Engineering Commons^™

Test 1263: John Deere 4840 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1265: John Deere 4440 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Ole Miss Engineer 1976

Ole Miss Engineer

No abstract provided.

Sensitivity Of Process Variables On Rigid Polyurethane Foaming, Bruce A. Pugsley

Theses and Dissertations

Inadequate understanding and/or control of the polyurethane rigid foam process normally requires five to ten percent overpack of cavities to obtain correct fill and foam characteristics. This practice of overpacking has resulted in excessive waste and cost.

Propagation Of Ground Vibration: A Review, Timothy G. Gutowski, Clive L. Dym

All HMC Faculty Publications and Research

A review of the current state of the art of ground vibration propagation is presented herein. First the theoretical models of vibration attenuation are reviewed and then measurement techniques are discussed. Finally, measurement and theory are combined into predictive models, whose validity is discussed.

Test 1229: Allis-Chalmers 7580 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Comparative Residential Energy Consumption And Fuel Costs With Various Types Of Systems: Oil-, Gas-, Electric-Furnaces And Heat Pumps, Ronald Hunter Howell, Harry J. Sauer Jr.

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

The electric air-to-air heat pump for residential heating offers an economic alternative to systems traditionally used extensively for home heating, such as, oil or gas fired furnaces and electric resistance heat. This simulation analysis showed that using 1976 mid- Missouri fuel costs, an oil fired furnace was the least expensive to operate of the three traditional type residential heating units. LP gas heating was 19% higher than oil heat while electric resistance heating was 26% higher in cost than oil. The typical air-to- air heat pumps showed a 29% reduction in the heating bill when compared to an oil furnace.

Ole Miss Engineer 1976

Ole Miss Engineer

No abstract provided.

Evaluation Of Upwelling Infrared Radiance In A Nonhomogeneous Nonequilibrium Atmosphere, Sundaresa Venkata Subramanian

Mechanical & Aerospace Engineering Theses & Dissertations

The primary purpose of this study was to investigate the influence of vibrational nonequilibrium upon upwelling infrared radiance from the earth's atmosphere. Basic equations are presented for calculating the atmospheric transmittance, heating rates, and equilibrium and nonequilibrium upwelling radiances. By employing the Lorentz line-by-line model for spectral absorption, heating rates and upwelling radiances were calculated for equilibrium as well ·as nonequilibrium conditions in the spectral range of 4.6 μ CO and 3.3 μ 'CH₄ bands. For the spectral range of CO fundamental band, the influence of different 1~arameters on the upwelling radiance was also investigated. The results indicate that …

Elastic-Plastic Analysis Of A Flat Ring Subject To Internal Pressure, Wei-Yang Warren Lu

Mechanical Engineering ETDs

An exact elastic-plastic solution for the stresses in a flat ring subject to pressure is obtained on the basis of J₂ deformation theory together with a modified Ramberg-Osgood law. The results are assessed on the basis of Budiansky's criterion for the acceptability of J₂ deformation theory. By using exact elastic-plastic stresses, the radial enlargement and the permanent increase in thickness of the ring at the hole are obtained. Upon release of the pressure, residual stresses around the hole are produced.

The Analysis Of The Deflection And Containment Of A Hot Plume By Side Draft Exhaust Hooding, Douglas H. Macgowan

Dissertations and Theses

A common industrial ventilation and pollution problem results when a thermally buoyant polluted plume of air must be exhausted away from a work area to allow achievement of air pollution standards. Generally, a close fitting canopy hood is one of the most effective means of exhaust containment; however, physical restrictions or the operation itself often prevent such an arrangement, and a hood located to the side of the operation is required. This arrangement requires the exhaust to bend and contain the vertically rising plume with a horizontal sweep of exhaust air across the surface of the operation.

A review of …

Test 1211: Case M-B 4/94 Diesel (Unimog), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Analysis Of A Heat Pipe Heat Exchanger, Joseph Olorunfemi Amode

Mechanical Engineering ETDs

One of the more promising applications of the heat pipe is in heat exchangers. Heat pipe heat exchangers may be used as recuperators in heating and ventilating systems, in gas turbines, in steam power plants, and in various process industry applications.

An analysis of the heat pipe heat exchanger was conducted in order to help optimize its performance. A computer program was developed to predict heat pipe performance, finned-tube heat exchanger performance, and the overall per­formance of a finned-tube heat pipe heat exchanger. The computer analysis uses conventional heat exchanger design techniques and a new heat pipe design technique which …

Ua64/3 Readout, Wku Industrial Education & Technology

WKU Administration Documents

Newsletter includes articles:

• Construction Complete on Environemental Science & Technology Building
• Wendt, Donald. Some Reflections on teh Kentucky Industrial Education Association
• Tomazic, Norman. Technology Assessment A Step Toward a Humanized Technology
• Frank Pittman has Individualized Course Published
• Lowrey, H.J. Industrial Arts in a Changing Society
• H.B. Clark
• Growing Interest, re: Architectural Drafting
• Old Building Begins Renovation
• Walter Nalbach: Craftsman at Home

Ole Miss Engineer 1976

Ole Miss Engineer

No abstract provided.

Similitude Of Mass Transfer Processes In Distorted Froude Model Of An Estuary, Carvel Hall Blair

Mechanical & Aerospace Engineering Theses & Dissertations

The project began with the design and construction of a hydraulic Froude model of the Lafayette River, a small well mixed estuary in Norfolk, Virginia. Horizontal scale is 1/540, vertical scale 1/12 yielding a vertical distortion of 45. Adjustment by roughness strips and screens produced close agreement of model-prototype tide heights, currents, and salinities in the deep reaches comprising 80% of the estuary volume. Some scale effect in velocity and tide height could not be eliminated in the shallow upper branches of the estuary, probably because of the high geometric distortion and the narrowness of the channel at kilometer 6.7. …

An Improved Fission Product Pressure Model For Use In The Venus-Ii Disassembly Code, Ray Leland Jensen

Theses and Dissertations

The world's growing need for safe, reliable, and long-term energy sources has intensified the research being conducted in the development of nuclear power. The operation of power reactors is contingent upon the continued availability of the fissile material required to maintain a critic a l reactor. The only naturally occuring fissile material is an isotope of uranium, U-235, which only accounts for 0.76 percent of the uranium that is mined. Due to the relative scarcity of this important fissile material it is estimated the United States' sources of economically recoverable fissile material will be delinquished with in about twenty-five years.^1

Steady-State Fluidics: Computer-Aided Analysis Of Analog Fluidic Circuits By Use Of Experimentally Determined Characteristic Curves, Raymond P. Martin Jr.

Theses and Dissertations

One of the fundamental tasks confronting engineers is the transmission and control of energy. The engineer, faced with this requirement and influenced by details of a specific, situation, his education and experience, and the customer's desires, will probably select a mechanical, electrical, or electro-mechanical system. Often a better choice exists—the use of a fluid power system. Fluid power systems employ pressurized fluids, liquids and/or gases, to transmit and control energy. Hydraulic systems use liquids, usually special oils or treated water. Pneumatic. systems use air or other gases. Both types are versatile and find a wide range of application.

3rd Annual Umr-Mec Conference On Energy -- Entire Proceedings, University Of Missouri--Rolla

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

No abstract provided.

Test 1218: Case 1570 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1226: Ford 3600 And 3610 Gasoline 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1224: Ford 6600 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1221: Ford 3600 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Predicting Natural Frequencies Of A Hydrodynamically Lubricated Journal Bearing With Constant Oil Supply Pressure, D. C. Edwards, N. Khorzad, Charles L. Edwards

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The analytical and experimental investigations reported here deal with the natural frequencies and system behavior of a full journal bearing subjected to a small sinusoidal load superimposed on a large unidirectional static load. The analysis, verified by experimentation, shows that the bearing can be regarded as two independent second-order systems acting perpendicular to each other. The variable coefficients of the equations of motion cause the bearing to behave as an underdamped system for low values of static eccentricity ratio to, and as an overdamped system for intermediate values of to. The bearing tends to be unstable above a particular to. …

A Closed-Form Solution For The Radiosity At The Edge Of A Rectangular Cavity, Alfred L. Crosbie

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Test 1204: Ford 2600 Diesel 6-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1201: Ford 5600 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1202: Ford 4100 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1209: Case1410 Manual ( David Brown 1410 Synchromesh) Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …

Test 1208: Ford 3600 Gasoline 6-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS Each tractor is a production model equipped for common usage. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operator station. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures must conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crankcase is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The fuel …