Engineering Commons^™

Predicting The State Of Health Of Samsung 25r Lithium Ion Batteries, Matthew O'Donnell

Open Access Master's Theses

This thesis may contain material at the Controlled Unclassified Information (CUI) level. The full document cannot be released.

Fluid Pathways For Enhanced Mass Transfer In The Micro Regime: Applications In Novel Pumpless Redox Flow Cell And Zinc Finger Protein-Based Dna Detection, Shaikh Al Mahmud Bhuiyan

Theses and Dissertations--Mechanical and Aerospace Engineering

Precise fluid transport through microscale geometries can help optimize electrochemical and biochemical processes by maximizing the mass transfer rate of reactants. By introducing intricate structural features inside microchannels, it is possible to manipulate the fluid motion and direct the flow towards any surface of interest. In this study, we have demonstrated that rationally designed fluid pathways can improve the performance of electrochemical and biochemical systems.

The emergence of additive manufacturing has enabled rapid fabrication of robust structures with intricate features to guide fluid motion. However, their application in nonaqueous electrochemical systems has been limited due to their interaction with organic …

Chondrogenic And Chondroprotective Response Of Composite Collagen I/Ii-Hyaluronic Acid Scaffolds Within An Inflammatory Osteoarthritic Environment, Carly M. Battistoni, Javier Munoz Briones, Douglas K. Brubaker, Alyssa Panitch, Julie C. Liu

School of Chemical Engineering Faculty Publications

Inflammation plays a key role in cartilage damage that occurs in osteoarthritis (OA). However, in vitro assessments of tissue-engineered constructs for cartilage regeneration generally do not consider their performance in the presence of inflammation. In this work, the chondrogenic differentiation potential of mesenchymal stromal cells (MSCs) was evaluated in the presence of both chondrogenic factors and inflammatory cytokines, and cartilage formation, degradative response, and inflammatory response were characterized. The addition of cytokines reduced cartilage production, increased cell proliferation, and resulted in an increase in inflammatory markers. Incorporation of hyaluronic acid (HA) had little impact on both collagen fibril microstructure and …

Microwave-Assisted Reduction Of Critical Metal Oxides From E-Waste Mixture, Kurundu Shavinka Jayasekera

Graduate Theses, Dissertations, and Problem Reports (ETD)

The efficient recovery of critical metals such as tantalum (Ta), manganese (Mn), gallium (Ga), and indium (In) from electronic waste (e-waste) is essential for resource sustainability and environmental protection. This research uses microwave-assisted treatment to investigate the carbothermal reduction of these four specific metals from their oxides in a simulated e-waste mixture, with carbon black serving as both a microwave coupling and reduction agent. Microwave processing is used specifically because it offers a rapid and energy-efficient alternative to conventional thermal methods, with the benefits of intrinsic heating and selective heating of materials. The first experiments centered on understanding the effects …

Development And Characterization Of Polysaccharide-Based Controlled Drug Delivery Platforms, Amanda Pepler

Open Access Dissertations

Drug delivery research focuses on overcoming challenges in patient treatment. Most therapeutics are delivered systemically through oral or intravenous routes. However, these administration methods are often inefficient due to therapeutic hydrophobicity, poor bioavailability, and liver metabolic clearance, necessitating frequent dosing. When treatment plans require frequent dosing, patients experience significant fluctuations in therapeutic concentration in the bloodstream, which can increase adverse side effects. These factors contribute to low patient compliance. Therefore, the core focus of drug delivery research is to develop new administration routes for therapeutics. Drug delivery systems (DDS) that can target therapeutics to a localized region offer advantages over …

Valorizing Municipal Solid Waste For Sustainable Aviation Fuel And Polyhydroxyalkanoate Bioplastics: Pyrolysis And Microbial Pathways, Emon Das

Theses and Dissertations--Biosystems and Agricultural Engineering

The escalating global burden of municipal solid waste (MSW), projected to reach 3.88 billion tons annually by 2050, calls for innovative valorization strategies to mitigate environmental impacts and promote a circular bioeconomy. This thesis investigates the conversion of MSW into two high-value products: sustainable aviation fuel (SAF) and polyhydroxyalkanoate (PHA) bioplastics. Chapter one presents comprehensive physicochemical characterization and pyrolysis-GC/MS analysis of MSW feedstocks. The physicochemical results reveal that densification enhances handling and storage properties, while pyrolysis-GC/MS analysis indicates that plastic-rich MSW streams produce bio-oils with favorable hydrocarbon profiles suitable for SAF production, potentially contributing to decarbonization efforts in the aviation …

How Many Passes Does It Take? An Investigation To Determine The Optimal Number Of Liposome Extrusion Cycles, Kasey Piper

Honors Theses

Liposomes are lipid-based nanoparticles with significant applications in drug delivery and membrane research. One of the most common methods for fabricating liposomes of specific sizes is membrane extrusion, where liposomes are passed through porous membranes to reduce their size. The precise number of passes needed and the factors influencing this process remain unclear. This thesis investigates the relationship between the number of passes through a track-etched polycarbonate membrane and size and lamellarity of extruded liposomes with a focus on lipid type (DOPC, DMPC, Soy PC), membrane pore size (50, 100, 200, 400 nm), and the effect of freeze-thaw cycling. To …

Statistical Investigation Of Gypsum Crystallization Kinetics, Azmain A. Akash

LSU Master's Theses

Gypsum, a naturally occurring mineral salt, is frequently encountered in industrial processes such as seawater desalination and power plant cooling. Over the years, significant effort has been devoted to controlling the crystallization of gypsum through various chemical approaches, including acidification, chelating agents, and antiscalant polymers. Nevertheless, the cost associated with chemical treatments may be reduced by incorporating physical operational strategies to complement chemical methods in regulating gypsum crystallization.

This study systematically examines the comparative roles of chemical and physical entropy in the gypsum crystallization process to elucidate their respective influences on gypsum growth kinetics. Chemical entropy is manipulated by adjusting …

Valorization Of Biomass Derivatives To Monomers By M-Mox Catalytic Hydrogenation & Hydrodeoxygenation, William Steere, Samir Castilla-Acevedo, Ben Auer, John Styers, Alan Allgeier

UNH URC Open (2026 and after)

With increasing concern regarding global warming contributions by fossil fuels in petrochemical production, the potential use of biomass-derived molecules to serve as a more eco-friendly feedstock has grown in popularity. Specifically, sebacic acid, a versatile chemical used to produce nylons, plasticizers, and lubricants, has the potential to be obtained from bio-renewable feedstocks and alleviate environmental drawbacks from fossil fuel petrochemical production. Our research validates the catalytic conversion of the biomass-derived 2,2’-bifuran 5,5’-dicarboxylate (BFDCM) to sebacic acid (SA), through M-MO_x catalyzed hydrogenation and hydrodeoxygenation. Catalytic activity tests were conducted for four different Pd-supported catalysts (C, Al₂O₃, …

Extraction And Separation Of Metal Cations From Synthetic Acidic Solutions Using Emulsion Liquid Membrane, Nouhaila Filali

Masters Theses

The work is organized into two main papers supported by experimental and comparative studies using Emulsion Liquid Membrane (ELM) systems. The first paper explores the individual extraction of heavy metals (Cd, Cr, As, Ni) from synthetic phosphoric acid using Alamine 336 and D2EHPA as carriers. Alamine 336 achieved the highest extraction efficiency (>90%) and stability, offering a promising route to reduce toxic impurities in fertilizer-grade acid. The second paper examines the selective separation of Ni2+ and Co2+ from various acidic solutions using the ELM configuration. Systematic variation of carriers, stripping agent and feed acidity, clarified transport mechanisms and stability, …

A Pyrrole Modified 3,4-Propylenedioxythiophene Conjugated Polymer As Hole Transport Layer For Efficient And Stable Perovskite Solar Cells, Yuanhao Tang, Ke Ma, Wenhao Shao, Yoon Ho Lee, Ashkan Abtahi, Jiaonan Sun, Hanjun Yang, Aidan H. Coffey, Harindi R. Atapattu, Mustafa Ahmed, Qixuan Hu, Wenzhan Xu, Raunak Dani, Limei Wang, Chenhui Zhu, Kenneth R. Graham, Jianguo Mei, Letian Dou

Chemical and Materials Engineering Faculty Publications

Despite the outstanding electric properties and cost-effectiveness of poly- (3,4-ethylenedioxythiophene) (PEDOT) and its derivatives, their performance as hole transport layer (HTL) materials in conventional perovskite solar cells (PSCs) has lagged behind that of widely used spirobifluorene-based molecules or poly(triaryl amine). This gap is mainly from their poor solubility and energy alignment mismatch. In this work, the design and synthesis of a pyrrole-modified HTL (PPr) based on 3,4-propylenedioxythiophene (ProDOT) are presented for efficient and stable PSCs. As a result of the superior defects passivation ability, excellent contact with perovskite, enhanced hole extraction, and high hydrophobicity, the unencapsulated PPr-based PSCs showed the …

Analysis Of Tar And Oil Derived From Pyrolysis And Copyrolysis Of Waste Plastics And Biomass, Anitha Shankaralinge Gowda, Dimitrios Karadimas, Jeffrey Seay

Chemical and Materials Engineering Faculty Publications

Pyrolysis has been proposed as a potential technology for managing the growing volume of plastic waste generated worldwide. Co-pyrolysis of plastic waste with biomass is a promising technology for generating fuel and chemical products. However, this process generates tar as a waste product. The chemical properties of this tar have yet to be thoroughly analyzed. This study presents the results of gas chromatography–mass spectrometry (GC–MS), Fourier-transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA) of oil and tar obtained from the pyrolysis of pure plastics including high-density polyethylene (HDPE), low-density polyethylene (LDPE), polyethylene (PE), polystyrene (PS), and plastic-biomass mixtures. GC–MS analysis …

Membrane Filtration Of Nanoscale Biomaterials: Model System And Membrane Performance Evaluation For Aav2 Viral Vector Clarification And Recovery, Mara Leach, Kearstin Edmonds, Emily Ingram, Rebecca E. Dutch, Ranil Wickramasinghe, Malgorzata Chwatko, Dibakar Bhattacharyya

Chemical and Materials Engineering Faculty Publications

The growing demand for viral vectors as nanoscale therapeutic agents in gene therapy necessitates efficient and scalable purification methods. This study examined the role of nanoscale biomaterials in optimizing viral vector clarification through a model system mimicking real AAV2 crude harvest material. Using lysed HEK293 cells and silica nanoparticles (20 nm) as surrogates for AAV2 crude harvest, we evaluated primary (depth filters) and secondary (membrane-based) filtration processes under different process parameters and solution conditions. These filtration systems were then assessed for their ability to recover nanoscale viral vectors while reducing DNA (without the need for endonuclease treatment), protein, and turbidity. …

Fundamental And Application Of Co-Assembly Of Peptides And Proteins: Experiment And Computation, Newton A. Ihoeghian, Qing Shao

Chemical and Materials Engineering Faculty Publications

Peptides and proteins can co-assemble into various nanostructures based on complementary non-covalent interactions such as electrostatic forces, hydrogen bonding, and hydrophobic associations. These co-assemblies create a design space of functional materials for a wide spectrum of energy, environmental, and biomedical applications. This review focuses on the fundamentals and applications of three co-assembling systems: ultra-short peptides, peptides, and proteins. We will present and discuss experimental studies demonstrating applications in drug delivery, tissue engineering, and biomaterials development. We will also discuss the contribution of computational research, including molecular dynamics simulations and machine learning, to enhance our understanding of assembly mechanisms. Integrating experimental …

Metathesis Or Isomerization: Counteranion Directed Reactivity Of Grubbs I, Paul D. Miller, Joe B. Calkins, Craig A. Bayse, Trandon A. Bender

Chemistry & Biochemistry Faculty Publications

Catalytic isomerization of alkenes has garnered interest for many years, but there are remaining challenges when it comes to thermodynamic selectivity and uncontrolled isomerization. Nonbiased substrates, be it sterically or thermodynamically, remain challenging for many catalysts, with a few examples available in the more modern literature. Herein, we present the controlled isomerization of linear alkenes with a cocatalytic mixture of commercially available catalyst and reagents: Grubbs I, tris(pentafluorophenyl)borane, and triethylsilane. DFT calculations indicate that an observed alkylidyne hydride intermediate is in rapid equilibrium with an alkylidene that binds the alkene substrate. This combination results in a pi-acidic metal and a …

Supercapacitors With Cotton Shell-Derived Activated Carbons And Porous Polymer Electrolyte Films, Saurabh Singh, Yulin Zhang, S. A. Hashmi, Fuqian Yang

Chemical and Materials Engineering Faculty Publications

Some of the well-known challenges in the field of supercapacitors (SCs), or more specifically, electrical double-layer capacitors (EDLCs), such as low energy density and high cost, have proven to be major barriers to their widespread market success despite having some excellent electrochemical merits such as high-power density and good cyclic stability. In this work, efforts have been made to overcome these gaps and eventually enhance the performance of EDLCs via a cost-effective and eco-friendly approach. To fabricate these EDLCs, a bio-waste, namely, cotton-shell-derived activated carbons (ZnACs) (activated with ZnCl2), was used in a mass ratio of 1 : 2 for …

Improvement Of Cellular Pattern Organization And Clarity Through Centrifugal Force, Lauren E. Mehanna, James D. Boyd, Shelley Remus-Williams, Nicole M. Racca, Dawson P. Spraggins, Martha E. Grady, Brad J. Berron

Chemical and Materials Engineering Faculty Publications

Rapid and strategic cell placement is necessary for high throughput tissue fabrication. Current adhesive cell patterning systems rely on fluidic shear flow to remove cells outside of the patterned regions, but limitations in washing complexity and uniformity prevent adhesive patterns from being widely applied. Centrifugation is commonly used to study the adhesive strength of cells to various substrates; however, the approach has not been applied to selective cell adhesion systems to create highly organized cell patterns. This study shows centrifugation as a promising method to wash cellular patterns after selective binding of cells to the surface has taken place. After …

Integrating Protein Language Model And Molecular Dynamics Simulations To Discover Antibiofouling Peptides, Ibrahim A. Imam, Shea Bailey, Duolin Wang, Shuai Zeng, Dong Xu, Qing Shao

Chemical and Materials Engineering Faculty Publications

Antibiofouling peptide materials prevent the nonspecific adsorption of proteins on devices, enabling them to perform their designed functions as desired in complex biological environments. Due to their importance, research on antibiofouling peptide materials has been one of the central subjects of interfacial engineering. However, only a few antibiofouling peptide sequences have been developed. This narrow scope of antibiofouling peptide materials limits their capacity to adapt to the broad spectrum of application scenarios. To address this issue, we searched for antibiofouling peptides in the vast sequence pool of the microbiome library using a combination of deep learning-based high-throughput search and molecular …

Clarifying The Role Of Η-Phase With Varying Chemistry On Localised Corrosion Of A Cu-Containing 7xxx Al-Alloy By Quasi-In-Situ Tem, S. K. Kairy, Y. Wu, S. Turk, A. Shekhter, Rudolph Buchheit, N. Birbilis

Chemical and Materials Engineering Faculty Publications

Quasi-in-situ transmission electron microscopy was employed to study dissolution associated with η-phase (Mg(Zn,Al,Cu)₂) precipitates in a Cu-containing 7xxx Al-alloy. Two distinct η-phase chemistries, with Cu to (Zn+Mg+Al) ratios ∼0.12 and ∼0.2, were studied in 0.01 M NaCl at pH 6 and 2. In near-neutral NaCl, both η-phase precipitates exhibited ‘duplex’ behaviour, i.e., they were primarily more noble with respect to the surrounding Al-matrix, causing matrix dissolution, and simultaneously established nanoscopic active sites within the noble precipitate itself by generating nanoscale pits. Conversely, η-phase precipitates rapidly dealloyed in acidic NaCl, forming nocrystalline Cu remnants containing twins, which subsequently caused …

Enhancing Intrinsic Ductility In Vnbmotaw High Entropy Alloy: A Combinatorial Investigation With Experimental Evaluation Of Theoretical Predictions, Taohid Bin Nur Tuhser, Ian Stewart Winter, Daryl Chrzan, Thomas John Balk

Chemical and Materials Engineering Faculty Publications

The application of refractory high entropy alloys (RHEAs) as engineering materials has been hindered by their poor inherent ductility. In this study, a novel approach combining thin film combinatorial screening with fragmentation testing was employed to identify intrinsically ductile alloy compositions. Inspired by the physics-based intrinsic ductility parameter, the ‘χ-parameter,’ we investigated the replacement of group VI elements (W/Mo) with group V elements (V, Nb, Ta) in the VNbMoTaW system. Conventional combinatorial analyses, including composition, phase, and hardness assessments, were conducted across a wide range of non-equiatomic configurations. The results revealed a broad compositional space favoring a single-phase body-centered cubic …

Modeling Ion-Specific Effects In Polyelectrolyte Brushes: A Modified Poisson-Nernst-Planck Model, William J. Ceely, Marina Chugunova, Ali Nadim, James D. Sterling

Business and Information Technology Faculty Research & Creative Works

Polyelectrolyte brushes consist of a set of charged linear macromolecules, each tethered at one end to a surface. An example is the glycocalyx which refers to hair-like negatively charged sugar molecules that coat the outside membrane of all cells. We consider the transport and equilibrium distribution of ions and the resulting electrical potential when such a brush is immersed in a salt buffer containing monovalent cations (sodium and/or potassium). The Gouy-Chapman model for ion screening at a charged surface captures the effects of the Coulombic force that drives ion electrophoresis and diffusion but neglects non-Coulombic forces and ion pairing. By …

The Antibiofilm Efficacy Of Copper And Zinc-Enhanced Borate Bioactive Glasses On Polymicrobial Biofilms, Sarah Fakher, David J. Westenberg

Biological Sciences Faculty Research & Creative Works

Healthcare-acquired infections (HAIs) are a significant global challenge driven by biofilm-forming pathogens. Polymicrobial biofilms, involving interactions between multiple microbial species, exacerbate treatment difficulties due to their enhanced resistance to antimicrobial therapies. Borate bioactive glasses (BBGs) are an emerging class of biomaterials that have attracted significant interest in infection control. The incorporation of copper and zinc into the BBG matrix can effectively disrupt biofilm formation and bacterial colonization. This study investigates the antibiofilm efficacy of copper and zinc-doped BBGs against polymicrobial biofilms formed by S. epidermidis, E. coli, and P. aeruginosa. Using static and dynamic biofilm models, BBGs were applied through …

Nanotube Spectral Fingerprinting And Machine Learning For Optimized Bioimaging/Sensing And Disease Detection Applications In Als, Rodrigo Monroy Lopez

Open Access Master's Theses

Single-walled carbon nanotubes (SWCNTs) possess unique physicochemical and optical properties that make them ideal candidates for biomedical imaging, biosensing, and disease diagnostics. This thesis explores the potential of SWCNT-based spectral fingerprinting combined with ML (Machine Learning) algorithms to optimize bioimaging, disease detection and prediction, with a specific focus on differentiating between healthy and amyotrophic lateral sclerosis (ALS) lymphoblastic patient samples. By functionalizing SWCNTs with single-stranded DNA, we enhance their stability and target specificity, enabling their application in serum patient samples.

A comprehensive spectral analysis of DNA-SWCNTs was conducted using near-infrared fluorescence spectroscopy and other characterization techniques, including UV-Vis-absorption spectroscopy. The …

Ground Testing Of A Magnetic-Electrostatic Separation System For Lunar Regolith Beneficiation, Peter Bachle, Charles Wood, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

The separation of lunar regolith by mineral composition and size category is useful forin-situ resource utilization (ISRU). The research presented herein discusses the designing and development of equipment that has the potential to separate lunar regolith into aluminum, iron-titanium, and magnesium-iron ores. Along with the metal ore separation, this equipment shows the potential to separate regolith by size categories. The combined effect of these separation methods generates output that is valuable to subsequent use in metal and oxygen extraction, additive manufacturing, and regolith sintering processes. The designed equipment uses a dual-strength magnet system with N42 and N52 neodymium magnets for …

Investigation Of Dynamic Adsorption And Desorption Of Polymer Nanogel In Porous Media Through Microfluidics, Junchen Liu, Fuqiao Bai, Abdulaziz A. Almakimi, Mingzhen Wei, Xiaoming He, Ibnelwaleed A. Hussein, Baojun Bai

Mathematics and Statistics Faculty Research & Creative Works

Understanding the transport and retention of elastic nanogel and microgel particles in porous media has been a significant research subject for decades, essential to the application of enhanced oil recovery (EOR). However, a lack of dynamic adsorption and desorption studies, in which the kinetics in porous media are seldom investigated, hinders the design and application of polymer nanogel in underground porous media. In this work, we visualized and quantified the transport and dynamic adsorption of polymer nanogel in 3D glass micromodels that were manufactured by packing glass beads in capillaries. Calibrating the linearity of fluorescence intensity to concentration, we calculated …

Effects Of Chain Length, Saturation, And Bases On Saponification, Sarah Fenik

Williams Honors College, Honors Research Projects

This project will analyze the effects of chain length and saturation of fatty acids on saponification processes, as well as the effects of the base used in the reaction. Stearic acid, lauric acid, and oleic acid will be used for the fatty acid comparisons, and sodium hydroxide and potassium hydroxide will be used for the base comparisons. Stearic acid is considered a long chain fatty acid, while lauric acid is considered a short chain fatty acid. Oleic acid is a monounsaturated fatty acid. Five soap products are be made: sodium stearate, sodium laurate, sodium oleate, potassium stearate, and potassium oleate. …

Anti-Icing Properties Of 3d-Printed Superhydrophobic Surfaces, Nathan Kling

Williams Honors College, Honors Research Projects

This project aims to investigate how textured microscopic surfaces can reduce ice adhesion, utilizing 3D-printed resin materials. By varying the size and shape of these surface imperfections, the research seeks to identify configurations that minimize ice formation and facilitate easier ice removal. The trapped air between the imperfections is expected to hinder water droplet adhesion, promoting detachment through gravity or motion. The study’s applications could extend to preventing icing on power lines, roads, and aircraft. Methodologically, the project will build on prior research, applying water to textured surfaces under controlled temperature conditions to assess ice formation and removal efficiency. Key …

Corrosion Of Pipes In Soil Under Cathodic Protection, Ashley Chow

Williams Honors College, Honors Research Projects

This research project focuses on understanding how various soil properties affect the corrosion of buried pipelines that are protected by cathodic protection (CP) systems. Specifically, the study seeks to evaluate key soil characteristics, including resistivity, moisture content, and pH levels to determine their influence on the efficiency of CP systems in mitigating corrosion. Through controlled laboratory experiments, carbon steel specimens were exposed to a range of simulated soil conditions to mimic real-world environments. Corrosion rates were assessed using advanced electrochemical techniques, such as linear polarization resistance (LPR) and Tafel slopes, along with traditional mass loss methods. The primary objectives of …

Prediction Of Glass Transition Temperature Of Polymers Using Structure-Based Models, Nicholas Wolfe

Williams Honors College, Honors Research Projects

The focus for this study is prediction of glass transition temperatures of polymers using machine learning models. The preprocessing of the data included the generation of descriptors, the scaling of the data, the principal component analysis for dimensionality reduction, and the clustering of the data. Three methods of property predictions were utilized including Linear Regression, Random Forest, and a Feedforward Neural Network. The dataset consisted of over 7000 polymers each with their respective glass transition temperatures. This study found that the Random Forest model returned the best results followed by the Feedforward Neural Network then the Linear Regression model. Each …

Qualitative Analysis Of Surface Modification On Wiffleball Aerodynamics, Cole Lanni

Williams Honors College, Honors Research Projects

This project investigated how surface modifications to a Wiffleball affect its aerodynamic behavior, particularly its vertical and horizontal movement when thrown. The study tested the hypothesis that altering surface texture through cutting or sanding would influence airflow and pressure differentials, thereby changing the ball's movement. Six ball conditions: including unmodified, sanded, and various cut patterns were tested using a pitching machine in a controlled indoor environment. Each variation was pitched ten times, and movement was analyzed through measurements of contact points on posterboards and performing statistical testing, specifically ANOVA with Post Hoc analysis. Results indicated that surface modifications significantly increased …