Engineering Commons^™

Nebraska Summary: S944 Case-Ih Farmall 115c, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S943 Case-Ih Farmall 105c, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S942 Case-Ih Farmall 95c, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2098:John Deere 8245r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2095: Case Ih Steiger 500, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2094: Case Ih Steiger 470, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2092a: New Holland T9.435, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2090: John Deere 7230r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2085: John Deere 7250r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2084: John Deere 7270r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2083: John Deere 7290r, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2087: Challenger Mt755e, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Pedestrian Head Protection During Car To Pedestrian Accidents: In The Event Of Primary Impact With Vehicle And Secondary Impact With Ground, Vishal Gupta

Wayne State University Dissertations

Current regulations for assessing pedestrian safety use a simplified test setup that ignores many real-world factors. In particular, the level of protection is assessed using a free-motion headform impacting the vehicle's hood at a fixed angle. As such, this test setup does not capture the effect due to the vehicle front-end profile, nor does it comprehend injury due to a possible secondary impact of the pedestrian's head with ground. This thesis aims to numerically simulate vehicle to pedestrian crashes to develop knowledge that may suggest ways to improve safety above and beyond the regulatory tests. Inputs to the simulations include …

Combustion Visualization And Particulate Matter Emission Of A Gdi Engine By Using Gasoline And E85, Po-I Lee

Wayne State University Dissertations

In order to increase engine efficiency as well as to reduce emission, optimizing combustion is always the challenge in research and product development. Gasoline direct injection (GDI) engines have been popularized due to its higher power density, fuel efficiency, and the possibility for advanced engine technologies over conventional port-fuel-injection (PFI) gasoline engines. However, many issues are heavily investigated, such as air-fuel mixing preparation, fuel wall-wetting, higher HC and PM emissions, catalytic convertor efficiency, knocking, and pre-ignition. Besides, advanced technologies represent higher production cost.

Because of the limited resource of petroleum-based fuels, ethanol is deemed as the alternative fuel for gasoline …

Polymer Aggregation Correlated Transition From Schottky-Junction To Bulk Heterojunction Organic Solar Cells, Bin Yang, Zhengguo Xiao, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

The fullerene-based organic Schottky-junction solar cells have recently attracted intensive research interest because of their unique electrical performance, such as significant photocurrent generation from excitons created in fullerenes and large open-circuit voltage (V_OC) output induced by high Schottky-barrier height between the anode and the fullerene acceptor. This manuscript reports another remarkably appealing advantage that the fullerene-based Schottky-junction solar cells are more stable than the bulk heterojunction counterparts. The better stability is likely due to mitigative polymer photo-oxidation and/or little morphological change of active film in the aged Schottky-junction devices. The transition from Schottky-junction to bulk heterojunction appears at …

Phase Transitions In Mechanically Milled Mn-Al-C Permanent Magnets, Michael J. Lucis, Timothy E. Prost, Xiujuan Jiang, Meiyu Wang, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Faculty Publications

Mn-Al powders were prepared by rapid solidification followed by high-energy mechanical milling. The rapid solidification resulted in single-phase ε. The milling was performed in both the ε phase and the τ phase, with the τ-phase formation accomplished through a heat treatment at 500 °C for 10 min. For the ε-milled samples, the conversion of the ε to the τ phase was accomplished after milling via the same heat treatment. Mechanical milling induced a significant increase in coercivity in both cases, reaching 4.5 kOe and 4.1 kOe, respectively, followed by a decrease upon further milling. The increase in coercivity was the …

Biomechanical Strain As A Trigger For Pore Formation In Schlemm’S Canal Endothelial Cells, Sietse T. Braakman, Ryan M. Pedrigi, A. Thomas Read, James A. E. Smith, W. Daniel Stamer, C. Ross Ethier, Darryl R. Overby

Department of Mechanical and Materials Engineering: Faculty Publications

The bulk of aqueous humor passing through the conventional outflow pathway must cross the inner wall endothelium of Schlemm’s canal (SC), likely through micron-sized transendothelial pores. SC pore density is reduced in glaucoma, possibly contributing to obstructed aqueous humor outflow and elevated intraocular pressure (IOP). Little is known about the mechanisms of pore formation; however, pores are often observed near dome-like cellular outpouchings known as giant vacuoles (GVs) where significant biomechanical strain acts on SC cells. We hypothesize that biomechanical strain triggers pore formation in SC cells. To test this hypothesis, primary human SC cells were isolated from three non-glaucomatous …

Altered Mechanobiology Of Schlemm’S Canal Endothelial Cells In Glaucoma, Darryl R. Overby, Enhua H. Zhou, Rocio Vargas-Pinto, Ryan M. Pedrigi, Rudolf Fuchshofer, Sietse T. Braakman, Ritika Gupta, Kristin M. Perkumas, Joesph M. Sherwood, Amir Vahabikashi, Quynh Dang, Jae Hun Kim, C. Ross Ethier, W. Daniel Stamer, Jeffrey J. Fredberg, Mark Johnson

Department of Mechanical and Materials Engineering: Faculty Publications

Increased flow resistance is responsible for the elevated intraocular pressure characteristic of glaucoma, but the cause of this resistance increase is not known. We tested the hypothesis that altered biomechanical behavior of Schlemm’s canal (SC) cells contributes to this dysfunction. We used atomic force microscopy, optical magnetic twisting cytometry, and a unique cell perfusion apparatus to examine cultured endothelial cells isolated from the inner wall of SC of healthy and glaucomatous human eyes. Here we establish the existence of a reduced tendency for pore formation in the glaucomatous SC cell—likely accounting for increased outflow resistance—that positively correlates with elevated subcortical …

Arising Applications Of Ferroelectric Materials In Photovoltaic Devices, Yongbo Yuan, Zhengguo Xiao, Bin Yang, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

The ferroelectric-photovoltaic (FE-PV) device, in which a homogeneous ferroelectric material is used as a light absorbing layer, has been investigated during the past several decades with numerous ferroelectric oxides. The FE-PV effect is distinctly different from the typical photovoltaic (PV) effect in semiconductor p–n junctions in that the polarization electric field is the driving force for the photocurrent in FE-PV devices. In addition, the anomalous photovoltaic effect, in which the voltage output along the polarization direction can be significantly larger than the bandgap of the ferroelectric materials, has been frequently observed in FE-PV devices. However, a big challenge faced by …

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo

Graduate Research Posters

Electrospinning is a widely applicable technique that generates non-woven fibers in the micro and nano range. In this project two of its applications are highlighted namely filtration media and enhancement of wettability. The first project demonstrates that electrospinning can be used to produce new fiber filtration media with controlled microstructure. The bimodal and unimodal orthogonal and random filters were made and characterized against their filtration efficiency and pressure drop. Figure of Merit (FOM) was also calculated and discussed. It is shown that the FOM increases when the electrospun fibers are arranged into alternating layers of aligned course and fine fibers. …

Long Life Electrochemical Diodes For Continuous Electrowetting, Mehdi Khodayari, Ben Hahne, Nathan B. Crane

Faculty Publications

The rate of electrochemical reactions in some systems varies with the polarity of the overpotential on the working electrode, introducing diode-like behavior at the electrode/electrolyte interface. However, with repeated bipolar cycling, the electrochemical current damages the electrodes. We have connected electrochemical diodes in series with opposing polarities to reduce the diode current while charging a capacitive circuit. We have previously used this capacitive circuit arrangement to actuate aqueous droplets continuously using the electrowetting (EW) effect. In this study, the performance of electrochemical diodes under repeated voltage cycles is investigated. Aluminum and titanium electrodes in contact with three electrolyte solutions (0.1 …

Capillarity And Two-Phase Fluid Transport In Media With Fibers Of Dissimilar Properties, Thomas M. Bucher Jr.

Theses and Dissertations

Capillarity is a physical phenomenon that acts as a driving force in the displacement of one fluid by another within a porous medium. This mechanism operates on the micro and nanoscale, and is responsible for countless observable events. This can include applications such as absorption in various hygiene products, self-cleaning surfaces such as water beading up and rolling off a specially-coated windshield, anti-icing, and water management in fuel cells, among many others.

The most significant research into capillarity has occurred within the last century or so. Traditional formulations for fluid absorption include the Lucas–Washburn model for porous media, which is …

A Study Of Walkway Safety And Evaluation Of Tribological Test Equipment, Henry Thomas Baker

UNF Graduate Theses and Dissertations

A walkway tribometer measures the coefficient of friction between flooring material and a test foot. The value of the coefficient of friction is an indicator as to whether the flooring surface is slippery and has a propensity to cause slip and falls. This study determined that one style of tribometer, an XL Tribometer, mimics the heel-to-floor interaction of the human heel strike. High speed video footage revealed that the test foot strikes the surface and rotates so that full engagement occurs before sliding thus mimicking the affect of a human ankle. The test foot accelerates forward as would be expected …

The Effect Of Surface Corrosion Damage On The Fatigue Life Of Extruded Aluminum Alloy 6061-T6, Matthew Weber

UNF Graduate Theses and Dissertations

Aluminum alloy 6061-T6 is a common engineering material used in aerospace, automotive, structural applications. Despite its wide use, little has been published about the effects of damage from surface corrosion on its fatigue life. An investigation was performed where 6061-T6 extrusions were exposed to a 3.5% NaCl solution at pH 2 for 2 days and 24 days. The length of time and pH were chosen in order to create distinct surface flaws. The effect of these flaws on the fatigue life was then investigated and analyzed using scanning electron microscopy (SEM) and Weibull statistics. It was determined that samples corroded …

Simultaneous Monitoring Of Singlet And Triplet Exciton Variations In Solid Organic Semiconductors Driven By An External Static Magnetic Field, Baofu Ding, Kamal Alameh

Research outputs 2014 to 2021

The research field of organic spintronics has remarkably and rapidly become a promising research area for delivering a range of high-performance devices, such as magnetic-field sensors, spin valves, and magnetically modulated organic light emitting devices (OLEDs). Plenty of microscopic physical and chemical models based on exciton or charge interactions have been proposed to explain organic magneto-optoelectronic phenomena. However, the simultaneous observation of singlet- and triplet-exciton variations in an external magnetic field is still unfeasible, preventing a thorough theoretical description of the spin dynamics in organic semiconductors. Here, we show that we can simultaneously observe variations of singlet excitons and triplet …

Pitting Corrosion And Corrosion Fatigue Crack Growth Behavior Of Oil-Grade Alloy 718 In Sodium Chloride Solution, Ting Chen

Graduate Theses, Dissertations, and Problem Reports (ETD)

Oil-grade nickel-base alloy 718 has been recently used in the oil and gas industry for downhole drilling components especially for the parts of the bottom hole assembly (BHA) due to its superior mechanical properties, good corrosion resistance, non-magnetic properties and ability to be heat treated to various strength levels. As the modern oil and gas industry explored into coastal and marine locations, deeper and deeper wells have been drilled with high pressure high temperature, making the demand for increased strength and good toughness super critical for alloys used in ultra-deep wells drilling. Moreover, the existence of high concentrations of chloride …

The Collapsible Trailer: Design And Manufacture, Robert Hobson

Biomedical Engineering

No abstract provided.

In-Bottle Wine Aerator, Kevin Kesler, Patrick Lowry, Paul Woolworth

Mechanical Engineering

The proposal for Capitol Cultivators discusses and evaluates the development of an in-bottle wine aerator. It defines the problem and need for an aerator located inside the wine bottle. Additionally, it outlines requirements essential for an effective design and describes the engineering process that will be followed.

Trampoline And Bungee Fatigue-Test Machine, Andy Brock, Christopher D'Elia, Ryan Murphy

Mechanical Engineering

JumpSport, a Saratoga based recreational and fitness trampoline company, sponsored this senior project team towards the development of a fatigue-testing machine. The goal of this project was to iterate the previous machine JumpSport used for bungee cord, spring, and trampoline fatigue testing. Since minimal study had been conducted on these specific bungee cords, the fixture was designed to confirm the theoretical correlations for rubber and perform the final tests according to a strict protocol. Operating with a specific test protocol in mind will allow the data from multiple tests to be combined and analyzed statistically. With a design concept in …

Sodhana Environmental - Final Design Report, Eric Taylor, Corissa Bellis, Cody Perez, Cameron Zeller

Mechanical Engineering

A fully designed cost-effective, sustainable, toilet for the developing world.