Engineering Commons^™

Nebraska Summary: S421 Mccormick Mtx 110, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1798: John Deere 8320 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Test 1809: John Deere 6603 Diesel 9-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Test 1800: John Deere 8420 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 385: John Deere 6220 Powrquad Plus Diesel 24-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 387: John Deere 6420 Autoquad Diesel 24-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 410: Fendt 410 Vario, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

A New Filtering Technique For A Class Of Nonlinear Systems, Ming Xin, S. N. Balakrishnan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In this paper, a new nonlinear filtering technique (θ-D filter) is presented. This filter is derived by constructing the dual of a new nonlinear regulator control technique, θ-D approximation which involves approximate solution to the Hamilton-Jacobi-Bellman equation. The structure of this filter is similar to the state dependent riccati equation filter (SDREF). However, this method does not need time-consuming online computation of the algebraic Riccati equation at each sample time compared with the SDREF. By manipulating the perturbation terms both the asymptotic stability and optimality properties can be obtained. A simple pendulum problem is investigated to demonstrate the effectiveness of …

State-Constrained Agile Missile Control With Adaptive-Critic-Based Neural Networks, Dongchen Han, S. N. Balakrishnan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In this study, we develop an adaptive-critic-based controller to steer an agile missile that has a constraint on the minimum flight Mach number from various initial Mach numbers to a given final Mach number in minimum time while completely reversing its flightpath angle. This class of bounded state space, free final time problems is very difficult to solve due to discontinuities in costates at the constraint boundaries. We use a two-neural-network structure called "adaptive critic" in this study to carry out the optimization process. This structure obtains an optimal controller through solving optimal control-related equations resulting from a Hamiltonian formulation. …

Nebraska Summary: S407 Case-Ih Jx80u, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Comparison Of Mobility Method And Mass Conservation Method In A Study Of Dynamically Loaded Journal Bearings, Biao Yu, Jerzy T. Sawicki

Mechanical Engineering Faculty Publications

The inverse problem of dynamically loaded journal bearings was solved using generalized Reynolds equation coupled with a complete mass conservative cavitation boundary conditions, as outlined by the Jacobsson-Floberg and Olsson (JFO) cavitation theory. In the course of solution, the modified Thomas algorithms was employed, instead of standard Gauss±Jordan reduction method, which fully utilizes the sparse character of the system matrix, and thus greatly reduces computational time. The developed model was tested against the well-known mobility method for the case of journal bearings in a commercial reciprocating air compressor. It was found that the mobility method overestimates minimum film thickness and …

Development And Application Of Streakline Visualization In Hypervelocity Flows, P. Lemieux, H. G. Hornung

Mechanical Engineering

A method for visualizing streaklines in hypervelocity flows has been developed. The method uses the high temperatures produced in hypervelocity flows to ablate small amounts of sodium deposited onto a wire stretched across the flow and to broaden the lines in the sodium spectrum. By using a dye laser, tuned to a wavelength close to one of the sodium D-lines, as the light source in shadowgraph or Schlieren visualization, streaklines seeded with sodium become visible through absorption and/or enhanced refractivity. The technique has been used to investigate the stability of the shear layer produced by the curved bow shock on …

A Venture Capital Fund For Undergraduate Engineering Students At Rowan University, Anthony J. Marchese, John C. Chen, John L. Schmalzel

Mechanical Engineering

All engineering students at Rowan University are required to take the 8-semester Engineering Clinic sequence wherein multidisciplinary student teams engage in semester-long design projects. In addition to projects that are funded by local industry, faculty research grants or departmental budgets, a Venture Capital Fund has been created, which is specifically ear-marked for the development of original student inventions. Funding of up to $2500 per student team per semester is competitively awarded based on student-generated proposals to the Venture Capital Fund, which has been created through a series of grants from the National Collegiate Inventors and Innovators Alliance (NCIIA). To qualify …

Tests 2031 & 2055: Case Ih Jx 85 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Prediction Of Heat Transfer & Flow In Rotating Two-Pass Channels Connected By Holes., Achintya Kumar Pramanick

LSU Master's Theses

A computational study of the effect of rotation on the velocity and thermal field for a two-pass channel connected by rows of holes on the divider wall has been conducted. Detailed velocity and Nusselt number distributions are presented inside the rotating two-pass coolant channel. The enhanced cooling in this passage design is achieved by a combination of impingement and crossflow-induced swirl. The cross flow is generated from one coolant passage to the adjoining coolant passage through a series holes placed along the dividing wall. The holes deliver the flow from one passage to another typically achieved in a conventional design …

Buckling Analysis Of Grid Stiffened Composite Structures, Samuel Kidane

LSU Master's Theses

Buckling of a stiffened composite cylinder is a very complex phenomenon that involves complex interactions between the skin and the stiffeners. Depending on different configurations of the skin and stiffener, different buckling failure modes and failure loads are observed in stiffened cylinders. In this work failure modes and buckling loads of stiffened composite cylinders under uniaxial loading condition is investigated by using analytical and experimental approaches. In the first Chapter an improved smeared method is developed to model the buckling problem of an isogird stiffened composite cylinder. In this model the stiffness contributions of the stiffeners is computed by analyzing …

Flow Patterns In A Two-Roll Mill, Christopher Hills

Articles

The two-dimensional flow of a Newtonian fluid in a rectangular box that contains two disjoint, independently-rotating, circular boundaries is studied. The flow field for this two-roll mill is determined numerically using a finite-difference scheme over a Cartesian grid with variable horizontal and vertical spacing to accommodate satisfactorily the circular boundaries. To make the streamfunction numerically determinate we insist that the pressure field is everywhere single-valued. The physical character, streamline topology and transitions of the flow are discussed for a range of geometries, rotation rates and Reynolds numbers in the underlying seven-parameter space. An account of a preliminary experimental study of …

Hard Surface Coating Experimental Evaluation And Thermomechanical Analysis Of A Seal With Micro Heat Exchanger, Yifan Qiu

LSU Master's Theses

Mechanical face seals are important components of many rotating machinery. Minimizing the friction between seal faces and efficiently removing the heat generated between seal surfaces are two crucial considerations in the design of mechanical seal. Thin film coating and MEMS technology hold great promise for improving the performance of mechanical seals from the viewpoint of reducing friction and heat at the interface in these two aspects. To reveal what effect the coating and MEMS technology can have on tribological properties of seals, friction and wear characteristics of Ti-C:H coatings on seal-like rings and heat transfer performances of a seal prototype …

Parametric And Sensitivity Analysis Of A Vibratory Automobile Model, Kanika Nicole Vessel

LSU Master's Theses

Vibration response is an important aspect of any engineering problem. This thesis deals with developing a method to obtain the vibration, parametric and sensitivity of an automobile analyzed as a 2-DOF rigid body system with damping. The focus of the vibration analysis is to obtain the poles, eigenvectors, and natural frequencies of the system. The parametric analysis gave information on how the natural frequency is affected when one of the parameters is perturbed. Information about how much the system is affected by the change in one parameter is what is obtained from the sensitivity analysis. The theoretical solution contained in …

A Model Of Heat And Mass Transfer In An Idealized Micro Heat Pipe, Jin Zhang

LSU Master's Theses

Micro heat pipes have been used to cool computer chips, but their heat transfer coefficients are low compared with that of conventional heat pipes. To understand this deficiency, an idealized micro heat pipe is proposed that has simplified interfacial geometry but retains the essential physics. It is a long and narrow cavity of rectangular cross section with the bottom made of a wetting material and the top a non-wetting material. A wetting liquid fills the bottom half of the cavity, and its vapor fills the rest. This configuration ensures that the liquid-vapor interface is pinned at the contact line. Since …

Application Of Duhamel's Theorem To Problems Involving Oscillating Heat Source, Haribabu Krishnamurthy

LSU Master's Theses

This thesis deals with a systematic development of a method for predicting the temperature field in various domains subjected to oscillating heat sources on its boundaries using the Duhamel’s method. First a method is devised for single domain problems in both Cartesian and cylindrical coordinates for oscillating heat sources and also for unidirectional rotation of shafts in cylindrical coordinates. The analytically computed results for the problems in Cartesian coordinates compared favorably with the results from Finite Element Method, attesting to the validity of this novel approach. Later, the method is extended to predict the maximum temperature in oscillating Pin-Bushing mechanism, …

Liga Mold Insert Fabrication Using Su-8 Photoresist, Jian Zhang

LSU Master's Theses

The LIGA process potentially enables economic mass-production of devices with high aspect ratio geometry. Central to the LIGA process is the fabrication of high quality LIGA molds. But in the traditional LIGA mold insert fabrication process, the x-ray photoresist poly-methyl-methacrylate (PMMA) is not highly sensitive to x-rays and a thick piece of PMMA sheet (>1mm) needs too much time to get exposed (bottom dose: 3500J/cm3), which results in excessive cost/ fabrication difficulty of the mold insert. Thus, in this thesis a negative photoresist SU-8 was tested as an x-ray photoresist in the LIGA fabrication process. SU-8 is much more …

Design And Microfabrication Of A Molded Polycarbonate Continuous Flow Polymerase Chain Reaction Device, Michael Mitchell

LSU Master's Theses

The polymerase chain reaction (PCR) is an amplification technique that is used with deoxyribonucleic acid (DNA) and can produce millions of copies of the starting material, even from single molecules. Since its discovery by Kary Mullis in the mid-1980s, PCR has been one of the most important techniques in the arsenal of tools used for genetic analyses. For this research a continuous flow polymerase chain reaction (CFPCR) system was designed, microfabricated from molded polycarbonate, and tested. Finite element modeling was used to model thermal and microfluidic response of the system. X-ray LIGA was used to fabricate mold inserts for the …

Development Of A Micro Power Relay With Static Electrical Actuator, Ren Yang

LSU Master's Theses

In this thesis, a research about design and fabrication of a micro power relay is presented. Compared with the traditional electromagnetic relay and solid-state relay, MEMS micro power relay is introduced. After introducing the advantage and other people's research about the MEMS relay, some design and simulation about a new prototype micro power relay are done. Based on the design, UV-LIGA is used as the fabrication method. The bottom part and top part of the micro power relay are fabricated separately. After assembly the top part on the bottom part, some simple tests about the micro power relay are done. …

Transient Thermomechanical Interactions Of Shaft-Bushing Pair In Bearings - A Finite Element Study, Rajesh Krithivasan

LSU Master's Theses

This thesis presents a finite element parametric study of the transient thermomechanical interactions of shaft-bushing pairs in bearings to gain insight into the nature of two categories of failures encountered in practice. The first type of failure deals with occurrence of the so-called thermally induced seizure (TIS) during the start-up period followed by an investigation of TIS due to a transient flow-disturbance. The second part deals with the thermomechanical interactions of pin-bushing assembly under heavy oscillating loads where the failure is by TIS and/or thermal galling. An extensive set of parametric simulations covering a wide range of loads, speeds, operating …

Tribological Behavior Of Nanostructured Nickel, Dean Joseph Guidry

LSU Master's Theses

The present study reports the effects of electroplating parameters on the microstructure, and thus the mechanical and tribological properties, of nanostructured nickel. Electroplating was conducted in a Watt's type bath with a pH of 3.0 carried out using direct current in galvanostatic mode at current densities of 30 mA/cm² and 15 mA/cm² in electroplating bath temperatures of 30°C and 50°C. Grain size and distributions were determined from TEM (Transmission Electron Microscope) and SEM (Scanning Electron Microscope) micrographs. Tribological tests were carried out on a pin-on-disc type tribometer. The same tests were conducted on Ni-200 for the purpose of …

Comparison Of Numerical And Experimental Results Of Four Liquid Spray Combustors, Dong Hu

LSU Master's Theses

Validation of CFD predictions for liquid spray combustion application is a challenging task due to difficulties in both modeling and experimental measurements. Validation is considered to be a key step for successful CFD predictions of combustion systems. The goals of this thesis are threefold: (1) validation of models used for spray combustion predictions, (2) using the validated predictions to explain steady flow and combustion physics, and (3) using the validated procedure to simulate conditions where unstable combustion behavior is observed experimentally, and to explore if such unstable behavior can be predicted correctly. The model validation is done with respect to …

Effect Of Tip Geometry On Blade Tip Flow And Heat Transfer, David Michael Kontrovitz

LSU Master's Theses

In an attempt to increase thrust to weight ratio and efficiency of modern gas turbines, engine designers are always interested in increasing turbine operating temperatures. The benefits are attributed to the fact that higher temperature gases yield a higher energy potential. However, the detrimental effects on the components along the hot gas path can offset the benefits of increasing the operating temperature. The High Pressure Turbine (HPT) first stage blade is one component that is extremely vulnerable to the hot gas. The present study explores the effects of gap height and tip geometry on heat transfer distribution. This investigation differs …

Tapered Liga Mold Insert, Ryan Anthony Turner

LSU Master's Theses

The applications of microstructures produced by the LIGA process are useful in a broad range of fields including: microfluidics, heat transfer, and mechanics. The Microsystems Engineering Team at Louisiana State University has used the LIGA process as a foundation for the team’s productivity in these areas. Many advances in the processes involved in producing these microstructures have been made in the past increasing the efficiency of the entire process. A modified exposure technique in the lithography stage of the LIGA process is being developed to produce microstructures with a draft angle as opposed to the standard straight walled structures. Electroformed …

Spectral Integration Of Microstructure And Design, Brent L. Adams, B. Henrie, M. Lyon, H. Garmestani, Surya R. Kalidindi

Faculty Publications

Support of the Army Research Office is greatly appreciated. Mechanical design can be conducted in a framework where consideration of microstructure as a continuous design variable is facilitated by the use of a Fourier space. Selection of the mechanical framework for the problem (e.g., mechanical constitutive model and homogenization relations) dictates the dimensionality of the pertinent microstructure representation. Microstructure is comprised of basic elements that belong to the local state space. Local state includes crystallographic phase and orientation, and other parameters such as composition. The local state space is transformed into an isomorphic set in Fourier space. The universe of …