Engineering Commons^™

An Investigation Of A Free Jet At Low Reynolds Numbers, George C. Greene

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis presents a comparison of the measured and calculated flow field properties of a nozzle of unusual design which was used to produce an incompressible, low Reynolds number ]et. The "nozzle" is essentially a porous metal plate which covers the end. of a pipe. Results are presented for nozzle Reynolds numbers from 50 to 1000 with velocities of 100 or 200 ft/sec. The nozzle produces s, uniform velocity profile at nozzle Reynolds numbers well below those at, which conventional contoured nozzles are completely filled with the boundary layer. A Jet mixing analysis based on the boundary layer equations accurately …

Computer-Aided Design Of Light Aircraft To Meet Certain Aerodynamic And Structural Requirements, Joanne Lynn Walsh

Mechanical & Aerospace Engineering Theses & Dissertations

Nonlinear mathematical programming techniques are applied to a particular aircraft design problem, that of determining the maximum range design for light aircraft subject to certain aerodynamic and structural requirements. Search techniques available in an existing nonlinear optimization computer program, AESOP, are applied to the design problem. Seven design variables are used to define the wing dimensions, the wing skin thickness, the cruise velocity, the amount of fuel carried, and the engine horsepower. The influence of different design requirements on the range is observed and discussed.

Long-Term Retention Of Tritium In Man, Chin-Jen Ou

Electronic Theses and Dissertations

[No abstract provided.]

The Formation And Properties Of Machining Burrs, Laroux K. Gillespie

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The formation of burrs in Machining Operations occurs by three Basic Mechanisms:

1) Lateral Extrusion of material

2) Bending of the chip

3) Tearing of the chip form the workpiece

Each of these mechanisms has been studied analytically and compared to experimental results. The agreement between predictions and measurements has been found to be close.

Drilling, milling, grinding, and turning burrs were produced in 303Se stainless steel and their properties were related to tool geometry, feedrates, and depth of cut. One thousand measurements were made and subsequently analyzed by analysis of variance techniques. The properties measured include burr length and …

Numerical Study Of The Turbulent Boundary Layer In A Hypersonic Nozzle, Joan Patricia Gosink

Mechanical & Aerospace Engineering Theses & Dissertations

A numerical study of the turbulent boundary layer in a hypersonic nozzle is presented. The boundary layer equations are solved by a second order, implicit finite difference scheme developed at Langley Research Center. The technique is applicable to laminar, transitional or turbulent compressible or incompressible boundary layer flows for planar or axisymmetric geometries. A technique is presented for utilizing experimental data to start the finite difference solution.

Turbulent boundary-layer measurements on axisymmetric nozzle walls at Mach number 6 are presented and compared with numerical predictions obtained by starting the solution in the stagnation chamber and from a downstream experimental station. …

Transient Convective Heat Transfer In Closed Containers During And After Gas Injection, Jennings Donell Means

Theses and Dissertations

This dissertation presents experimental data correlations for the spatially - averaged convective heat transfer coefficient for thin walled closed containers during and after gas injection. The different modes of heat transfer were identified, and correlations were made for each. Correlations are presented for the injection period, post-top injection, post-bottom injection, post- tangential, post-radial injection, and post-ejection heat transfer for various tank geometries. Of special significance are the very high heat transfer rates that were shown to be present in some cases immediately after injection. Heat transfer rates were shown to be, for a short period, up to almost two orders …

Analysis Of Heat Generation And Temperature In High Speed, High Temperature Bearing Balls, Hans R. Ringger

Theses and Dissertations

This thesis reports an investigation of the generation of heat on, and the prediction of temperature of high-speed, dry-film lubricated, stainless steel bearing balls.

The Design And Analysis Of An Electro-Pneumatic Signal Converter, Richard K. Thornton

Theses and Dissertations

In the field of process control it is desirable to study dynamic characteristics such as frequency response and distortion when determining just how equipment is to be controlled. Pneumatic controllers, transmitters, control valves, etc., all have dynamic behaviors which can be expressed mathematically as transfer functions. Each component plays an important role in determining the entire system behavior. Frequency response is one technique used in developing a component’s transfer function. By driving a device with a sinusoidal signal of fixed amplitude and frequency the output amplitude and phase shift are measured and compared with that of the input. Varying the …

Finite Conductance Element Method Of Conduction Heat Transfer, E. Clark Lemmon

Theses and Dissertations

One of the basic goals in engineering is to formulate models which will provide a means for analytically predicting observed phenomenon. For some time, the partial differential equations describing the steady state and transient conduction of heat within a solid have been available. However, the straight forward use of these equations is often restricted due to the surface geometry of the solid. If the surface geometry is at all irregular, exact solutions will in general not exist. In that case, a solution is sought by some approximate numerical technique. The two techniques most often used are the finite difference method …

An Aerodynamic Investigation Of The Causes Of Overhead Electrical Transmission Line Gallop, Eric Nathan Skousen

Theses and Dissertations

Overhead electrical transmission lines vibrate due to the action of a prevailing wind. These cable vibrations can be classified into two categories— high-frequency and low-frequency. The high-frequency vibrations, "aeolian" vibrations or "singing wires," is a low-amplitude phenomenon. It has been largely controlled with the use of various mechanical dampers [l, 2],

Measurement And Analysis Of Data In Turbulent And Transition Regions Of Two-Phase Flow, Akula Venkatram

Theses and Dissertations

The main aim of the project was to examine the possibility of using the hot wire anemometer to detect particles in a fluid. It was hoped that the presence of the particles would affect the autocorrelation plot and the energy spectrum of the velocities measured in the fluid.

Heat Transfer In Intrinsic Thermocouples;Application To Transient Temperature Measurement Errors., Ned R. Keltner

Mechanical Engineering ETDs

The use of intrinsic thermocouples to measure rapid temperature variations of electrically conductive materials has become increasingly popular because of their unique characteristics: rapid response, versatility, reliability, relative simplicity and low cost. However, in some of the applications, the variations are so rapid that the heat transfer process between the substrate and the thermocouple wire induces large errors in the temperature measurements. In these situations, proper interpretation of the experimental data required an accurate description of the response characteristics of the thermocouple.

Test 1131: Deutz D 4506 And 4507 Diesel (Also Deutz-Fahr D-4507 Diesel) 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1138: David Brown 1212 Diesel (Also Case 1210 Power Shift Diesel) 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1148: Case 1370 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1136: David Brown 995 Diesel (Also Case 995 Diesel) 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

De Los Sealabs A Los Skylabs, Aldemaro Romero Jr.

Publications and Research

No abstract provided.

¿Respiraremos Algún Día El Agua Del Mar?, Javier Gimeno, Aldemaro Romero Jr.

Publications and Research

No abstract provided.

Test 1119: Alis-Chalmers 7030 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Nonequilibrium Structure Of Argon Shock Waves, Harlan F. Nelson

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This theoretical study investigates the influence of (1) the nonequilibrium excited state population in the relaxation region and (2) line radiation in the precursor on shock wave structure by considering strong shock waves propagating at Mach 18 and 24 into a theoretical argon-like gas at a pressure of 1 cm Hg and a temperature of 300°K. The argon atom is modeled as having two bound states plus a continuum, and the calculations include finite atom-atom and electron-atom collisional ionization and excitation rates as well as continuum and line radiation. The electron gas is allowed to be at a different temperature …

Engineering And Scientific Manpower- A Scarce Resource For The 1970'S, Merl Baker

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Rock Fragmentation By Subsurface Thermal Inclusions - A Finite Element Study, Mahendrakumar Ramkrishna Patel

Doctoral Dissertations

"Although rock tunneling machines are being used extensively with performance and cost advantages over traditional drill and blast methods, their usefulness for hard rock excavation is far from being practical due mainly to the inability of present day mechanical cutters to penetrate these rocks economically. Among various novel techniques that are being investigated, internal heating methods seem to be the most promising. This investigation is concerned with a feasibility study of thermal rock fragmentation using heat to create in-depth thermal inclusions.

The three-dimensional problem of in situ rock fragmentation involves parallel rows of equidistant holes drilled to a constant depth. …

Test 1120: Allis-Chalmers 7050 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1121: Ford 8600 Diesel Dual Power, Ford 8600 Diesel Dual Power Row Crop, Ford 8600 Diesel 8-Speed All Purpose And Ford 8600 Diesel 8-Speed Row Crop, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1123: International 966 Diesel 16-Speed (Chassis S/N 2510161u017000 And Up), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1125: International 1466 Turbo Diesel (Also International 1486 Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1134: Massey-Ferguson 1155 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1122: Ford 9600 Diesel Dual Power, Ford 9600 Diesel Dual Power Row Crop, Ford 9600 Diesel 8-Speed All Purpose And Ford 9600 Diesel 8-Speed Row Crop, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1135: Massey-Ferguson 1135 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 1129: International 674 Utility And 674 Row Crop (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …