Engineering Commons^™

A Multiphase Modified Boost Converter With Reduced Input Current Ripple: Combined Capacitors, Omri Nissan

Master's Theses

The delivery of high power and smaller footprints through a non-isolated topology demands for the use of multiphase topology in DC-DC converters. Multiphase reduces the ripple observed on both the input and output waveforms; however, it may not be enough to connect to sensitive power sources such as renewable energy sources. A single-phase modified boost converter demonstrates the ability to acquire very minimal input current ripple by addition of passive components. The expansion to multiphase topology is the next logical step for higher power application while furthering the low input current ripple benefit. In this thesis, the multiphase modified boost …

Protection, Automation, And Frequency Stability Analysis Of A Laboratory Microgrid System, Christopher Eric Osborn

Master's Theses

Due to increasing changes in the power industry, Cal Poly San Luis Obispo's electrical engineering department introduced a set of initiatives to adequately equip students with the skills and knowledge to interact with new technologies. Specifically, the department proposed a microgrid and power systems protection and automation laboratory to strengthen students' knowledge of microprocessor-based relays. This paper outlines a microgrid laboratory system that fulfills the initiative's goal and proposes a collection of laboratory experiments for inclusion in a new laboratory course at Cal Poly. The experiments provide students with practical experience using Schweitzer Engineering Laboratory (SEL) relays and teach fundamental …

Protection Against Ungrounded Single Phase Open Circuit Faults In 3-Phase Distribution Transformers, Higinio Ariel Montoya

Master's Theses

This thesis explores the impacts and behavior of 3-phase distribution transformers when subject to ungrounded single phase open circuit faults. A simple 3-phase system is modeled using MATLAB Simulink and operation under fault conditions are simulated and studied. Simulation results are confirmed via lab experimentation. Finally, a robust detection and protection method using neutral current injection (as proposed in industry literature) is built and demonstrated.

Electric utility operating experience has demonstrated that all too often, loads on 3-phase distribution transformers are not adequately protected against an ungrounded single phase open circuit fault (commonly called “single phasing”). This type of fault …

A Modified Boost Converter With Reduced Input Current Ripple, Nathan H. Lentz

Master's Theses

Battery-powered trends in consumer electronics, transportation, and renewable energy sectors increase demands on DC/DC converter technology. Higher switching frequency and efficiency reduces solution size and cost, while increasing power capabilities. Still, switching noise remains the primary drawback associated with any DC/DC converter. Reducing a converter’s input ripple helps prevent switching noise from spreading to other systems on a shared DC power bus. This thesis covers the analysis, simulation, and implementation of a recently-proposed boost converter topology, alongside an equivalent standard boost converter, operating in steady-state, continuous conduction mode. A Matlab-based simulation predicts each converter’s input ripple performance using a state-space …

Design And Construction Of 1800w Modular Multiple Input Single Output Non-Isolated Dc-Dc Converters, Angelo Miguel Asuncion Gallardo

Master's Theses

This thesis report details the design and construction of non-isolated DC-DC converters to create a Multiple Input Single Output (MISO) converter for combining multiple renewable energy sources into one single output. This MISO uses the four-switch buck-boost topology to output a single 48V from multiple nominal 24V inputs. The MISO converter implements a modular approach to deliver 1800W output power. Each module in the MISO is rated at 600W and they share the output power equally. Hardware results show that the converter produces 1800W of output power from three sources with 96.4% efficiency. Each module also demonstrates equal sharing feature …

Dc-Dc Converter Control System For The Energy Harvesting From Exercise Machines System, Alexander Sireci

Master's Theses

Current exercise machines create resistance to motion and dissipate energy as heat. Some companies create ways to harness this energy, but not cost-effectively. The Energy Harvesting from Exercise Machines (EHFEM) project reduces the cost of harnessing the renewable energy. The system architecture includes the elliptical exercise machines outputting power to DC-DC converters, which then connects to the microinverters. All microinverter outputs tie together and then connect to the grid. The control system, placed around the DC-DC converters, quickly detects changes in current, and limits the current to prevent the DC-DC converters and microinverters from entering failure states.

An artificial neural …

Protective Relaying Student Laboratory, Kenan W. Pretzer

Master's Theses

Facing a rapidly-changing power industry, the electrical engineering department at Cal Poly San Luis Obispo proposed Advanced Power Systems Initiatives to better prepare its students for entering the power industry. These initiatives call for the creation of a new laboratory curriculum that uses microprocessor-based relays to reinforce the fundamental concepts of power system protection. This paper summarizes a laboratory system fit for this task and presents a set of proposed laboratory experiments to establish a new laboratory course at Cal Poly. The experiments expose students to the capabilities of industry-standard microprocessor-based relays through hands-on procedures that demonstrate common power system …

Energy Harvesting From Exercise Machines: Comparative Study Of Ehfem Performance With Dc-Dc Converters And Dissipative Overvoltage Protection Circuit, Cameron Kiddoo

Master's Theses

Energy Harvesting from Exercise Machines (EHFEM) is an ongoing project pursuing alternate forms of sustainable energy for Cal Poly State University. The EHFEM project seeks to acquire user-generated DC power from exercise machines and sell that energy back to the local grid as AC power. The end goal of the EHFEM project aims to integrate a final design with existing elliptical fitness trainers for student and faculty use in Cal Poly’s Recreational Center. This report examines whether including the DC-DC converter in the EHFEM setup produces AC power to the electric grid more efficiently and consistently than an EHFEM system …

Energy Harvesting From Exercise Machines: Buck-Boost Converter Design, Andrew E. Forster

Master's Theses

This report details the design and implementation of a switching DC-DC converter for use in the Energy Harvesting From Exercise Machines (EHFEM) project. It uses a four-switch, buck-boost topology to regulate the wide, 5-60 V output of an elliptical machine to 36 V, suitable as input for a microinverter to reclaim the energy for the electrical grid. Successful implementation reduces heat emissions from electrical energy originally wasted as heat, and facilitates a financial and environmental benefit from reduced net energy consumption.

Energy Management System Modeling Of Dc Data Center With Hybrid Energy Sources Using Neural Network, Khalid Althomali

Master's Theses

As data centers continue to grow rapidly, engineers will face the greater challenge in finding ways to minimize the cost of powering data centers while improving their reliability. The continuing growth of renewable energy sources such as photovoltaics (PV) system presents an opportunity to reduce the long-term energy cost of data centers and to enhance reliability when used with utility AC power and energy storage. However, the inter-temporal and the intermittency nature of solar energy makes it necessary for the proper coordination and management of these energy sources.

This thesis proposes an energy management system in DC data center using …

A Method For Evaluating Aircraft Electric Power System Sizing And Failure Resiliency, Cory Kenneth Kross

Master's Theses

With the More Electric Aircraft paradigm, commercial commuter aircraft are increasing the size and complexity of electrical power systems by increasing the number of electrical loads. With this increase in complexity comes a need to analyze electrical power systems using new tools. The Hybrid Power System Optimizer (HyPSO) developed by Airbus SAS is a simulator designed to analyze new aircraft power systems. This thesis project will first provide a method to assess the reliability of complex aircraft electrical power systems before and after failure and reconfiguration events. Next, an add-on to HyPSO is developed to integrate the previously developed reliability …

Arc Fault Circuit Interrupter Development For Residential Dc Electricity, Cassidy Alan Aarstad

Master's Theses

The following technical report describes the development and testing of an arc fault circuit interrupter (AFCI) for DC circuits operating primarily at 48 volts. We have identified an effective method for determining when arcing is occurring. Our method is primarily based on comparing the frequency spectrum of current flowing through the circuit during an arcing event to a known characteristic spectrum. Once an arc has been identified, our interrupter is capable of responding adequately to eliminate the arc. Hardware tests show the AFCI developed in this thesis responded, in all test cases, within 2 seconds of an arc fault occurrence. …

Low-Frequency Series Loaded Resonant Inverter Characterization, Alfredo Medina

Master's Theses

Modern power systems require multiple conversions between DC and AC to deliver power from renewable energy sources. Recent growth in DC loads result in increased system costs and reduced efficiency, due to redundant conversions. Advances in DC microgrid systems demonstrate superior performance by reducing conversion stages. The literature reveals practical DC microgrid systems composed of wind and solar power to replace existing fossil fuel technologies for residential consumers. Although higher efficiencies are achieved, some household appliances require AC power; thus, the need for highly efficient DC to AC converters is imperative in establishing DC microgrid systems. Resonant inverter topologies exhibit …

Wide-Band Gap Devices For Dc Breaker Applications, Olukayode O. Sodipe

Master's Theses

With the increasing interest in wide-band gap devices, their potential benefits in power applications have been studied and explored with numerous studies conducted for both SiC and GaN devices. This thesis investigates the use of wide-band gap devices as the switching element in a semiconductor DC breaker. It involves the design of an efficient semiconductor DC breaker, its simulation in SPICE, construction of a hardware prototype and the comparative study of SiC and Si versions of the aforementioned breaker. The results obtained from the experiments conducted in the process of concluding this thesis show that the SiC version of the …

Modeling And Test Of The Efficiency Of Electronic Speed Controllers For Brushless Dc Motors, Clayton R. Green

Master's Theses

Small electric uninhabited aerial vehicles (UAV) represent a rapidly expanding market requiring optimization in both efficiency and weight; efficiency is critical during cruise or loiter where the vehicle operates at part power for up to 99% of the mission time. Of the four components (battery, motor, propeller, and electronic speed controller (ESC)) of the electric propulsion system used in small UAVs, the ESC has no accepted performance model and almost no published performance data. To collect performance data, instrumentation was developed to measure electrical power in and out of the ESC using the two wattmeter method and current sense resistors; …

Adaptive Automotive Lighting Systems, Marc W. Haeberlin

Master's Theses

Over the past few years, the use of LEDs within the automotive and avionic industries has increased due to their high efficiency, durability and wide range of light brightness. As the use of LEDs within these industries grows, a need for reliable, high performance drivers becomes more relevant. Companies are implementing LEDs for applications involving adaptive lighting or simple dimming features. This thesis shows implementation of various non-isolated analog converters integrated with digital dimmers to achieve these adaptive lighting systems. Adaptive lighting systems involve reading an input from an external source (brake pedal or steering wheel) and changing the brightness …

Universal Programmable Battery Charger With Optional Battery Management System, Michael Duke Desando

Master's Theses

This report demonstrates improvements made in battery charging and battery management technology through the design of a universal programmable battery charger with optional battery management system attachment. This charger offers improvements in charge efficiency and unique battery charging algorithms to charge a variety of battery chemistries with variety of power requirements. Improvements in efficiency result from a synchronous Buck Controller topology as compared to previous universal chargers that use asynchronous Buck-Boost Converter topologies. This battery charger also surpasses current universal battery chargers by offering different charge modes for different battery chemistries. Charge modes provide the user an option between extending …

Three-Phase Generation Using Reactive Networks, Tattiana Karina Coleman Davenport

Master's Theses

Household appliances utilize single-phase motors to perform everyday jobs whether it is to run a fan in an air conditioner or the compressor in a refrigerator. With the movement of the world going “green” and trying to make everything more efficient, it is a logical step to start with the items that we use every day. This can be done by replacing single-phase motors with three-phase motors in household appliances. Three-phase motors are 14% more efficient than single-phase motors when running at full load and typically cost less over a large range of sizes [1]. One major downside of incorporating …

A Low-Cost Loop Measurement Tool For Dc-Dc Converters, Shouee B. Lin

Master's Theses

Loop measurements are very important in evaluating dynamic performance of DC-DC converters. In this thesis, a small loop measurement tool as a low-cost alternative to a network analyzer is proposed. The tool is particularly useful when a network analyzer is not always available for use, for example when engineers are working on-site with customers or when a network analyzer is not affordable due to their relatively high cost. The design, simulation, and hardware implementation of the inexpensive loop measurement tool will be presented in this thesis. Results from computer simulation and hardware prototype demonstrate the ability of the proposed tool …

Grid-Scale Energy Storage: A Proposed Control Algorithm For Sodium Sulfur Batteries, Daniel Spaizman

Master's Theses

With carbon dioxide levels in our atmosphere reaching record highs and 2020 quickly approaching, California is expected to pave the way for the United States in terms of replacing fossil fuel generation facilities with various renewable energy power plants. It is well documented that the inherent variability and limited duty cycle of renewables has hindered their growth. Energy storage technologies represent the bridge that can help us cross the divide from where we stand to where we must stand in the next 6 years. Utility companies value services such as peak shaving, voltage support, and frequency regulation, all of which …

Improvements To A Bi-Directional Flyback Dc-Dc Converter For Battery System Of The Dc House Project, Michael Wu

Master's Theses

The DC House project relies primarily on renewable energy sources to provide DC power to the various loads of the house. However, not all renewable sources are capable of providing power at all times of the day. A back-up energy source in the form of a battery storage system must be available to meet the electrical needs of the house. A bi-directional flyback power converter was initially designed to allow a battery to charge from as well as discharge to the 48V bus line of the DC House. The design provided a 35W prototype to demonstrate the converter’s feasibility. Further …

Smart Wall Outlet Design And Implementation For The Dc House Project, Kevin Roy Mendoza

Master's Theses

Most everyday AC appliances are designed to operate off of 120V coming from the wall outlet in our homes. This voltage is a standard set from our established infrastructure. Unlike AC devices, DC devices do not have any set standard of voltage they all will run off of. This presents a problem for the DC house as the various loads that will be used will have different required input voltages. One set voltage for a wall outlet will not suffice for the DC House. This Smart Wall Outlet is designed with a DC-DC converter that will have its output voltage …

Dual High-Voltage Power Supply For Use On Board A Cubesat, Nicholas Weiser

Master's Theses

Since their conception in 1999, CubeSats have come and gone a long way. The first few that went into space were more of a “proof of concept,” and were more focused on sending simple data and photographs back to Earth. Since then, vast improvements have been made by over 40 universities and private firms, and now CubeSats are beginning to look towards interplanetary travel. These small satellites could provide a cost effective means of exploring the galaxy, using off the shelf components and piggy-backing on other launch vehicles with more expensive payloads. However, CubeSats are traditionally launched into Low Earth …

Modeling And Simulation Of Parallel D-Statcoms With Full-Wave Rectifiers, Jason Brinsfield

Master's Theses

In recent years, both a significant increase in electrical demand and a large influx of intermittent renewable energy sources have put a considerable stress on the nation’s electrical grid. Conventional power flow control techniques such as capacitor banks and tap-changing transformers are incapable of adequately handling the rapid fluctuations in power supply and demand that today’s grid experiences. Flexible AC Transmission System (FACTS) controllers are a practical way to compensate for such rapid power fluctuations. One type of shunt FACTS controller is the Static Synchronous Compensator (STATCOM), which uses fully controllable switches to source or sink reactive power to a …

System Design Considerations And The Feasibility Of Passively Compensated, Permanent Magnet, Iron-Core Compulsators To Power Small Railgun Platforms, Collin Taylor Macgregor

Master's Theses

This thesis provides insight into the different aspects of compulsator design for use with railgun systems. Specifically, the design space is explored for passively compensated, permanent magnet iron-core compulsators. Seven design parameters are varied within a compulsator model developed for the Cal Poly Compulsator (CPCPA). The Matlab code for this model is included within the appendix. Efforts were made to compare and validate this compulsator model to published data from existing systems. The compulsator model was found to match closely with discharge pulse length, but resulted in lower values for peak current and projectile velocity by 50% and 30% respectively …

Multiple Input Single Output (Miso) Tablet/ Phone Charger, Kevin Wong

Master's Theses

This thesis entails the design and implementation of a multiple input single output (MISO) DC-DC converter using the flyback topology to charge tablets/ smartphones or any USB powered portable device. The MISO converter will enable the use of various renewable energy sources such as a solar panel/ rechargeable battery combination, bicycle dynamo, hydroelectric power, and wind turbine. This paper will cover the design, simulations, and test results of the MISO converter. The flyback topology was chosen due to its low part count and its efficiency at low power. The proposed converter has a nominal 12V input to output USB 2.0 …

Design, Fabrication, And Testing Of An Emr Based Orbital Debris Impact Testing Platform, Jeffrey J. Maniglia Jr.

Master's Theses

This paper describes the changes made from Cal Poly’s initial railgun system, the Mk. 1 railgun, to the Mk. 1.1 system, as well as the design, fabrication, and testing of a newer and larger Mk. 2 railgun system. The Mk. 1.1 system is developed as a more efficient alteration of the original Mk. 1 system, but is found to be defective due to hardware deficiencies and failure, as well as unforeseen efficiency losses. A Mk. 2 system is developed and built around donated hardware from the Naval Postgraduate School. The Mk. 2 system strove to implement an efficient, augmented, electromagnetic …

Designing Anti-Islanding Detection Using The Synchrophasor Vector Processor, Ruth Christiana Huang

Master's Theses

ABSTRACT

Designing Anti-Islanding Detection Using the Synchrophasor Vector Processor

Ruth Huang

The need for distributed generation (DG) has become more and more popular because of the adverse effects of fossil fuels and the fear of running out of fossil fuels. By having DG, there are less transmission losses, voltage support, controllability of the system, decreased costs in transmission and distribution, power quality improvement, energy efficiency, and reduced reserve margin. The adverse effects of DG are voltage flicker, harmonics, and islanding. Islanding occurs when the DG continues to energize the power system when the main utility is disconnected. Detecting islanding is …

Design Of Portable Dc Light Bulb For The Dc House Project, Jan Marvin Perez Macairan

Master's Theses

This thesis focuses on the design and implementation of the Portable DC Light Bulb system for Cal Poly San Luis Obispo’s DC House Project. The DC Portable Light Bulb highlights the NiMH battery charging circuit, buck converter, and boost converter. The system is intended as a flashlight adaptor placed in between the dimmable DC light bulb and its screw base. The adaptor adds a portability feature to the DC light bulb to provide lighting wherever the user pleases. The Portable DC Light Bulb system is designed to operate with an input range of 24V-60V and regulate an output voltage of …

Impact Of Photovoltaic System Penetration On The Operation Of Voltage Regulator Equipment, Abesh Sorab Mubaraki

Master's Theses

The growing popularity of photovoltaic (PV) generation systems leads to an increase in the number of residential and commercial grid-tied PV systems that interconnect to the distribution circuit. This affects the characteristics of the distribution circuit; for example, the assumption that the voltage profile of a radial line decreases down-stream becomes invalid because of the addition of the PV system on the line. This poses new challenges when setting the parameters of voltage regulating devices. Add to that the fact that PV systems are intermittent, especially on cloudy days, which make the line even more difficult to regulate, and the …