Engineering Commons^™

Film Boiling From Inclined Flat Surfaces, Charles Ernest Price

Masters Theses

"The object of this investigation was to determine the effect of inclination on the heat transfer for saturated film pool boiling from a flat plate heater. Nitrogen at atmospheric pressure was used as the test fluid. The test plate was oriented at various angles from the horizontal position and the convective film coefficient was determined for each angle. Tests were conducted for heater angles of 0°, 30°, 60°, and 90°. The heater strip was placed in a container of the liquid and was heated electrically. Heat transfer results were obtained for plate temperatures ranging from 100 to 800°F. As the …

A Computerized Method For Finding The Dynamic Response Of Multi-Mass Systems With Damping To Arbitrary Inputs, Bakulesh Balbhadra Patel

Masters Theses

"A practical procedure for the systematic application of Foss's method to the solution of multi-degree-of-freedom damped systems is presented. It is relatively easy to determine the response of classically damped systems to various inputs. For non-classically damped systems the method proposed by K. A. Foss has been employed. This method gives an exact and complete solution for the response of linear multi-mass damped systems subjected to arbitrary inputs. Since the method requires lengthy and complex computations, the use of a digital computer is essential. In order to obtain the complete response of a multi-mass damped system to both sinusoidal and …

Apparatus And Techniques For The Plane Wave Analysis Of Acoustic Filters, Victor Hugo Simon

Masters Theses

"This thesis describes a method for determining the reflection and transmission characteristics of acoustic filters under static (i.e. no flow) conditions. These characteristics are obtained by the combination of linear plane wave acoustic theory with a sequential experimental procedure. The experimental data necessary for the calculation of the reflection characteristics were obtained from measurements made on the inlet side of the filter with a standing wave tube apparatus. In order to calculate the transmission characteristics of the filter, the standing wave measurements were augmented with measurements taken on both the inlet and outlet side of the filter. This was accomplished …

Investigation Of Free Convection Heat Transfer From An Inclined Flat Plate, Phairojna Sang-Urai

Masters Theses

"The experimental investigation was conducted to determine temperature distribution and convective heat transfer coefficients in terms of Nusselt number for an inclined heated flat plate in air. The heated surface of the aluminum flat plate was set facing upward and moved through seven positions from the vertical to the horizontal. The investigation shows that the local Nusselt number can be predicted by Kiekus's solution within 12 per cent for inclination angles from the vertical through 75° from the vertical. In the case of the vertical position, Eckert's solution gives a better prediction. For the horizontal position the results show good …

Application Of Approximate Transmission Matrices To Describe Transverse Beam Vibrations, Ranjit Kumar Roy

Masters Theses

"This paper is a report of an investigation of an approximate method for finding the principal mode frequency roots for beams in transverse vibration. The method utilizes approximate transmission matrices obtained by a power series expansion of the basic differential equation which governs the transmission matrix. Investigation has been carried out to examine the efficiency of the method in producing the first several normal mode frequency roots. This has been achieved by applying the method to several uniform and non-uniform beams and comparing the results with the exact solutions. The technique has further been applied to non-uniform beams of tapered …

A Theoretical Analysis Of The Free Vibrations Of A Clamped Circular Plate With Damping, Bhalchandra Krishnaji Vaidya

Masters Theses

"A theoretical analysis of the free vibrations of a clamped circular plate was undertaken. The effects of transverse shear were considered for application to relatively thick plates in which there exist sharp transients and frequencies corresponding to higher modes. The method adopted by R. D. Mindlin was used to develope [sic] the differential equation of motion for the plate. The damping effect due to the resistance of the medium in which the plate vibrates was also considered. This damping was assumed to be due to the generation of pressure waves caused by the displacement of the plate...Since the solution requires …

The Use Of Turbulence Energy Equation In Boundary Layer Study, Ro-Chi Tai

Masters Theses

"A turbulent boundary layer problem has been studied analytically and compared with an available experiment in the literature. Correlations of the experimental data were made to investigate the validity of the commonly used empirical relations on turbulent shear stresses. It was found that the model which related the local turbulent shear stress linearly with the local turbulent kinetic energy, as used by Bradshow et. al., appeared to be most reasonable. combining this model with the expression of turbulent viscosity given by Boussinesq, it was then possible to introduce the turbulence-energy equation in addition to the governing equations of continuity and …

Experimental Determination Of Dynamic Properties Of Aluminum Including Poisson's Ratio, Terry Lee Holman

Masters Theses

"Two rods of 7075-T651 aluminum are longitudinally impacted to investigate the material's dynamic properties. The test rod, initially at rest, is instrumented with strain gages to record the strain-time history after the impact rod, accelerated to uniform velocity by an air gun launcher, strikes the test rod. A camera records the strain-time pattern displayed on an oscilloscope. The experiment indicates a consistent rise time of approximately 9 µsec. Simple one-dimensional theory correlates well with the experimental data. Compensation is included for the transverse sensitivity of the gages used. The dynamic values for both the modulus of elasticity and Poisson's ratio …

A Comparison Of Lumped Parameter Models Commonly Used To Describe One-Dimensional Vibration Problems, Suresh Kumar Tolani

Masters Theses

"Three lumped parameter model representations of the one-dimensional uniform continuous system in a vibration state are examined. The exact (continuous) solutions were used as a reference to evaluate the accuracy of the results obtained via these discrete element models. The model comparisons, carried out for both the principal modes and the systems under forced excitations, are based on the maximum strain energy. The effect of varying the number of segments in the model representation showed improvement in approximating the exact strain energy solution as the number of segments was increased. In general, the results of the model comparisons based on …

Dynamic Response Of A Gyrocompass, Subhash Govind Kelkar

Masters Theses

"A gyrocompass with three degrees of freedom is studied and an attempt made to solve the exact equations of motion numerically. The equations are obtained by using the Lagrange formulation of the problem. The kinetic energy and the potential energy of the system are determined from the energies of the various components. These are then substituted into Lagrange's equation to obtain the three equations of motion for the three angular coordinates. As few restrictive assumptions as possible are made during this development. From these exact equations of motion an approximate analytical solution is obtained by making several assumptions and then …

The Design Of A Direct Current Generator Field Controller, Melvyn Elwin Downs

Masters Theses

"A controller was built utilizing transistors and silicon controlled rectifiers to allow torque control of the General Electric dynamometer, type TLC-50. The current gain of the controller was approximately 10⁶ such that the field current could be controlled by an input current of zero to approximately two microaaperes. The transfer function for the controller-dynamometer system was experimentally determined. The results indicate that the gain of the open loop torque control system is constant for frequencies up to 1.1 radians per second. Satisfactory values of gain for proportional and proportional plus integral control, were experimentally determined by operating the closed loop …

Dynamic Response Of Circular Plates To Transient And Harmonic Transverse Loads Including The Effect Of Transverse Shear And Rotary Inertia, Perakatte Joseph George

Doctoral Dissertations

"Using an improved theory of plate vibration suggested by R. D. Mindlin which takes into account the effects of transverse shear and rotary inertia, free and forced transverse vibrations of uniform circular plates are studied and the results compared with those obtained using the classical theory of plate vibration. The governing equations are developed in polar coordinates using the equations of elasticity. Frequency equations for axisymmetric and antisymmetric vibrations are derived for solid circular plates under different boundary conditions and for an annular plate rigidly mounted on a shaft. The response of plates to different types of rapidly applied axisymmetric …

A Finite Element Method For Geometrically Nonlinear Large Displacement Problems In Thin, Elastic Plates And Shells, Ronald August Melliere

Doctoral Dissertations

"A finite element method is presented for geometrically nonlinear large displacement problems in thin, elastic plates and shells of arbitrary shape and boundary conditions subject to externally applied concentrated or distributed loading. The initially flat plate or curved shell is idealized as an assemblage of flat, triangular plate, finite elements representing both membrane and flexural properties. The 'geometrical' stiffness of the resulting eighteen degree-of-freedom triangular element is derived from a purely geometrical standpoint. This stiffness in conjunction with the standard small displacement 'elastic' stiffness is used in the linear-incremental approach to obtain numerical solutions to the large displacement problem. Only …

Test 1001: Ford 4000, 4600 And 4610 8-Speed Gasoline (Also Ford 4000 Gasoline Row Crop And Super Utility), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 999: Ford 4000 Gasoline Select-O-Speed (Also Ford 4000 Gasoline Select-O-Speed Row Crop), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 997: Ford 5000 Gasoline Select-O-Speed (Also Ford 5000 Gasoline Select-O-Speed Row Crop), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 998: Ford 5000 Gasoline 8-Speed (Also Ford 5000 Gasoline 8-Speed Row Crop And Ford 6600 Gasoline 8-Speed), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 994: Ford 4000 Diesel 8-Speed (Also Ford 4000 Diesel 8-Speed Row Crop And Ford 4000 Su Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1000: Ford 5000 Diesel Select-O-Speed (Also Ford 5000 Diesel Select-O-Speed Row Crop), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 996: Ford 5000 Diesel 8-Speed (Also Ford 5000 Diesel 8-Speed Row Crop), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 995: Ford 4000 Diesel Select-O-Speed (Also Ford 4000 Diesel Select-O-Speed Row Crop), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 993: John Deere 2520 Power Shift, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 992: John Deere 2520 Syncro Range, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 991: John Deere 1520, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 986: Oliver 2150 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 987: Oliver 2050 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

A Study Of Thermoacoustic Oscillations At Elevated Static Pressures, Michael Einar Berger

Mechanical Engineering ETDs

An experimental investigation was conducted to determine the effect of high static pressure on a closed thermoacoustic sound generator.

The theory for thermoacoustic oscillations is reviewed and analyzed for the case of elevated static pressure. Design equations for high internal pressure oscillators are developed from the principles of dimensional analysis, and a general de­sign equation is proposed.

A closed double-end thermoacoustic oscillator was designed to withstand high temperatures and pressures and was used in the experimental investi9ation. Both air and helium were used as the working gases.

The results of both the theoretical and experimental investigations show that acoustic sound-pressure …

Test 985: International 444 (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 983: International Farmall 544 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 984: International Farmall 544 (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …