Engineering Commons^™

A Study Of The Impacts Of Freeze-Thaw On Cliff Recession At The Calvert Cliffs In Calvert County, Maryland, Bonnie Elizabeth Zwissler

Dissertations, Master's Theses and Master's Reports - Open

The Calvert Cliffs, which form much of the western coastline of the Chesapeake Bay in Calvert County, Maryland, are actively eroding and destabilizing, resulting in a critical situation for many homes in close proximity to the slope's crest. Past studies have identified that where waves directly interact with the toe of the slope, wave action controls cliff recession; however, where waves do not regularly interact with the slope toe, the past work identified that freeze-thaw controls recession. This study investigated the validity of this second claim by analyzing the recession rate and freeze-thaw behavior of six study sites along the …

An Investigation Of Waste Glass-Based Geopolymers Supplemented With Alumina, Mary U. Christiansen

Dissertations, Master's Theses and Master's Reports - Open

An increased consideration of sustainability throughout society has resulted in a surge of research investigating sustainable alternatives to existing construction materials. A new binder system, called a geopolymer, is being investigated to supplement ordinary portland cement (OPC) concrete, which has come under scrutiny because of the CO2 emissions inherent in its production.

Geopolymers are produced from the alkali activation of a powdered aluminosilicate source by an alkaline solution, which results in a dense three-dimensional matrix of tetrahedrally linked aluminosilicates. Geopolymers have shown great potential as a building construction material, offering similar mechanical and durability properties to OPC. Additionally, geopolymers have …

The Laboratory Evaluation Of Bio Oil Derived From Waste Resources As Extender For Asphalt Binder, Xu Yang

Dissertations, Master's Theses and Master's Reports - Open

A shortage of petroleum asphalt is creating opportunities for engineers to utilize alternative pavement materials. Three types of bio oils, original bio oil (OB), dewatered bio oil (DWB) and polymer-modified bio oil (PMB) were used to modify and partially replace petroleum asphalt in this research. The research investigated the procedure of producing bio oil, the rheological properties of asphalt binders modified and partially replaced by bio oil, and the mechanical performances of asphalt mixtures modified by bio oil. The analysis of variance (ANOVA) is conducted on the test results for the significance analysis. The main finding of the study includes: …

Stilling Basin Scour Remediation Using Air Injection And Flat Plate Extension, Rachael Barlock

Dissertations, Master's Theses and Master's Reports - Open

The South Florida Water Management District (SFWMD) is responsible for managing over 2500 miles of waterways and hundreds of water control structures. Many of these control structures are experiencing erosion, known as scour, of the sediment downstream of the structure. Laboratory experiments were conducted in order to investigate the effectiveness of two-dimensional air diffusers and plate extensions (without air injection) on a 1/30 scale model of one of SFWMD gated spillway structures, the S65E gated spillway. A literature review examining the results of similar studies was conducted. The experimental design for this research was based off of previous work done …

Structural Control Of A Small-Scale Test-Bed Shaker Structure Using A Sponge-Type Magneto-Rheological Fluid Damper, Benjamin D. Winter

Dissertations, Master's Theses and Master's Reports - Open

Semi-active damping devices have been shown to be effective in mitigating unwanted vibrations in civil structures. These devices impart force indirectly through real-time alterations to structural properties. Simulating the complex behavior of these devices for laboratory-scale experiments is a major challenge. Commercial devices for seismic applications typically operate in the 2-10 kN range; this force is too high for small-scale testing applications where requirements typically range from 0-10 N. Several challenges must be overcome to produce damping forces at this level. In this study, a small-scale magneto-rheological (MR) damper utilizing a fluid absorbent metal foam matrix is developed and tested …

Evaluation Of Intelligent Compaction Control In The M-189 Reconstruction Project At Iron River, Michigan, Junhong Li

Dissertations, Master's Theses and Master's Reports - Open

This research evaluated an Intelligent Compaction (IC) unit on the M-189 highway reconstruction project at Iron River, Michigan. The results from the IC unit were compared to several traditional compaction measurement devices including Nuclear Density Gauge (NDG), Geogauge, Light Weight Deflectometer (LWD), Dynamic Cone Penetrometer (DCP), and Modified Clegg Hammer (MCH). The research collected point measurements data on a test section in which 30 test locations on the final Class II sand base layer and the 22A gravel layer. These point measurements were compared with the IC measurements (ICMVs) on a point-to-point basis through a linear regression analysis. Poor correlations …

Determing The Effect Of Thermal Treatment Timing On Ultra-High Performance Concrete Beams, Christopher H. Mullen

Dissertations, Master's Theses and Master's Reports - Open

The loss of prestressing force over time influences the long-term deflection of the prestressed concrete element. Prestress losses are inherently complex due to the interaction of concrete creep, concrete shrinkage, and steel relaxation. Implementing advanced materials such as ultra-high performance concrete (UHPC) further complicates the estimation of prestress losses because of the changes in material models dependent on curing regime.

Past research shows compressive creep is "locked in" when UHPC cylinders are subjected to thermal treatment before being loaded in compression. However, the current precasting manufacturing process would typically load the element (through prestressing strand release from the prestressing bed) …

Preliminary Investigation Of Ultra-High Performance Concrete Behavior At High Strain Rates Using The Split-Hopkinson Pressure Bar, Jacob Clark

Dissertations, Master's Theses and Master's Reports - Open

Ultra-high performance concrete (UHPC) displays several enhanced material properties compared to normal strength concrete (NSC). In past research, Split-Hopkinson pressure bar (SHPB) tests have been used for normal strength concrete to determine material behavior at high strain rates. The behavior of advanced concrete materials, such as UHPC, under high strain rates has not been thoroughly investigated. While it is generally accepted that concrete materials experience increases in compressive strength under increasing strain rates, a preliminary investigation was conducted to gain insight into the compressive behavior of UHPC under high strain rate SHPB testing.

In this research, 50 specimens were tested …

Mechanical Concrete, Purdue Ect Team

ECT Fact Sheets Archive

Mechanical Concrete® is a way of binding crushed stone aggregates together into a load bearing cellular building unit. The Mechanical Concrete® unit can support compressive loads and resist lateral soil pressure.

Greenpatch® - Cold Mix Asphalt, Purdue Ect Team

ECT Fact Sheets Archive

GreenPatch® is environmentally friendly cold asphalt that is a direct replacement for traditional cold patch in repairing asphalt pavements. This revolutionary breakthrough in the cold asphalt industry contains no petroleum based softeners such as diesel, toluene, kerosene, and naphthalene found in conventional cold asphalt that pose serious threats to human health and the environment.

Tire Log™, Purdue Ect Team

ECT Fact Sheets Archive

The Tire Log™ is a patented innovation made from waste tires with a unique and energy efficient approach to recycling tires. Re-Tread Products (RTP) process takes full advantage of the embedded energy in tires that is wasted in conventional tire recycling that primarily involves the grinding, burying or burning of waste tires.

Bubbledeck, Purdue Ect Team

ECT Fact Sheets Archive

Conventional horizontal concrete slabs are heavy that limit their spans. Enhancement of span results in addition of beams that increases the cost of the structure. Thus, there is a need for a technology that will help in increasing the span by reducing weight of the span. BubbleDeck is a revolutionary construction method that virtually eliminates concrete from the middle of a floor slab between columns that does not perform any structural function, thereby dramatically reducing structural dead weight. BubbleDeck is based on a patented technique - the direct way of linking air and steel.

Bs News January/February

Building Services Engineering

No abstract provided.

Studying Platoon Dispersion Characteristics Under Heterogeneous Traffic In India, Jijo Mathew, Helen Thomas, Anuj Sharma, Lelitha Devi, Laurence Rilett

Department of Civil and Environmental Engineering: Faculty Publications

Platoons are created by signalized intersections which control travel patterns of vehicles. It is common for platoons to disperse during normal traffic operations. While platoon dispersion has been studied extensively under homogenous and lane disciplined traffic conditions, this characteristic under heterogeneous conditions has not been addressed adequately. This study will be one of the first steps in this direction and will lead to better understanding and simulation of platoon dispersion under Indian conditions.

Data describing platoon dispersion was collected with video recording systems along an arterial in Chennai, India. The Robertson’s model parameters calibrated for this data was found to …

Secondary Collisions Revisited: Real-World Crash Data And Relationship To Crash Test Criteria, Randall C. Gowat, Douglas J. Gabauer

Faculty Journal Articles

Objectives: Previous research conducted in the late 1980s suggested that vehicle impacts following an initial barrier collision increase severe occupant injury risk. Now over 25years old, the data are no longer representative of the currently installed barriers or the present US vehicle fleet. The purpose of this study is to provide a present-day assessment of secondary collisions and to determine if current full-scale barrier crash testing criteria provide an indication of secondary collision risk for real-world barrier crashes. Methods: To characterize secondary collisions, 1,363 (596,331 weighted) real-world barrier midsection impacts selected from 13years (1997-2009) of in-depth crash data available through …

Application Of Multi-Hazard Seismic-Blast Detailing For Highway Bridges, Dominique Morton Torres

Dissertations and Theses

The increase of worldwide terrorist attacks on public transportation has heightened our concerns of protecting the nation’s transportation infrastructure. Highway bridges are an attractive target for terrorist attacks due to ease of accessibility and their overall importance to society. The primary objective of this research is to investigate multi-hazard seismic-blast correlations of blast-induced bridge components through numerical simulations of a high-precision finite element model of a typical highway bridge in New York. Seismic-detailing for blast loading on bridges has been investigated to study the correlations between seismic design for blast load effects. High-precision 3D Finite Element models of bridges detailed …

Real-Time Atmospheric Compensation And Surface Temperature Estimates From Satellite Using Neural Networks, Gary Bouton

Dissertations and Theses

Military satellites are being used to determine potential security threats using accurate high sensitivity measurements from defense satellites. These systems focus much more on sensitivity and Signal/Noise Ratio (SNR) than on multispectral capability. Therefore, these systems are highly vulnerable to thermal absorption and reemission that can affect the thermal signature prior to launch. In particular, there is a need to use additional assets to estimate the atmospheric temperature and water vapor profile so that an estimate of the atmospheric processes can be obtained and a correction developed to improve the thermal detection. In particular, the use of existing meteorological geostationary …

Reliability Analysis Of The Hec-18 Scour Equation And Aashto Deep Foundation Design Codes, Jun Yan

Dissertations and Theses

This research project studied the reliability of driven pile foundations subjected to scour, gravity loads including dead loads and live loads, and their combinations. The design of the foundation followed the procedures of the AASHTO LRFD Bridge Design Specification. The design methods were the HEC-18 pier scour equation used to determine the scour depth, and the α-Method and Nordlund-Thurman Method used to design the driven pile. The limit state considered was the axial bearing resistance of the piles in the soil. The reliability indexes for bridges subjected to maximum expected scour depth and gravity loads were found through Monte Carlo …

Estimation Of Performance Indices For The Planning Of Sustainable Transportation Systems, Alexander Paz, Pankaj Maheshwari, Pushkin Kachroo, Sajjad Ahmad

Civil and Environmental Engineering and Construction Faculty Research

In the context of sustainable transportation systems, previous studies have either focused only on the transportation system or have not used a methodology that enables the treatment of incomplete, vague, and qualitative information associated with the available data. This study proposes a system of systems (SOS) and a fuzzy logic modeling approach. The SOS includes the Transportation, Activity, and Environment systems. The fuzzy logic modeling approach enables the treatment of the vagueness associated with some of the relevant data. Performance Indices (PIs) are computed for each system using a number of performance measures. The PIs illustrate the aggregated performance of …

Effects Of Openings On The Analysis And Design Of Precast Prestressed Hollow Core Slabs, Eoghan Lodge

Theses

Precast prestressed hollow core floors are a widely used structural element which offers increased speed of construction, reduced self-weight and many other advantages. Due to the relatively low span-to-depth ratio and the speed of construction hollow core slabs are utilised in a large number of commercial buildings. In order to carry the services to the upper floors an opening must be made within the prestressed slab. Cutting an opening in a prestressed slab has significant effects on the structural behaviour of the slab and can considerably reduce the ultimate capacity of the slab.

This paper outlines the limited available guidance …

Reinforced Concrete Deterioration Of A 100 Year Old Structure In A Marine Environment, Ross O'Donovan

Theses

The current study investigates the deterioration of a 100 year old bridge located in a harsh marine environment. Constructed in 1908 - 1909 the Mizen Head Footbridge was one of the oldest reinforced concrete bridges in Ireland. The demolition of the bridge in 2009 provided a unique opportunity to examine its service life and to extract samples for analysis and investigation. A review of the construction of the bridge, and its maintenance history are presented, with a view to analysing their influence on the behaviour of the concrete.

Reinforcement corrosion due to chloride attack was identified. A focused study indicates …

Investigation Of Wastewater Treatment Plant Sustainability Potential In Terms Of Resource Recovery Essentials, Aoife Moloney

Theses

This thesis aims to explore the sustainability potential which exists in Wastewater Treatment Plants (WWTP's); particularly focusing on nutrient, energy, and water recovery and reuse. The core of the research will focus on the establishment of a sustainable Resource Recovery Treatment Plant (RRTP) plan for Limerick Main Drainage (LMD) WWTP, and potentially utilising this as a case study plant which could act as a foundation example within the sector.

There is a genuine need to investigate more sustainable options in wastewater treatment (WWT); increasing energy and sludge management costs are a real issue for non-sustainable WWTP's given that thousands of …

Risk Assessment Of Driving Safety In Long Scaled Bridge Under Severe Weather Conditions, Shengdi Chen

USF Tampa Graduate Theses and Dissertations

Weather conditions have certain impacts on roadway traffic operations, especially traffic safety. Bridges differ from most surface streets and highways in terms of their physical properties and operational characteristics. This research assess the driving risk under different weather conditions through focus group firstly, then it develops a multi-ordered discrete choice model that is used to analyze and evaluate driving risks under both single and dual weather conditions. The data is derived from an extensive questionnaire survey in Shanghai. And the questionnaire includes those factors related to roadway, drivers, vehicles, and traffic that may have significant impacts on traffic safety under …

A Study On Lane-Change Recognition Using Support Vector Machine, Weiping Deng

USF Tampa Graduate Theses and Dissertations

This research focuses primary on recognition of lane-change behaviors using support vector machines (SVMs). Previous research and statistical results show that the vast majority of motor vehicle accidents are caused by driver behavior and errors. Therefore, the interpretation and evaluation of driver behavior is important for road safety analysis and improvement. The main limit to understanding driver behavior is the data availability. In particular, a full-scale lane-change data set is difficult to collect in a real traffic environment because of the safety and cost issues. Considering the data demands of the recognition model development and the obstacles of field data …

Geometric Optimization Of Retroreflective Raised Pavement Markers, Lukai Guo

USF Tampa Graduate Theses and Dissertations

As the field service life of retroreflective raised pavement marker (RRPM) is much shorter than expected, it is necessary to identify the causes and thus improve the RRPM structural design to mitigate the main failure modes, such as poor retention from pavements, structural damage, and loss of retroreflectivity. One strategy for extending RRPM service life is to enhance RRPM geometric characteristics to decrease critical stresses in markers. The main purpose of this thesis is to analyze the relationship between stresses, failure modes, and RRPM profiles. Based on this research, some measures are suggested in order to avoid corresponding failure modes …

Flexible Urban Water Distribution Systems, Seneshaw Amare Tsegaye

USF Tampa Graduate Theses and Dissertations

With increasing global change pressures such as urbanization and climate change, cities of the future will experience difficulties in efficiently managing scarcer and less reliable water resources. However, projections of future global change pressures are plagued with uncertainties. This increases the difficulty in developing urban water systems that are adaptable to future uncertainty.

A major component of an urban water system is the distribution system, which constitutes approximately 80-85% of the total cost of the water supply system (Swamee and Sharma, 2008). Traditionally, water distribution systems (WDS) are designed using deterministic assumptions of main model input variables such as water …

Environmental Implications Of Pavements: A Life Cycle View, Bin Yu

USF Tampa Graduate Theses and Dissertations

Environmental aspect of pavement, unlike its economic counterpart, is seldom considered in the theoretical study and field practices. As a highly energy and material intensive infrastructure, pavement has great potential to contribute to the environment protection, which, in root, depends on the in-depth understanding of the environmental impacts, holistically and specifically. A life cycle assessment (LCA) model is used to fulfill the goal.

This research firstly carried out extensive literature review of LCA studies on pavement to identify the major research gaps, including: incompleteness of the methodology, controversy of the functional unit, and unawareness of feedstock energy of asphalt, etc. …

Prediction Of The Performance Of A Flexible Footing On A Stone-Column Modified Subgrade, Justin Callahan

USF Tampa Graduate Theses and Dissertations

When foundations are designed on weak clay layers, it is a common practice to modify the subgrade by installing stone columns. Currently used methods for determining the level of ground modification, represented by the percentage of soil replaced (replacement ratio), assume a rigid foundation. These analytical methods provide the designer with the potential settlement reduction based on the compressibility parameters of the subgrade and the replacement ratio. The deficiencies of these methods are the assumption of rigidity of the foundation and the consideration of the settlement reduction as the only design criterion. Furthermore, they do not consider the effects that …

Effect Of Cement Chemistry And Properties On Activation Energy, Andre J. Bien-Aime

USF Tampa Graduate Theses and Dissertations

The objective of this work is to examine the effect of cement chemistry and physical properties on activation energy. Research efforts indicated that time dependent concrete properties such as strength, heat evolution, and thermal cracking are predictable through the concept of activation energy. Equivalent age concept, which uses the activation energy is key to such predictions. Furthermore, research has shown that Portland cement concrete properties are affected by particles size distribution, Blaine fineness, mineralogy and chemical composition. In this study, four Portland cements were used to evaluate different methods of activation energy determination based on strength and heat of hydration …

Spatial Transferability Of Activity-Based Travel Forecasting Models, Sujan Sikder

USF Tampa Graduate Theses and Dissertations

Spatial transferability of travel forecasting models, or the ability to transfer models from one geographical region to another, can potentially help in significant cost and time savings for regions that cannot invest in extensive data-collection and model-development procedures. This issue is particularly important in the context of tour-based/activity-based models whose development typically involves significant data inputs, skilled staff, and long production times. However, most literature on model transferability has been in the context of traditionally used trip-based models, particularly for linear regression-based trip generation and logit-based mode choice models, with little evidence on the transferability of activity-based models and that …