Engineering Commons^™

Spatiotemporal Analysis Of Taxi And Transportation Network Companies (Tnc) Demand In The Wake Of Covid-19, Dewan Ashraful Parvez

Electronic Theses and Dissertations, 2020-2023

The objective of the thesis is to understand the factors affecting spatiotemporal ridehailing demand patterns as the COVID-19 pandemic has evolved. Specifically, the current study examines the key contributing factors of weekly ridehailing demand by employing Taxi and Transportation Network Companies (TNC) trip data from January 2019 through December 2020 for New York City. The ridehailing demand is partitioned across four time periods including Morning Peak, Morning Off Peak, Evening Peak and Evening Off Peak to accommodate for the time-of-day specific variations. Drawing on the high-resolution NYC data, the current study developed pooled spatial panel models to accommodate for the …

North 14th Street Corridor Improvements Project, Ashley Nguyen, Samantha Corey, Maricela Paramo Reyes, Pooja Rajeev

Honors Program: Senior Projects (Public)

The following project report was a study of the North 14^th Street corridor ranging from Adams Street to Virginia Street conducted by University of Nebraska-Lincoln students for a senior design capstone project. Main focuses of the project were the intersection of Adams and 14^th Street and the 14^th Street bridges over Cornhusker Highway and Oak Creek. Study of this area included work in transportation, traffic, structural, geotechnical, water resources, and environmental engineering. However, this report done by students should not take the place of work done by licensed professional engineers.

This project was done in collaboration with …

Comparative Analysis Of Bridge Abutment Types, David Fell

Williams Honors College, Honors Research Projects

This project was developed to serve as a brief overview of design practices and considerations in the selection of highway bridge abutment types. This involved a review of literature in the form of reviewing national design guides and department of transportation (DOT) requirements from both US DOTs and international DOTs. The abutment types covered in this research included conventional reinforced concrete abutments with bearings, integral abutments, and semi-integral abutments. This research focused solely on highway bridge abutments, particularly on Ohio Department of Transportation design requirements due to their extensive use of semi-integral abutments. Superstructure elements and geometric requirements are primary …

Investigation Of Casting Methods Of Photoelastic Particles To Study The Geomechanics Of Granular Media, Daniel Schullek

Williams Honors College, Honors Research Projects

The research being conducted within this project is to observe force chains in different samples of soil media with varying shapes. The method for observing the force chains is a process called photoelasticity. Photoelasticity uses two polarizing sheets, with the clear media being tested placed between, and light is directed through the sheets to observe how the light is refracted as force is applied to the tested media. Through our research, we are coming up with a method of casting soil particles through the utilization of resin, silicone, and 3D printing. Once the clear particles have been cast, we will …

Investigating The Mechanical Properties Of Frozen Soil Using Non-Destructive Seismic Wave Measurements, Sean Mach

Williams Honors College, Honors Research Projects

This proposed project will be dealing with investigating the mechanical properties of soil under frozen conditions. This will be done by an innovative non-destructive technology measuring the propagation of seismic waves through the frozen soils from multiple piezoelectric sensors. For the duration of this research, a freezing cell must be constructed to carry out the experimental testing. Multiple levels of saturation will be tested under the given freezing conditions. This should highlight the effect that the level of saturation will have on the propagation of seismic waves throughout the soil. Piezo-electric sensors will be placed in each layer of soil …

Geotextile Design And Performance For Dewatering Of Rare Earth Element Sludge Produced From Acid Mine Drainage, Cory J. Nasiadka

Graduate Theses, Dissertations, and Problem Reports (ETD)

Acid Mine Drainage (AMD) is an environmental legacy of mining operations that forms when sulfide minerals within the earth are exposed to water and oxygen and has significant harmful effects on the environment when left untreated. Researchers at West Virginia University found large concentrations of REE/CMs (Rare Earth Elements and Critical Minerals) in AMD treatment sludge. REE/CM consist of a group of 17 elements that are crucial to the production of advanced technologies. Due to an extremely low domestic supply of REE/CM in the United States, domestic sources and production of REE/CM are being investigated. This research investigates geotextile design …

Crystalline Analysis Of Geomicrobially-Induced Calcium Carbonate Precipitation In Sands Using A Surface Percolation Treatment Technique, Justin Edward Mulloney

UNF Graduate Theses and Dissertations

Ottawa 50/70 sand specimens and natural beach sand samples were treated using bio-augmented geomicrobies via a surface percolation technique. Testing was conducted on these specimens to determine how resultant calcium carbonate precipitation changed as a function of temperature, depth from the surface, and in the presence of magnesium. Specifically, x-ray Diffraction (XRD), a Scanning Electron Microscope (SEM), and Energy Dispersive X-ray Spectroscopy (EDS) were used to determine and quantify the presence of calcium carbonate and its associated phase. Results showed a direct relationship between temperature and precipitated calcium carbonate. In addition, as an unintended consequence associated with the treatment, ammonium …

Additive Manufacturing Of Soil Using Bio-Cementation, Christina Childress

Graduate Theses and Dissertations

Microbially Induced Calcite Precipitation (MICP) is an emerging soil treatment technique that is proven to increase strength, decrease erosion, reduce liquefaction risk, enhance slope stability, decrease compressibility, decrease swelling potential, and overall create a more competent soil. The benefits and applications of MICP are broad, and this research seeks to broaden them further by developing a single-phase additive manufacturing application with no treatment time delay. This is done by analyzing layering behaviors of five USCS soil classifications (100 % Ottawa sand, sand clay mixtures, and 100% lean clay) which provides insight into process variables such as the solution volume and …

Identification Of Phosphorous Loading Point Source Facilities To 303(D) Listed Nutrient Impaired Waters Through Watershed Delineation Using Arcgis For Life Cycle Assessment Applications, John Zimmerman

Chemical Engineering Undergraduate Honors Theses

The work done for this project is part of a larger “life cycle assessment (LCA) of novel electrochemical phosphorus recovery technology at the wastewater treatment plant and U.S. watershed scales” (Morrissey 2019). The goal of that LCA is to determine “environmental impacts of implementing electrochemical struvite recovery at the wastewater treatment plant, U.S watershed, and global scales” (Morrissey 2019). This project’s goal is to identify locations deemed more sensitive to eutrophication impacts. The results will be used as part of the life cycle inventory (LCI) accounting for geographically explicit phosphorus flows. The waters identified as impaired were sourced from the …

Measuring Foundation Course Modulus Using Falling Weight Deflectometer, Light Weight Deflectometer, And Dynamic Cone Penetration, Bruce Barrett, Kellie Troxel, Brady Dresselhaus, David Hansen

Nebraska Department of Transportation: Research Reports

The purpose of this investigation was to determine the feasibility of measuring bituminous foundation course modulus under concrete roadways by comparing testing results derived before and after paving using FWD, Light Weight Deflectometer (LWD), and Dynamic Cone Penetrometer (DCP). The foundation course modulus was determined using FWD data and Darwin design software (‘93 AASHTO). Results from Phase I data collection, which occurred prior to pavement placement, provided a baseline for comparison. The maximum modulus was 398,000 PSI and the minimum was 85,000 PSI, yielding a range of 315,000 PSI and an average modulus of 123,000 PSI over the length of …

Analyzing The Non-Isothermal Multiphasic Flow In Porous Media Through Strongly Coupled Thermo-Hydro-Mechanical Modeling., Mohammadreza Mir Tamizdoust

Electronic Theses and Dissertations

Underground geo-structures and climate change can trigger coupled heat, moisture, and vapor flow in shallow and deep subsurface which is frequently referred to as non-isothermal multiphase flow. The coupled multiphasic flow in soil may induce volumetric shrinkage or expansion deformation depending on the thermo-hydraulic loading condition. In saturated porous media, temperature gradient and heat transfer may affect pore fluid pressure and/or pore fluid flow depending on thermal, mechanical, and hydraulic properties of the media and the saturating fluid. In vadose zones, the prediction of coupled nonisothermal multiphase flow in porous media has been the subject of many theoretical and experimental …

Classification Des Sols Et Sélection Des Systèmes D’Étançonnement Pour L’Excavation Des Tranchées, Bertrand Galy, Denis Lebœuf, Omar Chaallal, André Lan

Rapports de recherche scientifique

Les travaux de fouilles en tranchée exposent les travailleurs à de nombreux risques. L’éboulement est le risque le plus grave et le plus fréquent présent pendant ces travaux, mais hélas, il est très souvent sous-estimé, alors qu’un éboulement mineur de moins d’un mètre cube de terre peut blesser mortellement un travailleur. Une analyse de 50 rapports d’accidents graves et mortels de la Commission des normes, de l’équité, de la santé et de la sécurité du travail (CNESST), survenus entre mai 1974 et juin 2017 lors de travaux d’excavation et de fouilles en tranchées, montre qu’il y a eu 48 décès …

Cyber Physical Systems For Non-Contact Infrastructure Monitoring, Roya Nasimi

Civil Engineering ETDs

In recent decades, the decay of infrastructure has become a relevant challenge of both developed and under developing countries. Prioritization of maintenance and repairs of transportation infrastructure is a new worldwide priority since it is important to quantify the rate of decay of assets to increase both safety and cost-efficient operations. Infrastructure owners need frequent inspections on their assets to predict and to avoid unsafe conditions prone to cause disasters. Frequent infrastructure inspections call for cost-effective methods. Traditional measurement methods require human access to the infrastructure, are subjective, expensive, and unsafe. Therefore, infrastructure managers are interested in exploring new non-contact …

Gap Study For The Impact Of Braced Deep Excavation On The Behavior Of Excavation Bed, Abdelrahman E. Aboelela, Ahmed M. Ebid, Ayman L. Fayed

Future Engineering Journal

Two geotechnical topics were investigated in this research; shored deep excavation and modulus of subgrade reaction. Both topics were extensively studied by many earlier researchers. The aim of this study is to answer the following question, "Is deep excavation effects on excavation bed behavior of sufficiently investigated? Or there still un-studied gaps should be fulfilled?”. Litterateurs were collected, reviewed and classified for both topics especially in the interaction zone between the two topics, and it is concluded that deep excavation effect on the modulus of subgrade reaction values and distribution at excavation bed level is not sufficiently addressed especially the …

Investigation Of Sand-Biochar Mixtures As A Potential Roadway Fill Material, Katia J. Lele Lagmago

LSU Master's Theses

Biochar is a sustainable and lightweight carbon-rich material with a high surface area and porosity. Previous studies reported that biochar can reduce soil erosion and cracking, retain contaminants, and enhance soil aggregation. Given these favorable properties, soil-biochar mixtures have the possibility to serve as a multifunctional lightweight fill material for roadway embankment applications. The purpose of this research is to develop sand-biochar mixtures as a sustainable and multifunctional lightweight fill material for roadway embankment applications.

This research investigated the consolidation and hydraulic properties of sand-biochar mixtures by (1) performing 1D consolidation tests, (2) performing permeability tests, and (3) assessing the …

Undrained Cyclic Loading Of Low Plasticity Silty Soils In The Pacific Northwest Using Laboratory And Field Cyclic Shear Testing, Angelica Melissa Preciado Reyes

Dissertations and Theses

The cyclic behavior of a fine-grained low plasticity silty soil (plasticity index of approximately 15) at a site in Portland, Oregon, is characterized using a field and laboratory cyclic shear test program. The field cyclic tests were performed using the NHERI@UTexas large mobile shakers T-Rex and Rattler. The laboratory tests were performed using resonant column torsional shear and cyclic direct simple shear devices. This testing program's results were used to evaluate the soil's potential to develop excess pore water pressure with cyclic shear strains ranging from 0.00001% to 3%. The laboratory cyclic test results are compared against field cyclic test …

Development Of A New Electro-Osmotic Consolidation Apparatus, Yenni Mariana Ramírez-Mazo, Juan Pablo Osorio, Sergio Agudelo

Conference papers

Electro-osmotic consolidation is a ground improvement technique in which a DC voltage is applied to the soil via electrodes, in order to drain the water contained in the pores increasing the effective stress, and thus improving the geotechnical properties of the soil. The technique increases the shear strength, reduces the compressibility, and changes the chemical composition of the saturated soft clayey and silty soils to which it can be applied. Electro-osmotic consolidation has been successfully applied in different projects worldwide. This paper presents the development of a new electro-osmotic consolidation apparatus built at Universidad de Antioquia. Tests were carried on …

Geological Origin As An Input Variable In Reliability-Based Designs: For An Accurate Exploration In Geotechnical Engineering, Juan Camilo Viviescas, Juan Pablo Osorio

Conference papers

Soil is one of the most difficult materials to characterize realistically, which partly explains the uncertainty between the designs and the geostructures real behavior. Different recommendations have arisen with respect to carrying out field investigations in order to reduce the uncertainties inherent to the soil. However, the field exploration and the implementation of sophisticated geotechnical models have proven to be insufficient to mitigate the geotechnical uncertainty. Therefore, Reliability-Based Designs (RBD) emerge as a decision-making tool through the definition of the probability of failure in conjunction with the typical Factors of Safety. RBD requires a previous understanding of the most appropriate …

An Exploration Of Lean And Bim Synergies With A Focus On Smes In Construction, Barry Mcauley, Marina Andreou, Alan V. Hore, Avril Behan

Conference papers

Small and Medium Enterprises (SME) account for 99.7% of the Irish Construction Industry and contribute to 68% of all employment in the sector. These organisations now find themselves facing the challenge of returning to productive business post the Covid 19 shutdown. More than ever, SMEs must modernise and adapt their business models to embrace new ways of working, such as Lean Construction and Building Information Modelling (BIM), in the absence of clear business incentives. It has proved difficult to persuade SMEs to change their ways of working due to limited finances, internal resources and above all, the cultural shift required …

Flow Behavior Of Granular Soil And Impounded Fly Ash Slurries, Nuzhath Fatema

Dissertations - ALL

Failure of an embankment dam around mine tailings and coal ash slurry impoundments typically results in a fast-moving flow of toxic waste that can carry for several miles with disastrous consequence. The most recent catastrophic tailing-dam failure took place on 25 January 2019, at Brumadinho, Brazil, where the resultant tailings flow killed at least 232 people. A similar impoundment failure also occurred in 2008 at the TVA Kingston fossil power plant in Tennessee, USA, where coal combustion residuals such as fly ash and bottom ash were stored in the impoundments. The catastrophic failure at Kingston released 4.2 million m3 of …

Develop A Multi-Functional Green Pervious Concrete (Mgpc) Pavement With Polycyclic Aromatic Hydrocarbons (Pahs) Removal Function., Hong Shang

Electronic Theses and Dissertations

Stormwater runoff induced Polycyclic Aromatic Hydrocarbons (PAHs) contaminant increasingly imperils the groundwater quality and the sustainable development of human society due to the potential carcinogenic risks. Pavement can be considered as the first line of defense for contaminant removal of the stormwater runoff. New construction materials with stormwater runoff quantity and quality control are in urgent demand for updating the existing pavement system. An innovative material called Multi-functional Green Pervious Concrete (MGPC) was developed in the department of Civil and Environmental Engineering at University of Louisville. This material uses organoclay as the amendment to enhance the PAHs removal capacity of …

Prediction Of Uniaxial Compressive Strength Of Granite Rock Samples Of Lugoba Quarry Using Rebound Hammer Test, Moses Kongola, Karim Baruti

Tanzania Journal of Engineering and Technology (TJET)

Rebound hammer test is widely used as an indirect measure of uniaxial compressive strength for engineering materials such as concrete, soil, and rock in both civil and mining engineering works. In quarries, uniaxial compressive strength is a crucial parameter in the analysis of geotechnical problems involving rock stability and rock blasting design. This study aims at establishing the empirical models of uniaxial compressive strength fits on rebound hammer number that can be used to predict uniaxial compressive strength of granitic rock at Lugoba Quarry. Data for direct uniaxial compressive strength were obtained from uniaxial compressive strength test carried out on …

Finite Element Numerical Modeling And Parametric Study Of Geosynthetic Reinforced Pile-Supported Embankments, Abdallah Ikbarieh

LSU Master's Theses

This study directed at investigating the performance of the pile-supported embankment system utilizing a geosynthetic reinforced load transfer platform (GRLTP) using Finite Element numerical modeling. A 2D Finite Element Modeling (FEM) methodology was first developed using PLAXIS 2D 2021 computer software and verified by well-documented case studies in the literature of this system. Second, a performance prediction was made for a field case study of the Amite River Project near French Settlement, which is located along Route LA 16 Livingston Parish in Louisiana State. A comprehensive FEM parametric study was then carried out to evaluate the performance of the system …

Probabilistic Analysis Of The Active Earth Pressure On Earth Retaining Walls For C‑Φ Soils According To The Mazindrani And Ganjali Method, Julian Osorio, Juan Camilo Viviescas, Juan Pablo Osorio

Articles

The determination of the earth pressure coefficients (K) in geotechnical engineering is one of the most critical procedures in designing earth retaining walls. However, most earth pressure theories are made for either clay or sands, where the c-ϕ soils are the least analysed. In this paper, an analysis of the earth pressure for drained mixed soils based in Mazindrani and Ganjali (J Geotech Geoenviron Eng 123:110–112, 1997) theory was carried out. Earth pressure coefficients are generally used in a deterministic way and can represent designs under an inadmissible risk. Therefore, Reliability-based design arises as an essential tool to deal with …

Review Of Expansive And Collapsible Soil Volume Change Models Within A Unified Elastoplastic Framework, Sandra L. Houston, Xiong Zhang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Numerous laboratory tests on unsaturated soils revealed complex volume-change response to reduction of soil suction, resulting in early development of state surface approaches that incorporate soil expansion or collapse due to wetting under load. Nonetheless, expansive and collapsible soils are often viewed separately in research and practice, resulting in development of numerous constitutive models specific to the direction of volume change resulting from suction decrease. In addition, several elastoplastic models, developed primarily for collapse or expansion, are modified by add-on, such as multiple yield curves/ surfaces, to accommodate a broader range of soil response. Current tendency to think of unsaturated …

Applications Of Masw And Mhvsr Techniques For Infrastructure Evaluation With A Focus On The Effects Of Different Transformation Techniques And Near-Field Effects On Derived Dispersion Data, Salman Rahimi

Graduate Theses and Dissertations

This dissertation is aimed at understanding two aspects of active surface wave methods to improve the accuracy and reliability of this method. These include (1) the performance of four common wavefield transformation methods for the multichannel analysis of surface wave (MASW) data processing and (2) near-field effects. Toward this end, extensive field measurements were conducted considering different factors affecting these two topics. The MASW and microtremor horizontal to vertical spectral ratio (MHVSR) were then employed to examine their efficiency for infrastructure health monitoring.

Regarding the performance of the four common transformation techniques, it was observed that for sites with a …

Erratum: Characterizing Permanent Deformation Of Alaskan Granular Base-Course Materials (Journal Of Materials In Civil Engineering Doi: 10.1061/(Asce)Mt.1943-5533.0002911), Jenny Liu, Xiong Zhang, Lin Li, Peng Li, Steve Saboundjian

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The writers would like to express their appreciation to the discusser for taking time to read this paper and provide his insightful viewpoint. The writers are in general agreement with the discusser's comments and this closure allows them to further clarify some of the statements in the original paper. Frost Heave and Change of Moisture Conditions after a Freezing Process The writers appreciate the discusser's further explanation and elaboration of results presented in Table 1 and Figs. 5 and 8. Permanent Deformation Modeling The writers agree with the discusser that the R2 values of Eqs. (2) – (4) in the …

Dynamic Soil-Structure Interaction Analysis: Detecting The Reliability Of Modelling The Piles As A Plate Element For A Multistory Building Resting On Deep Foundation, Zeinab Hussein Zein Z.H.Zein, Lina Jaber L. Jaber, Yehya Temsah Y. Temsah

BAU Journal - Science and Technology

The assessment of seismic responses of buildings in dynamic-soil-pile-structure interaction problems has been one of the main interests among researchers in recent decades. Simulating such problems is usually done by two-dimensional models to overcome the difficulties encountered in 3D models. Commonly, piles were represented by plate elements of infinite length, disregarding the soil flowing between piles. Recently, Plaxis – a finite element software- implemented a new feature known as “the embedded pile row” that allows the definition of piles' out of plane spacing in a 2D model. Many researchers proved its validity in accurately simulating the real 3D pile’s behavior. …

Characterization Of Landslide Processes From Radar Remote Sensing And Hydromechanical Modeling, Yuankun Xu

Earth Sciences Theses and Dissertations

Landsides are a natural geomorphic process yet a dangerous hazard which annually causes thousands of casualties and billions of property loss in a global scale. Understanding landslide motion kinematics from early initiation to final deposition is critical for monitoring, assessing, and forecasting landslide movement in order to mitigate their hazards. Landslides occur under diverse environmental settings and appear in variable types; however, all types of landslides can be mechanically attributed to shearing failure at the basal surface due to stress regime shift contributed by internal and/or external forcing. Typical internal factors include soil/rock weathering, whereas typical external triggering forces encompass …

Examination Of The Correlation Between Shear Strength, California Bearing Ratio, And Index Properties Of Fine-Grained Soil, Billy W. Rushema

Master of Science in Civil Engineering Theses

Abstract

California Bering Ratio (CBR) is used to evaluate the strength of the pavement materials by comparing bearing capacity of the material with that of a high-quality crushed stone. This test adopted by transportation agencies and widely used in the design and analysis of pavement. Several agencies developed design thickness chart based on the CBR values of the subgrade. However, CBR test is time consuming and expensive to perform compared to shear strength test and therefore several studies have been conducted to establish correlation between shear strength and CBR. The published correlation models between CBR and shear strength of soil …