Engineering Commons^™

Additive Manufacturing Of Variable Contrast Computed Tomography Anatomical Phantoms Using A Single Feedstock In Fused Filament Fabrication, Cory J. Darling

University of New Orleans Theses and Dissertations

Anatomical phantoms used in biomedical education and training benefit greatly from Fused filament fabrication’s (FFF) ability to rapidly produce complex and unique models. Current materials and methods used in FFF have limited ability to accurately produce phantoms that can mimic the radiological properties of multiple biological tissues. This research demonstrates that the CT contrast of FFF produced models can be modified by varying the concentration of bismuth oxide in acrylonitrile butadiene styrene (ABS) filaments and a tunable CT contrast that mimics the CT contrast ranging from fatty tissue to cortical bone using a single composite filament without introducing artificial image …

Cost-Effective Non-Destructive Testing Of Biomedical Components Fabricated Using Additive Manufacturing, Santiago Fabian Cobos

Electronic Thesis and Dissertation Repository

Biocompatible titanium-alloys can be used to fabricate patient-specific medical components using additive manufacturing (AM). These novel components have the potential to improve clinical outcomes in various medical scenarios. However, AM introduces stability and repeatability concerns, which are potential roadblocks for its widespread use in the medical sector. Micro-CT imaging for non-destructive testing (NDT) is an effective solution for post-manufacturing quality control of these components. Unfortunately, current micro-CT NDT scanners require expensive infrastructure and hardware, which translates into prohibitively expensive routine NDT. Furthermore, the limited dynamic-range of these scanners can cause severe image artifacts that may compromise the diagnostic value of …

A Highly Conductive, Flexible, And 3d-Printable Carbon Nanotube-Elastomer Ink For Additive Bio-Manufacturing, Andy Shar, Phillip Glass, Daeha Joung Ph.D.

Undergraduate Research Posters

The synthesis of a highly conductive, flexible, 3D-printable, and biocompatible ink has been of great interest in the field of bio-based additive manufacturing. Various applications include ultra-sensitive, microscale tactile sensors, patient-customizable scaffolds for cardiac and nerve tissue regeneration, and flexible electrocardiogram (ECG) electrodes. Here, a novel elastomeric carbon nanocomposite is presented consisting of amino-functionalized carbon nanotubes (CNT-NH₂) homogenously dispersed in a one-part room-temperature vulcanizing (RTV) silicone matrix. The use of acetone as a swelling solvent aids in electrical percolation through the elastomer matrix. CNT-NH₂ ratios can be tuned to fit various needs; higher tensile strength is favored …

3d Printing In Low Resource Healthcare Settings: Analysis Of Potential Implementations, Alenna Beroza

Dissertations, Master's Theses and Master's Reports

3D printing has gained significant momentum in the past ten years, and its unique advantages make it especially ideal for use in low resource healthcare settings, where many designs have already been successfully implemented. Yet, little has been studied on how 3D printing can be sustainably and functionally implemented in low resource healthcare systems as a manufacturing practice. In this report, three business models are proposed for this implementation: In-House Operator, Independent Operator, and Print Farm. These models were then tested over four months in Kisumu county, Kenya, at two workshops and seven public hospitals. I worked with local medical …

Nanotechnology And Additive Manufacturing Platforms For Clinical Medicine: An Investigation Of 3d Printing Bioactive Constructs And Halloysite Nanotubes For Drug Delivery And Biomaterials, Jeffery A. Weisman

Doctoral Dissertations

Personalized medicine requires the development of new technologies for controlled or targeted drug delivery. Three-dimensional (3D) printing and additive manufacturing techniques can be used to generate customized constructs for bioactive compound delivery. Nanotechnology in the form of nanoparticles, used as a stand-alone construct or for material enhancements, can significantly improve established biomaterials such as PMMA based bone cements or enable new technology to have enhanced capabilities. Combinations of the technologies can be used in such applications as infectious disease treatments, chemotherapeutic targeted drug delivery or targeted delivery of nearly any bioactive compound.

Chemotherapeutic or antibiotic enhanced 3D printing filaments were …