Engineering Commons^™

Effects Of Accelerated Carbonation Curing On Co2 Sequestration And On The Compressive Strength Of Concrete Masonry Units, Barry Gilroy, Leon Black, David Thompson, Ronan Hogan, Niall Holmes

Civil Engineering Research in Ireland 2020

The global consumption of Portland cement has risen to over 4 billion tonnes per annum. Its manufacture is energy and carbon intensive and approximately 900 kg of CO₂ is emitted into the atmosphere for each tonne of Portland cement produced. The International Energy Agency (IEA) roadmap sets out a goal to reduce emissions due to cement production to 18 % below 2006 levels by 2050.

Concrete has the potential to re-absorb CO₂ by the process of carbonation, where it reacts with CaO in the concrete to form calcium carbonate. Accelerated carbonation curing (ACC) is a technique for curing …

Towards Improved Sensor Systems For Bridge Structural Health Monitoring, Alan Ferguson, Roger Woods, David Hester

Civil Engineering Research in Ireland 2020

Taking long-term measurements on in-service bridges is challenging due to the lack of easy access to power and communications. Whilst all-in-one, portable sensor data loggers act to address these challenges, they still lack the flexibility to meet evolving measurement needs. This paper presents the design and implementation of a highly flexible, modular sensor system for bridge structural health monitoring research, which has an emphasis on customisability and extensibility to allow it to meet evolving challenges. The architecture incorporates interchangeable sensor modules that allows data acquisition to an on-board Secure Digital card, with timing and synchronisation provided by global positioning system …

Towards Automated Uav Assisted Bridge Inspections Using Photogrammetry And Image Processing Techniques, Habeene Habeenzu, Patrick Mcgetrick, David Hester, Su Taylor, Louie Wong

Civil Engineering Research in Ireland 2020

At the heart of addressing bridge condition challenges are bridge inspections. The main activity during a bridge inspection is close, arm’s length visual inspection of the entire bridge structure. During this process, all defects such as cracks, spalls and material degradation are manually recorded on the bridge itself and on inspection forms. Where access is difficult such as where a safe working platform cannot be mounted under bridge decks, or on high bridges, expensive underbridge equipment is required which when used results in expensive lane closures. Furthermore, visual inspections have been shown to lack consistency from inspector to inspector and …

Acceleration Based Bridge Weigh In Motion Using Moving Force, Shou Wang, Daniel Mccrum, Eugene O'Brien

Civil Engineering Research in Ireland 2020

Measuring vehicle axles weights is an important method to control traffic and monitor infrastructure. Traditional methods of measuring the static weight of vehicles at a weigh station is disruptive and time consuming. It is more cost effective and efficient to indirectly measure moving vehicle weights crossing a bridge. The weigh-in-motion concept, first proposed by Moses (1979) is an algorithm that uses measured bridge structural response (deflection, strain, …) due to passing vehicles to and a theoretical response. Moving Force identification (MFI) is a variation of the dynamic WIM algorithm that gives a force time history as a vehicle passes the …

A Two-Stage Direct Integration Approach To Find The Railway Track Profile Using In-Service Trains, Yifei Ren, Jennifer Kennahan, Eugene O'Brien

Civil Engineering Research in Ireland 2020

The railway track is an important element in transportation networks. In recent years, drive-by monitoring of railways has become more popular. Using data measured from in-service trains, the railway profile can be found. In previous research, a complex optimiziton method is used to calculate the railway profile. This paper introduces a new two-stage direct integration approach to find the same track profile much more efficiently. The calculated track profile is similar to a ‘true’ profile and can be used to monitor the condition of the track.

Investigating The Contact-Point Response For Drive-By Damage Detection In Bridges, Robert Corbally, Abdollah Malekjafarian

Civil Engineering Research in Ireland 2020

Bridges are critical elements in any road or rail transport network and ensuring their safety is paramount. Recent years have seen significant research efforts to develop cost-effective techniques for bridge monitoring on a large scale. Drive-by bridge inspection techniques, whereby sensors inside a vehicle are used to monitor bridge condition, are at the focus of much of this work. This paper develops a relationship between the measured response in a vehicle and the contact-point response between the wheel and the surface of a bridge using a quarter-car representation of the vehicle. Numerical simulations are carried out to examine the feasibility …

Application Of The Iec Technical Specification For Assessment Of Wave Energy Resource: A Case Study From The West Coast Of Ireland, Iulia Anton, Stephen Nash

Civil Engineering Research in Ireland 2020

There is significant interest globally in harnessing our ocean wave energy resource, estimated at approximately 30,000 TWh/year. The key to this is understanding the resource. The International Electrotechnical Commission (IEC) has developed a technical specification for the evaluation of wave energy resource, IEC-TS 62600- 101: Wave energy resource assessment and characterization. This research applies the IEC standard for a resource characterization study of the Atlantic Marine Energy Test Site on the west coast of Ireland. A key focus is the comparison of the detailed IEC validation approach using scatter diagrams with the traditional timeseries validation approach. Coarse (0.005°) and fine …

Wind Power Prediction And Early Downtime Detection For Ireland, Vikram Pakrashi, Basuraj Bhowmik, Juan Manuel González-Sopeña, Paul Mucchielli, Bidisha Ghosh

Civil Engineering Research in Ireland 2020

Wind energy must be commercially competitive to be economically sustainable. Existing wind farms in Ireland must be more efficient to meet the 2009 EU Renewable Energy Directive target of 7% of total energy demand from onshore wind energy farms, which is 45% of the total national renewable energy target of 16%. WindPearl - a Sustainable EnergyAuthority of Ireland (SEAI) funded project is currently looking into improvin operations & maintenance (O&M) of onshore wind turbine farms in Ireland.

An Experimental Investigation Of The Optimum Properties And Conditions For Use Of Anionic Emulsions In Road Maintenance Applications, Simonas Ignatavicius, Alan Kavanagh, David Colleran, Michael J. Brennan, Shane Newell

Civil Engineering Research in Ireland 2020

Bitumen emulsions are used for a range of road maintenance applications, including surface dressing, gravel seals, slurry seals, tack coating, cold-mix asphalt and in situ pavement recycling. The emulsions used can be classified as being either cationic (i.e. possessing a positive electrostatic surface charge) or anionic (i.e. carrying a negative electrostatic surface charge). The vast majority of emulsions used for such applications in Europe are cationic, while anionic bitumen emulsions are used widely throughout North America and Africa. The aims of the experimental study described in this paper were (a) to investigate why one or the other emulsion type is …

A Review Of Vision Based Methods For Pothole Detection And Road Profile Analysis, Darragh Lydon, Su Taylor, Myra Lydon, Julia Early

Civil Engineering Research in Ireland 2020

This paper is an overview of the development and application of Computer Vision for the detection of pothole, pavement distress and road profile analysis and categorisation. A brief explanation of the traditional methods for determining these factors is given, followed by a chronological description of the evolution and the challenges of using Computer Vision (CV) approaches to determine these conditions. The paper is separated into sections aligned to image capture and analysis methodologies. Qualitative evaluations and comparison of these methods have been provided along with the proposal of guidelines for new computer vision-based road analysis systems.

Analysis And Optimisation Of Tii’S Pams Reset Values And Deterioration Models For Irish Pavement Conditions, James Quinn, Raymond Mcgowan, Tomas O'Flaherty

Civil Engineering Research in Ireland 2020

Ireland has a national road network of approximately 5300km that is managed by Transport Infrastructure Ireland (TII). TII create yearly pavement maintenance and renewal programs from the operation of a Pavement Asset Management System (PAMS). Accurate pavement deterioration models and reset values are an essential part of PAMS and are required for life cycle cost analysis (LCCA). Pavement maintenance and renewal schemes are prioritised based on the LCCA's largest benefit to cost ratio, and therefore optimise the annual pavement maintenance and renewal budget. Currently, TII implement pavement deterioration models and reset values from Austria's and Belgium's PAMS, and are not …

An Analysis Of The Effectiveness Of Bitumen Additives On The Performance Of Pavement Surface Dressings, Alan Anderson, John Casserly, Alan Kavanagh, Jim Campbell

Civil Engineering Research in Ireland 2020

Surface dressing is a maintenance technique that uses thin layers of bitumen emulsion and single sized aggregates. The surface dressing process seals and binds the surface of a road to protect its substructure from water ingress. It also provides increased skid resistance, which improves safety for road users. Early life chip-loss can occur if there is an insufficient degree of adhesion between the emulsion and aggregate used. The range of additives used in bitumen can have an effect on their adhesion properties. The focus of this research project was to investigate if the use of these additives in surface dressing …

Winter Maintenance On The Irish Road Network, Hugh Mcconnell, Brian Mccann

Civil Engineering Research in Ireland 2020

Winter maintenance relates to those activities undertaken where the objective is to minimise the impact of frost, ice or snow on the travelling public. The responsibility for winter maintenance of all roads in Ireland currently rests with local authorities and Transport Infrastructure Ireland (TII) (Formerly the NRA) on behalf of the Department of Transport, Tourism and Sport (DTTaS), (DTTaS, 2017). The aim of the study was to examine current winter maintenance practices undertaken in Ireland by local authorities and the Motorway Maintenance and Renewals Contracts (MMaRC) contractors and examine the potential financial, operational and environmental benefits if pre-wet and brine …

An Experimental Investigation Of The Optimum Properties And Conditions For Use Of Anionic Emulsions In Road Maintenance Applications, Simonas Ignatavicius, Alan Kavanagh, David Colleran, Michael J. Brennan, Shane Newell

Civil Engineering Research in Ireland 2020

Bitumen emulsions are used for a range of road maintenance applications, including surface dressing, gravel seals, slurry seals, tack coating, cold-mix asphalt and in situ pavement recycling. The emulsions used can be classified as being either cationic (i.e. possessing a positive electrostatic surface charge) or anionic (i.e. carrying a negative electrostatic surface charge). The vast majority of emulsions used for such applications in Europe are cationic, while anionic bitumen emulsions are used widely throughout North America and Africa. The aims of the experimental study described in this paper were (a) to investigate why one or the other emulsion type is …

A Review Of Vision Based Methods For Pothole Detection And Road Profile Analysis, Darragh Lydon, S. E. Taylor, Myra Lydon, Julia Early

Civil Engineering Research in Ireland 2020

This paper is an overview of the development and application of Computer Vision for the detection of pothole, pavement distress and road profile analysis and categorisation. A brief explanation of the traditional methods for determining these factors is given, followed by a chronological description of the evolution and the challenges of using Computer Vision (CV) approaches to determine these conditions. The paper is separated into sections aligned to image capture and analysis methodologies. Qualitative evaluations and comparison of these methods have been provided along with the proposal of guidelines for new computer vision-based road analysis systems.

Analysis And Optimisation Of Tii’S Pams Reset Values And Deterioration Models For Irish Pavement Conditions, James Quinn, Raymond Mcgowan, Tomas O'Flaherty

Civil Engineering Research in Ireland 2020

Ireland has a national road network of approximately 5300km that is managed by Transport Infrastructure Ireland (TII). TII create yearly pavement maintenance and renewal programs from the operation of a Pavement Asset Management System (PAMS). Accurate pavement deterioration models and reset values are an essential part of PAMS and are required for life cycle cost analysis (LCCA). Pavement maintenance and renewal schemes are prioritised based on the LCCA's largest benefit to cost ratio, and therefore optimise the annual pavement maintenance and renewal budget. Currently, TII implement pavement deterioration models and reset values from Austria's and Belgium's PAMS, and are not …

An Analysis Of The Effectiveness Of Bitumen Additives On The Performance Of Pavement Surface Dressings, Alan Anderson, John Casserly, Alan Kavanagh, Jim Campbell

Civil Engineering Research in Ireland 2020

Surface dressing is a maintenance technique that uses thin layers of bitumen emulsion and single sized aggregates. The surface dressing process seals and binds the surface of a road to protect its substructure from water ingress. It also provides increased skid resistance, which improves safety for road users. Early life chip-loss can occur if there is an insufficient degree of adhesion between the emulsion and aggregate used. The range of additives used in bitumen can have an effect on their adhesion properties. The focus of this research project was to investigate if the use of these additives in surface dressing …

Winter Maintenance On The Irish Road Network, Hugh Mcconnell, Brian Mccann

Civil Engineering Research in Ireland 2020

Winter maintenance relates to those activities undertaken where the objective is to minimise the impact of frost, ice or snow on the travelling public. The responsibility for winter maintenance of all roads in Ireland currently rests with local authorities and Transport Infrastructure Ireland (TII) (Formerly the NRA) on behalf of the Department of Transport, Tourism and Sport (DTTaS), (DTTaS, 2017). The aim of the study was to examine current winter maintenance practices undertaken in Ireland by local authorities and the Motorway Maintenance and Renewals Contracts (MMaRC) contractors and examine the potential financial, operational and environmental benefits if pre-wet and brine …

Feasibility And Implications Of The Modular Construction Approach For Rapid Post-Disaster Recovery, Jin Choi, Pedram Ghannad, Yong-Cheol Lee

Civil and Environmental Engineering and Construction Faculty Research

The adverse social and financial impacts of catastrophic disasters are increasing as population centers grow. In recent years, destroying homes and infrastructures has resulted in a major loss of life and created countless refugees. For example, Hurricane Katrina in August 2005 damaged over 214,700 homes in New Orleans and forced over 800,000 citizens to live outside of their homes due to flooding. After disastrous events, the government agencies have to respond to post-disaster housing issues quickly and efficiently and provide sufficient resources for temporary housing for short-term disaster relief and reconstruction of destroyed and damaged housing for full rehabilitation. Modular …

Feasibility And Implications Of The Modular Construction Approach For Rapid Post-Disaster Recovery, Jin Choi, Pedram Ghannad, Yong-Cheol Lee

Civil and Environmental Engineering and Construction Faculty Research

The adverse social and financial impacts of catastrophic disasters are increasing as population centers grow. In recent years, destroying homes and infrastructures has resulted in a major loss of life and created countless refugees. For example, Hurricane Katrina in August 2005 damaged over 214,700 homes in New Orleans and forced over 800,000 citizens to live outside of their homes due to flooding. After disastrous events, the government agencies have to respond to post-disaster housing issues quickly and efficiently and provide sufficient resources for temporary housing for short-term disaster relief and reconstruction of destroyed and damaged housing for full rehabilitation. Modular …

Study The Effect Of Damping Change During The Dynamic Analysis Of A Reinforced Concrete Bridge With Neoprene Cushions, Mais Ghassoun

Emirates Journal for Engineering Research

The damping ratio has a important effect on the dynamic behavior of the bridges. and it is customary when designing to assume it as a predetermined fixed value independent of the response amplitude and frequency of the structure . A lot of experimental research worked on identifying them, but the dependence of damping and other dynamic characteristics of vibration amplitudes and their impact on responses and the results of the analysis need more scrutiny and simulation due to the difficulty of conducting vibration experiments for structures of realistic dimensions and large weights such as a RC bridge, which necessitated a …

Future Trends In Construction Waste Management, Zaur Zeynalov

International Programs

The problem of construction waste has been with us since the beginning of construction history. As the world's population continues to grow, construction waste grows with it and there is a pressing need to address how we deal with the construction waste problem As a result, the whole world is facing the problem of "construction waste management" today. This poster describes current challenges managing construction waste and offers possible solutions to minimize/mitigate/ameliorate its (negative) effects on the environment.

Improving Energy Efficiency In Residential Houses In Kosovo, Fatlum Rexhepi

International Programs

Buildings with poor insulation and infiltration in doors, windows, and other openings have very high heating and cooling demands. Due to lack of maintenance, building materials, and standard they are whopping consumers. The necessity to save energy is enormous, especially with newly environmental constrains. Moreover, this would not only save our natural resources, but it would cut large sums that households spend on electricity, gas, or coal. Thermodynamic calculation of heat gain and loss gave us a lucid picture of benefits respecting nearly zero energy buildings standards while comparing same building prior and after improving its envelope. The consumption after …

Quantitative Analysis Of The Impacts Of Out-Of-Sequence Work On Project Performance, Michael W. Ibrahim, Awad S. Hanna, Jeffrey S. Russell, Ibrahim S. Abotaleb, Islam H. El-Adaway

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Although out-of-sequence work (OOS) is often cited as a recurring challenge that impacts project performance, it has not been fully addressed in the existing literature as a standalone topic. This paper addresses this gap, defining OOS work as an activity or series of activities that was not performed according to baseline planned logical productive sequencing. By developing a project-based survey and contacting 300 professionals, extensive data were gathered from 42 projects. Using these data, the impacts of OOS were examined. It was found that, on average, approximately 15% of project activities are performed as OOS, resulting in 33% growth in …

Data Quality And Reliability Assessment Of Wearable Emg And Imu Sensor For Construction Activity Recognition, Srikanth Sagar Bangaru, Chao Wang, Fereydoun Aghazadeh

Faculty Publications

The workforce shortage is one of the significant problems in the construction industry. To overcome the challenges due to workforce shortage, various researchers have proposed wearable sensor-based systems in the area of construction safety and health. Although sensors provide rich and detailed information, not all sensors can be used for construction applications. This study evaluates the data quality and reliability of forearm electromyography (EMG) and inertial measurement unit (IMU) of armband sensors for construction activity classification. To achieve the proposed objective, the forearm EMG and IMU data collected from eight participants while performing construction activities such as screwing, wrenching, lifting, …

Entrepreneurial Based Project: Minority Owned Guardrail Installation Company, Nicholas Rubio

Construction Management

This company will provide commercial and highway guardrail installation services to the Northern California Region. The organization will retain a Minority Owned Business Certification and will operate under a Class C-32 License for Parking and Highway Improvement. Due to the large backlog of guardrail projects and the lack of qualified contractors in Northern California, the company plans to partner with existing firms that are unable to take on work. After firmly establishing ourselves in the private commercial market, the organization plans to migrate to public road work where the Minority Owned title can provide more benefit. Through this process we …

Wind Uplifting Performance Of Roof-To-Wall Connections And Roof Structures With Elastomeric Adhesives In Light-Frame Wood Buildings, Bilal M. Alhawamdeh

Dissertations

Light-frame wood residential buildings are highly susceptible to damage caused by severe wind events such as hurricanes and tornados. Roof failures in residential buildings are commonly observed due to weaknesses of or missing connections. Roof-to-wall connections not only have significant influences on roof performance but also affect building resistance due to their critical role of transferring wind loads to the wall system and ultimately to the foundation. Roof fails when it has no sufficient wind uplift resistance due to improper selection or installation of construction materials (including fasteners) and strength degradation due to aging or long service. Toenailing is commonly …

Performance Testing Of Hot Mix Asphalt Containing Biochar, Shadi Saadeh, Yazan Al-Zubi, Basel Zaatarah

Mineta Transportation Institute

In recent years, researchers have been able to identify asphalt binder additives, such as polymers and bio-binder, that can enhance the rheological and mechanical properties of asphalt binders. Earlier studies show that utilizing bio-binder as a partial replacement for asphalt binder has shown promising results in both mechanical and sustainability aspects. Biochar additions improved binder viscosity and low-temperature characteristics. Biochar, which is a byproduct of producing bio-binder, has shown enhanced rheological and mechanical properties when used as an additive to the asphalt binder. In this study, the mechanical properties of asphalt mixtures containing Biochar were investigated. In addition, its color …

Examining The Effects Of Reducing The Cement Content Of Portland Cement Concrete Pavement, Bryan Casillas

Graduate Theses and Dissertations

Portland cement is a significant component in a concrete mixture. For concrete used in portland cement concrete pavement (PCCP), the Arkansas Department of Transportation (ARDOT) specifies a minimum cementitious material content of 564 lb/yd3 and a maximum water-cementitious material ratio of 0.45. Prior research conducted at the University of Arkansas, TRC 0603, indicated concrete mixtures used in five bridge decks throughout Arkansas achieved the required 28-day strength at seven days, and the measured compressive strength at 28 days was 30% greater than required. The use of high strength concrete in pavements throughout the state can increase cracking and consequently reduce …

Quantifying Workability, Compactability, And Cohesion Gain Of Asphalt Emulsion Cold In-Place Recycling, Sadie Casillas

Graduate Theses and Dissertations

To maximize the life and quality of a pavement, proper maintenance and rehabilitation are essential. Strategies for pavement rehabilitation with many sustainable benefits are pavement recycling. This dissertation focuses on two types of in-situ pavement recycling: Cold in-place recycling (CIR) stabilized with asphalt emulsion and full depth reclamation (FDR) stabilized with asphalt emulsion or foamed asphalt. One white paper (Chapter 2), two accepted peer reviewed journal articles (Chapters 3 and 4), and one submitted peer reviewed journal article (Chapter 5) are presented in this document to create better understanding of the unique material characterization of asphalt emulsion cold recycled materials, …