigation of boiling phenomenon in microchannels. Tests were performed using rectangular microchannels with hydraulic diameters ranging from 112 μm to 210 μm and aspect ratios varying approximately from 1.0 to 1.5. The Reynolds number in the experiments ranged from 1,200 to 13,000 although most data were collected in the transition and turbulent flow regimes.

The experimental data for friction factor measurement had a similar trend as predicted by macroscale theory …

Note: Thermal Analog To Atomic Force Microscopy Force-Displacement Measurements For Nanoscale Interfacial Contact Resistance, Brian D. Iverson, John E. Blendell, Suresh V. Garimella

Faculty Publications

Thermal diffusion measurements on polymethylmethacrylate-coated Si substrates using heated atomic force microscopy tips were performed to determine the contact resistance between an organic thin film and Si. The measurement methodology presented demonstrates how the thermal contrast signal obtained during a force-displacement ramp is used to quantify the resistance to heat transfer through an internal interface. The results also delineate the interrogation thickness beyond which thermal diffusion in the organic thin film is not affected appreciably by the underlying substrate.

Designing Of Energy Efficient Indoor Environments Using A Localized Radial Basis Function Meshless Method, Victor Huayamave

Electronic Theses and Dissertations

Around the world, the energy over consumption issue has been one of the key socio-economic and political challenges, which has drastically worsened over the last few years. Over the years engineers and environmentalists have proposed several approaches to improve energy efficiency. One is to reduce energy demand by improving consumption habits and a second approach is to introduce the use of a "greener" concept by using biomaterials in a diverse and more efficient manner in engineering construction to create energy efficient environments. This work will investigate the effects of using "green" stabilized earth materials to provide and enhance thermal regulation …

High Heat Flux Spray Cooling With Ammonia On Enhanced Surfaces, Huseyin Bostanci

Electronic Theses and Dissertations

Many critical applications today, in electronics, optics and aerospace fields, among others, demand advanced thermal management solutions for the acquisition of high heat loads they generate in order to operate reliably and efficiently. Current competing technologies for this challenging task include several single and two phase cooling options. When these cooling schemes are compared based on the high heat flux removal (100-1000 W/cm2) and isothermal operation (within several oC across the cooled device) aspects, as well as system mass, volume and power consumption, spray cooling appears to be the best choice. The current study focused on high heat flux spray …

A Model Integrated Meshless Solver (Mims) For Fluid Flow And Heat Transfer, Salvadore Gerace

Electronic Theses and Dissertations

Numerical methods for solving partial differential equations are commonplace in the engineering community and their popularity can be attributed to the rapid performance improvement of modern workstations and desktop computers. The ubiquity of computer technology has allowed all areas of engineering to have access to detailed thermal, stress, and fluid flow analysis packages capable of performing complex studies of current and future designs. The rapid pace of computer development, however, has begun to outstrip efforts to reduce analysis overhead. As such, most commercially available software packages are now limited by the human effort required to prepare, develop, and initialize the …

Thermal Analog To Afm Force-Displacement Measurements For Nanoscale Interfacial Contact Resistance, Brian D. Iverson, John E. Blendell, Suresh V. Garimella

Faculty Publications

Thermal diffusion measurements on PMMA-coated Si substrates using heated AFM tips were performed to determine the contact resistance between an organic thin film and Si. The measurement methodology presented demonstrates how the thermal contrast signal obtained during a force-displacement ramp is used to quantify the resistance to heat transfer through an internal interface. The results also delineate the interrogation thickness beyond which thermal diffusion in the organic thin film is not affected appreciably by the underlying substrate.