Engineering Commons^™

Experimental Analysis On Recycling And Mechanical Properties Of Waste Cement, Chen Liang

Journal of China & Foreign Highway

In order to recycle waste cement, construction waste cement materials were collected in the laboratory, and they were crushed, ground, and heat treated to facilitate reuse. Then, the waste cement was combined with the commonly used active fly ash admixture to prepare a new cement material for test analysis. The results show that the new cement material produced by industrial by-product, fly ash and waste cement material is feasible. A small amount of construction waste cement material (about 5%) can increase the 28-day compressive strength of cement by more than 50%, and the compressive strength of the prepared building material …

Experimental Study On Characteristics And Stability Of Different Aged Steel Slag Aggregate, Zhang Hongri, Wang Guiyao, Feng Jian, Lan Tianzhu, Wu Tao

Journal of China & Foreign Highway

Steel slag aggregate has good building material properties, but the utilization rate of steel slag in road engineering is low at present. In this paper, the chemical composition, basic physical and mechanical indexes, f⁃CaO, f⁃MgO, pulverization rate, CRB expansion rate, and other indexes of open-air aged steel slag aggregate in Fangchenggang, Guangxi Province for 0, 6, and 12 months were studied. The results show that the physical and mechanical properties of steel slag aggregate basically meet the requirements of road base materials and subgrade fillers, but the indexes of f⁃CaO, pulverization rate, and CRB expansion rate of steel slag aggregate …

Influence Factors Of Deicing And Thaw Performance Of Asphalt Mixture With Low Freezing Point, Zhou Shuiwen, Lin Fang, Zhang Xiaohua, Zhang Lingbo, Jiang Haoqiu

Journal of China & Foreign Highway

The conductivity test was used to study the release law of thawing and deicing components. The freezing test was used to study the cooling law of the mixture, and the thawing rate test was used to study the thawing and deicing performance. The results show that the release of thawing and deicing components of materials with a low freezing point is temperature-dependent, and the release at the high temperature is 3.49–3.77 times that at the low temperature. The granular materials tend to dissolve in water, which results in the release rate of thawing and deicing components faster than that of …

Evaluation Of Anti‐Cracking Performance Of Recycled Concrete With Recycled Rubber/Sbs Composite Modified Asphalt, Li Xiaobin

Journal of China & Foreign Highway

In order to improve the crack resistance of recycled asphalt mixture, a new styrenic block copolymer (SBS)/rubber composite modified asphalt with excellent crack resistance was proposed for the regeneration of reclaimed asphalt pavement (RAP). Based on the creep of low temperature bending beam, confined temperature stress, and four-point bending fatigue test, the low temperature cracking resistance and fatigue cracking performance of composite modified asphalt and SBS-modified asphalt were studied. The results show that the addition of rubber can improve the low temperature and medium temperature crack resistance of recycled asphalt concrete, which may be related to the propagation of micro-cracks …

Study On Anti‐Scattering Performance Of Asphalt Concrete On Aggregate Scattering Pavement Of Highway, Yang Siyuan, Chen Guiliang

Journal of China & Foreign Highway

Due to the lack of quantitative evaluation methods for aggregate scattering degree of expressway asphalt pavement in China and abroad, according to the disease characteristics of surface layer spalling, this paper adopted the Cantabro standard dispersion test to sample the concrete of the section with aggregate scattering of Huangqunan Expressway (G3) in Zhejiang Province. The dispersion impact damage modes of the mixture with different severity were analyzed, and the anti-dispersion performance of concrete was evaluated by mass loss rate and water absorption rate. The results show that aggregate scattering will reduce the density of the concrete structure at the surface …

Variable Speed Limit Control Method For Highway Under Dense Fog, Sun Jiancheng, Qiao Jiaxing

Journal of China & Foreign Highway

In order to solve the problem of traffic safety on expressways under dense fog and change the original fixed speed limit measures, a variable speed limit control method based on the safe allowable speed was proposed. The speed limit value was calculated based on the regulations in road traffic safety law on the speed under dense fog by considering that the traffic law does not mention the road alignment conditions, road conditions, and other factors, and the monitor data was used to approximate replace the data of individual vehicles for data optimization, and the safe speed and safe distance of …

Design And Experimental Study On Special Spherical Support Of Pingtang Bridge, Tang Zhi, Ma Baihu, Du Bin, Xu Xiangdong, Xia Junyong

Journal of China & Foreign Highway

The vertical bearing capacity of the 16# pier of Pingtang Bridge is 10 000 kN, and the horizontal bearing capacity along the bridge is 12 000 kN, which is 120% of the vertical bearing capacity. The support angle needs to reach the technical parameter requirements of 0.05 rad, which far exceeds the requirements of 10–40% horizontal force of conventional highway supports. According to the specific engineering situation, a new type of support with a large horizontal bearing capacity was designed. Firstly, the finite element model of the support was established to analyze the mechanical properties of the support, and the …

Study On Practical Method Of Safety Assessment For Bridges Under Heavy‐Cargo Transportation, Jiang Xu, Wang Wanfeng, He Zhensheng, Gao Xuefeng

Journal of China & Foreign Highway

In order to meet the requirements of the industry for the high efficiency, safety, and reliability of the traffic safety assessment of heavy-duty vehicles, this paper proposed a method that combined a real-time monitoring system with a finite element method for the traffic safety assessment of heavy-duty vehicles on bridges and verified the method through practical projects. The paper evaluated the bridge’s technical condition level before the heavy-duty vehicle passes and determined the resistance reduction factor considering the bridge’s technical condition level. The finite element analysis model of the bridge was established, and the reliability of the model was verified …

Research On Vibration Reduction Measures Of Short‐Hole Blasting For Pile Group Foundation Of Bridge, Long Lidun, Ji Zhongyan, Li Shaofang, Zhou Xu

Journal of China & Foreign Highway

In the construction of pile hole blasting of group pile foundation of bridges, due to the small clear distance between piles, the blasting vibration will have adverse effects on the wall protection of adjacent pile holes and the poured pile core concrete. Measures thus should be taken to control the seismic wave vibration velocity. In view of the inapplicability of conventional blasting vibration reduction measures such as reducing charge and setting isolation ditch in the construction of pile group foundation of the bridge, this paper proposed vibration reduction measures such as setting isolation holes and using air bags to replace …

Analysis Of Influence Parameters Of Steel Corrugated Plate‐Concrete Composite Arch Culvert, Zhang Haijun

Journal of China & Foreign Highway

In order to explore the parameter effect of a composite arch culvert with corrugated steel plate and concrete, based on the engineering background of a composite arch culvert, the influence rules of four parameters, namely fill height, pipe diameter, wall thickness, and uneven settlement, on the stress and deformation of the arch culvert were analyzed based on the control variable method. The results show that the deformation and stress of the arch culvert are positively correlated with the fill height h and pipe diameter R. When h < 25 m, the deformation and stress increase linearly with the increase in the fill height, and when h > 25 m, the deformation and stress increase in a curve form. When R …

Research And Analysis On Controlled Blasting Demolition Of Continuous Thin‐Walled Box Ribbed Arch Bridge, Ma Shaojun, Chen Huibin, Chai Wendong, Zhang Chunquan, Wang Yuan

Journal of China & Foreign Highway

The 1st bridge of the Jialing River in Pengan County is erected over the Jialing River, a tributary of the Yangtze River. Due to earthquakes and perennial high load operation, the overall technical condition is “Class Ⅴ”, which cannot meet the requirements of the design load grade. This bridge is the longest highway bridge dismantled in Sichuan Province. Its structure is a multi-span continuous thin-walled box ribbed arch bridge. In addition, there are obvious diseases, so the demolition is difficult, and the safety risk is great. For the demolition of the bridge by controlled blasting, numerical simulation, shaped charge cutting …

Study On Parameter Optimization Of Feet‐Lock Anchor Pipes Of Tunnels In Unconsolidated Formation, Tang Heqing, Jiang Xishan, Yang Peng

Journal of China & Foreign Highway

In order to give full play to the supporting role of the feet-lock anchor pipe in the tunnel with unconsolidated formation, it is necessary to obtain the optimal construction parameters of the feet-lock anchor pipe. Based on a tunnel project on the Huaping–Lijiang Expressway in Yunnan Province, this paper conducted numerical simulation and field test analysis. By comparing the arch subsidence and horizontal convergence of the supporting structure when the feet-lock anchor pipe with different parameters was constructed, the paper explored the characteristics and causes of the influence of construction parameters on the feet-lock effect. The results show that the …

Simulation Study On Flame Retardant Effect Of Warm‐Mixed Flame Retardant Pavement In Highway Tunnel

Journal of China & Foreign Highway

In order to obtain the flame retardant effect of the warm-mixed flame retardant asphalt pavement in highway tunnels, based on the finite element method and thermodynamics theory, the thermal analysis module of Ansys finite element software was used to study the flame retardant effect of ordinary asphalt pavement, flame retardant asphalt pavement, and warm-mixed flame retardant asphalt pavement under different fire scales. The maximum temperature of the three types of pavement increased with the increase in the fire scale. Under any fire scale, the flame retardant effect of the warm-mixed flame retardant asphalt pavement was increased by 4.9%–8.5% compared with …

Installation Construction Technology Of Composite Girder Cable‐Stayed Bridge Superstructure In Deep‐Cutting Gorge, Ren Lei, Lu Liang, Dong Zhengliang

Journal of China & Foreign Highway

In view of the installation problems of superimposed beam cable-stayed bridge across the deep canyon, this paper studied the superimposed beam lifting, transport on beam, and superimposed beam installation and proposed three kinds of lifting technology with tower truss crane, beam lifting door crane, and large tower crane, as well as two kinds of installation technology including piecemeal assembly by full rotating deck crane and whole segment assembly truss deck crane. It also made a relative comparative analysis, solving the difficulty in vertical lifting on such bridges and providing a reference for the construction of the same type of cable-stayed …

Experiment Research Of High Pressure Jet Grouting Pile On Ultra‐Shallow Buried Tunnel In Strong Weathered Stratum, Lu Liyang, Liu Huan, Li Pinpin

Journal of China & Foreign Highway

By taking the ultra-shallow buried construction of Xinwu Tunnel in Luoding–Xinyi Expressway in Guangdong Province as the engineering background, the key construction parameters and formation reinforcement effect of high-pressure rotary churning pile in ultra-shallow buried tunnel surrounding rock of fully weathered strata were compared. The results show that: ① slurry pressure, rotary churning speed, and lifting speed have obvious effects on the static load bearing capacity of a single pile. Under the same static load condition, greater slurry pressure indicates a lower cumulative settlement value of a single pile and a smaller increase in cumulative settlement value, and the change …

Study On Anti‐Scattering Performance Of Asphalt Concrete On Aggregate Scattering Pavement Of Highway, Yang Siyuan, Chen Guiliang

Journal of China & Foreign Highway

Due to the lack of quantitative evaluation methods for aggregate scattering degree of expressway asphalt pavement in China and abroad, according to the disease characteristics of surface layer spalling, this paper adopted the Cantabro standard dispersion test to sample the concrete of the section with aggregate scattering of Huangqunan Expressway (G3) in Zhejiang Province. The dispersion impact damage modes of the mixture with different severity were analyzed, and the anti-dispersion performance of concrete was evaluated by mass loss rate and water absorption rate. The results show that aggregate scattering will reduce the density of the concrete structure at the surface …

Variable Speed Limit Control Method For Highway Under Dense Fog, Sun Jiancheng, Qiao Jiaxing

Journal of China & Foreign Highway

In order to solve the problem of traffic safety on expressways under dense fog and change the original fixed speed limit measures, a variable speed limit control method based on the safe allowable speed was proposed. The speed limit value was calculated based on the regulations in road traffic safety law on the speed under dense fog by considering that the traffic law does not mention the road alignment conditions, road conditions, and other factors, and the monitor data was used to approximate replace the data of individual vehicles for data optimization, and the safe speed and safe distance of …

Application Of Digital Image Processing In Cracks Of Concrete Pavement, Gao Fan, He Chunguang, Wang Pengzhang, Qin Yanping, Duo Huaqiong

Journal of China & Foreign Highway

The image obtained by using the traditional crack detection method of concrete pavement has some problems, such as low contrast and high noise, which makes it difficult to meet the requirements of modern road engineering management or non-destructive testing. In order to eliminate the interference in crack images, digital image processing technology was used to improve the image quality through computers. This paper took digital image processing as the core and introduced its development and application in pavement cracks. Based on the research progress and achievements of digital image processing on pavement cracks in recent years, the principles and characteristics …

Design And Experimental Study On Special Spherical Support Of Pingtang Bridge, Tang Zhi, Ma Baihu, Du Bin, Xu Xiangdong, Xia Junyong

Journal of China & Foreign Highway

The vertical bearing capacity of the 16# pier of Pingtang Bridge is 10 000 kN, and the horizontal bearing capacity along the bridge is 12 000 kN, which is 120% of the vertical bearing capacity. The support angle needs to reach the technical parameter requirements of 0.05 rad, which far exceeds the requirements of 10–40% horizontal force of conventional highway supports. According to the specific engineering situation, a new type of support with a large horizontal bearing capacity was designed. Firstly, the finite element model of the support was established to analyze the mechanical properties of the support, and the …

Study On Practical Method Of Safety Assessment For Bridges Under Heavy‐Cargo Transportation, Jiang Xu, Wang Wanfeng, He Zhensheng, Gao Xuefeng

Journal of China & Foreign Highway

In order to meet the requirements of the industry for the high efficiency, safety, and reliability of the traffic safety assessment of heavy-duty vehicles, this paper proposed a method that combined a real-time monitoring system with a finite element method for the traffic safety assessment of heavy-duty vehicles on bridges and verified the method through practical projects. The paper evaluated the bridge’s technical condition level before the heavy-duty vehicle passes and determined the resistance reduction factor considering the bridge’s technical condition level. The finite element analysis model of the bridge was established, and the reliability of the model was verified …

Study On Pavement Performance Of Waterborne Epoxy Emulsified Asphalt And Its Application In Micro‐Surface, Jiang Hai, Liu Dachang

Journal of China & Foreign Highway

In order to improve the pavement performance at micro-surface, waterborne epoxy resin was used to modify the emulsified asphalt, and the compatibility, microstructure, mechanical properties, rheological properties, and pavement performance of mixtures of the modified emulsified asphalt were studied. The storage stability test shows that the epoxy emulsion has good compatibility with emulsified asphalt. With the increase in waterborne epoxy resin content, the modified emulsified asphalt tends to form an epoxy resin-dominated skeleton structure. At the same time, with the increase in waterborne epoxy resin content, the adhesion and mechanical properties of emulsified asphalt and aggregate are significantly improved. At …

An Intelligent Decision Support Model For Optimal Selection Of Machine Tool Under Uncertainty: Recent Trends, Ibrahim M. Hezam

Neutrosophic Systems with Applications

Many scholars have been interested in the subject of machine tool selection as a result of the growing number of different machines and the continuous advancement of technology associated with these machines. The selection of an unsuitable machine tool may lead to a variety of issues, including limitations on production capacities and productivity indicators when taking into account both time and money from an industrial and practical perspective. The present strategy of selecting machine tools, known as multi-criteria decision-making (MCDM), relies on the subjective viewpoint the vast majority of the time. When selecting an appropriate machining tool, however, it is …

Design, Collaborate, Thrive: The Broad Ripple Avenue Project, Jessica Hawley, Emily Nelson, Ericka Miller

Purdue Road School

Broad Ripple Avenue (College Avenue to Winthrop Avenue) needed large-scale stormwater improvements. With the help of the Lochmueller Group and the Broad Ripple Village Association, Indianapolis DPW perceptively took this opportunity to also improve pedestrian facilities and regional multi-modal connectivity by combining multiple regional projects into one construction contract. This consolidation allowed for a cohesive public message through proactive public involvement. Presenters will share how consensus was built between invested parties through a successful public and private partnership.

Remote Medical Diagnosis Via Infrared Thermography And Augmented Reality, Frederick M. Selkey

USF Tampa Graduate Theses and Dissertations

Fast, accurate, and non-invasive diagnostic techniques are required by the medical industry to increase the success of medical treatments and enhance the quality of patient care. Medical IRT has been demonstrated reasonably effective at diagnosing and monitoring several physiological conditions. Diversities in the human body, physical and psychological condition, measurement equipment, and environment all influence the sensitive readings obtained by passive IR measurement devices. New standards for medical IRT and fever screening have been demonstrated effective, but there is limited adherence to the guidelines [36]. Absolute temperature readings require regular calibration checks and can easily be thrown off by noise. …

The Rise And Risks Of Internet Of Things, Diamond E. Hicks

Cybersecurity Undergraduate Research Showcase

Internet of Things (IoT) has become a necessary part of our everyday lives. IoT is the network in which many different devices communicate, connect, and share data. Though how IoT got to where it is today, the issues it faced, and how it affects our lives today is not common knowledge. Despite the fact that IoT has advanced our technology to what it is today, people do not completely understand what it does.

Chatgpt As Metamorphosis Designer For The Future Of Artificial Intelligence (Ai): A Conceptual Investigation, Amarjit Kumar Singh (Library Assistant), Dr. Pankaj Mathur (Deputy Librarian)

Library Philosophy and Practice (e-journal)

Abstract

Purpose: The purpose of this research paper is to explore ChatGPT’s potential as an innovative designer tool for the future development of artificial intelligence. Specifically, this conceptual investigation aims to analyze ChatGPT’s capabilities as a tool for designing and developing near about human intelligent systems for futuristic used and developed in the field of Artificial Intelligence (AI). Also with the helps of this paper, researchers are analyzed the strengths and weaknesses of ChatGPT as a tool, and identify possible areas for improvement in its development and implementation. This investigation focused on the various features and functions of ChatGPT that …

A Solution Technique Of Transportation Problem In Neutrosophic Environment, Manas Karak, Animesh Mahata, Mahendra Rong, Supriya Mukherjee, Sankar Prasad Mondal, Said Broumi, Banamali Roy

Neutrosophic Systems with Applications

In this article, we presented a ranking system based on the sign distance in a new direction, such that to compare different single-valued neutrosophic numbers (SVN-numbers), a decision maker has the chance of flexibility. We also developed some important definitions, like level-(α,β,γ) neutrosophic point, and some properties related to the sign distance ranking function. Finally, the sign distance ranking function is applied to solving the neutrosophic transportation problem (NTP) with SVN-number converted into a transportation problem (TP) with crisp data, and to illustrate the appropriateness of this function, we gave two numerical illustrations.

Deep Reinforcement Learning Based Optimization Techniques For Energy And Socioeconomic Systems, Salman Sadiq Shuvo

USF Tampa Graduate Theses and Dissertations

Optimization, which refers to making the best or most out of a system, is critical for an organization's strategic planning. Optimization theories and techniques aim to find the optimal solution that maximizes/minimizes the values of an objective function within a set of constraints. Deep Reinforcement Learning (DRL) is a popular Machine Learning technique for optimization and resource allocation tasks. Unlike the supervised ML that trains on labeled data, DRL techniques require a simulated environment to capture the stochasticity of real-world complex systems. This uncertainty in future transitions makes the planning authorities doubt real-world implementation success. Furthermore, the DRL methods have …

A Solution Technique Of Transportation Problem In Neutrosophic Environment, Manas Karak, Animesh Mahata, Mahendra Rong, Supriya Mukherjee, Sankar Prasad Mondal, Said Broumi, Banamali Roy

Neutrosophic Systems with Applications

In this article, we presented a ranking system based on the sign distance in a new direction, such that to compare different single-valued neutrosophic numbers (SVN-numbers), a decision maker has the chance of flexibility. We also developed some important definitions, like level-(α,β,γ) neutrosophic point, and some properties related to the sign distance ranking function. Finally, the sign distance ranking function is applied to solving the neutrosophic transportation problem (NTP) with SVN-number converted into a transportation problem (TP) with crisp data, and to illustrate the appropriateness of this function, we gave two numerical illustrations.

The Use Of Neutrosophic Methods Of Operation Research In The Management Of Corporate Work, Maissam Jdid, Florentin Smarandache

Neutrosophic Systems with Applications

The science of operations research is one of the modern sciences that have made a great revolution in all areas of life through the methods provided by it, suitable and appropriate to solve most of the problems that were facing researchers, scholars and those interested in the development of societies, and the most beneficiaries of this science were companies and institutions that are looking for scientific methods that help them manage their work so that they achieve the greatest profit and the lowest cost, and one of the important methods that have been used in the management of companies we …