Engineering Commons^™

Evaluating The Impact Of Increased Cycling On Thermal Power Plants Due To Wind Energy Penetration In The Midwest: A Case Study, Joscelyne Larson

Electronic Theses and Dissertations

One of the most significant shifts in the mix of U.S. electricity generation over the past few years has been the rapid expansion of renewable energy resources, especially solar and wind. However, fossil fuels are still necessary to fulfill the world’s energy requirements. Despite efforts to increase the use of renewable energy sources, these sources can be at times unreliable, causing countries around the world to continue to rely on base load units such as coal and natural gas. This decrease in fossil fuels and increase in renewable energy sources presents many complex issues in terms of power system planning, …

Superhydrophobic And Oleophobic Surfaces. Synthesis And Applications, Zirui Liu

Electronic Theses and Dissertations

Surface patterning is an overwhelming approach to mechanically modifying metal surfaces and improving their tribological properties, such as repellency, lower friction, and more excellent corrosion resistance. Patterned surfaces can be applied to various industrial uses, such as cutting tools, submarines, and self-cleaning surfaces. In this paper, the novel nature-inspired flat-top-pillar "double-undercut" designs were proposed to achieve an apparent angle that satisfies super-hydrophobicity and endure higher pressure on which external forces are exerted. The main objective is to enlarge the change in Gibbs free energy for the system to exhibit a heterogeneous wetting to a homogeneous one by excavation on the …

Thermal Analysis Based Design Of Hollow Shaft For Improved Cooling Of Induction Motors, Isabelle Dinh

Electronic Theses and Dissertations

This thesis investigates methods of implanting a forced liquid convection heat recovery system within an induction motor’s shaft to cool the rotor.

The objective is to design a hollow shaft that can meet the target goals of keeping the components under an average temperature of 100℃ under different motor power conditions. Three hollow shaft design cases were studied at steady state conditions to evaluate their heat transfer performance and surface temperature to meet the goals of the study. This includes the design of a counterflow, counterflow with fins, and duct design.

It is found that third design is able to …

Fault Diagnosis Of Lubrication Decay In Reaction Wheels Using Temperature Estimation And Forecasting Via Enhanced Adaptive Particle Filter, Madhi Aldadi

Electronic Theses and Dissertations

Reaction wheel (RW), the most common Attitude Control Systems (ACS) in satellites, are highly prone to failure. A satellite needs to be oriented in a particular direction to maneuver and accomplish its mission goals; losing the RW can lead to a complete or partial mission failure. Therefore, estimating the remaining useful life (RUL) in long and short spans can be extremely valuable. The short-period prediction allows the satellite's operator to manage and prioritize mission tasks based on the RUL and increases the chances of a total mission failure becoming a partial one. Studies show that lack of proper bearing lubrication …

Experimental Improvements To A Constant Volume Combustion Chamber For Fuel Spray And Ignition Studies, Binghao Cong

Electronic Theses and Dissertations

The primary objective of this thesis is to improve optical setups of a constant volume combustion chamber to better understand the vaporization and spray characteristics of various fuels. The schlieren imaging technique is utilized to visualize phenomena that are challenging to observe directly. In this thesis, the schlieren imaging is used to observe the spray and ignition characteristics of DME and diesel fuels under high injection pressure.

First, various optical techniques are discussed and compared under the same test condition including schlieren, shadowgraph, and direct imaging. The advantages for these techniques are presented and the most appropriate technique for different …

Enhancing Traffic Safety In Unpredicted Environments With Integration Of Adas Features With Sensor Fusion In Intelligent Electric Vehicle Platform With Implementation Of Environmental Mapping Technology, David S. Obando Ortegon

Electronic Theses and Dissertations

A major objective on society is to reduce the number of accidents and fatalities on the road for drivers, and pedestrians. Therefore, the automotive engineering field is working on this problem through the development and integration of safety technologies such as advanced driving assistance systems. For this reason, this work was intended to develop and evaluate the performance of different ADAS features and IV technologies under unexpected scenarios. This by the development of safety algorithms applied to the intelligent electric vehicle designed and built in this work, through the use of ADAS sensors based on sensor fusion. Evaluation of AEB, …

Investigations Of A Surrogate Fuel Based On Fischer-Tropsch Gtl And Ctl In Cvcc, Idi And Di Compression Ignition Engines, Amanda C. Weaver

Electronic Theses and Dissertations

With the increase in availability, feedstocks, and properties of alternative fuels, compatibility issues emerge between current engine platforms often requiring a limit on the blend percentage of alternative fuel in conventional fuel or alteration to the engine platform. Two key metrics were identified, autoignition quality and lubrication characteristics, as vital for the proper function of a compression ignition engine, and if the blend of alternative fuels matches these two criteria for the diesel standard, then the resulting blend percentage can be considered as a viable alternative for complete replacement of conventional petroleum ULSD. Autoignition quality was matched using blends S-8, …

Design And Fabrication Of A Force-Displacement Control Mechanism For Bone-Surgical Tool Testing, Kenneth Nwagu

Electronic Theses and Dissertations

This project focuses on the design and fabrication of an experimental setup for orthopedic-tool testing, tailored for a surgical instrumentation company. The multifaceted project encompasses a literature review, conceptual design, prototyping, and rigorous testing, resulting in a versatile control system capable of assessing various orthopedic tools, including bone drills, saws, burrs, and power handpieces.

Orthopedic surgical procedures (which include cutting and/or drilling into bone) often need to be performed on bones for faster recovery. The drilling and cutting process can cause an increase in temperature at the cutting site which can cause bone necrosis. The tools also need to be …

Initial Procedure For Small-Scale Extraction Of Subsurface Martian Ice, Evan Steers

Electronic Theses and Dissertations

No abstract provided.

Simulating The Impact Of Emissions Control On Economic Productivity Using Particle Systems And Puff Dispersion Model, Najam Khan

Electronic Theses and Dissertations

A simulation platform is developed for quantifying the change in productivity of an economy under passive and active emission control mechanisms. The program uses object-oriented programming to code a collection of objects resembling typical stakeholders in an economy. These objects include firms, markets, transportation hubs, and boids which are distributed over a 2D surface. Firms are connected using a modified Prim’s Minimum spanning tree algorithm, followed by implementation of an all-pair shortest path Floyd Warshall algorithm for navigation purposes. Firms use a non-linear production function for transformation of land, labor, and capital inputs to finished product. A GA-Vehicle Routing Problem …

Mechanical Properties Evaluation Of 3d Printed Petg And Pctg Polymers, Kalpesh Krishnarao Bhosale

Electronic Theses and Dissertations

3D printing is also known as additive manufacturing (AM) which has become a popular manufacturing trend over the years. Due to its unique advantages of fast production rate, ability to create complex geometrical features, toolless manufacturing and many more attracts various industries from Aerospace to general cosmetics. Along with the advancement in material science, various polymers including Polylactic Acid (PLA), Polyethylene terephthalate glycol (PETG) and many more are available for 3D printing. Due to the wide range of applications in PLA, it is necessary to improve its toughness to make it more suitable by adding Poly Cyclohexylenedimethylene Terephthalate glycol (PCTG) …

An Experimental Study On The Mechanical Properties And Chemical Composition Of Lcd 3d Printed Specimens, Sebastian Gomez

Electronic Theses and Dissertations

Additive manufacturing technologies have been enhanced throughout the years yet have surprised the manufacturing industry due to their high-end surface finish and dimensional accuracy. Different experiments have been done to identify a specific phenomenon known in the vat-polymerization field. Distortion and dimensional inaccuracy tend to affect the overall properties of the process, either physical or chemical. This approach allows the understanding of how the physical properties have been affected and how to study the chemical properties to avoid this type of phenomenon. The chemical reaction between polymer and UV light has been studied and experimented with to the point that …

Development Of Corn Kernel-Based Biocomposite Films For Food Packaging Applications, Swastika Bera

Electronic Theses and Dissertations

Most of the current and active food packaging resources and methods are nonbiodegradable and nonrenewable therefore harmful to the environment. Due to this, alternate sources of food packaging materials are in high demand. In this study, a bio-composite film has been developed, with Corn kernel powder as fiber reinforcement which is mixed with gelatin, and lignin two biopolymers as the matrix. The effect of Corn Kernel (CK) reinforcement on the Gelatin/Lignin (G/L) matrix on mechanical and barrier properties has been studied. CK has shown great potential as reinforcement to natural polymer, gelatin, and lignin (G/L) for food packaging applications as …

On The Simulation Of Supersonic Flame Holder Cavities With Openfoam, Zachary Chapman

Electronic Theses and Dissertations

One of the next major advancements in the aerospace industry will be hypersonic flight. However, to achieve hypersonic flight, propulsion systems capable of reaching hypersonic speeds need to be developed. One of the more promising hypersonic propulsion systems is the scramjet engine, however, several problems still need to be explored before reliable scramjet engines can be produced, the biggest being keeping the engine ignited. This has led to the use of flame holder cavities to create a region of subsonic flow within the engine to allow combustion to occur. High experimental costs make the use of computational fluid dynamic (CFD) …

Thermoplastics 3d Printing Using Fused Deposition Modeling On Fabrics, Maxwell M. Blais

Electronic Theses and Dissertations

The creation of objects with integrated flexibility is desired and this can be achieved by additive manufacturing on fabric. We propose to use a textile fabric as a flexible joint and create to create an entire object with smaller parts called segments. Such a novel technique will bring integrated flexibility and folded assemblies using extrusion based additive manufacturing machines. The proposed process allows segments to be created flat one at a time on a continuous fabric, which will be suitable for flat to folded assemblies and eliminate size limitations of the 3D printer. Techniques considering object segmentation were used to …

Engineering The Spectrum Of Near-Field Thermal Radiation, Saman Zare

Electronic Theses and Dissertations

Thermal emission observed at sub-wavelength distances from the thermal source is referred to as near-field thermal radiation. Thermal radiation in the near-field regime can exceed Planck’s blackbody limit by orders of magnitude and be quasi-monochromatic. Due to these unique properties, near-field thermal radiation is very promising for several thermal management and energy harvesting applications. Many of these applications, such as nanogap thermophotovoltaics and thermal rectification, require near-field spectra that are not found among natural materials. Artificial metamaterials, which are engineered at the sub-wavelength scale, have been theoretically proposed for tuning the spectrum of near-field thermal radiation. However, engineering the near-field …

Computational Investigations Of The Fluid-Structure Interaction During Phonation: The Role Of Vocal Fold Elasticity And Glottal Flow Unsteadiness, Xiaojian Wang

Electronic Theses and Dissertations

Human voice production arises from the biomechanical interaction between vocal fold vibrations and airflow dynamics. Changes in vocal fold stiffness can lead to changes in vocal fold vibration patterns and further changes in voice outcomes. A good knowledge of the cause-and-effect relationship between vocal fold stiffness and voice production can not only deepen the understanding of voice production mechanisms but also benefit the treatment of voice disorders associated with vocal fold stiffness changes. This constitutes the first objective of this dissertation. The second objective of this dissertation is to further examine the range of validity of the quasi-steady assumption of …

Micro-Particle Entrainment From Density Mismatching Mixture By Dip Coating Process, S M Abu Naser Shovon

Electronic Theses and Dissertations

Solid particle transfer is a vital process for many applications such as painting, coating, materials joining, meta-surface, bio-medical applications etc. Different solid transfer techniques including welding, spray coating, roll coating etc. are available for delivering solid particles on simple structures. However, those techniques cannot effectively deliver particles to complex structures. In this thesis work, the research objective is to develop a high throughput and economical material transfer technique for complex architecture with low volumetric flux. In first part, the particle concentration of pseudo suspension was investigated in dip coating process from density mismatching mixture. The solid particles concentration was varied …

Numerical Modeling Of Localized Heating In Continuous Fiber Reinforced Thermoplastic Laminates, James T. Gayton

Electronic Theses and Dissertations

The manufacturing of continuous fiber-reinforced thermoplastic (CFRTP) laminates requires the application of heat and pressure. Standard CFRTP manufacturing methods like thermoforming take a global approach to manufacturing, where the whole part is heated and undergoes a forming process. There is an opportunity to develop advanced manufacturing methods based on localized heating and deformations of consolidated stock. This thesis provides a localized heating method via networks of resistive heating elements embedded within the laminate and a means to evaluate that method.

Typical heating methods for CFRTP laminates include infrared and convective ovens or surface contact heaters. They have the same drawbacks …

Additively Manufactured Polymer And Metal Lattice Structures With Eulerian Path, Adeeb Ibne Alam

Electronic Theses and Dissertations

Lattice structure manufacturing with polymers and metals can benefit from the use of Eulerian paths. In this research, two types of lattice fabrication methods are studied where the Eulerian path can be applicable. Polymer lattice is improved by using a new assembly design, while a new way of metal lattice fabrication is discussed.

For the fused filament fabrication process, a new interlocking design and assemble-based lattice structure building approach is investigated by increasing continuity in layers and avoiding support structures. To minimize contour plurality, Eulerian paths between the edges were enforced. Two configurations in the form of cubic and octet …

Numerical Modeling Of Vocal Control And Patient-Specific Surgical Planning Of Type 1 Thyroplasty, Mohammadreza Movahhedi

Electronic Theses and Dissertations

This study aims to develop knowledge about the roles of intrinsic laryngeal muscles on voice control in both healthy and disordered conditions through comprehensive computational models. The phonation simulator was built by combining a three-dimensional high-fidelity MRI-based model of the larynx, active muscle mechanics, and fluid-structure-acoustic interaction model, which enabled the exploration of the underlayer mechanisms of the link between individual and/or group muscles contractions under both symmetric and asymmetric activations, vocal fold posture, vocal fold vibration, and voice outcomes during voice production.

The first part of this research extensively investigated the effects of cricothyroid and thyroarytenoid muscle activations on …

Optimization Of A Lightweight Floating Offshore Wind Turbine With Water-Ballast Motion Mitigation Technology, William Ramsay

Electronic Theses and Dissertations

Floating offshore wind turbines are a promising technology to address energy needs utilizing wind resources offshore. The current state of the art is based on heavy, expensive platforms to survive the ocean environment. Typical design techniques do not involve optimization because of the computationally expensive time-domain solvers used to model motions and loads in the ocean environment. However, this project uses an efficient frequency domain solver with a genetic algorithm to rapidly optimize the design of a novel floating wind turbine concept. The concept utilizes liquid ballast mass to mitigate motions on a lightweight post-tensioned concrete platform, with a target …

Additive Manufacturing Of Aluminum Alloy By Metal Fused Filament Fabrication (Mf3)., Luke J. Malone

Electronic Theses and Dissertations

This research studies metal-fused filament fabrication (MF3) for manufacturing aluminum alloy parts. An aluminum alloy powder-based feedstock with a polymer-binder system was extruded via capillary rheometry to form a filament. The filament was used to print green parts that were involved in a two-step debinding process combining solvent and thermal extraction of the polymer binder, then sintered in a partial vacuum. Resulting grain structure, sintered density, and mechanical properties will be characterized and compared to metal injection molded (MIM) specimens. The main objective is to gain an understanding of the MF3 process characteristics and the ensuing material properties and microstructure …

Development And Applications Of A Sensor For Measurement Of Different Modes Of Heat Transfer On Foods In A Residential Oven., Kervins Petit-Bois

Electronic Theses and Dissertations

Thermal characterization of an oven is an important part of designing an oven. Understanding how changes in cooking algorithm, oven construction, and oven materials affect cooking performance is critical in ensuring that an oven is properly designed. Often temperature data is used to characterize oven behavior, but this neglects the mode of heat transfer used to achieve these temperatures. Several studies have compared the different modes of heat transfer and cooking performance and have shown that cooking performance in radiation dominated modes are different than in convection dominated modes. The goal of this study is to develop a heat flux …

Experimental Evaluation Of Heat Leak From Anti-Sweat Components Into Fresh Food And Freezer Compartments Of A Household Refrigerator., Delva Felissaint

Electronic Theses and Dissertations

Condensation beads forming on outside surfaces around a refrigerator is an undesirable byproduct driven by the cold temperature exhibited throughout the unit. To combat this issue, anti-sweat components usually in the form of electrical heaters or tubes carrying hot refrigerant, bring heat to the cold surfaces to ensure their temperatures do not drop below the dew point. Some heat produced by the anti-sweat components may transfer to the interior refrigerated compartment. The purpose of this study is to quantify how much heat from the anti-sweat components are entering the fresh food and freezer compartments and what impact that has on …

Enhancing Thermoelectric Generator Performance, Xi William Wang

Electronic Theses and Dissertations

Waste heat recovery plays an important role for alleviating the energy crisis and mitigating climate change. The thermoelectrical generator (TEG), a solid energy convertor, is a promising technology. However, the performance of a TEG is sensitive to its geometric structure and working conditions. An improved geometric structure and matching to the working conditions can make a TEG fully utilize its thermoelectrical conversion potential.

The TEG optimization is a kind of combinatorial problem. An effective algorithm is needed to optimize a TEG’s performance. The particle swarm optimization (PSO) algorithm is introduced in this study to optimize a TEG’s output power, efficiency, …

Joining Methods For Continuous Fiber Reinforced Thermoplastic Composites In Structural Applications, Andrew Moran

Electronic Theses and Dissertations

Continuous fiber reinforced thermoplastic (CFRTP) composites have been proposed as an alternative to metals in structural applications. CFRTP composites can be used to create structures that are lighter weight, have better resistance to environmental factors, and have the potential to be recycled. However, one of the main challenges to CFRTP composites is connections between structural members. The goal of this thesis is to investigate the feasibility of joining CFRTP composites to both similar and dissimilar materials through literature review, coupon testing, design of a structural joint, and a small scale laboratory prototype of the joint. To achieve this goal the …

Development And Characterization Of Bound Metal Deposition Including Laser Ablation, Alexander J. Watson

Electronic Theses and Dissertations

Bound Metal Deposition (BMD) is a novel metal additive manufacturing technology in which a metal powder-binder composite paste is layer-wise extruded to form a part, which is then debound and sintered into a solid metal part. Although promising, BMD suffers from shrinkage-induced warpage and an inability to produce fine length scale features. This research addresses these problems by: (1) characterizing warpage of planar parts, and (2) developing a novel laser ablated process to create fine length scale features. First, a 12-factor resolution IV fractional-factorial design of experiments (DOE) was conducted to determine the warpage of planar parts as a function …

Development Of A Structural Finite Element Modeling Approach For Hybrid Composite-Steel Shipping Containers, Jason Nagy

Electronic Theses and Dissertations

This thesis presents a summary of the development and verification of structural finite element (FE) models for predicting key responses of ISO composite-steel shipping containers. The container has a steel perimeter frame with composite corrugated panels bonded to steel tabs welded to the frame. This thesis presents the development of the FE models to predict structural behavior when the container under goes select International Standards Organization standard 1496-1 structural tests. Composite and steel mechanical properties were predicted and matched to measured data from coupon tests. Individual panels were modeled and matched to individual three-point bending tests. The individual panel models …

Development And Evaluation Of Modeling Approaches For Extrusion-Based Additive Manufacturing Of Thermoplastics, Christopher C. Bock

Electronic Theses and Dissertations

This work focuses on evaluating different modeling approaches and model parameters for thermoplastic AM, with the goal of informing more efficient and effective modeling approaches. First, different modeling approaches were tested and compared to experiments. From this it was found that all three of the modeling approaches provide comparable results and provide similar results to experiments. Then one of the modeling approaches was tested on large scale geometries, and it was found that the model results matched experiments closely. Then the effect of different material properties was evaluated, this was done by performing a fractional factorial design of experiments where …