Engineering Commons^™

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Electrochemical Impedance Spectroscopy Analysis Of Corrosion Of Reinforcing Steel In Fly Ash Mortar By Means Of Transmission Line Modeling, Padraig Stack

Williams Honors College, Honors Research Projects

Electrochemical impedance spectroscopy (EIS) is an important non-destructive tool that allows for a deeper understanding of the electrochemical processes and mechanisms occurring in an electrochemical cell. Equivalent electrical circuits (EECs) are used to model the impedance data into electrical components, such as resistors and capacitors, on a circuit. Current potentiostat offers software packages that can analyze the frequency response, but the software only supports “simple” EEC that can be written as fixed electrical components in some combination of series and parallel. Park and Macdonald propose a transmission line model (TLM) that does not use lumped-element models, instead, the values of …

A Comparison Between Ultrasonic Guidedwave Leakage And Half-Cell Potential Methods In Detection Of Corrosion In Reinforced Concrete Decks, Ahmad Shoaib Amiri, Ece Erdogmus, Dana Richter-Egger

Durham School of Architectural Engineering and Construction: Faculty Publications

This article presents the advantages and limitations of a recently developed Ultrasonic Guided Wave Leakage (UGWL) method in comparison to the well-known Half-Cell Potential (HCP) method in their ability to detect corrosion in reinforced concrete (RC) bridge decks. This research also establishes a correlation between UGWL data and chloride content in concrete RC slabs. Concrete slabs submerged in a 10% NaCl solution were monitored using both methods over a period of six months. The chloride content from the three cores (0.84, 0.55, and 0.18%) extracted from the slab after the 6-month long process all exceeded the chloride threshold values suggested …

A Novel Structural Health Monitoring Method For Reinforced Concrete Bridge Decks Using Ultrasonic Guided Waves, Ece Erdogmus, Eric Garcia, Ahmad Shoaib Amiri, Michael Schuller

Durham School of Architectural Engineering and Construction: Faculty Publications

This article presents the latest improvements in a recently developed nondestructive testing (NDT) approach for early detection of various flaws (corrosion, delamination, and concrete cracking) in reinforced concrete (RC) bridge decks. The proposed method involves the use of internal steel reinforcement as a wave guide for transmitting ultrasonic waves through the system and the measurement of leaked energy from the surface of the concrete. This paper builds upon the progress made in the previously published phases of the project and aims to further explore the capabilities and practicality of the proposed NDT method. Specifically, the limits of propagation distance, effect …

Detection Of Buried Non-Metallic (Plastic And Frp Composite) Pipes Using Gpr And Irt, Jonas Kavi

Graduate Theses, Dissertations, and Problem Reports

This research investigated alternative strategies for making buried non-metallic pipes (CFRP, GFRP, and PVC) easily locatable using Ground Penetrating Radar (GPR). Pipe diameters up to 12" and buried with up to 4 ft. of soil cover were investigated. The findings of this study will help address the detection problem of non-metallic pipelines and speed the adoption of composite pipes by the petroleum and natural gas industry. The research also investigated the possibility of locating buried pipes transporting hot fluids using Infrared Thermography (IRT).

Results from the study have shown that, using carbon fabric and aluminum tape overlay on non‑metallic pipes …

Effect Of Sintering Temperature On Microstructure, Corrosion Behavior, And Hardness Of Nanocrystalline Al-5at.%Ni And Al-5at.%V Alloys, Matthew G. Wachowiak

Williams Honors College, Honors Research Projects

The purpose of this project was to investigate thermal stability of high energy ball milled Al-5at.%Ni and Al-5at.%V alloys. Characterization was done by analyzing grain size and solid solubility. Samples were created using high energy ball milling, cold compaction to 3 GPa, and sintering from 100 °C to 500 °C at 100 °C increments, as well 450 °C and 614 °C. Microstructure, mechanical properties, and corrosion properties were determined using scanning electron microscopy, energy dispersive x-ray spectroscopy, x-ray diffraction, hardness testing, and cyclic potentiodynamic polarization. Vickers hardness of Al-5at.%Ni decreased with increasing temperature. For Al-at.%V, hardness increased with sintering temperature …

Process Refinement Through Design Of Experiments (Taguchi) To Reduce Porosity Levels Of Thin Flame Spray Nicrbsi Coatings On Cast Aluminium Alloys, David Culliton, David Kennedy, Tony Betts

Conference Papers

Thin(16matrix of key deposition parameters was constructed to develop the optimum spray parameters. The effects of parameter variations on the porosity levels of these coatings were assessed. Key parameter interactions were reported. Quantifiable interactions between the selected parameters were noted for the LM24 substrate. However, on the LM25 substrate these interactions were much less defined. Corrosion performance of the optimised coatings, based on electrochemical impedance spectroscopy, was reported. The presence of through-pores in the coatings were shown to reduce the corrosion resistance of the coated systems by a factor of 10, in dilute NaCl solutions, compared to bulk 316L stainless …