Open Access. Powered by Scholars. Published by Universities.®
Electrical and Computer Engineering
Electrical and Computer Engineering Faculty Research & Creative Works
Articles 1 - 8 of 8
Full-Text Articles in Engineering
Dc Power Bus Modeling Using A Circuit Extraction Approach Based On A Mixed-Potential Integral Equation Formulation And An Iterative Equation Solver, Jun Fan, James L. Drewniak, James L. Knighten
Dc Power Bus Modeling Using A Circuit Extraction Approach Based On A Mixed-Potential Integral Equation Formulation And An Iterative Equation Solver, Jun Fan, James L. Drewniak, James L. Knighten
Electrical and Computer Engineering Faculty Research & Creative Works
A quick and simple approach is developed to perform circuit simulations for an equivalent circuit extracted from a first principles formulation for DC power bus structures. The simulations are done by solving the system equation using an iterative method. Good agreement between modeling and measurements demonstrate the effectiveness of the method, which is very suitable and computationally efficient for frequency-domain DC power modeling.
Dc Power Bus Design With Fdtd Modeling Including A Dispersive Media, Xiaoning Ye, Jun Fan, Marina Koledintseva, James L. Drewniak
Dc Power Bus Design With Fdtd Modeling Including A Dispersive Media, Xiaoning Ye, Jun Fan, Marina Koledintseva, James L. Drewniak
Electrical and Computer Engineering Faculty Research & Creative Works
DC power-bus modeling in high-speed digital design using the FDTD method is reported here. The dispersive medium is approximated by a Debye model to account for the loss. A wide band frequency response (100 MHz-5 GHz) is obtained through a single FDTD simulation. Favorable agreement is achieved between the modeled and measured results for a typical DC power-bus structure with multiple SMT decoupling capacitors mounted on the board. The FDTD tool is then applied to investigate the effects of local decoupling on a DC power-bus. The modeled results agree with the results from another modeling tool, the CEMPIE (a circuit …
Development Of A Closed-Form Expression For The Input Impedance Of Power-Ground Plane Structures, Minjia Xu, Yun Ji, Todd H. Hubing, Thomas Van Doren, James L. Drewniak
Development Of A Closed-Form Expression For The Input Impedance Of Power-Ground Plane Structures, Minjia Xu, Yun Ji, Todd H. Hubing, Thomas Van Doren, James L. Drewniak
Electrical and Computer Engineering Faculty Research & Creative Works
This paper analyzes the fundamental behavior of PCB power bus structures using the modal expansion method. The results are validated by experiments and full-wave numerical modeling. It is shown that the power bus can be modeled as a series LeC circuit below the first board resonance frequency. C is the interplane capacitance and Le is an effective inductance contributed by all the cavity nodes. The effects of the layer thickness, port location, board size and the feeding wire radius on the value of Le are discussed in this study. Le can be estimated from the …
Emc Analysis Of An 18" Lcd Monitor, Theodore M. Zeeff, Todd H. Hubing, James L. Drewniak, Richard E. Dubroff, Thomas Van Doren
Emc Analysis Of An 18" Lcd Monitor, Theodore M. Zeeff, Todd H. Hubing, James L. Drewniak, Richard E. Dubroff, Thomas Van Doren
Electrical and Computer Engineering Faculty Research & Creative Works
This paper describes a case study covering the evaluation and reduction of the radiated EMI from an 18 inches Liquid Crystal Display (LCD) monitor. The evaluation was completed in two parts: first potential EMI sources at the Printed Circuit Board (PCB) level were identified, then the EMI antennas driven by these sources were analyzed. Methods for reducing the EMI were described in detail, and where applicable, those modifications were applied. Radiated measurements demonstrate the effectiveness of these recommendations.
Fdtd Modeling Of Lumped Ferrites, Min Li, Xiao Luo, James L. Drewniak
Fdtd Modeling Of Lumped Ferrites, Min Li, Xiao Luo, James L. Drewniak
Electrical and Computer Engineering Faculty Research & Creative Works
Implementing ferrites in finite-difference time-domain (FDTD) modeling requires special care because of the complex nature of the ferrite impedance. Considerable computational resources and time are required to directly implement a ferrite in the FDTD method. Fitting the ferrite impedance to an exponential series with the generalized-pencil-of-function (GPOF) method and using recursive convolution is an approach that minimizes the additional computational burden. An FDTD algorithm for a lumped ferrite using GPOF and recursive convolution is presented herein. Two different ferrite impedances in a test enclosure were studied experimentally to demonstrate the FDTD modeling approach. The agreement is generally good.
Emi Reduction From Airflow Aperture Arrays Using Dual-Perforated Screens And Loss, Min Li, Joe Nuebel, James L. Drewniak, Todd H. Hubing, Richard E. Dubroff, Thomas Van Doren
Emi Reduction From Airflow Aperture Arrays Using Dual-Perforated Screens And Loss, Min Li, Joe Nuebel, James L. Drewniak, Todd H. Hubing, Richard E. Dubroff, Thomas Van Doren
Electrical and Computer Engineering Faculty Research & Creative Works
Airflow perforations in shielding enclosures can act as apertures facilitating the coupling from internal sources to external electromagnetic interference (EMI). This EMI radiation for single- and dual-screen configurations was studied herein experimentally and with finite-difference time-domain (FDTD) modeling. A general EMI reduction of more than 20 dB was achieved for dual-perforated screens spaced 1 cm apart when compared to EMI for a single perforated screen. However, in the dual-screen case, the space between the screens can act as a thin cavity, which, in turn, can lead to significant radiation at distinct angles. Damping the resonances by loading the space between …
Emi From Cavity Modes Of Shielding Enclosures-Fdtd Modeling And Measurements, Min Li, Joe Nuebel, James L. Drewniak, Richard E. Dubroff, Todd H. Hubing, Thomas Van Doren
Emi From Cavity Modes Of Shielding Enclosures-Fdtd Modeling And Measurements, Min Li, Joe Nuebel, James L. Drewniak, Richard E. Dubroff, Todd H. Hubing, Thomas Van Doren
Electrical and Computer Engineering Faculty Research & Creative Works
Electromagnetic interference (EMI) from slots and apertures resulting from coupling of interior sources through enclosure cavity modes in a rectangular test enclosure is reported herein. EMI from a specially designed test enclosure with slots or apertures excited by interior sources was studied experimentally and with finite-difference time-domain (FDTD) modeling. The measurements and FDTD modeling agree well. The results indicate that radiation at cavity mode resonances through slots and apertures of nonresonant dimensions can be as significant as the radiation at aperture or slot resonances. The agreement between the FDTD modeling and measurements demonstrates the usefulness of FDTD for investigating aspects …
Advances Of Gyromagnetic Electronics For Emc Problems, Marina Koledintseva, L. K. Mikhailovsky, Alexander A. Kitaytsev
Advances Of Gyromagnetic Electronics For Emc Problems, Marina Koledintseva, L. K. Mikhailovsky, Alexander A. Kitaytsev
Electrical and Computer Engineering Faculty Research & Creative Works
A number of EMC problems at microwaves-detection and measurement of power (spectrum) of the signals and suppression of unwanted radiation-can be solved owing to the results obtained in the field of gyromagnetic (spin) electronics. The latter deals with the unique properties of gyromagnetic media (GM) based on microwave ferrites, including high-anisotropy hexagonal ferrites that do not need an intense magnetization field for their operation at ferromagnetic resonance. Approaches to the study of the interaction of GM with an electromagnetic field and ways of modeling frequency-selective measuring devices, absorbing coatings and all-mode filters of harmonics on the basis of GM are …