Engineering Commons^™

Nomographs And Tables For Simplified Thermal Analysis Of Power Piping, Dhanjibhai N. Patel

Theses

This Thesis develops Nomographs and Tables for simplified thermal analysis of " Power Piping." It gives the length of required Thermal Relieve Leg when a set of piping parameters such as, pipe size, pipe material, operating temperature and pipe length are given.

The Nomographs and Tables developed here can be used

1. to determine the primary piping layout, piping route, support location etc. before vigorous conputer analysis is performed.

2. to help the Field Engineer on the plant site to make " on the spot " decisions on pending piping route changes.

Two Nomographs are developed in this Thesis. One …

Liquid Transmission Line Pulser Circuit For Laser Excitation, Carl Stultz

Dissertations and Theses

The subject of this thesis is the study of liquid dielectric transmission lines and their potential application as an excitation source in high speed, high-repetition rate laser designs. The design problems associated with the construction of high repetition rate (khz), short wavelength lasers have been reviewed and the major shortcomings of conventional electrical driving circuits identified. The identification of these shortcomings and a review of the available literature on electrical circuits for various types of lasers suggested that liquid dielectrics and transmission lines could potentially have significant advantages over more conventional circuitry used in high repetition rate, short wavelength lasers. …

A Heat Pump Assisted Shower, Jim Mcgovern

Articles

An energy-efficient water-heating system for a shower is proposed consisting of a low-powered heat pump, a storage tank and an instantaneous heater which, it is felt, may yield a favourable overall cost, in addition to reducing the primary energy consumption. Some preliminary work has been carried out in exploring this concept. It was considered at the outset that an overall coefficient of performance (COP) of 2 should be readily achieved. Values close to this have been realised with the first experimental prototype.

Motivation And The First Line Supervisor: A Survey Of Techniques And Applications, Raymond H. Rannfeldt

Graduate Research Papers

Do first line supervisors differ in their beliefs concerning motivation or in the techniques they employ to motivate their personnel as a function of age, time in service with a company and/or time as a supervisor?

Application Of The Method Of Lines For Solutions Of The Navier-Stokes Equations Using A Nonuniform Grid Distribution, Jamshid Samareh Abolhassani

Mechanical & Aerospace Engineering Theses & Dissertations

The feasibility of the method of lines is investigated for solutions of physical problems requiring nonuniform grid distributions. To attain this, it was also necessary to investigate the stiffness characteristics of the pertinent equations. For specific applications, the governing equations considered are those for viscous, incompressible, two-dimensional and axisymmetric flows. These equations are transform­ ed from the physical domain having a variable mesh to a computational domain with a uniform mesh. The two governing partial differential equations are the vorticity and stream function equations. The method of lines is used to solve the vorticity equation and the successive over relaxation …

Effect Of Transducer Size On The Statistical Properties Of A Simulated Turbulent Wall Pressure Field, Mehdi R. Khorrami

Mechanical & Aerospace Engineering Theses & Dissertations

The root mean square pressure was calculated with synthetically generated pressure signals for transducers of different size. The transducer diameters were in the range of 0.02 < _s*of 12,250. The lower limit of the diameter simulated here was much smaller than diameters reported previously by other workers. Calculated root mean square pressure levels developed in the present work were in good agreement with the measured experimental data.

In order to check the simulated pressure signals, the power spectrum and two point correlation were calculated as well. The power spectra obtained with the smaller transducers were higher in energy level at …

Viscous Modeling And Computation Of Leading-And Trailing-Edge Vortex Cores Of Delta Wings, Balakrishnan Lakshmanan

Mechanical & Aerospace Engineering Theses & Dissertations

A Finite-Difference method is presented for calculating steady quasi-axisymmetric flow of an incompressible fluid at large Reynolds number. Approximations of the boundary-layer type are employed to reduce the Navier-Stokes equations to a pair of non-linear parabolic equations. Along with the governing equations, initial conditions are specified at some upstream cross section and boundary conditions are specified at the axis of symmetry and on the outer bounding surface.

The governing equations are replaced by a set of quasilinear finite-difference equations. The solution is obtained by a marching technique, which proceeds step-by-step in the axial direction. At each axial station, an iterative …

On The Space Shuttle Wing Thermal-Structural Analysis, Kumar Krishna Tamma

Mechanical & Aerospace Engineering Theses & Dissertations

A finite element approach for efficient thermal-structural analysis of structures with thermal protection systems (TPS) is described. The approach is applied to Space Shuttle wing structure configurations subjected to reentry heating. New two and three-dimensional finite elements are developed to model heat transfer in the TPS and supporting structure. A typical TPS/Structural element predicts transient nonlinear temperature variations through the TPS thickness and detailed structural temperatures at the TPS/Structure interface. The accuracy of the TPS/Structure approach in two and three-dimensions is evaluated by comparisons with the conventional approach for various configurations of the wing structure. The results indicate that the …

On The Analysis And Design Of Clamped Rectangular Plate With Partial Load, Yacin Saaid Jaboury

Theses

In this Thesis, maximum deflection and bending moments of a partially loaded clamped rectangular plate are studied. The loading is uniformly applied to a retangular area proportional to the shape.

Navier's Solutions on partially loaded simply supported rectangular plate is superimposed with edge moments to give the clamped boundry condition.

Solutions of maximum deflection and bending moments are derived in Double Series form. A Fortran program is employed in obtaining the numerical results. When the partially loaded area approaches zero it becomes a centrally loaded case; and when loading area to plate area ratio approaches unity it becomes a uniformly …

Numerical Solution Of Navier-Stokes Equation By Finite Element Method, Kuan-Tzong Lee

Theses

A finite element method for solving the entrance flow in a parallel-plate channal at low Reynolds number has been studied. Two methods of formulation for both incompressible viscous and inviscid fluid flows were developed. The first uses stream function and potential function as field variables while the second uses velocity and pressure. Both formulations presented here ultilized variational principle and weighted residual method. The numerical example was solved by constrained variational principle with penalty functions in conjunction with the Newton-Raphson method. A 9-node quadratic quadrilateral element was used in this example. Numerical results for entrance flow problem were obtained for …

Bevolute Gear System, Willis M. Carter

Mechanical Engineering Faculty Patents

The present invention relates to a bevolute gearing system which transmits torque between non-intersecting shafts at right angles to each other. The bevolute gear system includes a pinion gear which is flat and in one plane. The pinion gear is designed to include teeth which are shaped in the form of an involute spiral. The bevolute gear system includes a second gear which is also designed to include teeth which are shaped in the form of an involute spiral. The second gear is mounted on a non-intersecting axis at a right angle to the axis of the pinion gear. The …

On The Thermodynamics Of Solar Energy Use, Edward A. Fletcher

Journal of the Minnesota Academy of Science

Solar energy, coming from a 5800K heat reservoir, has thermodynamic advantages over fossil fuel combustion which are rarely recognized. This essay discusses the pertinent thermodynamics of chemical conversion processes. It points out the advantage of conducting endothermic processing at high temperatures and the unique character of sunlight as a source of process heat for high-temperature processing.

Test 1475: John Deere 4250 Quadrange Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1494: Ford 3910 (8x4) Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1468: White Farm Equipment 2-110 Diesel 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

An Improved Rotary Singulator, Burford J. Furman, J. M. Henderson

Faculty Publications, Mechanical Engineering

A new operating approach for a previously existing rotary singulator was developed which improves the versatility of the device. This was accomplished by the implementation of a modular mechanism that performed the basic functions of agitation, gating, pocket formation, and exit, all inherent in this type of singulation device.

Test 1502: Ford 1710 (12x4) Manual Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Saving Energy In Rural Maine : Or Who's Doing What On The Farm, Mane Department Of Agriculture

Maine Collection

Saving Energy In Rural Maine : Or Who's Doing What on the Farm

Compiled by Bettina M. Blanchard and Edited by Bill Seekins.

Maine Department of Agriculture, Food and Rural Resources, Division of Resources Development, Augusta, Maine, 1983.

Contents: List of Photographs and Diagrams / Introduction / Projects / 1. Wind / 2. Wood Heat Applications On the Farm / 3. Solar Applications / 4. Manure Handling and Waste Utilization / 5. Energy Efficient Cooling Methods / 6. Energy Saving In Field Operations / 7. Production and Use of Alternative Fuels / 8. Multi-Project Sites / Summary and Conclusions / …

Test 1470: John Deere 2350 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1467: White Farm Equipment-Iseki 2-65 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1469: John Deere 2150 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1472: John Deere 2750 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1473: John Deere 2950 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1474: John Deere 4050 Quadrange Diesl 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1478: Massey-Ferguson 254 Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1481: Massey-Ferguson 2640 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1492: Ford 2910 (8x4) Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1483: Versatile 875 Series 3 Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1479: Massey-Ferguson 274 Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1486: White Farm Equipment-Iseki 2-75 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …