Engineering Commons^™

Joint Map Registration And High Resolution Image Estimation Using A Sequence Of Undersampled Images, Russell C. Hardie, Kenneth J. Barnard, Ernest E. Armstrong

Electrical and Computer Engineering Faculty Publications

n many imaging systems, the detector array is not sufficiently dense to adequately sample the scene with the desired field of view. This is particularly true for many infrared focal plane arrays. Thus, the resulting images may be severely aliased. This paper examines a technique for estimating a high-resolution image, with reduced aliasing, from a sequence of undersampled frames. Several approaches to this problem have been investigated previously. However, in this paper a maximum a posteriori (MAP) framework for jointly estimating image registration parameters and the high-resolution image is presented. Several previous approaches have relied on knowing the registration parameters …

Spontaneous Emission In Microcavity Lasers, Dustin Philip Ziegler

Theses and Dissertations

An understanding of spontaneous emission processes within microcavities is crucial in addressing the need to make tomorrow's microlasers more efficient. One approach to improving the device efficiency is to reduce the threshold input energy at which lasing begins to occur. It has been suggested that the threshold in a microcavity laser can be decreased by increasing the fraction of spontaneous emission into the lasing mode, this can be accomplished by preferentially coupling the gain medium of the laser to the electromagnetic cavity mode of interest. It therefore becomes necessary to understand the mechanism by which this coupling takes place. This …

Microelectromechanical Optical Beam Steering Systems, David M. Burns

Theses and Dissertations

The development of microelectromechanical systems (MEMS) has matured to the point where the fabrication of micron sized devices is feasible. State of the art MEMS construction processes now support the fabrication of novel optical devices that could not previously be built. This dissertation reports on the development of innovative micro optical devices such as Variable Blaze Gratings (VBGs) using state of the art MEMS construction processes. The principle application of the micro optical devices described in this dissertation is steering optical beams; however other applications such as spectral analysis are identified. Specific optical beam steering systems developed and characterized in …

A Novel Laboratory Course On Advanced Chemical Engineering Experiments, Jochen A. Lauterbach, S. White, X. Lui, G. M. Bodner, W. N. Delgass

Faculty Publications

The chemical engineering curriculum in the United States has trained generations of technical experts who have successfully optimized chemical processes and products once they entered the chemical industry. The U.S. chemical industry, however, has entered a critical stage in which it must be able to create new and differentiated value through technical innovations that arc essential for long-term survival. This innovation process will require new skills that go far beyond the traditional expertise for the optimization of tasks possessed by young chemical engineers. The innovators must be able to identify new opportunities, explore the boundaries of technology, evaluate critical issues, …

Shock Waves In Nonequilibrium Gases And Plasmas, William M. Hilbun

Theses and Dissertations

An analysis and assessment of three mechanisms describing plasma/shock wave interactions was conducted under conditions typically encountered in a weakly ionized glow discharge. The mechanisms of ion-acoustic wave damping, post-shock energy addition and thermal inhomogeneities were examined by numerically solving the Euler equations with appropriate source terms adapted for each mechanism. Ion-acoustic wave damping was examined by modeling the partially ionized plasma as two fluids in one spatial dimension using the Riemann problem as a basis. Post-shock energy addition in the form of nonequilibrium vibrational energy relaxation was also examined in one spatial dimension using the Riemann problem as a …

Segregation Of Bismuth To Triple Junctions In Copper, K.-M. Yin, Alexander H. King, T.E. Hsieh, F.-R. Chen, J.J. Kai, L. Chang

Alexander H. King

Bismuth segregation in copper has been studied using energy-dispersive X-ray spectrometry (EDX) in a JEOL 2010F transmission electron microscope. In addition to the expected solute enrichment at grain boundaries, we have observed extremely high concentrations of bismuth at certain triple junctions, with significantly greater enrichment factors than in the adjacent grain boundaries. It is shown here that the triple junction segregation is a function of the parameters of the grain boundaries at the triple line, and existence of this type of segregation implies that the affected triple junctions embody excess free energy. At least one of the observed triple junctions …

Vibrational Spectra In Ordered And Disordered Ni3al, Jeffrey D. Althoff, Dane Morgan, Didier De Fontaine, Mark Asta, S. M. Foiles, Duane D. Johnson

Duane D. Johnson

We calculate the vibrational density of states (DOS) and corresponding thermodynamic properties of L12 ordered and disordered Ni3Al in the quasiharmonic approximation using the embedded-atom method. Vibrational and thermodynamic properties, including vibrational entropy differences between ordered and disordered states, are found to be in good agreement with experiment. The DOS of the configurationally disordered alloy resembles a broadened version of the DOS of the L12 phase, not a one-atom per cell fcc DOS, and is shifted downward in frequency because the disordered state has a larger volume than the ordered phase. Calculations of the projected DOS indicate that high-frequency modes …

39th Rocky Mountain Conference On Analytical Chemistry

Rocky Mountain Conference on Magnetic Resonance

Preliminary program and registration information for the 39th annual meeting of the Rocky Mountain Conference on Analytical Chemistry, co-sponsored by the Colorado Section of the American Chemical Society and the Rocky Mountain Section of the Society for Applied Spectroscopy. Held in Denver, Colorado, August 3-7, 1997.

Experimental Investigation Of Nonlinear Dynamics In Single Mode Semiconductor Laser Diodes With Phase Conjugate Feedback, Gordon T. Hengst

Theses and Dissertations

The semiconductor laser diode offers a unique system to investigate nonlinear dynamics when optical feedback is applied. Although there is extensive research of laser diodes with optical feedback from normal dielectric mirrors, very little has been done experimentally to analyze the effects of degenerate phase conjugate feedback from a BaTiO₃ crystal. This research experimentally investigated the dynamics of a single-mode laser diode with weak phase conjugate feedback using both the self-pumped and double phase conjugate geometries. The experimental results validated a mathematical model which numerically evaluates the Lang-Kobayahsi coupled differential equations. The model simulated the nonlinear behavior of a …

Optimization Considerations For Adaptive Optics Digital Imagery Systems, Robert T. Brigantic

Theses and Dissertations

This dissertation had three objectives. The first objective was to develop image quality metrics that characterize Adaptive Optics System (AOS) performance. The second objective was to delineate control settings that maximize AOS performance. The third objective was to identify and characterize trade-offs between fully and partially compensated adaptive. For the first objective, three candidate image quality metrics were considered: the Strehl ratio, a novel metric that modifies the Strehl ratio by integrating the modulus of the average system optical transfer function to a 'noise-effective-cutoff' frequency at which some specified image spectrum signal-to-noise-ratio level is attained, and the noise-effective-cutoff frequency. It …

Experimental And Theoretical Investigations Of Order-Disorder In Cu2almn, Duane D. Johnson, M. Asta, J. J. Hoyt, B. C. Chakoumakos, S. T. Misture, J. D. Althoff, R. Mccormack

Duane D. Johnson

A combination of X-ray and neutron powder diffraction has been used to measure the two long range order parameters vs. temperature below the disorder-B2 transition in the ternary alloy Cu2 AlMn. The results indicate that at temperatures just below the critical point the Al + Mn sublattice is enriched in Al. First-principles calculations based on only the atomic numbers of Cu, Mn and Al support the experimentally-observed preference of Al for the Al + Mn sublattice, and reveal the interplay between the constituent binary systems that gives rise to this behavior.

Physical And Managed Risk Of Nuclear Waste, Lennart Sjöberg, Britt-Marie Drottz-Sjöberg

RISK: Health, Safety & Environment (1990-2002)

The authors describe their work on the perceived risk of nuclear waste in Sweden. Three levels of waste were studied, and comparisons between the perceptions of the public, politicians and nuclear experts are made.

Book Review Of Alla Yaroshinskaya, Chernobyl: The Forbidden Truth, John M. Gleason

RISK: Health, Safety & Environment (1990-2002)

Review of the book: Alla Yaroshinskaya, Chernobyl: The Forbidden Truth (Michele Kahn & Julia Sallabank, trans. University of Nebraska Press 1995). Introduction, foreword, list of illustrations, photographs. ISBN 0-8032-4912-8. [136 pp. Cloth $25.00; Paper $10.00. 312 N. 14th Street, Lincoln NE 68588-0484.]

Stiffness Of Measurement System And Significant Figures Of Displacement Which Are Required To Interpret Adhesional Force Curves, Nancy Burnham, Kunio Takahashi, Hubert Pollock, Tadao Onzawa

Nancy A. Burnham

Force curves obtained from an elastic contact theory are shown and compared with experimental results. In the elastic contact theory, a pin-on-disk contact is assumed and the following interaction are taken into consideration; (i) elastic deformation, (ii) the specific energy of adhesion in the area of the contact, which is expressed as the difference between the surface energies and the interface energy, (iii) the long-range interaction outside the area of contact, assuming the additivity of the Lennard-Jones type potential, and (iv) another elastic term for the measurement system such as the cantilever stiffness of an atomic force microscope (AFM). In …

The Decision To Reactivate A First-Generation Soviet Nuclear Power Plant: Conceptual And Decision-Analytic Frameworks, John M. Gleason

RISK: Health, Safety & Environment (1990-2002)

Explores a variety of factors that led to reopening the Armenian Metsamor facility notwithstanding general agreement that this is unwarranted technologically.

Local Nonequilibrium Transport Models, Sergey Sobolev

Sergey Sobolev

No abstract provided.

Local Non-Equilibrium Diffusion Effects On The Kinetic Phase Boundaries In Solidification, Sergey Sobolev

Sergey Sobolev

No abstract provided.

Reflection High-Energy Electron-Diffraction Study Of Melting And Solidification Of Pb On Graphite, Z. H. Zhang, P. Kulatunga, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

The melting and solidification of Pb thin films on pyrolytic graphite are investigated in situ by reflection high-energy electron diffraction. Thin films with thicknesses of 4-150 monolayers are investigated. The surface morphology of the thin films were studied by scanning electron microscopy. Superheating of the Pb thin films by 4±2 to 12±2 K is observed from diffraction intensity measurements. Upon cooling the substrate, the Pb on graphite is seen to supercool by ∼69±4 K.

Femtosecond Photoemission Study Of Ultrafast Electron Dynamics On Cu(100), J. Cao, Y. Gao, R. J. D. Miller, Hani E. Elsayed-Ali, D. A. Mantell

Electrical & Computer Engineering Faculty Publications

The energy dependence of the relaxation of photoexcited electrons in copper was measured using femtosecond time-resolved photoemission spectroscopy to within 0.3 eV above the Fermi level. By performing lifetime measurements under different surface conditions, several surface dynamical processes were investigated. In particular, an anomalous long lifetime feature, which cannot be explained with Fermi-liquid theory, was observed in the lifetime-energy curve. This feature was found originating from the photoexcitation of the strongly localized Cu 3d electrons. ©1997 American Physical Society

Turbulence Modeling Of The Toroidal Wall Heat Load Due To Shear Flows Over Cavities In The Neutral Gas Blanket Divertor Regime, George Vahala, Linda L. Vahala, Joseph Morrison

Electrical & Computer Engineering Faculty Publications

Heat loads to the target plate in reactor tokamaks are estimated to be orders of magnitude higher than those that can be withstood by known materials. In regimes of plasma detachment, there is strong evidence that plasma recombination occurs near the divertor plate, leading to a cold neutral gas blanket. Because of the strong coupling between the plasma and the neutrals within the divertor region, there is significant neutral flows along field lines up to Mach 1.2 and Reynolds numbers over 1000. The effects of three dimensional (3D) neutral turbulence within the gas blanket on heat deposition to the toroidal …

Maximum Individual & Vicinity-Average Dose For A Geologic Repository Containing Radioactive Waste, Thomas H. Pigford

RISK: Health, Safety & Environment (1990-2002)

Explains the basis for his strong dissent to an NAS report on Yucca Mountain.

Academy Recommendations On The Proposed Yucca Mountain Waste Repository: Overview And Criticisms, Kristin S. Shrader-Frechette

RISK: Health, Safety & Environment (1990-2002)

Offers alternative criticism of the NAS report.

On-Line System Identification For Control System Applications In Particle Accelerators, Mahesh Chowdhary

Dissertations, Theses, and Masters Projects

Particle accelerators require a number of feedback systems in order to stabilize a variety of parameters. The Continuous Electron Beam Accelerator at Thomas Jefferson National Accelerator Facility presents a unique set of control and identification problems. This accelerator produces a continuous electron beam with energies between 0.5 and 4.0 GeV to be delivered to the experimental halls. In order to meet stringent beam quality requirements specified by the experimental halls, the position and the energy of the electron beam needs to stabilized at various locations in the accelerator.;A number of noise measurement tests were conducted at various locations in the …

Microwave Plasma Chemical Vapor Deposited Diamond Tips For Scanning Tunneling Microscopy, Sacharia Albin, Jianli Zheng, John B. Cooper, Weihai Fu, Arnel C. Lavarias

Electrical & Computer Engineering Faculty Publications

Diamond microparticles were grown on etched tungsten wires using a microwave plasma-assisted chemical vapor deposition process. The apexes on cubo-octahedral particles bound by {100} and {111} facets were effectively used as tunneling tips for scanning tunneling microscopy. The atomically resolved surface image of highly oriented pyrolytic graphite was acquired. Tunneling characteristics revealed a higher electron emission from the diamond tips than that from the platinum–iridium tips. The same diamond tips were used to produce surface indentation and its image. © 1997 American Institute of Physics.

Propagation Of Rayleigh Waves In Thin Films, Agus A. Ananda

Dissertations, Theses, and Masters Projects

With the advent of thin film technology and more recently its applications in microelectronics and control of surface properties, the interest in mechanical properties of thin films has grown tremendously. Mechanical defects such as creep, fracture and adhesion loss, play a very important role in physical instabilities of thin film materials. An acoustic microscope has been built to study mechanical properties of thin-films. The microscope operates at a nominal frequency of 50 MHz. Rayleigh surface waves velocities on the surface of film-substrate systems were measured from V(z) curves generated by the acoustic microscope. V(z) curves are produced from interference between …

Investigation Of The Optical Properties Of Ordered Semiconductor Materials, Jack E. Mccrae Jr.

Theses and Dissertations

Optical studies have been conducted upon CdGeAs₂ and ZnGeP₂, two of the most promising semiconductors being developed for mid-infrared non-linear optics applications. These experiments included photoluminescence (PL) studies of both compounds as well as photoreflectance (PR) measurements upon CdGeAs₂. In addition, Hall effect measurements were carried out upon CdGeAs₂, to aid in interpretation of the optical data. PL was measured as a function of laser power, sample temperature, and crystal orientation for CdGeAs₂. One broad weak peak near 0.38 eV, and another somewhat narrower and often far brighter peak near 0.57 …

A System For Collecting Milligram Quantities Of Cloud Condensation Nuclei, Darryl J. Alofs, Donald E. Hagen, Steven D. Medley, Daniel R. White, John L. Schmitt, Allen L. Williams

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An Experimental System to Collect Cloud Condensation Nuclei (CCN) Onto Filters in Amounts Sufficient for Chemical Analysis is Described. This Experimental Apparatus is Designed to Process Ambient Air at a Rate of More Than 1 M3/min. Two Identical Systems Have Been Built. One is Installed in a Laboratory at Rolla, MO. the Other is Installed on an 11 M Long Trailer. the System Isolates Three Size Classes of CCN, Having Mass Median Diameters of 0.27, 0.12, and 0.075 Μm, Respectively, and Mass Collection Rates of 11.5, 1.28, and 0.13 Mg/day, Respectively. the above Sizes and Collection Rates Are Obtained from …

Characterization Of Iron Oxides And Atmospheric Corrosion Of Steel, Sei Jin Oh

Physics Theses & Dissertations

The study of corrosion behavior was performed using three different analytical techniques, which provided information on the formation, development and layering of iron oxides on the corrosion products as a function of atmospheric conditions, exposure time and type of steel. In particular, the protective layer formed on weathering steel was investigated as a function of different amounts of alloying elements in the steel, atmospheric conditions and exposure times. Combined together, the results provided a better understanding of the atmospheric corrosion behavior of steel, and formed a part of database of the atmospheric corrosion characteristics.

Accurate characterization of the iron oxides …