Engineering Commons^™

Designing A Cylindrical Capacitive Based Sensor For Monitoring The Table Salt’S Moisture Content During Iodization, Mwajuma Lungo

Tanzania Journal of Engineering and Technology (TJET)

Coaxial cylinder capacitive moisture sensor for determination of moisture content of table salts has been fabricated. The CMS method for determination of moisture content of table salts overcomes the effect of evaporation of iodine in table salt which results from heating in the oven drying method. The CMS overcomes the polarization effect result from the resistive methods of moisture content determination and it is non expensive to construct and it has high accuracy since measurements involves programming system in interpretation of the results. In this research, moisture content sensor based on capacitive principal created using two coaxial cylinders with height …

Detection Of Cancer-Associated Gene Mutations In Urinary Cell-Free Dna Among Prostate Cancer Patients In South Africa, Dada Oluwaseyi Temilola, Martha Wium, Juliano Paccez, Azola Samkele Salukazana, Solomon O. Rotimi, Hasan H. Otu, Giuseppina M. Carbone, Lisa Kaestner, Stefano Cacciatore, Luiz Fernando Zerbini

Department of Electrical and Computer Engineering: Faculty Publications

Prostate cancer (PCa) is the most common cause of cancer death among African men. The presence of tumor-specific variations in cell-free DNA (cfDNA), such as mutations, microsatellite instability, and DNA methylation, has been explored as a source of biomarkers for cancer diagnosis. In this study, we investigated the diagnostic role of cfDNA among South African PCa patients. We performed whole exome sequencing (WES) of urinary cfDNA. We identified a novel panel of 31 significantly deregulated somatic mutated genes between PCa and benign prostatic hyperplasia (BPH). Additionally, we performed whole-genome sequencing (WGS) on matching PCa and normal prostate tissue in an …

Comparison Of A Bottom-Up Gnss Radio Occultation Method To Measure D- And E-Region Electron Densities With Ionosondes And Firi, Dylan J. Shaver, Dong L. Wu, Nimalan Swarnalingam, Anthony L. Franz, Eugene V. Dao, Daniel J. Emmons

Faculty Publications

High-frequency skywave propagation can be heavily impacted by D- and E-region dynamics requiring accurate global measurements to optimize performance. A standard measurement technique is to use ionosondes, but they are unable to measure below 1 MHz and are only available at a limited number of land-locked sites around the globe. In contrast, the Global Navigation Satellite System radio occultation (GNSS-RO) bottom-up method is a new approach specifically designed to generate electron density profiles in the D- and E- region ionosphere. It takes advantage of satellite constellations that currently provide over 20,000 daily measurements and global coverage. In this paper, GNSS-RO …

Development Of The Computer Model Of The Waste Water Treatment Process Using Ion-Exchange Resins In The Matlab Program, Jaloliddin Abdurazzakovich Eshbobaev, Bakhodir Tajiddinovich Khamidov, Adham Tilovovich Norkobilov, Orifjon Sharipovich Kodirov

Chemical Technology, Control and Management

In this work, a mathematical model of industrial wastewater treatment technology was formed. First, wastewater treatment technologies were analyzed and the technology of ion-exchange resin treatment was selected. A water purification device using ion-exchange resins was made, and tested on the Kungrad soda plant and the results were obtained. According to these results, it was determined that the cleaning coefficient of the device is up to 98-99%. In this article, a mathematical model of a wastewater treatment device using ion-exchange resins was developed using the stoichiometric matrix method. After the mathematical model of the process was found, a graph of …

A Method For Economic Expansion Planning Of Transmission Networks Using Heuristic Rules And Non-Linear Optimization Model, Maged Gamal Lotfy, Mahmoud Ali Farrag, Mohamed Shibl Albags, Ahmed Hamdy Khalil

Mansoura Engineering Journal

This paper presents a method for economic planning of transmission networks in an iterative manner. The method is capable of solving large scale networks where the most "worst" new lines are deleted iteratively using heuristic rules. In each iteration, a relatively small size non-linear mathematical Programming model is built to enhance the deletion process. The non-linear model is based on full AC load flow where only the reactive power injected from different available reactive power sources are controlled plus the reference bus voltage magnitude. The deletion process is stopped when the deleting of any line from the rest set of …

Exploring The Impact Of Students Demographic Attributes On Performance Prediction Through Binary Classification In The Kdp Model, Issah Iddrisu, Peter Appiahene, Obed Appiah, Inusah Fuseini

Knowledge Engineering and Data Science

During the course of this research, binary classification and the Knowledge Discovery Process (KDP) were used. The experimental and analytical capabilities of Rapid Miner's 9.10.010 instructional environment are supported by five different classifiers. Included in the analysis were 2334 entries, 17 characteristics, and one class variable containing the students' average score for the semester. There were twenty experiments carried out. During the studies, 10-fold cross-validation and ratio split validation, together with bootstrap sampling, were used. It was determined whether or not to use the Random Forest (RF), Rule Induction (RI), Naive Bayes (NB), Logistic Regression (LR), or Deep Learning (DL) …

Neurocomputing And Interfacing Digital Tasting System: Research, Design, And Evaluation, Amira J. Zaylaa, Ahmad El Hajj

BAU Journal - Science and Technology

The continuous evolution in computing and interfacing has been extended to develop multi-sensory experiences in many domains such as neurological, auditory, vision, and haptic domains. So far, only a few remarkable system approaches have been approved to be serving the taste sensation digitally. Although taste sensation is linked to the brain, there is a lack of optimal neurocomputing digital taste sensation systems. Our study provides a new neurocomputing method to digitally stimulate the sense of taste by electrical stimulation on the human tongue. We aim to link chemical stimulation and electrical stimulation in order to design an electronic interface for …

On The Use Of Wireless Technologies For Wildlife Monitoring: Wireless Sensor Network Routing Protocols, Lilian Mutalemwa

Tanzania Journal of Engineering and Technology (TJET)

Traditional methods for wildlife monitoring are labor-intensive and time-consuming. Therefore, advanced technologies and remote monitoring methods are becoming increasingly popular. This paper presents a study on wireless technologies for wildlife monitoring. In the study, a review of the literature was done to identify the most commonly used wireless technologies. Various technologies were explored including unmanned aerial vehicles (UAVs), Internet of Things (IoT), wireless sensor networks (WSNs), artificial intelligence (AI), global positioning system (GPS), and very high frequency (VHF) radio. Then, a more detailed study was done on WSN technology. Investigations were done to observe the performance of routing protocols in …

Work In Progress: Assessing Engineering Students' Behavioral Engagement And Learning; Survey Development And Validation, Ibukun Samuel Osunbunmi, Kurt Henry Becker, Young Min Kim, Mohammad Al Mestiraihi

Electrical and Computer Engineering Faculty Publications

Studies have shown that the more involved students are with their learning, the better their achieved desired educational outcome. However, little is known about the extent to which the existing engineering curriculum and pedagogical strategy implemented elicit engineering students’ engagement in the Middle East and North Africa region (MENA) of the world. The goal of this study is to examine to what extent the existing engineering curriculum elicits student engagement in self-learning and collaborative learning. This effort is part of the ongoing re-evaluation and redesign of the water engineering curriculum of one of the countries in the MENA region by …

Tank Level Controller Plc Lab, Siddhi Upadhyaya, Teghvir Grewal

Electrical Engineering

The California Polytechnic State University San Luis Obispo’s Electrical Engineering Department is currently developing lab experiments for the new EE435 (Industrial Power Control and Automation) class. In order to support these efforts, fourth year Cal Poly students are expected to develop laboratory experiments that will be conducted during this new class for the semester system. The lab experiment focused on in this project is called the Tank Level Controller. This experiment will introduce EE 435 students to Schneider Electric Programmable Logic Controller (PLC) hardware and software, which is prominent in the automation industry.
This experiment will require students to develop …

Development Of Cal Poly’S Hybrid Ac/Dc House, Eduardo Andres Muñoz, Giovanni Ramirez Angel

Electrical Engineering

The Hybrid House provides an example for what sustainable housing solutions could look like. It also functions as a potential solution to the current rural electrification issues many developing countries face. The use of a DC-DC MISO converter allows for combining multiple power sources into a single DC bus. The Hybrid House integrates the DC bus by employing the use of DC-DC converters for home use. This system may potentially improve the overall system efficiency by avoiding the losses associated with AC-DC converters. The use of the DC bus further leverages the Solar Panel renewable energy solution to become a …

Investigation Of Degradation Of Solar Photovoltaics: A Review Of Aging Factors, Impacts, And Future Directions Toward Sustainable Energy Management, Eklas Hossain

Electrical and Computer Engineering Faculty Publications and Presentations

The degradation of solar photovoltaic (PV) modules is caused by a number of factors that have an impact on their effectiveness, performance, and lifetime. One of the reasons contributing to the decline in solar PV performance is the aging issue. This study comprehensively examines the effects and difficulties associated with aging and degradation in solar PV applications. In light of this, this article examines and analyzes many aging factors, including temperature, humidity, dust, discoloration, cracks, and delamination. Additionally, the effects of aging factors on solar PV performance, including the lifetime, efficiency, material degradation, overheating, and mismatching, are critically investigated. Furthermore, …

To Study Heart Rate Dynamics Of Preterm Infants Using Lstm Based Deep Learning Model, Soniya Poudel Chhetri

Electrical Engineering Theses

Babies born prematurely are more likely to experience serious medical problems called Bradycardia, where their heart rate drops below 100 beats per minute(bpm). Bradycardia can decrease cerebral blood velocities by 10-50% from their normal level [6], potentially harming the infant's developing brain and other vital organs. Healthcare professionals working in Neonatal Intensive Care Units (NICUs) face challenges evaluating the likelihood of these events occurring in preterm babies based on their physiological signals. Forecasting and tracking bradycardia events before time will help save thousands of preterm infants from losing their lives. While time series analysis of heart rate data is one …

Geopolitics Of Semiconductor Supply Chains: The Case Of Tsmc, Us-China-Taiwan Relations, And The Covid-19 Crisis, Aditya Sehgal

Independent Study Project (ISP) Collection

As the demand for more advanced forms of technology continues to grow, so does the global importance and reliance on semiconductors. This research paper examines the impact of semiconductor shortages on both consumer and military production, as well as the geopolitical implications embedded within the global supply chain.

The paper begins by providing an overview of semiconductors, the global semiconductor market, and the impact of COVID-19 on the industry’s supply chain. It also discusses the importance of the Taiwan Semiconductor Manufacturing Company (TSMC) in the industry and its role in addressing semiconductor shortages.

Next, the paper discusses the impact of …

Para Cima Y Pa’ Abajo: Building Bridges Between Hci Research In Latin America And In The Global North, Pedro Reynolds-Cuéllar, Marisol Wong-Villacres, Karla A. Badillo-Urquiola, Mayra Donaji Barrera-Machuca, Franceli L. Cibrian, Marianela Ciolfi Felice, Carolina Fuentes, Laura Sanely Gaytán-Lugo, Vivian Genaro Motti, Monica Perusquía-Hernández, Oscar A. Lemus

Engineering Faculty Articles and Research

The Human-computer Interaction (HCI) community has the opportunity to foster the integration of research practices across the Global South and North to begin overcoming colonial relationships. In this paper, we focus on the case of Latin America (LATAM), where initiatives to increase the representation of HCI practitioners lack a consolidated understanding of the practices they employ, the factors that influence them, and the challenges that practitioners face. To address this knowledge gap, we employ a mixed-methods approach, comprising a survey (66 respondents) and in-depth interviews (19 interviewees). Our analyses characterize a set of research perspectives on how HCI is practiced …

Spatial And Temporal Solar Potential Variation Analysis In Uganda Using Measured Data, Daniel N Katongole, Karidewa Nyeinga, Denis Okello, Daniel Mukiibi, James Mubiru, Yeeko Kisira

Tanzania Journal of Science

The paper presents an analysis of spatial and temporal solar potential variations in Uganda. The solar radiation potential distribution was investigated based on measured data from 56 ground meteorological stations across Uganda from January 2015 to February 2022. The data were recorded after every 5-minute interval. The monthly average daily Global Horizontal Irradiance (GHI) was analysed using the spatial inverse distance weighting (IDW) interpolation technique in ArcGIS 10.7.1. The GHI distribution was found to have maxima at equinox and minimum between June and July. The average global horizontal irradiation is found to be 1680 KWh per year, with a daily …

Artificial Neural Network-Based Prediction Assessment Of Wire Electric Discharge Machining Parameters For Smart Manufacturing, Itagi Vijayakumar Manoj, Sannayellappa Narendranath, Peter Madindwa Mashinini, Hargovind Soni, Shanay Rab, Shadab Ahmad, Ahatsham Hayat

Department of Electrical and Computer Engineering: Faculty Publications

Artificial intelligence (AI), robotics, cybersecurity, the Industrial Internet of Things, and blockchain are some of the technologies and solutions that are combined to produce “smart manufacturing,” which is used to optimize manufacturing processes by creating and/or accepting data. In manufacturing, spark erosion technique such as wire electric discharge machining (WEDM) is a process that machines different hard-to-cut alloys. It is regarded as the solution for cutting intricate parts and materials that are resistant to conventional machining techniques or are required by design. In the present study, holes of different radii, i.e. 1, 3, and 5mm, have been cut on Nickelvac-HX. …

H-Plane Siw Horn Antenna With Enhanced Front-To-Back Ratio For 5g Applications, Özlem Akgün, Nurhan Türker Tokan

Turkish Journal of Electrical Engineering and Computer Sciences

Millimeter-wave (mmWave) antennas are indispensable components in the fifth-generation (5G) wireless communication systems. With the inherent advantages of integration capability, substrate integrated waveguide (SIW) antenna is an excellent choice for applications in the mmWave frequency bands. However, reflection losses occur at dielectric-filled thin apertures of SIW antennas. These reflections can be overcome by impedance matching between the aperture and the free space. In this study, we introduce an mmWave SIW horn antenna having impedance matching transitions (IMTs) across the horn's aperture width. The designed antenna, operating in the 24-28 GHz band, is simulated with a full-wave analysis tool. The simulation …

Boomerang Algorithm Based On Swarm Optimization For Inverse Kinematics Of 6 Dof Open Chain Manipulators, Okan Duymazlar, Di̇lşad Engi̇n

Turkish Journal of Electrical Engineering and Computer Sciences

In this study, a feasible swarm intelligence algorithm is proposed that computes the inverse kinematics solution of 6 degree of freedom (DOF) industrial robot arms, which are frequently used in industrial and medical applications. The proposed algorithm is named as Boomerang algorithm due to its recursive structure. The proposed algorithm aims to reduce the computation time to feasible levels without increasing the position and orientation errors. In order to reduce the computational time in swarm optimization algorithms and increase feasibility, an alternative definition method was used instead of the DH method in defining the robot arm kinematic configuration. The effect …

Validation Of Bottom-Up Gnss Radio Occultation Method To Measure D- And E-Region Electron Density, Dylan J. Shaver

Theses and Dissertations

An in-depth validation of a new bottom-up approach using GNSS Radio Occultation (GNSS-RO) data to generate electron density profiles in the D- and E-region ionosphere. This comparison was completed using daytime ionosonde profiles when sporadic-E (E_s) was not present, and corresponding FIRI profiles. The average GNSS-RO profile is a few kilometers higher in altitude than the ionosonde profiles at the minimum frequency, f min. When the ionosonde profiles are shifted so that the altitudes match at f min, they are in good agreement up to the E-region peak altitude, hmE. Below f min, the …

Design And Concept Of Renewable Energy Driven Auto-Detectable Railway Level Crossing Systems In Bangladesh, Iftekharuzzaman Iftekharuzzaman, Susmita Ghosh, Mohammad K. Basher, Mohammad A. Islam, Narottam Das, Mohammad Nur-E-Alam

Research outputs 2022 to 2026

Bangladesh’s railway system mostly uses typical manual railway crossing techniques or boom gates through its 2955.53 km rail route all over the country. Accidents frequently happen at railway crossings due to the lack of quickly operating gate systems, and to fewer safety measures at the railway crossing as well. Currently, there are very few automatic railway crossing systems available (without obstacle detectors). Additionally, all of them are dependent on the national power grid, without a backup plan for any emergency cases. Bangladesh is still running a bit behind in generating enough power for its consumption; hence, it is not possible …

Design Of International Airport Hybrid Renewable Energy System, Aviti Thadei Mushi

Tanzania Journal of Engineering and Technology (TJET)

This paper presents the design and simulation of a hybrid renewable energy system utilizing solar and wind energy sources with a backup generator. The demand for reliable electric energy in support of investments in large social and economic development activities such as airport operations has been an agenda worldwide. In Tanzania, Mwanza International Airport (MIA) expects to consume about 18 MVA of electric power annually to support its operations for the next 25 years. About 78-80% of the world's commercial energy comes from fossil fuels. Non-renewable fuels and other negative effects contribute to global warming through greenhouse gas emissions and …

Sensible Heat Bean Cooker, Casiana Lwiwa

Tanzania Journal of Engineering and Technology (TJET)

Alternative cooking energy to replace wood fuels is needed in the African context. Liquified Natural Gas (LNG) is a solution but is still based on burning fossil fuel. Electrical cookers can be an alternative as well. However, for off-grid systems this means electrical batteries are required, as the solar electricity from Photovoltaic (PV) panels is intermittent, and as cooking is also to be made after sunset. Heat storage technologies can provide solutions where available energy is stored in the form of heat for cooking when needed. The challenge is then to develop systems which are robust, safe, and technically simple. …

Development Of Solar Pv Systems For Mini-Grid Applications In Tanzania, Seleman Mayanjo

Tanzania Journal of Engineering and Technology (TJET)

Access to electricity offers great benefits to development through the provision of reliable and efficient energy sources in the country. Majority of the population living in the remote and rural areas of developing countries mostly sub-Saharan Africa are not supplied with electricity. Although the governments through their electricity companies put their effort to extends the grid distribution networks to remote and rural areas still the coverage were not sufficiently enough due to growing demands for safe and reliable electricity. However, solar as a source of energy remains the least utilized energy source in many countries including Tanzania. Solar Photovoltaic (PV) …

Digital Twin Applications In 3d Concrete Printing, Yuxin Wang, Farhad Aslani, Arcady Dyskin, Elena Pasternak

Research outputs 2022 to 2026

The benefits of 3D concrete printing (3DCP) include reducing construction time and costs, providing design freedom, and being environmentally friendly. This technology is expected to be effective in addressing the global house shortage. This review highlights the main 3DCP applications and four critical challenges. It is proposed to combine 3D concrete printing with Digital Twin (DT) technology to meet the challenges the 3DCP faces and improve quality and sustainability. This paper provides a critical review of research into the application of DT technology in 3DCP, categorize the applications and directions proposed according to different lifecycles, and explore the possibility of …

Biocybersecurity And Deterrence: Hypothetical Rwandan Considerations, Issah Samori, Gbadebo Odularu, Lucas Potter, Xavier-Lewis Palmer

Community & Environmental Health Faculty Publications

Digitalization and sustainability are popular words within modern disciplines as practitioners each look toward the future of their respective fields. Specifically for the African continent, which is making great strides in developmental targets, those two terms are central to core aspects of policy initiatives that may foster cooperation across its varied lands and nations. One of the underlying challenges that confront Africa is a lack of strong regional integration across socioeconomic and political programs; there is value in African regions having more regional connectedness. We assess the rate of regional integration and development in Africa and discuss how to alleviate …

The Development Of Dark Hyperspectral Absolute Calibration Model Using Extended Pseudo Invariant Calibration Sites At A Global Scale: Dark Epics-Global, Padam Bahadur Karki

Electronic Theses and Dissertations

This research aimed to develop a novel dark hyperspectral absolute calibration (DAHAC) model using stable dark targets of "Global Cluster - 36" (GC-36), one of the clusters from "300 Class Global Classification." The stable dark sites were identified from GC-36 called "Dark EPICS-Global" covering the surface types viz; dark rock, volcanic area, and dark sand. The Dark EPICS-Global shows a temporal variation of 0.02 unit reflectance. This work uses the Landsat-8 (L8) Operational Land Imager (OLI) , Sentinel-2A (S2A) Multispectral Instrument (MSI) , and Earth Observing One (EO-1) Hyperion data for the DAHAC model development, where well-calibrated L8 and S2A …

A Type-2 Fuzzy Rule-Based Model For Diagnosis Of Covid-19, İhsan Şahi̇n, Erhan Akdoğan, Mehmet Emi̇n Aktan

Turkish Journal of Electrical Engineering and Computer Sciences

In this study, a type-2 fuzzy logic-based decision support system comprising clinical examination and blood test results that health professionals can use in addition to existing methods in the diagnosis of COVID-19 has been developed. The developed system consists of three fuzzy units. The first fuzzy unit produces COVID-19 positivity as a percentage according to the respiratory rate, loss of smell, and body temperature values, and the second fuzzy unit according to the C-reactive protein, lymphocyte, and D-dimer values obtained as a result of the blood tests. In the third fuzzy unit, the COVID-19 positivity risks according to the clinical …

Transmission Network Planning For Realistic Egyptian Systems Via Encircling Prey Based Algorithms, Abdullah M. Shaheen, Ragab Elsehiemy, Mohammed Kharrich, Salah Kamel

Turkish Journal of Electrical Engineering and Computer Sciences

Transmission network planning problem (TNPP) is one of the pertinent issues of the planning activities in power systems. It aims to optimally pick out the routs, types, and number of the new installed lines to confront the expected future loading conditions. In this line, this study proposes a new economic model to the TNPP. The aim of the model is to find the optimal transmission routes at least investment and operating costs. Three recent algorithms called grey wolf optimization algorithm (GWOA), spotted hyena optimization algorithm (SHOA) and whale optimization algorithm (WOA) are developed to solve the TNPP. The concept of …

Lidar Remote Sensing Of Aerosol And Ozone Profiles And Application To Air Quality Studies In New York City Area, Dingdong Li

Dissertations and Theses

Ozone (O₃) and PM2.5 (Particulate Matter with a diameter less than 2.5 μm) are the main pollutants in New York City (NYC) due to high levels of anthropogenic emissions, complex urban meteorology, and regional transport. However, vertical distribution observations are still lacking. This thesis utilizes lidar remote sensing techniques to retrieve the vertical distribution of O₃ and aerosols and study air pollution episodes in the NYC metropolitan area.

The thesis includes three parts. The first part analyzes continuous ceilometer observations of aerosols and atmospheric mixed-layer height (ML). We investigate the vertical, diurnal, and seasonal characteristics of the …