Engineering Commons^™

Towing Tank Trials Of Hydrokinetic Turbine Scale Model To Support Marine Energy System Verification, Shahab Rouhi

LSU New Orleans Theses and Dissertations

In response to the escalating demand for sustainable energy solutions and the critical reevaluation of conventional fossil fuels due to environmental concerns, this dissertation embarks on a comprehensive exploration of hydrokinetic energy as a promising alternative. The study delves into the underexplored domain of hydrokinetic energy, leveraging innovative methodologies for effective utilization and harnessing, particularly through the development and investigation of hydrokinetic turbines.

In the realm of hydrokinetic energy conversion, our research has exclusively concentrated on horizontal-axis turbines, distinct from other turbine configurations. Noteworthy is the adaptation of a conventional horizontal-axis wind turbine for water currents, revealing enhanced performance through …

Cal Poly Fluid Power Vehicle Challenge 2024, J. Mason Gray, Ryan D'Amour, Alberto Acho Lopez, Christian Ferrandino, Johnathan Dietz

Mechanical Engineering

In this Final Design Review, the Cal Poly Fluid Power Vehicle Team competed in Norgren’s 2024 Fluid Power Vehicle Challenge. The design need of the competition was for college teams to compete with human-powered, hydraulic-driven vehicles in an endurance race, a sprint race, an efficiency race, and a regenerative power race. The competition need was to design a vehicle to win in as many races as possible, achieving the highest overall score and winning the competition. With a design emphasis on the endurance and sprint race, the Cal Poly team designed a fluid power system that fastened to a purchased …

Barocaloric Heat Pumps Based On Soft Materials., Naveen Weerasekera

Electronic Theses and Dissertations

Solid-state refrigeration offers a promising alternative to traditional vapor compression systems that are relatively inefficient, unreliable, and have a high global warming potential. Various solid-state cooling technologies, including those based on electrocaloric, magnetocaloric, and elastocaloric effects have been investigated in the recent past. However, concerns regarding their efficiency, scalability and cost remain. Refrigeration and heat pump technologies based on the barocaloric effect (temperature/entropy change due to hydrostatic pressure) hold great promise but have received comparatively less attention. Barocaloric heating/cooling based on low cost, compressible soft materials with large barocaloric response have the potential to pave the way for efficient, scalable, …

Synthesis Of Durable Zeolite 13x Insertion Coatings And Scaled-Up Experimental Demonstration For Co2 Capture, Daniel Jamil Hocheimy

Theses and Dissertations

Minimizing the energy requirement for capturing carbon dioxide (CO₂) from post-combustion sources is critical to efficient industrial decarbonization and subsequent mitigation of the effects of climate change. The current portfolio of CO₂ capture technologies includes absorption, membrane separation and packed bed adsorption, which suffer from high energy and temperature requirements, scalability, and location dependency issues. Adsorption-based systems could cater to these concerns; however, their current embodiments primarily use packed adsorbent bed design and electricity-driven vacuum pumps to regenerate them. While simple and easy to fabricate, these designs are not scalable and cannot use heat to regenerate them …

Dynamic Impact Testing And Numerical Analysis Of Non-Proprietary Astm F2656-20 M50 Anti-Ram Barrier Components, Weston Kelley

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

In a post-9/11 world, hostile actors are using vehicles as weapons to inflict civilian casualties. Pedestrians, vulnerable road users, military personnel, and police may be targeted using a vehicle as a weapon. The United States Department of Defense (DoD) also utilizes Entry Control Facilities (ECFs) which are carefully designed transportation corridors to manage how threat vehicles are able to access military facilities. In 2004, DoD started to upgrade all ECFs using both passive and active barriers. Many anti-ram vehicle barriers were evaluated according to the criteria established in ASTM F2656, but to date few options are available which are (1) …

Renewable Energy Misinformation: A Literature Based Approach To Rebutting False Claims, Matthew Ard

McNair Research Journal SJSU

No abstract provided.

Optimization Pump As Turbine Coupled To A Self-Excited Induction Generator Using Multi-Objective Genetic Algorithm, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

As a way of accelerating the deployment of affordable and clean renewable energy generation technologies, applying a pump working as a turbine coupled to a self-excited induction generator is gaining popularity in various areas including energy recovery and micro hydro systems. However, it is currently challenging to predict the performance of the PAT-SEIG system and there is no agreed-upon rule on the selection of the appropriate system to be installed at a particular site. This paper has presented multi-objective optimization to select the best operating point of the PAT-SEIG system. The results show that the peak efficiencies for the PAT …

Optimal Load Shedding During Service Restoration In Electrical Secondary Distribution Network Based On Reinforcement Learning, Rukia J. Mwifunyi

Tanzania Journal of Engineering and Technology (TJET)

Increased stress in traditional power systems results in blackouts due to voltage instability attributed to a mismatch between available capacity and load demand, especially in distribution networks. Service restoration schemes are designed to return power supply to the affected parts of the networks. The availability of insufficient supply is a complex problem that requires operational experience or an automatic system. The stochastic nature of load demand significantly impacts service restoration as it results in increased restored demand in case a fault occurs during off-peak hours and helps reduce overload if the fault occurs during peak hours. The study adopts an …

Comparison Of Meteorological Drought Indices In Tanzania Using The Meteorological Drought Monitoring Software Package, Paul Ts Limbu

Tanzania Journal of Engineering and Technology (TJET)

Low precipitation, substantial evaporation, and an unequal distribution of precipitation throughout the area are the characteristics of drought, a climatic abnormality. This study used the Meteorological Drought Monitoring (MDM) software and monthly rainfall data from the Tanzania Meteorological Authority (TMA) to examine and compare the Deciles Index (DI), Standardised Precipitation Index (SPI), Percent of Normal Index (PNI), Rainfall Anomaly Index (RAI), Z-Score Index (ZSI), China-Z Index (CZI), and Modified China-Z Index (MCZI) for drought monitoring in Tanzania from 1988 to 2017. It was found that ZSI represented the dry years better than other indices, followed by DI, RAI, PNI, SPI, …

An Optimization Tool For A Standalone Photovoltaic System, Johanes Kasilima

Tanzania Journal of Engineering and Technology (TJET)

Stand-alone photovoltaic systems (SAPV) are often used in remote areas where access to grid electricity is limited. This system depends on solar energy. However, Photovoltaic (PV) systems need a greater initial investment than conventional sources of energy, and their effectiveness is reliant on a number of environmental conditions such as the unpredictable solar radiation. One step in reducing the investment cost of a PV system is determining the optimal size of solar PV components that minimize costs. This paper presents a Particle Swarm based optimization tool for sizing Stand-alone PV systems. The optimization tool selects the optimal Levelized Cost of …

Guidelines For Data Collection On Energy Performance Of Higher-Education Buildings In Egypt: A Case Study, Hesham Safwat, Ahmed A. Abdel-Rehim, Iman El-Mahallawi, Abdelwahab Hussein, Engy Elshazly, Ahmad Elshamy

Mechanical Engineering

Reliable energy analysis of buildings relies heavily on high-quality data leading to proper indicators. Previous studies have highlighted the importance of data quality in analyzing energy usage in residential and non-residential buildings in order to transform declarations to actions, optimise energy efficiency policies and monitor progress and failures in countries. Collected data must adhere to national and international standards for energy performance in buildings. This study aims to provide practical guidelines for effectively collecting and preparing data suitable for evaluating energy performance in Egyptian higher-education (HE) buildings. The guidelines are developed based on a comprehensive case study, considering data availability …

Radiative Cooling For Energy-Efficient Power Generation, Rickia Hanna

Celebrating Scholarship and Creativity Day (2018-)

This thesis examined radiative cooling on a small scale using a hybrid photovoltaic/radiative cooling model system, to determine its efficiency for large-scale power generation. Radiative cooling is concerned with heat transfer and this thesis’s main goal is to harness that heat energy to produce electricity. The efficiency of the system was tested using various light sources at different angles and total power output. The testing was done several times and there proved to be a proportional relationship between light intensity and current output. However, due to the performance threshold of the PTEC module, the component of the system used to …

Offshore Wind Farm Pycnocline Mixing From Varied Flow Types, Laura Lundahl

Student Research Symposium

As the demand for sustainable low carbon energy grows, offshore wind farms (OWFs) are becoming increasingly popular and are being pushed into stratified regions where a pycnocline exists (Figure 1). These wind farms may cause turbulent mixing of the pycnocline, which will harm the phytoplankton ecosystem. This project quantifies pycnocline mixing to gain knowledge of effective methods for mitigating harmful effects.

Design And Simulation Of Flow Channel Of Polymer Electrolyte Membrane Fuel Cell (Pemfc), Rishya Shringhan Ravichandran

Masters Theses

In Polymer Electrolyte Membrane Fuel Cell (PEMFC), flow channel plays an important role on the performance of the cell. This study mainly focuses on the simulation of flow channel under various conditions. A three-dimensional mode of PEMFC with 25cm² of active area was employed to simulate the flow channel of PEMFC which has various designs. The flow channel designs such as single serpentine, bi-serpentine and tri-serpentine channels were investigated using ANSYS FLUENT software. Initially, the flow channel width of 2mm was examined. The obtained results were compared to the experimental data to validate the model. Then, the dimension of …

Benchmarking Of A Sco2 Heat Exchanger Flow Loop, David Velasco

Doctoral Dissertations and Master's Theses

Heat transfer of supercritical carbon dioxide (sCO2) was studied experimentally by commissioning a sCO2 flow loop featuring a horizontal tube-in-tube counterflow heat exchanger with a circular cross section. The main objective was to establish experimental heat transfer research capabilities for sCO2 at Embry-Riddle Aeronautical University’s (ERAU) Thermal Science Lab. sCO2 experiences a drastic change in thermophysical properties near its critical point that results in unique heat transfer characteristics. The high pressures at which sCO2 exists make the large gradients in thermophysical and transport properties difficult to study, experimentally and numerically. However, understanding the heat transfer characteristics and thermophysical behavior of …

Performance Augmentation Of Single-Slope Solar Distiller Using An Evacuated Tube Solar Collector: Theoretical Study, Eman Mohammed Abuelezz Eng., Yasser El-Samadony Prof., Khaled Khodary Esmaeil Assoc. Prof., Mohamed Elsheshtawy Zayed Dr.

Journal of Engineering Research

In this research, the performance analysis of a solar-powered desalination system incorporating a single slope-slope solar still and an evacuated tube solar collector is theoretically investigated. The system comprises a solar evacuated tube that absorbs solar radiation, transferring heat to saline water. This water then flows into a solar still, where it absorbs solar energy, boosting the evaporation rate. Two solar distillers, namely the conventional solar distiller (Still-I) and solar still integrated with evacuated tube solar collector (Still-II), are simulated and analyzed under identical outdoor conditions in Tanta, Egypt. A comprehensive theoretical model, developed using FORTAN programming, simulates the performance …

Numerical Analysis Of Flow Fields For The Different Models Of The Shrouded Savonius Rotor, Alsaied Khalil Mahmoud, Mohamed Mahgoub Bassuoni, Mohamed Fawzy Obiaa, Ahmed Mostafa Khaira

Journal of Engineering Research

In this study, the effect of three different lengths (short, medium, and long) of flanged shrouded Savonius wind turbines is investigated three-dimensional (3-D) numerically by ANSYS-FLUENT. The 3-D numerical model of a simple rotor is validated by comparing the results with previous published experimental ones at the same operating conditions and geometry. The numerical and experimental results indicate a good agreement with each other when using the SST K-ω model with a time step size of 0.0025 s.The analysis of the numerical results of the three flanged shrouded models shows an enhancement of the torque coefficient at tip speed ratio …

Quantum-Powered Battery Scheduling In Modern Distribution Grids, Diba Ehsani

Electronic Theses and Dissertations

The rising need for exploiting a novel and evolved computation is an increasing concern in the power distribution system to address the exponential growth of distribution-connected devices. Scheduling numerous battery energy storage systems in an optimal way is one of the emerging challenges that will be more noticeable as the number of batteries, including residential, community, and vehicle batteries, increases in the grid. This thesis focuses on this topic and offers a necessary component in building the quantum-compatible distribution system of the future. Using a constrained quadratic model (CQM) on D-Wave’s hybrid solver as well as a binary quadratic model …

Cost Estimation Proxy Models For Economic Evaluations In Petroleum Projects: A Case Study From The Onshore Gas Field In The Southern Coastal Tanzania Basin, Fulmence Kaborogo

Tanzania Journal of Engineering and Technology (TJET)

Petroleum economic evaluation involves estimating revenues from forecasted production profiles and field costs including capital expenditures (CAPEX), drilling expenses (DRILLEX), and operating expenses (OPEX). The existing cost-estimating tool requires several inputs making it time-intensive and difficult to use with few data during the early stages of projects. Majority of the previously developed time saving cost estimations proxy models rely on unrealistic assumptions that include uniform operational costs for different fields with a different number of wells, casings, and drilled depths. This work focused at developing proxy models that consider the variability of the development costs with different parameters. The developed …

Enhancing The Performance Of Conventional Solar Still Using The Nano-Doped Paint (Ndp) Coating, Hagar Alm-Eldin Bastawissi Prof.Dr, Nermin Elgendy Engineer, Ayman R. El-Tohamy

Journal of Engineering Research

Nations are throughout the entire globe continuously confronting the problem of potable water shortage. Recently, it has been thought that using solar energy to desalinate brackish water offers a practical answer to the world's water crises. The output of these stills, is meager, and academics haven't done much to boost it in any way. Solar distillers have been proposed as an efficient method to produce potable water. In recent years, saltwater has produced drinking water by various ways. The efficiency of a solar distiller is significantly influenced by various factors, most important factor of them is the absorber surface. In …

Numerical Study Of The Effect Of Long Shroud Diffuser With And Without Plate Obstacle On The Performance Of Savonius Wind Turbine, Alsaied Khalil Mahmoud, Mohamed Mahgoub Bassuoni, Mohamed Fawzy Obiaa, Ahmed Mostafa Khaira

Journal of Engineering Research

This study presents the three-dimensional (3-D) numerical analysis of the influence of the plate obstacle installed at the entrance of the long flanged diffuser on the simple Savonius rotor performance by ANSYS 2022 R1. In the beginning, the 3-D numerical model is validated using the sst k-ω turbulence model with the previous published experimental results at the same conditions, and they are in good agreement with each other. The numerical results indicate the remarkable enhancement of the rotor performance at a tip speed ratio of 0 to 0.7 by using a flanged diffuser with a plate obstacle. The shrouded diffuser …

Tractor Test 2282: John Deere 9rt 590 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Process Simulation For Converting Co2 Emissions From The Cementindustry To Dimethyl Ether, Nour Abou Seada, Dina Aboelela

Biochemical Engineering

Climate change is the leading severe problem in the twenty-first century, which is associated with greenhouse gas emissions,carbon dioxide that is the foremost cause of global warming and super greenhouse effect. In this concern, to avoid hazardousproblems, the steady stream of CO2 effluents existing in the atmosphere must be transformed to beneficial products for beingused as an abundant chemical feedstock. Implementing a new green strategy, which is known for the catalytic hydrogenationof CO2 into alternative fuels and valuable chemicals, will be a long-lasting solution to alleviate CO2 emissions. In this paper,a process simulation showing the synthesis of dimethyl ether (DME) …

Hydrogen Production From Microbial Electrolysis Cells Powered With Microbial Fuel Cells, Dina Aboelela

Biochemical Engineering

No abstract provided.

Tractor Test # 2283: Claas Axion 920, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1285: Massey Ferguson 8s 205, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Graphene Reinforced Polymer Composite For Small-Scale Vertical Axis Wind Turbine Rotors, Kunal A. Bachim

Mechanical and Aerospace Engineering Theses - Archive

Polymers have evolved as an indispensable asset in various sectors ranging from packaging and construction to energy and aerospace. However, the accumulation of polymer waste poses a necessity to shift toward sustainable waste management processes. Mechanical recycling is a primary method in establishing a circular economy approach for polymers. However, a fundamental challenge arises in this process: a decrease in the mechanical performance of the recycled product compared to that of its pristine counterpart.

This project addresses the challenge of enhancing the recyclability of polyethylene terephthalate (PET) from discarded polymer material by incorporating graphene nanoparticles into the polymer matrix during …

Tractor Test 2280: John Deere 9rt 490 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Tractor Test #2295: Kubota M7-174, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Tractor Test #2293: Kubota M7-134, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …