Engineering Commons^™

The Importance Of Accurately Predicting Corner Separations In Fan Stall Point Identification With Steady Rans: Computations With The Helicity-Corrected Spalart-Allmaras Turbulence Model, Zhifan Yu

Electronic Theses and Dissertations

This thesis applies a modified Spalart-Allmaras (SA) turbulence model, the helicity-corrected Spalart-Allmaras (HCSA) model, in incompressible steady Reynolds-averaged Navier-Stokes (RANS) computations to reduce the numerical simulation run time for fan stall inception prediction. Computations are carried out using the OpenFOAM package. This manuscript-style thesis contains two main chapters, each stemming from conference papers. First, the HCSA turbulence model is applied to a low-speed axial fan, known as the boundary layer ingestion (BLI) fan, for fan stall behavior simulation. Both RANS and unsteady RANS (URANS) with the HCSA model and RANS with the original SA model are performed, with all results …

Model-Guided Extremum Seeking Control For Mechanical Ventilators, Ryan Keith Wardell

Electronic Theses and Dissertations

Mechanical ventilators are an important lifesaving medical device and because of the COVID-19 pandemic, they were in a massive demand for them to help the patients most severely affected by the disease. A large number of open-source hardware ventilator projects were established during the pandemic, most of which did not provide sufficient information on the design of their control systems. In this thesis, a model-guided extremum seeking control scheme is proposed for use on a open-source hardware ventilator design. The performance of the control scheme is intended to not be significantly affected by changes to the patient, nor to variations …

Fully Coupled Fluid Structure Interaction Simulation Of Bioprosthetic Heart Valves: A Numerical And Experimental Analysis, Masod Sadipour

Electronic Theses and Dissertations

Aortic stenosis impacts approximately 7% of the global population. In the past decade, the role of computational modeling has been becoming considerably important in the design of BHVs. To obtain reliable solutions in computational modeling, it is essential to consider accurate properties of bioprosthetic heart valves (BHVs), such as density and mechanical properties. Previous computational studies assumed (bovine pericardium) BP used in BHVs density was comparable to water or blood. Yet, BP is subjected to multiple treatments like fixation and anti-calcification. In Chapter 2, I measured BP density and its effect on BHV leaflet stress and strain. In the second …

Patient Movement Monitoring Based On Imu And Deep Learning, Mohsen Sharifi Renani

Electronic Theses and Dissertations

Osteoarthritis (OA) is the leading cause of disability among the aging population in the United States and is frequently treated by replacing deteriorated joints with metal and plastic components. Developing better quantitative measures of movement quality to track patients longitudinally in their own homes would enable personalized treatment plans and hasten the advancement of promising new interventions. Wearable sensors and machine learning used to quantify patient movement could revolutionize the diagnosis and treatment of movement disorders. The purpose of this dissertation was to overcome technical challenges associated with the use of wearable sensors, specifically Inertial Measurement Units (IMUs), as a …

The Modernization Of Large Power Transformer Tanks, Babajide O. Williams

Electronic Theses and Dissertations

Due to the current demands placed on the power grid in terms of climate change, increasing urbanization, and terrorist attacks, the U.S. government in response to these demands, mandated that all the grid components be modernized in order to increase their reliability. As a critical component of the grid, Large Power Transformers (LPTs) play a key role in ensuring sustainable power generation and distribution. A literature search performed in this work and the analysis of data retrieved from the search showed that the tanks of these LPTs are critical to their durability, longevity, and reliability. Therefore, the reliability of LPTs …

Novel Approach For Non-Invasive Prediction Of Body Shape And Habitus, Emma Young

Electronic Theses and Dissertations

While marker-based motion capture remains the gold standard in measuring human movement, accuracy is influenced by soft-tissue artifacts, particularly for subjects with high body mass index (BMI) where markers are not placed close to the underlying bone. Obesity influences joint loads and motion patterns, and BMI may not be sufficient to capture the distribution of a subject’s weight or to differentiate differences between subjects. Subjects in need of a joint replacement are more likely to have mobility issues or pain, which prevents exercise. Obesity also increases the likelihood of needing a total joint replacement. Accurate movement data for subjects with …

Efficient Sintering Of Lunar Soil Using Concentrated Sunlight, Diprajit Biswas

Electronic Theses and Dissertations

Construction material is one crucial need for long-term habitation on the moon. When concentrated for high heat flux, solar radiation can heat lunar soil or regolith until it sinters at temperatures above 900°C. The solid, sintered soil simulant can be used as construction material. This work explores the conditions leading to effective lunar soil sintering for both direct and indirect irradiated sintering. Lunar soil simulants were sintered using concentrated light from a xenon-arc lamp with varying heat flux intensity. During direct sintering of LHS-1, a sintering range of 860°C-1140°C corresponding to a peak heat flux of 105-120 kW/m2 was identified …

The Future Is Now In Twisted Coil Polymer Actuators (Tcpa), Ryan Ronquillo

Electronic Theses and Dissertations

This thesis aimed to fabricate and test twisted coiled polymer actuators (TCPA) to understand the mechanical and thermal aspects of this artificial muscle fiber. The purpose of this thesis was to find a linear relationship using the LVDT sensor, fabricating TCPA fibers, and interpreting the data. The project tested whether nylon/polymer could be used as a better artificial muscle fiber.

This research accomplished three goals: (1) designing and fabricating a system capable of creating supercoiled muscle fibers consistently, (2) calibrating the Linear Variable Differential Transformer (LVDT) and Core, and (3) analyzing/interpreting the data of the Twisted Coiled Polymer Actuators (TCPA) …

Investigating The Effectiveness Of A Haptic Feedback System To Improve The Gait Speed Of Older Adults In Overground Walking, Md Tanzid Hossain

Electronic Theses and Dissertations

While the use of tactile feedback for modifying gait has recently shown promising results in a number of research studies, there has been little attention given to its ability to effect change in the gait of older adults nor has the effect of the frequency of this feedback been examined. Given the important associations of walking speed with the health of older adults, the goal of this study was to determine if a recently developed haptic feedback system could increase the walking speed of older adults and whether the frequency at which this feedback was provided would have an impact …

Application Of Particle Transfer By Dipping Using Polymer Binder, Md Ibrahim Khalil

Electronic Theses and Dissertations

The demand for particle transfer is increasing in various industries, such as manufacturing, metal joining, microfluidics, roller lubrication process, fuel cells, super-capacitors, hybrid coating, and protective layer applications. As a result, the importance of efficient transfer of solid micron-size particles is becoming more crucial. Submicron-sized particles can easily adhere to solid substrates due to negligible gravitational force, while micron-sized or larger particles require a binder to overcome the gravitational effects. This thesis aims to investigate the interactions between microparticles and polymer thin film on cylindrical substrates using particle transfer methods. The process parameters are optimized and demonstrated two applications of …

Mechanics And Mechanisms Of Fracture For An Eastern Spruce Subject To Transverse Loading Using Acoustic Emission, Parinaz Belalpour Dastjerdi

Electronic Theses and Dissertations

Due to its excellent structural qualities and accessibility, wood is among the most often utilized structural materials. Despite its ubiquity, wood poses numerous challenges. It is heterogeneous and anisotropic. It has a complex hierarchical ultrastructure, and the properties can have wide variation within a species, and indeed within an individual tree. This work aims to improve our understanding of the strength and fracture behavior of spruce-pine-fir (south) (SPFs), particularly in cross-grain direction. This study’s primary goal is to examine the relationship between crack propagation and cross grain morphology under the following loading configurations: compact tension, compression, and rolling shear. The …

Feasibility Of Thermoplastic Extrusion Welding As A Joining Method For Vacuum-Assisted Additively Manufactured Tooling, Chase C. Flaherty

Electronic Theses and Dissertations

In recent years, additive manufacturing (AM) has been successfully utilized for the production of large-scale composite tooling. Within these endeavors, however, limited research has focused on joining methods between printed sections. This work evaluates the feasibility of thermoplastic extrusion welding as a joining method for additively manufactured tooling structures. This joining method was assessed based on industry specifications of conventional thermoset tooling for wind blade manufacturing utilizing the vacuum-assisted resin transfer molding (VARTM) process. The specifications include requirements for the mechanical strength, vacuum integrity, roughness, and hardness of the tool surface. The feasibility of this welded polymer joint was demonstrated …

Investigation Into Sintered Lunar Regolith Construction Methods And Novel Usability Evaluation, Thomas A. Cox

Electronic Theses and Dissertations

Since the Apollo missions in the late 1960's, there has been a growing interest shared by many countries around the world to return to the Moon and establish a permanent Lunar settlement. The first phase of temporary Lunar bases will be established over the next several years. For a permanent human presence on the Moon, it will be necessary to use locally available resources for the construction of Lunar habitats and other infrastructure. Sintering Lunar regolith has been shown to be a promising method for producing structural material with a variety of desirable properties from strength to radiation shielding. While …

Modeling, Simulation And Control Of Microrobots For The Microfactory., Zhong Yang

Electronic Theses and Dissertations

Future assembly technologies will involve higher levels of automation in order to satisfy increased microscale or nanoscale precision requirements. Traditionally, assembly using a top-down robotic approach has been well-studied and applied to the microelectronics and MEMS industries, but less so in nanotechnology. With the boom of nanotechnology since the 1990s, newly designed products with new materials, coatings, and nanoparticles are gradually entering everyone’s lives, while the industry has grown into a billion-dollar volume worldwide. Traditionally, nanotechnology products are assembled using bottom-up methods, such as self-assembly, rather than top-down robotic assembly. This is due to considerations of volume handling of large …

Drop Impact On Dry And Liquid Infused Substrates With Micro-Wells., Ahmed Nazrul Islam

Electronic Theses and Dissertations

Drop impact on different types of surfaces are important physical concepts that are routinely found in day-to-day life and such studies have immense application for various types of industries. One such important application of drop dynamics is in the field of aviation science which is concerned of very large freezing drizzle drops impacting on airplane wings. Such drops are known as supercooled large droplets (SLD), and they pose a great risk and have been long known to have caused notable accidents in the past. SLDs are liquid drops that can remain in the state of liquid phase and grow into …

Super P-Sulfur Cathodes For Quasi-Solid-State Lithium-Sulfur-Batteries., Milinda Bharatha Kalutara Koralalage

Electronic Theses and Dissertations

Lithium-Sulfur (Li-S) batteries have become a promising candidate to meet the current energy storage demand, with its natural abundance of materials, high theoretical capacity of 1672 mAhg-1, high energy density of 2600 Whkg-1, low cost and lower environmental impact. Sulfide based solid state electrolytes (SSEs) have received greater attention due to their higher ionic conductivity, compatible interface with sulfur-based cathodes, and lower grain boundary resistance. However, the interface between SSEs and cathodes has become a challenge in all solid-state Li-S batteries due to the rigidity of the participating surfaces. A hybrid electrolyte containing SSE coupled with a small amount of …

Engineering 3d Architected Metamaterials For Enhanced Mechanical Properties And Functionalities., Huan Jiang

Electronic Theses and Dissertations

Compared with conventional materials, architected metamaterials have shown unprecedented mechanical properties and functionalities applications. Featured with controlled introduction of porosity and different composition, architected metamaterials have demonstrated unprecedent properties not found in natural materials. Such design strategies enable researchers to tailor materials and structures with multifunctionalies and satisfy conflicting design requirements, such as high stiffness and toughness; high strength with vibration mitigation properties, etc. Furthermore, with the booming advancement of 3D printing technologies, architected materials with precisely defined complex topologies can be fabricated effortlessly, which in turn promotes the research significantly. The research objectives of this dissertation are to achieve …

Assessing The Economic Feasibility Of Capturing And Utilizing Carbon Dioxide From Ethanol Production In South Dakota, Makiah Stukel

Electronic Theses and Dissertations

Since the Industrial Revolution, anthropogenic greenhouse gas (GHG) emissions have spiked dramatically, prompting discussions on climate change. Mitigating climate change requires significant reductions in global carbon dioxide (CO2) emissions as CO2 is the most abundant anthropogenic GHG. A process that assists in offsetting the exponential growth in CO2 emissions is carbon capture and storage (CCS). Integrating carbon capture technology into the ethanol industry can provide an economically feasible way to achieve net reductions in CO2 emissions. The proposed work investigates the economic viability of applying CCS technologies to the 16 ethanol facilities in South Dakota (SD) and quantifies the potential …

Quantifying The Effects Of Hvac Operation To Mitigate Aerosol Concentration In A Classroom Using Cfd, Scott Deprez

Electronic Theses and Dissertations

Heating, ventilation, and air conditioning (HVAC) is a complex mechanical system for the transition of air between outdoor and indoor areas. These systems are directly responsible for temperature, humidity, and air flow into any given space, thereby providing a level of comfort to those who live indoors. These systems account for 52 percent of U.S. energy consumption. When designing HVAC systems, indoor air quality (IAQ) is the main focus for achieving safe and clean air, such as in the case of airborne diseases. HVAC systems are responsible for the flow of air in indoor spaces and thereby expand the transmissible …

Modeling Of Transport In Anatomic Respiratory Airways: Applications In Targeted Drug Delivery And Airborne Pathogenic Transmissions, Mohammad Mehedi Hasan Akash

Electronic Theses and Dissertations

This thesis aims to explore the potential of improving the efficacy of drugs for treatment of viral infections by targeting the nasopharynx, which is commonly the first site of infection for many viral pathogens. Currently, intranasal sprays are used, but the standard protocol (“Current Use” or CU) results in suboptimal drug deposition at the nasopharynx. To address this issue, an “Improved Use” or, IU protocol has been proposed, which involves pointing the spray bottle at a shallower angle and aiming slightly towards the cheeks. The IU delivery is also robust to perturbations in spray direction, which highlights the practical utility …

Evaluating The Impact Of Increased Cycling On Thermal Power Plants Due To Wind Energy Penetration In The Midwest: A Case Study, Joscelyne Larson

Electronic Theses and Dissertations

One of the most significant shifts in the mix of U.S. electricity generation over the past few years has been the rapid expansion of renewable energy resources, especially solar and wind. However, fossil fuels are still necessary to fulfill the world’s energy requirements. Despite efforts to increase the use of renewable energy sources, these sources can be at times unreliable, causing countries around the world to continue to rely on base load units such as coal and natural gas. This decrease in fossil fuels and increase in renewable energy sources presents many complex issues in terms of power system planning, …

Superhydrophobic And Oleophobic Surfaces. Synthesis And Applications, Zirui Liu

Electronic Theses and Dissertations

Surface patterning is an overwhelming approach to mechanically modifying metal surfaces and improving their tribological properties, such as repellency, lower friction, and more excellent corrosion resistance. Patterned surfaces can be applied to various industrial uses, such as cutting tools, submarines, and self-cleaning surfaces. In this paper, the novel nature-inspired flat-top-pillar "double-undercut" designs were proposed to achieve an apparent angle that satisfies super-hydrophobicity and endure higher pressure on which external forces are exerted. The main objective is to enlarge the change in Gibbs free energy for the system to exhibit a heterogeneous wetting to a homogeneous one by excavation on the …

Thermal Analysis Based Design Of Hollow Shaft For Improved Cooling Of Induction Motors, Isabelle Dinh

Electronic Theses and Dissertations

This thesis investigates methods of implanting a forced liquid convection heat recovery system within an induction motor’s shaft to cool the rotor.

The objective is to design a hollow shaft that can meet the target goals of keeping the components under an average temperature of 100℃ under different motor power conditions. Three hollow shaft design cases were studied at steady state conditions to evaluate their heat transfer performance and surface temperature to meet the goals of the study. This includes the design of a counterflow, counterflow with fins, and duct design.

It is found that third design is able to …

Fault Diagnosis Of Lubrication Decay In Reaction Wheels Using Temperature Estimation And Forecasting Via Enhanced Adaptive Particle Filter, Madhi Aldadi

Electronic Theses and Dissertations

Reaction wheel (RW), the most common Attitude Control Systems (ACS) in satellites, are highly prone to failure. A satellite needs to be oriented in a particular direction to maneuver and accomplish its mission goals; losing the RW can lead to a complete or partial mission failure. Therefore, estimating the remaining useful life (RUL) in long and short spans can be extremely valuable. The short-period prediction allows the satellite's operator to manage and prioritize mission tasks based on the RUL and increases the chances of a total mission failure becoming a partial one. Studies show that lack of proper bearing lubrication …

Experimental Improvements To A Constant Volume Combustion Chamber For Fuel Spray And Ignition Studies, Binghao Cong

Electronic Theses and Dissertations

The primary objective of this thesis is to improve optical setups of a constant volume combustion chamber to better understand the vaporization and spray characteristics of various fuels. The schlieren imaging technique is utilized to visualize phenomena that are challenging to observe directly. In this thesis, the schlieren imaging is used to observe the spray and ignition characteristics of DME and diesel fuels under high injection pressure.

First, various optical techniques are discussed and compared under the same test condition including schlieren, shadowgraph, and direct imaging. The advantages for these techniques are presented and the most appropriate technique for different …

Enhancing Traffic Safety In Unpredicted Environments With Integration Of Adas Features With Sensor Fusion In Intelligent Electric Vehicle Platform With Implementation Of Environmental Mapping Technology, David S. Obando Ortegon

Electronic Theses and Dissertations

A major objective on society is to reduce the number of accidents and fatalities on the road for drivers, and pedestrians. Therefore, the automotive engineering field is working on this problem through the development and integration of safety technologies such as advanced driving assistance systems. For this reason, this work was intended to develop and evaluate the performance of different ADAS features and IV technologies under unexpected scenarios. This by the development of safety algorithms applied to the intelligent electric vehicle designed and built in this work, through the use of ADAS sensors based on sensor fusion. Evaluation of AEB, …

Investigations Of A Surrogate Fuel Based On Fischer-Tropsch Gtl And Ctl In Cvcc, Idi And Di Compression Ignition Engines, Amanda C. Weaver

Electronic Theses and Dissertations

With the increase in availability, feedstocks, and properties of alternative fuels, compatibility issues emerge between current engine platforms often requiring a limit on the blend percentage of alternative fuel in conventional fuel or alteration to the engine platform. Two key metrics were identified, autoignition quality and lubrication characteristics, as vital for the proper function of a compression ignition engine, and if the blend of alternative fuels matches these two criteria for the diesel standard, then the resulting blend percentage can be considered as a viable alternative for complete replacement of conventional petroleum ULSD. Autoignition quality was matched using blends S-8, …

Design And Fabrication Of A Force-Displacement Control Mechanism For Bone-Surgical Tool Testing, Kenneth Nwagu

Electronic Theses and Dissertations

This project focuses on the design and fabrication of an experimental setup for orthopedic-tool testing, tailored for a surgical instrumentation company. The multifaceted project encompasses a literature review, conceptual design, prototyping, and rigorous testing, resulting in a versatile control system capable of assessing various orthopedic tools, including bone drills, saws, burrs, and power handpieces.

Orthopedic surgical procedures (which include cutting and/or drilling into bone) often need to be performed on bones for faster recovery. The drilling and cutting process can cause an increase in temperature at the cutting site which can cause bone necrosis. The tools also need to be …

Initial Procedure For Small-Scale Extraction Of Subsurface Martian Ice, Evan Steers

Electronic Theses and Dissertations

No abstract provided.

Simulating The Impact Of Emissions Control On Economic Productivity Using Particle Systems And Puff Dispersion Model, Najam Khan

Electronic Theses and Dissertations

A simulation platform is developed for quantifying the change in productivity of an economy under passive and active emission control mechanisms. The program uses object-oriented programming to code a collection of objects resembling typical stakeholders in an economy. These objects include firms, markets, transportation hubs, and boids which are distributed over a 2D surface. Firms are connected using a modified Prim’s Minimum spanning tree algorithm, followed by implementation of an all-pair shortest path Floyd Warshall algorithm for navigation purposes. Firms use a non-linear production function for transformation of land, labor, and capital inputs to finished product. A GA-Vehicle Routing Problem …