Engineering Commons^™

Modelling And Validation Of A Propellant Mixer For Controller Design, Hanz Richter, Enrique Barbieri, Fernando Figueroa Nasa Stennis Space Center

Mechanical Engineering Faculty Publications

A mixing chamber used in rocket engine testing at the NASA Stennis Space Center is modelled by a system of two nonlinear ordinary differential equations. The mixer is used to condition the thermodynamic properties of cryogenic liquid propellant by controlled injection of the same substance in the gaseous phase. The three inputs of the mixer are the positions of the valves regulating the liquid and gas flows at the inlets, and the position of the exit valve regulating the flow of conditioned propellant. Mixer operation during a test requires the regulation of its internal pressure, exit mass flow, and exit …

Working Postures Of Dentists And Dental Hygienists, Richard W. Marklin, Kevin Cherney

Mechanical Engineering Faculty Research and Publications

A joint study was conducted by a manufacturer of dental stools in the Midwest of the United

States and Marquette University to measure the occupational postures of dentists and dental hygienists. The postures of 10 dentists and 10 dental hygienists were assessed using work sampling and video techniques. Postura! data of the neck, shoulders and lower back were recorded from video and categorized into 30-degree intervals: O (neutral posture of respective joint), 30, 60 and 90 degrees. Each subject's postures were observed while they were treating patients during a four-hour period, during which 100 observations of postures were recorded at …

Fabrication Of Hollow Waveguides With Sacrificial Aluminum Cores, John P. Barber, Donald B. Conkey, Jeffrey Ryan Lee, Neal B. Hubbard, Larry L. Howell, Aaron R. Hawkins, Gongliang Yin, Holger Schmidt

Faculty Publications

We have developed a process to fabricate dielectric waveguide structures with long hollow cores formed by etching a sacrificial core material. The process is compatible with other planar silicon fabrication techniques. Using aluminum as the sacrificial material, we have investigated fabrication limits and design parameters that determine mechanical integrity of the waveguides. Internal pressure due to the production of gaseous compounds during the core removal process was identified as the yield-limiting factor. A mechanical model based on finite element analysis and confirmed by experiment, predicts ultimate pressures sustainable by these structures. Waveguides less than 10 m wide with 2- m-thick …

Experimental Technique For Studying High-Temperature Phase Equilibria In Reactive Molten Metal Based Systems, Alexandre Ermoline

Dissertations

The general objective of this work is to develop an experimental technique for studying the high-temperature phase compositions and phase equilibria in molten metal-based binary and ternary systems, such as Zr-O-N, B-N-O, Al-O, and others. A specific material system of Zr-O-N was selected for studying and testing this technique.

The information about the high-temperature phase equilibria in reactive metal-based systems is scarce and their studying is difficult because of chemical reactions occurring between samples and essentially any container materials, and causing contamination of the system.

Containerless microgravity experiments for studying equilibria in molten metal-gas systems were designed to be conducted …

Computational Studies Of Viscoelastic Multiphase Flows, Shriram B. Pillapakkam

Dissertations

A finite element code based on the level set method is developed for performing two and three dimensional direct numerical simulations (DNS) of viscoelastic two-phase flow problems. The Oldroyd-B constitutive equation is used to model the viscoelastic liquid. The code is used to study transient and steady state shapes of Newtonian and viscoelastic drops in simple shear and buoyancy driven flows. The roles of the governing dimensionless parameters: Capillary number (Ca), Deborah Number (De) and the polymer concentration parameter c, in determining deformation of drops and bubbles, are also analyzed.

The numerical code permits us to vary Ca, De and …

Investigation Of Static And Dynamic Enhancement Of Laminar Natural Convection Cooling Of Electronics, Laurie Ann Florio

Dissertations

With the proliferation of consumer electronics devices and the increasingly demanding thermal control requirements for such devices, more effective and efficient means of cooling electronics are needed. The feasibility of three alternative approaches to enhancing pure natural convection cooling of electronics is investigated in the current research. The three static or dynamic methods investigated are alternate cross-flow passages, the strategic placement of transversely oscillating plates near the heat sources and a combined method using both the cross-flow passages and the strategically placed oscillating plates. These cooling methods are intended to operate in the regime for which natural convection cooling is …

Executive Summary: Evaluation Of The Impact Of Vacant Home Space Conditioning Strategies On Summer Relative Humidity, Energy, And Peak Load, Florida Solar Energy Center, Charles Withers, Jr.

FSEC Energy Research Center®

The Vacant Home Space Conditioning Study was sponsored by Florida Power & Light (FPL) as part of its Conservation R&D Program and carried out by the Florida Solar Energy Center (FSEC). In the US, about one in four retiree "snowbirds" make Florida their destination to escape the northern cold. Snowbird residents number more than 900,000 in Florida during the winter. In some counties of FPL's territory these seasonal residents compose up to 15% of the population (Shih, 1981). This pattern of seasonal occupancy creates a need for space conditioning guidelines for vacant homes to avoid mold problems while minimizing both …

A Mass-Spring-Damper Model Of A Bouncing Ball (Conference Proceeding), Mark L. Nagurka, Shuguang Huang

Mechanical Engineering Faculty Research and Publications

The mechanical properties of a vertically dropped ball, represented by an equivalent mass-spring-damper model, are related to the coefficient of restitution and the time of contact of the ball during one bounce with the impacting surface. In addition, it is shown that the coefficient of restitution and contact time of a single bounce are related to the total number of bounces and the total time elapsing between dropping the ball and the ball coming to rest. For a ball with significant bounce, approximate expressions for model parameters, i.e., stiffness and damping or equivalently natural frequency and damping ratio, are developed. …

Experimental Investigation Of Oscillatory Flow Pressure And Pressure Drop Through Complex Geometries, Mounir B. Ibrahim, Meng Wang, David Gedeon

Mechanical Engineering Faculty Publications

A series of experiments have been performed to investigate the oscillatory flow pressure and pressure drop through complex geometries. These experiments were conducted at the CSU-SLRE facility which is a horizontally opposed, two-piston, single-acting engine with a split crankshaft driving mechanism. Flow through a rectangular duct, with no insert (obstruction), was studied first. Then four different inserts were examined: Abrupt, Manifold, Diverging Short and Diverging Long. The inserts were mounted in the center of the rectangular duct to represent different type of geometries that could be encountered in Stirling machines. The pressure and pressure drop of the oscillating flow was …

A Three Dimensional Finite Element Model For Emergency Response, Xiuling Wang, Darrell W. Pepper, Yitung Chen, Sean Hsieh

Mechanical Engineering Faculty Research

No abstract provided.

Dynamic Reconfigurable Machine Tool Controller, Wei Li

Theses and Dissertations

This dissertation presents a dynamic reconfigurable control strategy based on the Direct Machining And Control (DMAC) research at Brigham Young University. A reconfigurable framework is proposed which will allow a machine tool to be controlled by a variety of applications and control laws. This Reconfigurable Mechanism for Application Control (RMAC) paradigm uses a hierarchical architecture to configure a mechanism into a device driver for direct control by an application like CAD/CAM. The RMAC paradigm is one of a mechanism device driver assigned to each mechanism class or model, and uses only the master model to control the mechanism. The traditional …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii, Third Quarterly Report, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

This quarterly report provides an update to the last phase of the Modeling, Fabrication, and Optimization of Niobium Cavities in the no-cost extension period. Designing the experimental setup of secondary electron emission was well underway in early summer of 2003 when funding was made available for this portion the study. By March 2004, many of the components of the experimental study reached UNLV with some assembly accomplished. The first secondary electron emission (SEE) measurement was made from the surface of a Faraday cup in September 2004. In December of 2005, the software for the particle positioning detector was finally up …

Characteristics Of Water-Soluble Polythiophene: Tio2 Composite And Its Application In Photovoltaics, Qiquan Qiao, Lianyong Su, James Beck, James T. Mcleskey Jr.

Mechanical and Nuclear Engineering Publications

We have studied the characteristics of composites of an environmentally friendly water-soluble polythiophene sodium poly[2-(3-thienyl)-ethoxy-4-butylsulfonate] (PTEBS) and TiO2. We observed that the ultraviolet-visible absorption spectrum of low molecular weight PTEBS is redshifted possibly due to the formation of aggregates. Cyclic voltammetry reveals the values of highest occupied molecular orbitals and lowest unoccupied molecular orbitals for PTEBS. A factor of 7 in photoluminescence quenching indicates that the exciton dissociation and charge separation occur successfully at the PTEBS: TiO2 (1:1 by weight) interface. This enhances the possibility that the separated charges will reach the electrodes before recombining. Scanning electron micrograph images show …

Filtration And Oxidation Characteristics Of A Diesel Oxidation Catalyst And A Catalyzed Particulate Filter : Development Of A 1-D 2-Layer Model, Mohammed Hasan

Dissertations, Master's Theses and Master's Reports - Open

The emissions, filtration and oxidation characteristics of a diesel oxidation catalyst (DOC) and a catalyzed particulate filter (CPF) in a Johnson Matthey catalyzed continuously regenerating trap (CCRT ®) were studied by using computational models. Experimental data needed to calibrate the models were obtained by characterization experiments with raw exhaust sampling from a Cummins ISM 2002 engine with variable geometry turbocharging (VGT) and programmed exhaust gas recirculation (EGR). The experiments were performed at 20, 40, 60 and 75% of full load (1120 Nm) at rated speed (2100 rpm), with and without the DOC upstream of the CPF. This was done to …

An Existing Global Heptane Mechanism Augmented With Diffusive Transport, Michael R. Foster, Howard Pearlman

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

The couplings between diffusive transport and the temperature and species concentration distributions associated with low and intermediate temperature heptane oxidation are explored using an existing four-step heptane mechanism, tuned for elevated pressures. The energy and species concentration equations are augmented with diffusive fluxes for heat and species and solved numerically in a one-dimensional domain. The ignition delay times are also tabulated and compared with the zero-dimensional data reported in the literature.

Quantifying Savings From Improved Boiler Operation, Kevin Carpenter, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

On/off operation and excess combustion air reduce boiler energy efficiency. This paper presents methods to quantify energy savings from switching to modulation control mode and reducing excess air in natural gas fired boilers.

The methods include calculation of combustion temperature, calculation of the relationship between internal convection coefficient and gas flow rate, and calculation of overall heat transfer assuming a parallel-flow heat exchanger model. The method for estimating savings from changing from on/off to modulation control accounts for purge and drift losses through the boiler and the improved heat transfer within the boiler due to the reduced combustion gas flow …

Integrating Functional Synthesis, William H. Wood, Hui Dong, Clive L. Dym

All HMC Faculty Publications and Research

Design couples synthesis and analysis in iterative cycles, alternatively generating solutions, and evaluating their validity. The accuracy and depth of evaluation has increased markedly because of the availability of powerful simulation tools and the development of domain-specific knowledge bases. Efforts to extend the state of the art in evaluation have unfortunately been carried out in stovepipe fashion, depending on domain-specific views both of function and of what constitutes “good” design. Although synthesis as practiced by humans is an intentional process that centers on the notion of function, computational synthesis often eschews such intention for sheer permutation. Rather than combining synthesis …

Me-Em 2005 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Overview, Mission, and Vision
• Comments on the Strategic Plan
• Enrollment and Expenditure Data
• Professional Advisory Committee
• Faculty & Staff
• Students
• Alumni
• Entrepreneurs
• Resources
• Graduates
• Publications

Machine Vision Course For Manufacturing Engineering Undergraduate Students, Jose Macedo, Kurt Colvin, Daniel Waldorf

Industrial and Manufacturing Engineering

A 10-week course was designed with funding from the Society of Manufacturing Engineers (SME) and input from industry representatives, to offer upper division engineering students a course on advanced automation. The objective was to provide engineering students theoretical and hands-on practical experience with automation technologies that will be of prime importance over the next decade: data acquisition and instrumentation, machine vision and motion control. This paper describes the machine vision portion of that class. It describes important concepts, hands-on equipment, and labs developed for this course, as well as examples of student projects from Spring Quarter, 2004. The course and …

Lead-Free Solder Joint Reliability – State Of The Art And Perspectives, Jianbiao Pan, Jyhwen Wang, David M. Shaddock

Industrial and Manufacturing Engineering

There is an increasing demand for replacing tin-lead (Sn/Pb) solders with lead-free solders in the electronics industry due to health and environmental concerns. The European Union recently passed a law to ban the use of lead in electronic products. The ban will go into effect in July of 2006. The Japanese electronics industry has worked to eliminate lead from consumer electronic products for several years. Although currently there are no specific regulations banning lead in electronics devices in the United States, many companies and consortiums are working on lead-free solder initiatives including Intel, Motorola, Agilent Technologies, General Electric, Boeing, NEMI …

Medical Technology: Contexts And Content In Science And Technology, Michael A. De Miranda, Mark Doggett, Jane T. Evans

Architectural and Manufacturing Sciences Faculty Publications

No abstract provided.

The Limits Of Reflexive Design In A Secrecy-Based Organization, Michael W. Stebbins, Tali Freed, A.B. (Rami) Shani, Kenneth H. Doerr

Industrial and Manufacturing Engineering

No abstract provided.

Test 1856: Mccormick Mtx 120 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Water-Soluble Polythiophene∕Nanocrystalline Tio2 Solar Cells, Qiquan Qiao, James T. Mcleskey Jr.

Mechanical and Nuclear Engineering Publications

We report the characteristics of polymer∕nanocrystalline solar cells fabricated using an environmentally friendly water-soluble polythiophene and TiO2 in a bilayer configuration. The cells were made by dropping the polymer onto a TiO2nanocrystallinefilm and then repeatedly sweeping a clean glass rod across the polymer as it dried. The devices showed an open circuit voltage of 0.81 V, a short circuit current density of 0.35mA/cm2, a fill factor of 0.4, and an energy conversion efficiency of 0.13%. The water-soluble polythiophene showed significant photovoltaic behavior and the potential for use in solar cells.

The Properties Of Bridgestone Ecopia Solar Car Tires (For The Umr Solar Car Team), Tessa C. Russell

Opportunities for Undergraduate Research Experience Program (OURE)

Much of the energy used by a solar car can be attributed to overcoming rolling resistance, and rolling resistance comes predominantly from the tires. The main goal of this project was to better understand the properties of the Bridgestone Ecopia tires used by the UMR Solar Car Team. Experiments were conducted to obtain this objective, measuring the vertical stiffness, lateral stiffness, and contact patch shape and area. As expected, with decreasing pressure and increasing load, the vertical and lateral deflections increased as well as the tire contact patch area. The stiffness parameters of the tire measured experimentally were used in …

An Optimized Kinetics Model For Oh Chemiluminescence At High Temperatures And Atmospheric Pressures, Joel Hall

Electronic Theses and Dissertations

Chemiluminescence from the OH(A-X) transition near 307 nm is a commonly used diagnostic in combustion applications such as flame chemistry, shock-tube experiments, and reacting-flow visualization. Measurements of the chemiluminescent intensity provide a simple, cost-effective, non-intrusive look at the combustion environment. The presence of the ultra-violet emission is often used as an indicator of the flame zone in practical combustion systems, and its intensity may be correlated to the temperature distribution or other parameters of interest. While absolute measurements of the ground-state OH(X) concentrations are well-defined, there is no elementary relation between emission from the electronically excited state (OH*) and its …

Alternative Foam Treatments For The Space Shuttle's External Tank, Kirsten Dreggors

Electronic Theses and Dissertations

The Space Shuttle Columbia accident and the recent excitement surrounding Discovery's return to space brought excessive media attention to the foam products used on the External Tank (ET). In both cases, videos showed chunks of foam or ablative material falling away from the ET during lift off. This led to several years of investigation and research into the exact cause of the accident and potential solutions to avoid the problem in the future. Several design changes were made prior to the return to flight this year, but the ET still shed foam during lift off. Since the Columbia accident, the …

Investigations On Rf Sputter Deposited Sicn Thin Films For Mems Applications, Ravi Todi

Electronic Theses and Dissertations

With the rapid increase in miniaturization of mechanical components, the need for a hard, protective coatings is of great importance. In this study we investigate some of the mechanical, chemical and physical properties of the SiCN thin films. Thin films of amorphous silicon carbide nitride (a-SiCxNy) were deposited in a RF magnetron sputtering system using a powder pressed SiC target. Films with various compositions were deposited on to silicon substrate by changing the N2/Ar gas ratios during sputtering. Nano-indentation studies were performed to investigate the mechanical properties such as hardness and reduced modulus of the SiCN films. Surface morphology of …

Electronic Commerce Negotiation In A Supply Chain Via Constraint Evaluation, R. Wilhelm, B. Chu, R. Sun

Department of Mechanical and Materials Engineering: Faculty Publications

Negotiation is of critical importance in e-commerce applications where the supply chain is dynamic and reconfiguring. In this research supply chain negotiation problems are addressed as constraint-satisfaction problems. In general each negotiation is handled in the largest scope possible to avoid the suboptimality that can result from many local solutions. This global approach, however, must be balanced with time constraints that apply in e-commerce supply chain execution. In this paper, we describe a new approach for e-commerce supply chain negotiation via constraint evaluation. As well, results from prototype software, distributed across the internet, are discussed. Beyond the general formulation, we …

Analysis Of Loading Rate Effects On Cleavage Fracture Toughness Of Ferritic Steels, Xiaosheng Gao, Robert H. Dodds Jr.

Mechanical Engineering Faculty Research

No abstract provided.