Engineering Commons^™

Modeling And Computation Of The Maximum Braking Energy Speed For Transport Category Airplanes, Nihad E. Daidzic

Journal of Aviation Technology and Engineering

Transport-category or FAR/CS 25 certified airplanes may occasionally become braking energy capacity limited. Such limitation may exist when heavy airplanes are departing airports at high-density altitudes, on relatively long runways, and/or possibly with some tailwind component. A maximum braking energy VMBE speed exists which may limit the maximum allowable takeoff decision/action speed V1. The ever-existing possibility of high-speed rejected takeoff in such conditions may also limit the airplane gross weight for declared available distances. To gain deeper insights and acquire better understanding of the topic, a theoretical model of the maximum braking energy and the related VMBE speed for T-category …

Application Of Ultrasound In The Measurement Of Lubricant Fluid Film Thickness In The Piston-Cylinder Interface Of An Axial Piston Pump, Dhruv Subramaniam, Dan Mizell, Monika Ivantysynova

The Summer Undergraduate Research Fellowship (SURF) Symposium

In this paper a feasibility study has been conducted to determine a technique for the measurement of lubricant fluid film thickness in the piston-cylinder interface of an axial piston pump. The thickness of the lubricant film has a significant impact on the efficiency of the piston pump yet it still remains an uncertainty. If the lubricant film is too thin then friction will cause excessive damage resulting in deformation of interacting surfaces resulting in further uncertainty in thickness measurement. If the lubricant film is too thick then there is excessive leakage which will compromise the efficiency of the system. Acoustic, …

Modeling Of Mixed Friction Interactions Occurring In Axial Piston Pumps, Andrew C. Adelsperger, Lizhi Shang, Dan Mizell, Monika Ivantysynova

The Summer Undergraduate Research Fellowship (SURF) Symposium

Axial piston pumps are integral to a variety of hydraulic systems due to their versatility and reliability, but most attempts to model them for design purposes have failed. However, software which fully models the fluid structures within these pumps, such as the FSTI gap design program, has improved significantly. Unfortunately, current discrepancies between simulated and measured friction forces on the cylinder due to the fluid drag and piston movement need to be eliminated so that more accurate simulation of these pumps in operation is possible. Friction measurements and FSTI simulation outputs were analyzed with MATLAB filters and graphs, resulting in …

Acoustic Emission Detection Of Metals And Alloys During Machining Operations, Jameson K. Nelson

Purdue Polytechnic Masters Theses

Nelson, Jameson K. M.S., Purdue University, May 2012. Acoustic Emission Detection of Metals and Alloys During Machining Operations. Major Professor: Rodney G. Handy.

Practical correlation between material deformation attributes and theoretical concepts of machining has proven difficult to attain. The purpose of this study was to further explore trends and relationships using acoustic emission detection of materials undergoing single-point lathe turning machine processes. The majority of machining experiments that incorporate acoustic emissions focuses on tool degradation for the purposes of optimizing consumables required to manufacture mechanical devices. Experiments were implemented varying recording location, mechanical barrier condition, and machine parameters. The …

Identification Of Multiple Oscillation States Of Carbon Nanotube Tipped Cantilevers Interacting With Surfaces In Dynamic Atomic Force Microscopy, Mark Strus, Arvind Raman

Birck and NCN Publications

Carbon nanotubes (CNTs) have gained increased interest in dynamic atomic force microscopy (dAFM) as sharp, flexible, conducting, nonreactive tips for high-resolution imaging, oxidation lithography, and electrostatic force microscopy. By means of theory and experiments we lay out a map of several distinct tapping mode AFM oscillation states for CNT tipped AFM cantilevers: namely, noncontact attractive regime oscillation, intermittent contact with CNT slipping or pinning, or permanent contact with the CNT in point or line contact with the surface while the cantilever oscillates with large amplitude. Each state represents fundamentally different origins of CNT-surface interactions, CNT tip-substrate dissipation, and phase contrast …