Engineering Commons^™

Low Speed Flowfield Characterization By Infrared Measurements Of Surface Temperatures, Ehud Gartenberg

Mechanical & Aerospace Engineering Theses & Dissertations

An experimental program was aimed at identifying areas in low speed aerodynamic research where infrared imaging systems can make significant contributions. Implementing a new technique, a long electrically heated wire was placed across a laminar jet. By measuring the temperature distribution along the wire with the IR imaging camera, the flow behavior was identified. Furthermore, using Nusselt number correlations, the velocity distribution could be deduced. The same approach was used to survey wakes behind cylinders in a wind-tunnel. This method is suited to investigate flows with position dependent velocities, e.g., boundary layers, confined flows, jets, wakes and shear layers. It …

Experimental Study Of Pressure And Heating Rate On A Swept Cylindrical Leading Edge Resulting From Swept Shock Wave Interference, Christopher E. Glass

Mechanical & Aerospace Engineering Theses & Dissertations

An experimental study of the effects of leading edge sweep on surface pressure and heat transfer rate for swept shock wave interference is presented. This study was conducted as a cooperative agreement between NASA Langley Research Center and Calspan-University of Buffalo Research Center. Experimental tests were conducted in the Calspan 48-inch Hypersonic Shock Tunnel at a nominal Mach number of 8, nominal unit Reynolds number of 1.5 x 10⁶ per foot, leading edge and incident shock generator sweep angles of 0^o, 15^o, and 30^o, and incident shock generator angle-of-attack fixed at 12.5^{o …}

The Effects Of Nonlinearities On The Optimal Design Of Forced Vibrating Beams, Cheryl Celestine Jackson

Mechanical & Aerospace Engineering Theses & Dissertations

The optimal design of a beam under harmonic excitations is formulated and solved numerically for linear and nonlinear forced vibration theories. The beam has a nonuniform cross-sect ion, whose thickness can change during the optimization procedure. Based on the numerical results, for the given input frequency range, the linear vibration theory produces a more conservative design than the nonlinear vibration theory.

The analytical formulation for both theories is presented. For the linear case, a mean case is defined for the self-weight on a beam, and an alternating case is defined for input forcing frequencies which cause fatigue variations on a …

Transient Hot-Film Sensor Response In A Shock Tube, Kelly Ryan Ortgies

Mechanical & Aerospace Engineering Theses & Dissertations

Shock tube experiments have been performed to determine the response of a hot-film sensor, mounted flush on the side-wall of a shock tube, to unsteady flow behind a normal shock wave. The present experiments attempt to isolate the response of the anemometer due only to the change in convective heat transfer at the hot-film surface. The experiments, performed at low supersonic shock speeds in air, are described along with the data acquisition procedure. The change in convective heat transfer i s deduced from the data and the results are compared with those from transient boundary-layer theory and another set of …

An Adaptive Remeshing Finite Element Method For High-Speed Compressible Flows Using Quadrilateral And Triangular Elements, Gururaja R. Vemaganti

Mechanical & Aerospace Engineering Theses & Dissertations

In this study a new adaptive remeshing method for high speed compressible flow analysis is presented. The method uses quadrilateral elements where possible, and triangles are introduced as needed. The primary goal of this study is to develop a remeshing method which uses both the concepts of unstructured and structured meshes for the finite element analysis to predict accurate aerodynamic heating in problems related to high speed viscous flows. The remeshing method uses a solution based on an old mesh to create a new mesh based on an advancing front technique. In the present implementation, a structured mesh of quadrilaterals …

Design Of A Multiple Degree Of Freedom, Force Reflective Hand Master/Slave With A High Mobility Wrist, Tim Mclain, S C. Jacobsen, E K. Iversen, C C. Davis, D M. Potter

Faculty Publications

The Center for Engineering Design (CED) at the University of Utah has developed a force reflective, teleoperated multiple degree of freedom hand and high mobility wrist. This hand/wrist teleoperation system is targeted to perform dexterous manipulation and assembly tasks in an effort to approach the capabilities of a human. A first-stage prototype of this hand/wrist master/slave system, which is scheduled for laboratory demonstration in February of 1989, has nine actuated degrees of freedom in both the hand master and hand slave. This paper discusses elements of the design of this hand/wrist master and slave with particular emphasis on servo system …

Thermal Performance Monitoring Results From The Residential Standards Demonstration Program, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

The Model Conservation Standards (MCS) were developed by the Northwest Power Planning Council in 1983. These standards were designed to save large amounts of space heating energy in new U.S. residential construction in the Pacific Northwest. Creation of the MCS resulted in a desire to demonstrate the actual savings of such energy efficiency standards. The Bonneville Power Administration sponsored the Residential Standards Demonstration Program (RSDP) in 1984 which resulted in the construction of 410 energy-efficient single-family homes in the four-state region. Typically these buildings incorporated design features such as high levels of insulation for attic, walls and floors, triple-glazed windows …

Ionitriding To Improve The Wear Resistance Of Ferrous Materials, Ravi K. Kodali

Theses

In this work the effect of ionitriding treatment on wear resistance of ferrous materials was studied. A basic understanding of the ionitriding concepts were given and the advantages of this process over other conventional nitriding treatments were outlined. The effect of various parameters like gas composition, temperature, pressure, process duration and power density on the metallurgical aspects of this process were discussed. Under technical aspects of this technology, advantages of pulsed direct current over conventional direct current nitriding systems were given. In this work wear tests were performed on components made from gray cast iron, alloy steel (AISI 4340), and …

The Greenhouse Effect, Florida Solar Energy Center, Ingrid Melody

FSEC Energy Research Center®

Use of conventional energy sources - in Florida and throughout the world - has produced a global problem known as "the greenhouse effect." While the scientific community does not always agree on the greenhouse effect's potential impacts on the planet, and while policy makers do not always agree on methods to ameliorate or adapt to it, most concur on at least a few points: The greenhouse effect does indeed exist and is primarily a result of our use of carbon-based energy supplies. The greenhouse effect is changing the planet's climate. The greenhouse effect presents circumstances unique in human history - …

The Development Of An Efficient Lupin Harvesting Front, E D. Blanchard

Journal of the Department of Agriculture, Western Australia, Series 4

Harvest losses represent a significant reduction in lupin production and farm productivity.

Since 1984, the Department's Farm Machinery Research and Liaison Unit at the Dryland Research Institute has studied the lupin harvesting operation to improve its mechanical efficiency. An experimental and a prototype harvesting front were built and tested in the field. Guidlines for efficient lupin harvesting were produced, and commercial modifications developed.

Integrating Scheduling And Control Functions In Computer Integrated Manufacturing Using Artificial Intelligence, Luis Carlos Rabelo, Sema E. Alptekin

Industrial and Manufacturing Engineering

Proper integration of scheduling and control in Flexible Manufacturing Systems will make available the required level of decision-making capacity to provide a flexibly-automated, efficient, and quality manufacturing process. To achieve this level of integration, the developments in computer technology and sophisticated techniques of artificial intelligence (AI) should be applied to such FMS functions as scheduling. In this paper, we present an Intelligent Scheduling System for FMS under development that makes use of the integration of two AI technologies. These two AI technologies — Neural Networks and Expert Systems — provide the intelligence that the scheduling function requires in order to …

Ole Miss Engineer 1989

Ole Miss Engineer

No abstract provided.

Feasibility Study Of Maine's Small Hydropower Potential, James D. Sysko

Maine Collection

Feasibility Study of Maine's Small Hydropower Potential

Prepared by James D. Sysko, Small Hydro East, for the Maine State Planning Office, Maine Office of Energy Resources, January 1989.

"This study focuses on finding potential hydropower sites of approximately 50 kw to 1000 kw in capacity."

Viscous Cross-Waves: An Analytical Treatment, Andrew J. Bernoff, L. P. Kwok, Seth Lichter

All HMC Faculty Publications and Research

Viscous effects on the excitation of cross‐waves in a semi‐infinite box of finite depth and width are considered. A formalism using matched asymptotic expansions and an improved method of computing the solvability condition is used to derive the relative contributions of the free‐surface, sidewall, bottom, and wavemaker viscous boundary layers. This analysis yields an expression for the damping coefficient previously incorporated on heuristic grounds. In addition, three new contributions are found: a viscous detuning of the resonant frequency, a slow spatial variation in the coupling to the progressive wave, and a viscous correction to the wavemaker boundary condition. The wavemaker …

Improved Fertilizing Practices On The Peel-Harvey Catchment, P T. Arkell

Journal of the Department of Agriculture, Western Australia, Series 4

Broad-acre farmers in the Peel-Harvey catchment have met a challange and achieved a great deal since the fertilizer extension programme started in 1983.

The main objective of the extension programme has been to ensure that every year three-quarters of the farmers make economically and technically sound fertilizer decisions, thus causing a minimum amount of phosphorus to enter the waterways of the Peel-Harvey estuarine system.

Nonlinear Tracking Control Of Brushless Dc Motors For High-Performance Applications, N. Hemati, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The tracking control problem associated with brushless DC motors (BLDCMs) for high-performance applications is considered. To guarantee their high-dynamic-performance operation in motion control systems, the magnetic saturation and reluctance variation effects are accounted for in the BLDCM mathematical model. The trajectory tracking control problem is addressed in the context of the transformation theory of nonlinear systems. A nonlinear control law is implemented and shown to compensate for the nonlinearities of a BLDCM. A case study is presented in which a direct-drive inverted pendulum actuated by a BLDCM is used to investigate the effectiveness of the control law. The effectiveness of …

Generic Singularities Of Robot Manipulators, Ming-Chuan Leu, D. K. Pai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The singularities of the differential kinematic map, i.e. of the manipulator Jacobian, are considered. The authors first examine the notion of a generic kinematic map, whose singularities form smooth manifolds of prescribed dimension in the joint space of the manipulator. For three-joint robots, an equivalent condition for genericity using determinants is derived. The condition lends itself to symbolic computation and is sufficient for the study of decoupled manipulators, i.e. manipulators that an be separated into a three-joint translating part and a three-joint orienting part. The results are illustrated by analyzing the singularities of two classes of three-joint positioning robots.

Nebraska Summary: S078 Ford Versatile 276, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S079 Massey Ferguson 390t, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S071 Massey Ferguson 253, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Optimal Design Rules Applied To The Design Of High-Speed Mechanisms Under Deflection And Stress Constraints, Frank W. Liou, Jenny Liu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Presented in this paper are two approaches for the design of flexible mechanisms under stress and deflection constraints. Based on the optimality conditions derived in this paper, two procedures are developed to design the minimum weight of mechanisms subject to stress and deflection limitations. The first procedure is the improvement of Thornton's design process r 17), and the second procedure is based on the interpolation technique. Several design examples are also presented to demonstrate these methods.

Axisymmetric Vibrations Of Reinforced Orthotropic Shallow Spherical Caps, Victor Birman, George J. Simitses

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Axisymmetric vibrations of reinforced shallow, spherical caps manufactured from orthotropic materials are considered. The closed form solution is obtained for the natural frequency of the cap with a clamped and immovable circular edge by assuming that the motion component parallel to the cap boundary plane (in plane) is negligible. Parametric studies are performed to assess the effect of various geometric and structural parameters on the natural frequency of the cap and, most importantly, to identify the most influencing parameters of the problem. From the generated data, it is concluded that the national frequency increases with increasing extensional stiffness and eccentricity …

Test 1627: John Deere 4255 Quadrange Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1631: John Deere 8760 Powershift Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1632: John Deere 8960 Powershift Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1634: Deutz-Allis 9170 Diesel 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Nebraska Summary: S075 Case-Ih 5120, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S074 Case-Ih 1896, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S072 Massey Ferguson 3680, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1633: Deutz-Allis 9150 Diesel 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …