Engineering Commons^™

A Potential Problem With The Tsi Electrostatic Aerosol Classifier, Darryl J. Alofs, Max B. Trueblood

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Passive Cooling And Human Comfort, Florida Solar Energy Center, Philip W. Fairey

FSEC Energy Research Center®

Comfort within buildings is primarily controlled by four major factors: air temperature, mean radiant temperature, humidity and airflow. Each can have a dominating effect. Their effects are not necessarily additive and practically never linear. There are, additionally, other factors which affect comfort including clothing, activity level and climatization. Some psychological triggers, such as certain colors, also seem to affect comfort, and "state of mind" can have major effects on individual comfort sensations. Comfort zones, therefore, are very generally defined as the zone in which 80 percent of the population will experience the sensation of thermal comfort.

Economic Comparison Of Flat Rate And Concentrating Solar Collectors For Absorption Air-Conditioning, E. A. Sauer, Harry J. Sauer Jr.

UMR-DNR Conference on Energy

No abstract provided.

Estimation Of Water And Energy Requirements For Ground Water Heat Pumps In The United States, Ronald H. Howell, Harry J. Sauer Jr.

UMR-DNR Conference on Energy

No abstract provided.

Feasibility Study For A Municipal Refuse To Energy Plant, Archie W. Culp Jr.

UMR-DNR Conference on Energy

No abstract provided.

Water Wave Refraction With Non-Linear Theory, Im Sang Oh

OES Theses and Dissertations

Two different kinds of wave refraction models are formulated in the present study using Stokes' third order wave theory. One type of model is utilized in a parametric study employing several different topographies. Wave trajectories obtained from this model, when obtained by using first and third order wave theory with and without the consideration of energy dissipation, show considerable differences. These differences are examined in more detail for a bottom of constant slope: (1) An approximate 10% difference occurs between the refraction coefficients obtained using the first and the third order wave theory. (2) Considerably different ray trajectories are detected …

Analysis Of Aerothermodynamic Environment Of A Titan Aerocapture Vehicle, Hsing Chow

Mechanical & Aerospace Engineering Theses & Dissertations

The extent of convective and rad1ative heating for a Titan entry vehicle is invest1gated. The flow in the shock layer is assumed to be axisymmtric, steady, viscous, and compressible. It is further assumed that the gas is in chemical and local thermodynamic equilibrium and tangent slab approximation is used for the rad1ative transport. The effect of slip boundary conditions on the body surface and at the shock wave are included in the analysis of high altitude entry conditions. The implicit finite difference technique is used to .solve the viscous shock layer equations for a 45-degree sphere cone at zero angle …

Experimental Investigation Of A Rectangular Surface Thermal Plume, Li-Cheng Chu

Mechanical & Aerospace Engineering Theses & Dissertations

An experimental investigation of the three dimensional mean temperature distribution of a rectangular buoyant surface thermal plume has been conducted for a range of buoyancies, velocity ratios, Reynolds numbers, and for various turbulence generating screens in the crossflow. This study has been motivated by a concern about the applicability of laboratory model data for predicting prototype plume behavior.

A large scale model has been built to study a buoyant, rectangular surface thermal plume which enters at right angles to a constant temperature uniform crossflow of depth equal to that of the plume. A large water tank and flume with weir …

Design And Analysis Of A Hybrid Thermoelectric Solar Collector, Kay Eddie Shaheen

Mechanical & Aerospace Engineering Theses & Dissertations

A conventional flat-plate collector is modified by imbedding thermoelectric power generators between the absorber plate and flow tubes in parallel finned-tube passes. As solar energy cascades through these generators a temperature differential between the hot and cold junctions of the device produces direct current electricity. Energy not converted to electric power is converted away for use in domestic space and/or water heating.

A parametric study is performed on the steady-state model via computer program in order to find values of design variables that maximize electric power production for purposes of driving pumps, fans, and ·controlling devices. The results of this …

Experimental Determination Of Post-Buckling Performance Of Steel Angles, Rupasiri Purasinghe

Dissertations and Theses

An experimental testing program was conducted to determine the compression member performance in post-buckling region. These results are compared with an analytical computer program developed by Portland State University under Bonneville Power Administration Contract 79-80BP 24005. The paper presents the sensitivity of the performance of single angle compression members to various parameters such as length to radius of gyration ratio, eccentricity, end conditions and yield stress. The effect of local buckling on long member performance is also documented.

Trailer Hitch, T. Richard Robe

Mechanical Engineering Faculty Patents

The present invention is directed to a trailer hitch for a vehicle. The trailer hitch is designed to be connected to a vehicle and permits two degrees of freedom for the hitchpoint. The first degree of freedom is in a lateral direction which permits the hitchpoint to have freedom to move horizontally in a lateral direction. This degree of freedom is dampened by a viscous dampener to improve the lateral stability of a trailer connected to the hitchball. Further, springs are provided to resist lateral movement and to restore the hitchpoint to its original position during the pulling of a …

Photoelastic Investigation Of Load Transfer In Eccentrically Loaded Single Lap Joints, Stephen Antrim Hann

Mechanical & Aerospace Engineering Theses & Dissertations

Photoelastic models of three eccentrically loaded single lap joints were analyzed. The adherends of each joint were identical and the bondlines differed in thickness and material properties. The adherends were analyzed for both cylindrical plate behavior and geometrical nonlinearity and the load transfer efficiency was examined. For all three models it was found that over 98% of the shank behaves as a cylindrical plate and that a geometrically nonlinear analysis yields bending stresses substantially lower than a linear analysis and that a relatively thick, low modulus bondline can increase load transfer efficiency.

Deposition Of Particles In Vertical Conduits Due To Electrostatic Charge, Diffusion, And Gravity, Melvin Wilbur Gelber

Dissertations

This investigation was made to determine the effect on the deposition of fine particles in a vertical channel and in a vertical tube due to the influences of electrostatic charge, diffusion, and gravity acting in the direction of flow. The flow considered was laminar, incompressible and steady.

The governing equations for the fluid phase were derived from the Navier-Stokes equation and the continuity equation while the equations for the particle phase were derived from Poisson's potential equation and the continuity equation. Since the governing equations are non-linear partial differential equations the solutions were developed using numerical methods.

The flow patterns …

Sound Absorption In N2-H2o Gas Mixtures At Room Temperature And Low Frequency/Pressure Ratios, William Axam Griffin

Mechanical & Aerospace Engineering Theses & Dissertations

This study was motivated by a need to obtain standard values of nitrogen's contribution to sound absorption in the Earth's atmosphere. Specific goals included accurate measurements of sound absorption in nitrogen - water vapor mixtures at room temperature and low frequency/pressure ratios, the determination of the N₂ vibrational relaxation peak location, (f/P)_max, on the f/P axis as a function of humidity, h, and critical evaluation of all results.

The free decay technique was used in a resonance tube to obtain ten sets of sound absorption data in N₂-H₂O gas mixtures and requisite companion …

Effects Of Multiple Scattering And Surface Albedo On The Photochemistry Of The Troposphere, Tommy Reinhold Robert Augustsson

Mechanical & Aerospace Engineering Theses & Dissertations

A one-dimensional photochemical model of the troposphere containing the species of the nitrogen, oxygen, carbon, hydrogen, and sulfur families has been developed and used to investigate the vertical profiles and the natural (including atmospheric chemical reactions) and anthropogenic sources and sinks of these species. The species continuity equations are solved numerically applying prescribed boundary conditions. The vertical flux is simulated by use of the parameterized eddy diffusion coefficients. Heterogeneous losses (e.g. rainout, gas-to-particle chemistry, and dry deposition), are parameterized to make calculated profiles consistent with measurements. The photochemical model is coupled to a radiative transfer model that calculates the radiation …

Deposition Of Suspensions In A Vertical Converging Tube, Kam-Ho Chan

Theses

The deposition of suspensions in a vertical converging tube with significant gravity effects Was investigated theoretically with control volume - finite difference approach. The fluid was assumed to be incompressible and laminar. The particle density was assumed to be uniform at the inlet of the. tube. The velocity profiles for the fluid considered were (a) Uniform profile, (b) Parabolic profile. The angles of convergence studied were 0°, 5° and 7°. Effects of velocity ratio δ^*(=terminal velocity/mean flow velocity) on the rate of deposition were investigated for δ^*=0,1,10.

It was found that deposition increases with increasing angle …

Test 1383: Case 1690 Manual Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1409: Hesston Fiat 1380 Dt Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1399: Massey-Ferguson Mf 2805 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1401: Steiger Couger Iii St-280 Diesel 20-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Ole Miss Engineer 1981

Ole Miss Engineer

No abstract provided.

Novel Demonstration Of Total Internal Reflection, Dwight C. Look

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Test 1382: Case 1490 Powershift Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1389: Massey-Ferguson Mf 2775 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1391: Massey-Ferguson Mf 4900 Diesel 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1387: International 284 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1386: Hesston Fiat 780dt And 780 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1388: International 786 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1393: John Deere 2040 Diesel 8-Speed Tss Transmission, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1404: Deutz Dx-130 Diesel 24-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …