Engineering Commons^™

Mechanical Engineering Education In Irish Context: On Route To Becoming A Chartered Engineer, David Kennedy, Richard Good

Conference Papers

Engineering Education in Ireland and throughout Europe has changed dramatically over the last few years and the pace of change is ensuring that we, the educators are constantly keeping abreast of new developments and benchmarks. Programmes that were based on inputs from learners are now outcomes based and the onus is on the educators and facilitators to provide evidence that graduates are capable of conducting specific tasks, commonly termed as Programme Outcomes. Similarly, greater onus is now placed on the learner to take greater responsibility for their educational development. The new and current process of meeting the educational requirements of …

Design Issues For Therapeutic Ultrasound Angioplasty Waveguides, Declan Noone, Graham Gavin, Garrett Mcguinness

Conference Papers

Therapeutic ultrasound angioplasty is a new minimally invasive cardiovascular procedure for disrupting atherosclerotic lesions. Mechanical energy is transmitted in the form of ultrasound waves via long, flexible wire waveguides navigated to the lesion site through the vascular system. The underpinning principle of this technology is that plaque may be disrupted through a combination of direct contact ablation, pressure waves, cavitation and acoustic streaming, which all depend on the amplitude and frequency of displacements at the distal tip of the wire waveguide. This study identifies a number of key design issues for clinical devices of this type, and describes testing procedures …

Preparation And Accreditation Of Level 7 Engineering Programmes, Mark Mcgrath

Conference Papers

Accreditation of 3^rd level educational programmes by a suitably recognised professional body is of particular relevance in relation to engineering. The completion of a sequence of modules which leads to the attainment of this professionally recognised award is viewed as integral to the undertaking. The engineering technology fields are developing and expanding rapidly and the third level sector must keep abreast of these changes. This is essential if the third level institutions wish to continue delivering programmes which produce graduates who can successfully complete the transition from 3rd. Level to the various engineering sectors.

This paper outlines various aspects …

Exchange Faculty Perspectives On International Collaborations, Donal Mchale

Conference Papers

The main purpose of the paper is to document key issues in developing successful transatlantic faculty exchanges and to document perspectives and key learnings’ emanating from the development and implementation of an international exchange process.

Indentation Fracture Of Bovine Cortical Bone: Acoustic Emission Technique, Ashkan Safari, Ger Reilly, Brendan Mccormack

Conference Papers

Indentation cutting may result in microcracking and main crack growth which was previously reported. In this study, we recorded the AE signals produced by cracking processes during cutting on cortical bone, measuring the cutting force and correlating between load-displacement curves and AE activities.

A Numerical Acoustic Fluid-Structure Model Of A Therapeutic Ultrasound Angioplasty Device, Graham Gavin, M.S. J. Hashmi, Finbar Dolan, Garrett Mcguinness

Conference Papers

Ultrasonic angioplasty involves the use of ultrasonic vibrations delivered to the distal-tip of small diameter wire waveguides and is an emerging technology the may have potential use in the treatment of complicated atherosclerotic plaques during cardiovascular surgery. Complicated plaques, including chronic total occlusions and calcified lesions, seriously reduce success rates during standard intervention involving guidewire access, followed by balloon dilation or stent delivery. The large amplitude (0-150 μm) wire waveguide distal-tip displacements in the low-frequency ultrasonic (18-45 kHz) range have been shown to disrupt plaque material by direct contact ablation and cavitation, acoustic streaming and pressure wave components in adjacent …

Alkaline Fuel Cell Engineering And Testing, James Brunton, David Kennedy, Eugene Coyle

Conference Papers

A fuel cell is a device that directly converts the chemical energy of reactants (a fuel and an oxidant) into low d. c. electricity [1]. Used in conjunction with other sustainable energy options, hydrogen and fuel cell technology can provide a realistic alternative to fossil fuels. Although research is continuing in many areas we are no closer now to commercialisation than ten to twenty years ago. This is due to a number of key reasons, some of which include efficiency, scale, accessories and power output. This paper outlines the benefits that could be derived from switching to a hydrogen based …

The Tromped, An In-Flight Exercise Device To Prevent Flight Related Deep Vein Thrombosis, Carolyn Collins, David Kennedy, Thomas Corrigan, Stephen Jerrams

Conference Papers

Medical and Engineering research studies have shown the potential risks of long haul flight travel and methods of preventing it occurring. The risk of serious health problems or even death is known to arise from lack of venous movement and increased coagulation (clotting) of the blood. These factors contribute to the development of deep vein thrombosis (DVT) and this is more likely to occur in situations where people are seated for long periods during travel on land or in air. Currently long haul airlines have yet to be seen to introduce physical preventative measures against this syndrome.

A prototype design …

The Role And Future Of Nanotechnology In Research, Industry And Education, David Kennedy

Conference Papers

Major developments in Nanotechnology have taken place across the world
over the last few years. From a humble beginning, Ireland inc. became a leader in the Microelectronics industry and now has to face the challenge of developing a strategic plan to maintain its lead position in the nano field which in most cases will supersede the micro phase. Most countries are taking a similar path of development all be it alone or in collaboration with other countries. This process is expensive and requires market drivers and experts to lead and deliver demands from the industries of the future. The approach …

A Numerical Acoustic Fluid-Structure Simulation Of Therapeutic Ultrasound Angioplasty, Graham Gavin, Finbar Dolan, M.S J. Hashmi, Garrett Mcguinness

Conference Papers

INTRODUCTION Therapeutic ultrasound angioplasty is the delivery of high amplitude ultrasonic displacements to the distal-tip of small diameter wire waveguides with the goal of disrupting atherosclerotic plaques. This is a minimally invasive procedure that may have potential' in the treatment of complicated chronic total occlusions. The disruption of plaque is due to direct contact ablation and also cavitation, pressure waves and acoustic streaming in the fluid surrounding the vibrating waveguide distal-tip [1]. Cavitation appears to play a major role and some authors have suggested that plaque ablation is only evident above the cavitation threshold [2]. Makin and Everbach [3] performed …

Analysis Of Indentation Loading Of Cortical Bone Using Acoustic Emission Techniques, Ashkan Safari, Ger Reilly, Brendan Mccormack

Conference Papers

In this study, we recorded the number of Acoustic emission (AE) hits and related AE energy during indentation fracture of cortical bone using a PAC PCI-2 card and pico sensor. A threshold value of 43dB was used to filter premature trigger due to background noise. Registered AE hits had more than one count (threshold crossing). Amplifier gain was set at 40dB with a (0.1-1) MHz band pass filter. 8mm cubes of cortical bones were indented in the longitudinal direction at constant crosshead speed of 1 mm min-1 using a large 2D, 50˚ wedge indenter. We hypothesised that signals occurring as …

Manufacture Of Near Net Shaped 3-Dimensional Components For Industrial Applications, David Kennedy, Donal Brosnan

Conference Papers

The development of near net shape 3-Dimensional products for industrial applications has been one main goal for Manufacturing Industries over the last few decades. Processes such as polymer blow moulding and its various stages of development, glass forming, extrusion, forging, centrifugal and sand casting, bulge forming and vacuum forming are typical processes that have contributed to this development. Current practices centre on Surface coatings, Rapid Prototyping, laser forming and nanotechnology manufacture of complex 3-D shapes and assemblies. The work described in this paper is a new and highly efficient and cost effective technique for producing 3-Dimensional thin walled shapes by …

An Investigation On The Suitability Of Surface Engineered Austempered Ductile Iron As A Gear Material, M. Grech, David Kennedy, Zdravko Schauperl

Conference Papers

This preliminary study demonstrates that surface engineered austempered ductile iron is a valid alternative gear material to carburised steel. The impact energy of ductile cast iron samples in various conditions, including as – cast, austempered at 240^oC and austempered and shot peened using both 0.7mm and 1.4mm steel balls, was measured. As expected the as-cast material exhibited nominal impact energy. This has been attributed mainly to the pearlitic matrix structure.Austempering generally increases the impact energy. The extent of the improvement is however dependent on the austempering temperature and the resulting microstructure. It was shown that the structure following …

An Acoustic Fluid-Structure Simulation Of A Therapeutic Ultrasound Wire Waveguide Apparatus, Graham Gavin, M. Hashmi, Finbar Dolan, Garret Mcguinness

Conference Papers

The use of high-power low-frequency ultrasound transmitted down small diameter wire waveguides is an emerging technology that may have potential in the treatment of complicated atherosclerotic plaques in cardiovascular surgery. This form of energy delivery results in vibrating the distal-tip of the wire waveguide disrupting material by means of direct contact ablation and also cavitation, pressure waves and acoustic streaming in the surrounding fluid. This work describes a numerical acoustic fluid-structure model of the ultrasound wire waveguide and blood surrounding the distal tip. The structural analysis of the model predicts the natural frequencies of the waveguide and shows the extent …

Development And Performance Characteristics Of An Ultrasound Angioplasty Device, Graham Gavin, Garrett Mcguinness, Finbar Dolan, M.S. J. Hashmi

Conference Papers

INTRODUCTION The effect of atherosclerosis is well documented and many procedures such as balloon angioplasty and stentimplantation have been developed to reopen occluded arteries. However, there are considerable differences in the material properties of various atherosclerotic lesions as they develop. Many authors have suggested that rigid calcified plaques may require specific procedures that target this rigid material through de-bulking or complete removal (Salunke et al, 1997). Ultrasound angioplasty is the delivery of high power low frequency ultrasound via a wire waveguide to the lesion location. This results in distal tip wire displacements of up to 100um peak-to-peak (p-p) at frequencies …

Pressure Distribution Around Spherical Distal Ball-Tip In Ultrasound Angioplasty, Graham Gavin, Garrett B. Mcguinness, Finbar Dolan, M.S. J. Hashmi

Conference Papers

INTRODUCTION Ultrasound Angioplasty has been shown to be effective in the removal and re-canalising of blockages in arteries (Siegel RJ, 1993). By delivering therapeutic ultrasound to the blockage, via a wire waveguide to a ball-tip, the lesion or thrombus is affected by pressure waves, micro streaming, cavitation and direct contact with the oscillating ball-tip. Most work to date has concentrated on a spherical ball-tip geometry at the distal end of the wire waveguide (Steffen, 1994 and Rosenschein, 1996). Tip displacements usually lie between 10 - 100m (peak-to peak) and ball tip diameters between 1 - 2mm (Atar, 1999 and Yock, …

Investigation Of Four-Wheel Steering Algorithms For A Formula Sae Car, Colm O'Kane, Sean Timoney

Conference Papers

An algorithm was developed for a speed-dependent four-wheel steering system for a Formula SAE car. A linear bicycle model was implemented using the MATLAB and SIMULINK software packages. Various control laws were investigated for the rear steer angle with the objective of reducing the sideslip angle. A full 3D model of the vehicle incorporating weight transfer and tire non-linearity was then developed using the DADS software. An algorithm developed using the linear model with the aim of reducing vehicle sideslip angle was implemented in the nonlinear model. It is shown that this algorithm can improve the dynamic performance for both …

Energy Reduction By Enhanced Evaporative Cooling Of Buildings In Martime Climates, Ben Costelloe, Donal Finn

Conference Papers

Direct cooling of buildings by water evaporation has traditionally been seen as appropriate, only, in dry and arid climates, which experience high levels of wet bulb temperature depression. The technique has generally not been applied in maritime climates where low levels of wet bulb temperature depression are frequently found. However, recent developments in enhancing heat and mass transfer in cooling towers, together with the success of high temperature sensible cooling systems, such as chilled ceiling panels and beams, have prompted a review of the evaporative cooling technique as an effective and low energy means of cooling modern deep plan buildings, …

Exergetic Cost Analysis Of A Mechanical Exergy Recycle, Jim Mcgovern

Conference Papers

A mechanical plant that involves an exergy recycle is presented for analysis. It consists of gearboxes and a fluid coupling. There is one input of shaft power to the plant and there are three separate outputs of shaft power. An exergetic cost analysis approach is outlined and applied to the plant.

A Virtual-System Concept For Exergy Analysis Of Flow Network Plant; Part I: Principles, Jim Mcgovern, Francis O'Toole

Conference Papers

A new type of virtual system, named a flow constraint system (FCS), is proposed to facilitate, clarify, and simplify exergy analyses of plant that involve material flow networks. The need for the virtual system is outlined and the concept is demonstrated by applying it to a CHP steam cycle. The FCS concept allows the physical constraints on the exergy interactions associated with flow streams to be taken into account fully. It also simplifies the treatment of bifurcations in material flows and considerably reduces the need for absolute exergy evaluations. The new concept follows from the work already published by the …

A Virtual-System Concept For Exergy Analysis Of Flow Network Plant; Part Ii: Exergetic And Exergonomic Analysis Illustration, Jim Mcgovern, Francis O'Toole

Conference Papers

This paper is a continuation of Part I — Principles, to which it refers extensively. The virtual system concept and the methodology introduced in Part I are illustrated by means of a numerical example. This is an exergetic and exergoeconomic analysis of the CHP steam plant that was described in Part I without operating values and parameters. Matrix methods developed by Valero et al. (1986) are adapted to the new concept. It is shown that these methods are made simpler and less subjective. Bond-graph-type diagrams for exergetic and economic costs are presented.

Heat Pump Research Programme At University College Dublin (1976), Seamus Timoney, Jim Mcgovern

Conference Papers

This paper describes heat pump research at University College Dublin in 1976 relating to an air-to-air heat pump. The plant under test and its instrumentation are described and some measured performance data are presented. A heat pump simulation program is described. A theoretical comparison of refrigerants 12, 22 and 502 is presented with graphs of performance parameters as a function of operating conditions.