Engineering Commons^™

Report On The School Of Mechanical Engineering National Technical Center Saigon, South Vietnam, Myrne R. Riley

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

"Training in the discipline of Mechanical Engineering is offered in South Vietnam by the School of Mechanical Engineering, one of four engineering schools and a Merchant Marine School composing the National Technical Center located presently in the Phu Tho region of Saigon, South Vietnam. The school was established in 1956 for the training of engineers, for mechanical and industrial activities. It became part of the National Technical Center, established by Decree No. 213-Gd by the President of the Republic of Vietnam on June 29, 1957 and graduated the first class of 20 in the summer of 1960. The KS Degree, …

Experimental Investigation Of Shock Boundary Layer Interaction For Two-Dimensional And Axisymmetric Flow, A. Shawki Zahran

Electronic Theses and Dissertations

A supersonic wind-tunnel has been constructed using an 8 inch by 10 inch single stage jet vacuum ejector with a capacity of handling 0.4 lb/sec air at 4 inches Hg absolute suction pressure. A Toepler Schlieren system with 10-inch diameter parabolic mirrors has been set up for flow pattern visualization. The same apparatus was developed to obtain multi-colored views of the flow pattern. That was accomplished by placing an equilateral prism in front of the light source located at the focal plane of the first parabolic mirror. A spectrum was thus produced at the focal plane of the second parabolic …

Floating Bubble Configurations, Robert A. Medrow, B. T. Chao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The configurations of bubbles floating at a vapor-liquid interface are investigated both analytically and experimentally. The differential equations governing the shape of a single bubble at rest in a liquid of infinite extent are deduced under the assumption of zero dome thickness, uniform surface tension, and equal gas densities within the bubble and above the interface. These equations show that nondimensional bubble shapes depend upon the value of a single parameter. An analytical solution, valid for small bubbles, is developed and shown to be in good agreement with the general numerical solution. Good agreement with theory is demonstrated for floating …

Heat Transfer From An Oscillating Horizontal Wire, Bassem F. Armaly, D. H. Madsen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The effect of vibration on heat transfer by natural convection has been investigated experimentally using a thin wire, 0.010 in. in diameter, and air as a convection medium. Horizontal reciprocating motion of varying amplitudes, peak-to-peak values of 0-2.655 in., and frequencies, 0-20 cps, was applied to an electrically heated horizontal wire. The average wire velocity (frequency times total path length traveled per cycle by the wire) was used to correlate and predict the experimental results. © 1971 by ASME.

Density Distribution Measurements In Rarefied Gases Contained Between Parallel Plates At High Temperature Differences, Darryl J. Alofs, Richard C. Flagan, George S. Springer

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Density Distributions Were Experimentally Determined in Rarefied Gases at Rest Contained between Two Parallel Plates Maintained at Widely Different Temperatures. the Temperatures of the Hot and Cold Plates Were ∼79°K and ∼294°K, Respectively, Resulting in a Temperature Ratio of About 4:1. Both Helium and Nitrogen Were Used as Test Gases. Particular Attention Was Focused on Obtaining Data in the Temperature Jump and Transition Regimes. the Gas Densities Were Measured by Observing the Luminescence Produced by a High-Energy Electron Beam Traversed between the Plates. in Addition to the Density Measurements, Heat Transfer Measurements Were Also Made in Order to Estimate the …

The Axial Contact Of Finite Elastic Cylinders With Application To Thermal Contact Resistance, Ross Orlo Mcnary

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Predictions of the macroscopic thermal contact resistance have been severely restricted because the macroscopic contact area between finite members could not be determined. A new method of solution to this contact problem in elasticity is developed which is applicable to a wide variety of geometries and boundary conditions. A physical lumped-parameter model is employed from which the finite difference equations in terms of displacement are derived. Calculations using this method indicate that large errors in the prediction of the thermal contact resistance can result if solutions for bodies of infinite extent are employed for finite regions of interest. Especially large …

Charges On Jet Drops Produced By Bursting Bubbles, Robert A. Medrow, B. T. Chao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The sizes and charges of jet drops produced by bursting air bubbles are examined experimentally. The variation in charge for bubble lifetimes of up to 200 sec in NaCl and KCl solutions is reported. Jet drops refer to drops produced by a jet rising from a cavity left in a liquid surface by a bursting bubble; bubble lifetime is the interval during which a bubble is in motion between generation and rupture. With other variables held constant, drop charge shows a characteristic variation of a rise to a maximum followed by a decrease to an asymptotic value, as bubble lifetime …

Test 1068: Case 970 Power Shift Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1069: Minneapolis-Moline G-1350 Diesel (Also Oliver 2155 Diesel) 10-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1071: Kubota L-210 Diesel 6-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1066: Case 1070 And 1090 Power Shift Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1074: Deutz 8006 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1077: Case 870 Manual Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1083: International Farmall 1066 Hydrostatic Turbo Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1078: Case 970 Manual Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1081: International Farmall 1066 Turbo Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1082: International Farmall 966 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1086: Massey-Ferguson Mf 1500 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1064: John Deere 4620 Power Shift, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1072: Kubota L-260 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1075: Deutz 4006 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

The Influence Of Member Length On Thermal Contact Resistance In A Vacuum Environment, Larry Martin Cooper

Masters Theses

"An investigation was conducted to determine the influence of member length on thermal contact resistance in a vacuum environment. A model was created which consisted of a center rod axially loaded between two other members. It was assumed that circular macroscopic constriction areas were formed at the contact interface when the rods were loaded. Macroscopic modeling of the contact surfaces makes the thermal contact analysis a function of the mechanical and thermal boundary conditions of the total body. The method of finite differences was employed to calculate the temperature distribution, heat flows, and thermal contact resistance of each member. Data …

Test 1063: John Deere 7020, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1073: John Deere 4620 Syncro Range, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1084: John Deere 2030, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1085: John Deere 2030/John Deere 2440, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1067: Case 1070 And 1090 Manual Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1076: Case 870 Power Shift Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1079: Steiger Bearcat Diesel 10-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1080: International Farmall 1466 Turbo Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …