Engineering Commons^™

Nebraska Summary 476: Agco Rt 100 Powrmaxx Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Stationkeeping Of An L₂ Libration Point Satellite With Θ-D Technique, Ming Xin, S. N. Balakrishnan, Henry J. Pernicka, Michael W. Dancer

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A new method for L₂ libration-point orbit stationkeeping is proposed in this paper using continuous thrust. The circular restricted three-body problem with Sun and Earth as the two primaries is considered. The unstable orbit about the L₂ libration-point requires stationkeeping maneuvers to maintain the nominal path. In this study, an approach, called the "θ-D technique," based on optimal control theory gives a closed-form suboptimal feedback solution to solve this nonlinear control problem. In this approach the Hamiltonian-Jacobi-Bellman (HJB) equation is solved approximately by adding some perturbations to the cost function. The controller is designed such that the actual …

Modeling, Fabrication, And Optimization Of Niobium Cavities, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

One of the key technologies for the deployment of acceleratordriven transmutation systems is the accelerator itself. Elliptical superconducting niobium cavities are used to increase the efficiency of the high-power accelerators needed to support the transmutation mission.

One of the major sources of energy loss from a superconducting accelerator cavity is a process known as multiple impacting (or “multipacting”) of electrons. This phenomenon limits the maximum amount of energy and power that the niobium cavity can store. As a result, the maximum power available for accelerating the desired charge, as well as the overall performance of the accelerator is reduced. Furthermore, …

Fantasy And The Concert Hall: Musical Performance In The Electroacoustic Age, Matthew Malsky

Reconstruction: Studies in Contemporary Culture

[First paragraph]

In 1941, the famously despondent Theodor Adorno worried about the detrimental effects of radio broadcast upon the symphony. He theorized that much of value was lost when listeners experienced an orchestral performance of a composition in symphonic form through its electronic transmission to their kitchens rather than in a concert hall. Based upon empirical research done in collaboration with Paul Lazarsfeld and the Princeton Radio Research Project, he argued that the presence of music was lost to the radio listener, and with it a part of music's auratic spell, its uniqueness in time and place, its ritual, cultish …

A Nonlinear Model For Prediction Of Dynamic Coefficients In A Hydrodynamic Journal Bearing, Jerzy T. Sawicki, T.V.V.L. N. Rao

Mechanical Engineering Faculty Publications

This paper investigates the variation of nonlinear stiffness and damping coefficients in a journal orbit with respect to equilibrium position. The journal orbit is obtained by the combined solution of equations of motion and Reynolds equation. In the linearized dynamic analysis, dynamic pressure is written as a perturbation of static pressure and pressure gradients at equilibrium position. However, in order to obtain nonlinear dynamic coefficients about equilibrium position, the dynamic pressure gradients in the orbit are also written as the first order perturbation of static pressure gradients and higher order pressure gradients for displacement and velocity perturbations. The dynamic coefficients …

Magneto-Acoustic Emission Analysis Of Microstructural Change In Aisi 430 And Aisi 304 Stainless Steel, Denis O'Sullivan

Theses

Magneto-acoustic emission (MAE) is a relatively new non-destructive detection technique. Its working principle is based on Barkhausen discontinuities and magnetostriction within a ferromagnetic material that is subjected to a varying magnetic field. Magneto-acoustic emission (MAE) and magnetic Barkhausen noise (MBN) sensing techniques were developed and employed to characterise plastically deformed and heat-treated AISI 430 ferritic stainless steel and AISI 304 austenitic stainless steel samples. A new waveform measurement parameter for magneto-acoustic emission was developed called MAE (Absolute “energy”).

Both MAE and MBN were found to decrease with increasing plastic deformation of AISI 430. MAE (Absolute “energy”) and MBN (RMS) were …

Digital Imaging Experiences For Undergraduate Engineering Students, Kauser Jahan, John Chen, Shreekanth Mandayam, Robert Krchnavek, Beena Sukumaran, Yusuf Mehta, Jennifer Kadlowec, Paris Von Lockette, Robi Polikar

Mechanical Engineering

Our project is an effort by a multidisciplinary team of engineering faculty members at Rowan University to integrate digital imaging technology (DIT) into the undergraduate engineering curriculum. It builds upon the experience and interest of faculty to promote new topics and innovative methods of teaching. The work is an effort to provide students with the skills directly relevant to the evolving needs of the industry and the marketplace. Projects involve the development of digital imaging curriculum and focus on the creation of a leading edge digital imaging laboratory/studio to facilitate the use of nontraditional learning approaches that encourage interactive learning, …

Inverse Boundary Element/Genetic Algorithm Method For Reconstruction O, Mahmood Silieti

Electronic Theses and Dissertations

A methodology is formulated for the solution of the inverse problem concerned with the reconstruction of multi-dimensional heat fluxes for film cooling applications. The motivation for this study is the characterization of complex thermal conditions in industrial applications such as those encountered in film cooled turbomachinery components. The heat conduction problem in the metal endwall/shroud is solved using the boundary element method (bem), and the inverse problem is solved using a genetic algorithm (ga). Thermal conditions are overspecified at exposed surfaces amenable to measurement, while the temperature and surface heat flux distributions are unknown at the film cooling hole/slot walls. …

Nebraska Summary: S460 Case-Ih Jx65, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Experimental Validation Of A Smart-Bias Active Magnetic Bearing Controller, Shailesh Pradhananga

LSU Master's Theses

Active magnetic bearings (AMBs) are being increasingly employed in the aerospace industry in a variety of devices including compressors, turbines, pumps, and flywheels. One application of great interest to future space missions is the Integrated Power and Attitude Control System (IPACS). The IPACS consists of an arrangement of flywheels that integrates the energy storage and attitude control functions into a single system; thereby, reducing the spacecraft mass, volume, launching cost, and maintenance. Like any energy storage system, flywheels need to be operated with low power losses. AMBs are ideally suited for flywheels because they eliminate mechanical losses (friction). Nevertheless, AMBs …

A Bio-Mems Device For Separation Of Breast Cancer Cells From Peripheral Whole Blood, Juan Feng

LSU Master's Theses

This work demonstrates the application of Bio-Micro Electro Mechanical System (Bio-MEMS) technology for early breast cancer detection and diagnosis. Early breast cancer detection and diagnosis typically uses conventional mammogram screening followed by biopsy, which can be problematic since mammography can only detect highly calcified tumors greater than 1 cm in size. A micro-device was developed to identify and specifically collect tumor cells of low abundance (1 tumor cell among 10⁷ normal blood cells) from circulating whole blood. By immobilizing anti-EpCAM (Epithelial Cell Adhesion Molecule) antibodies on polymer micro-channel walls by the chemical surface modification of PMMA, breast cancer cells …

Mesoscopic Simulation Of Abnormal Grain Growth, Rakesh Kumar Behera

LSU Master's Theses

Grain growth is the process that takes place during annealing of polycrystalline materials; its major feature is a systematic increase in grain size. Two different types of grain growth can be distinguished: the normal and abnormal grain growth. During normal grain growth, the microstructure exhibits a uniform increase in grain size with time and the grain size distribution follows the log-normal distribution with the grain sizes ranging from 0 - 2.2 times the average grain size (R). On the contrary, when the abnormal grain growth is the dominant mechanism, there are certain grains (abnormal grains) in the microstructure that grow …

Design Of A Microfabricated Device For Ligase Detection Reaction (Ldr), Dwhyte Omar Barrett

LSU Master's Theses

The Ligase Detection Reaction (LDR) is a mutation detection technique used to identify point mutations in deoxyribonucleic acid (DNA). Developed by Francis Barany and associates at Cornell University it is used to find specific low abundant point mutations that may lead to colorectal cancer in the early stages of disease development. The research objective was to design and manufacture a microscale Ligase Detection Reaction (LDR) device in polycarbonate. The LDR module will be incorporated with other microdevices such as: Continuous Flow Polymerase Chain Reaction (CFRCR) and Capillary Electrophoresis (CE) in modular lab-on-a-chip technology. In making the microdevice, the duration of …

Optimal Rate Of Freezing Biological Systems, Sreedhar Thirumala

LSU Master's Theses

This thesis addresses optimization techniques for cryopreservation of biological systems. A part of the thesis (Chapter 2) reports a simplified procedure to predict the optimal rate of freezing biological systems once the cell level parameters are known a priori. The key cell level parameters investigated were, reference permeability of the membrane to water (Lpg), apparent activation energy (ELp), inactive cell volume (Vb), diameter (D), and the ratio of the available surface area for water transport to the initial volume of intracellular water (SA/WV). The simplified procedure was developed by performing a thorough analysis of the water transport model over a …

Design, Fabrication And Thermomechanical Testing Of A Vertical Bimorph Sensor In The Wafer Plane, Madhulika Sathe

LSU Master's Theses

A bimetallic recurve device was designed, fabricated and tested as a temperature sensor. The device is to be used for sensing temperatures up to 300 C inside oil wells for downhole condition monitoring. Continuous downhole measurements at high temperatures and pressures are required to monitor conditions downhole instruments are exposed to during use. Currently mercury thermometers and resistive temperature detectors (RTD) are used for downhole temperature measurements. Microsensors have potential application downhole, due to their small size and inherent robustness. The principle of a bimetallic beam was used to measure temperature. A bimetallic beam deflects with changes in temperature due …

Study Of Characteristics Of Plasma Nitriding And Oxidation Of Superalloy In738lc, Mary Shanti Pampana

LSU Master's Theses

IN738LC is a nickel base superalloy, widely used in various applications in turbine engines at high temperatures. Its oxidation and nitriding characteristics were focused in this study. Oxidation kinetics of IN738LC in dry air was studied at selected temperatures, specially chosen depending on the chemical dynamics of the alloy at such high temperatures during annealing. Isothermal oxidation in dry air was carried out at 1000°C, 1090°C, 1140°C and 1190°C. XRD results indicated an interesting onset of preferred orientation in the ã’ depleted layer in all the samples. The XPS and XRD analyses revealed the main oxide phases present in the …

Replication Of Metal-Based High-Aspect Microscale Structures By High Temperature Micromolding, Dongmei Cao

LSU Doctoral Dissertations

In microsystem technology a large range of materials will be available only after the necessary microfabrication technologies have been developed or adapted. More than a decade ago, the existing microfabrication technologies were restricted to structuring and shaping techniques producing three-dimensional microstructures out of silicon, mostly unfilled plastics or a few pure metals or binary alloys. However, the choice of materials for microcomponents is determined by the function and conditions of use of microsystems. Some microdevices can only work well when made of specific metal components. To meet this need, several microfabrication techniques have been developed, such as second electroforming of …

Algorithms For Autonomous Tandem Operation Of A Dual M113 System, Jared L. Dinkel

Dissertations, Master's Theses and Master's Reports - Open

In mid-July 2003, the U.S. Army Tank-Automotive & Armaments Command (TACOM) performed a series of experiments at Keweenaw Research Center (KRC), with a remote operated mine roller system. This system, named Panther Lite, consists of two M113 Armored Personnel Carriers (APC’s) connected by a Tandem Vehicle Linkage Assembly (TVLA). The system has three sets of mine rollers, two of which are connected to the front of the lead vehicle with one set trailing from the trail vehicle. Currently, the system requires two joystick controllers. One regulates the braking of the tracks, throttle, and transmission of the lead vehicle and …

Microscale Investigation Of Thermo-Fluid Transport In The Transition Fil, Region Of An Evaporating Capillary Meniscus Using A Microgravity Environment, Kenneth D. Kihm, Jeffrey S. Allen, Kevin P. Hallinan, David M. Pratt

Mechanical and Aerospace Engineering Faculty Publications

In order to enhance the fundamental understanding of thin film evaporation and thereby improve the critical design concept for two-phase heat transfer devices, microscale heat and mass transport is to be investigated for the transition film region using state-of-the-art optical diagnostic techniques. By utilizing a microgravity environment, the length scales of the transition film region can be extended sufficiently, from submicron to micron, to probe and measure the microscale transport fields which are affected by intermolecular forces. Extension of the thin film dimensions under microgravity will be achieved by using a conical evaporator made of a thin silicon substrate under …

Estimating Energy Savings In Compressed Air Systems, Chris Schmidt, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

Compressed air is typically one of the most expensive utilities in an industrial facility. As a result, potential savings opportunities are aggressively sought out and identified. Once identified, projected energy savings must be calculated in order to justify the cost of implementing the savings opportunity. It is important to calculate projected energy and cost savings as accurately as possible. Unfortunately, savings are frequently overestimated because the methods used to estimate savings neglect to consider important factors such as compressor control and type, storage, and multiple compressor operation.

In this paper, a methodology is presented for modeling air compressor performance and …

Architecting Design Repositories To Support Design Knowledge Storage, Reuse And Design Tool Generation, Matt R. Bohm

Masters Theses

"This collection of works describes the transformation of an existing set of heterogeneous product knowledge into a coherent design repository that supports product information archival, storage, reuse and design tool generation.

Existing product information was analyzed and compared against desired outputs to ascertain what information management structure was needed to produce design resources pertinent to the design process. Methods of incorporating non-conventional functional representations of artifacts are explored, incorporated and standardized along side conventional functional representations. A review of automatic design model generation addresses shortcomings in product representations by comparing standard hand generated design tools to computer-generated design tools. By …

Optimization Of Thermal Interface Materials For Electronics Cooling Applications, Vishal Singhal, Thomas Siegmund, Suresh V. Garimella

School of Mechanical Engineering Faculty Publications

Thermal interface materials (TIMs) are used in electronics cooling applications to decrease the thermal contact resistance between surfaces in contact. A methodology to determine the optimal volume fraction of filler particles in TIMs for minimizing the thermal contact resistance is presented. The method uses finite element analysis to solve the coupled thermo-mechanical problem. It is shown that there exists an optimal filler volume fraction which depends not only on the distribution of the filler particles in a TIM but also on the thickness of the TIM layer, the contact pressure and the shape and the size of the filler particles. …

Optimisation Of Heat Transfer And Fluid Flow In The Cooling Of Building Integrated Photovoltaic Facades., Eoin Patrick Hodge

Theses

The aim of this research was to explore the effects of mature and developing technologies from aeronautical industries such as impingement and film cooling, and electronic cooling techniques, in the setting up of different laminar and turbulent flow regimes on PV cooling duct heat transfer rates, with air flow as that brought about with natural buoyancy effects in a vertical building facade. The problem of efficiency losses in PV panels, due to overheating, is one of the factors restricting the development and use of this renewable power source. PV panels can experience very high temperatures, due to the heat input …

Nebraska Summary 446: Agco Rt135 Powermaxx Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Nebraska Summary 521: Agco Rt140a Cvt Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Nebraska Summary 447: Agco Rt150 Powermaxx Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1845: John Deere 9620t 18 Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Tests 2156 & 2157: Case Ih Jx 1060c Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Tests 2278 & 2319: Case Ih Jx 1100u Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 2228: Case Ih Mxu115 Limited Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.