Engineering Commons^™

A Mathematical Model Of A Control Systems Hypothesis Of N-Methyl-D-Aspartate-Receptor-Mediated Ethanol Dependence And Withdrawal Dynamics, Carlos Gutierrez

Theses and Dissertations

The biochemical effects of ethanol on the human brain are manifested through many neurological pathways. Chronic exposure to the depressant has been shown to result in physical dependence. Subsequent cessation results in withdrawal symptoms such as seizures and both short- and long-term changes in neurological activity. One of the primary conduits implicated in the pathways of ethanol dependence and withdrawal is the detection of glutamate via N-methyl-D-aspartate (NMDA) receptors (NMDARs). Ethanol molecules inhibit these receptors, and consequent NMDA-induced glutamatergic changes can result in dependence on ethanol in order to sustain normal brain function. This study considers the relocation control of …

Matrix Compliance And The Regulation Of Cytokinesis, Savitha Sambandamoorthy, Shomita Mathew-Steiner, Scott Varney, Jonathan M. Zuidema, Ryan J. Gilbert, Livingston De Van Water, Susan E. Laflamme

Chemical and Biochemical Engineering Faculty Research & Creative Works

Integrin-mediated cell adhesion to the ECM regulates many physiological processes in part by controlling cell proliferation. It is well established that many normal cells require integrin-mediated adhesion to enter S phase of the cell cycle. Recent evidence indicates that integrins also regulate cytokinesis. Mechanical properties of the ECM can dictate entry into S phase; however, it is not known whether they also can affect the successful completion of cell division. To address this issue, we modulated substrate compliance using fibronectin-coated acrylamide-based hydrogels. Soft and hard substrates were generated with approximate elastic moduli of 1600 and 34,000 Pascals (Pa) respectively. Our …

The Role Of Environmental Dynamics In The Emergence Of Autocatalytic Networks, Joe Fusion

Dissertations and Theses

For life to arise from non-life, a metabolism must emerge and maintain itself, distinct from its environment. One line of research seeking to understand this emergence has focused on models of autocatalytic reaction networks (ARNs) and the conditions that allow them to approximate metabolic behavior. These models have identified reaction parameters from which a proto-metabolism might emerge given an adequate matter-energy flow through the system. This dissertation extends that research by answering the question: can dynamically structured interactions with the environment promote the emergence of ARNs? This question was inspired by theories that place the origin of life in contexts …

Optimum 3d Matrix Stiffness For Maintenance Of Cancer Stem Cells Is Dependent On Tissue Origin Of Cancer Cells, Esmaiel Jabbari, Samaneh K. Sarvestani, Leily Daneshian, Seyedsina Moeinzadeh

Faculty Publications

Introduction

The growth and expression of cancer stem cells (CSCs) depend on many factors in the tumor microenvironment. The objective of this work was to investigate the effect of cancer cells’ tissue origin on the optimum matrix stiffness for CSC growth and marker expression in a model polyethylene glycol diacrylate (PEGDA) hydrogel without the interference of other factors in the microenvironment.

Methods

Human MCF7 and MDA-MB-231 breast carcinoma, HCT116 colorectal and AGS gastric carcinoma, and U2OS osteosarcoma cells were used. The cells were encapsulated in PEGDA gels with compressive moduli in the 2-70 kPa range and optimized cell seeding density …

Secondary Organic Aerosol Formation From The Β-Pinene+No3 System: Effect Of Humidity And Peroxy Radical Fate, C. M. Boyd, J. Sanchez, L. Xu, Alexis J. Eugene, T. Nah, W. Y. Tuet, Marcelo I. Guzman, N. L. Ng

Chemistry Faculty Publications

The formation of secondary organic aerosol (SOA) from the oxidation of β-pinene via nitrate radicals is investigated in the Georgia Tech Environmental Chamber (GTEC) facility. Aerosol yields are determined for experiments performed under both dry (relative humidity (RH) < 2 %) and humid (RH = 50 % and RH = 70 %) conditions. To probe the effects of peroxy radical (RO₂) fate on aerosol formation, "RO₂ + NO₃ dominant" and "RO₂ + HO₂ dominant" experiments are performed. Gas-phase organic nitrate species (with molecular weights of 215, 229, 231, and 245 amu, which likely correspond to molecular formulas of C₁₀H₁₇NO₄, C₁₀H₁₅NO₅, C₁₀H₁₇NO …

Platinum-Bismuth Bimetallic Catalysts: Synthesis, Characterization And Applications, Jose A. Saucedo Jr, Yang Xiao, Arvind Varma

The Summer Undergraduate Research Fellowship (SURF) Symposium

Bimetallic catalysts have been explored and shown to exhibit unique characteristics which are not present in monometallic catalysts. Platinum is well known as an effective catalyst for oxidation and reduction reactions, and it can be made more effective when bismuth is introduced as a promotor. Thus, the effectiveness of the Pt-Bi catalyst was demonstrated in prior work. What is not clear, however, is the mechanism behind the catalyst function; why addition of bismuth to platinum decreases deactivation and increases selectivity, and how effective would the Pt-Bi catalyst be in deoxygenation reactions? In this work, the effectiveness of different variations of …

Gold Nanoparticle Enhancements In Electroporation Mediated Dna And Rna Therapeutics, Shuyan Huang

Doctoral Dissertations

Nonviral gene delivery methods have been explored as the replacement of viral systems for their low toxicity and immunogenicity. However, they have yet to reach levels competitive to their viral counterparts. Electroporation figured prominently as an effective nonviral gene delivery approach for its balance on the transfection efficiency and cell viability, no restrictions of probe or cell type, and operation simplicity. The commercial electroporation systems have been widely adopted in the past two decades but still carry drawbacks associated with the high applied electric voltage, unsatisfied delivery efficiency, and/or low cell viability. What we did was to improve electroporation performance …

Swelling-Etching Characterization Of Copper (I) Oxide - Pdms For The Development Of Micro/Nano - Particles Composite Mems Corrosion Sensor, Abdoul Kader Maiga

Graduate Theses and Dissertations

The primary objective for this thesis is to contribute to the understanding of the oxide removal process for a corrosion sensing device. The goal for designing such a device is for monitoring corrosion on metallic structures. The sensing material (6.35mm x 1mm discs) of the device is composed of copper (I) oxide particles mixed in some polydimethylsiloxane (PDMS). The PDMS, “housing,” is meant for controlling the oxidation rate through the sensing material. A solvent was used to facilitate the etchant diffusion through the PDMS matrix. Toluene and acetic acid were the ideal solvent and etchant, respectively, for carrying out the …

Diamond Mems Biosensors: Development And Applications, Wenli Zhang

Doctoral Dissertations

This research focuses on the development a dielectrophoresis-enhanced microfluidic impedance biosensor (DEP-e-MIB) to enable fast response, real-time, label-free, and highly sensitive sensor for bacterial detection in clinical sample. The proposed design consists of application of dielectrophoresis (DEP) across a microfluidic channel to one of the impedance spectroscopy electrodes in order to improve the existent bacterial detection limits with impedance spectroscopy. In order to realize such a design, choice of electrode material with a wide electrochemical potential window for water is very important. Conventional electrode material, such as gold, are typically insulated for the application of DEP, and they fail when …

Investigating The Impact Of Cryogenic Carbon Capture On Power Plant Performance, Seyed M. Safdarnejad, L. Kennington, Larry Lin Baxter, John Hedengren

Faculty Publications

Cryogenic Carbon Capture (CCC) is a CO2 mitigation process that can be integrated into existing baseline and load following fossil-fueled power plants. This process consumes less energy than conventional chemical absorption and includes energy storage capability. The CCC process has a fast response time to load changes to allow higher utilization of intermittent renewable power sources to be used at a grid-scale level in the power sector. The impact of the CCC process on the performance and operating profit of a single fossil-fueled power generation unit is studied in this paper. The proposed system (power production from wind, coal, and …

Using Peptoids To Build Robust, Efficient Microarray Systems, Dhaval Sunil Shah

Graduate Theses and Dissertations

Recent studies have shown microarrays to be indispensable for various biological applications, allowing for high-throughput processing and screening of biological samples such as RNA, DNA, proteins and peptides using a small sample volume (< 1 µL). Peptoids (poly-N-substituted glycine oligomers) can be used as a substitute for antibodies as capture molecules, as well as coatings for slides in antibody microarrays. The ease of synthesis of peptoids, high customizability with desired bioactivity, and speed of synthesis allows us to build a diagnostic system with a large dynamic range that can detect biomolecules from a minimal sample size. In this study, peptoid-based antibody mimics are designed to have both structural and functional features similar to those of antibodies, including a stable constant region (scaffolding) and a variable region for protein recognition. Peptoids previously screened via combinatorial library synthesis to be specific to bind Mdm-2 (mouse double minute 2 homolog) and GST (gluthathione S-transferase), have been synthesized. The protein recognition peptoids have been conjugated to PEG (polyethylene glycol) molecules with modified end groups; an amine group on one end that allows for immobilization and orientation on the slide, and an azide group on the other end that will allow for attachment to the peptoid through “click chemistry”. The number of capture molecules printed on the slides can be increased by making the available surface area of the slide larger via coating with microspheres. We have determined that partially water soluble peptoids that are also helical, can self-assemble into microspheres. Sequences have been developed that can consistently produce uniform microsphere coatings on slides that increase the overall surface area. A high surface area corresponds to a higher number of binding sites, and therefore a more sensitive system. The work done has shown that slides may be successfully coated in order to potentially improve the detection system.

Peptoid-Based Klvff Mimics: A Unique Approach To Alzheimer's Disease, James Phillip Turner

Graduate Theses and Dissertations

Alzheimer’s disease (AD) is the leading form of dementia worldwide. AD patients experience a slow, gradual cognitive decline that includes loss of memory and behavioral stability as the disease progresses. Surprisingly, AD is the sixth leading cause of death in the United States and has had a profound impact on the U.S. economy. Though there are medications to help improve the quality of life of diagnosed patients for a period of time, there is still no cure for AD. AD is characterized by the build-up of amyloid plaques that develop from the aggregation of the amyloid beta protein (Aβ) in …

Model Of A Tubular Perfusion Bioreactor Using Computational Fluid Dynamics., Matthew James Robeson 1991-

Electronic Theses and Dissertations

Through recent years, many novel bioreactor designs for tissue engineering have emerged. The Tubular Perfusion System (TPS) is one such bioreactor for bone and cartilage tissue engineering. The TPS is a perfusion type bioreactor, in which media flows through a bed of scaffold beads. The advantage of this system over similar designs is that it requires no special fabrication techniques and operates at low pressure. Experimental trials have shown increased osteoblastic differentiation and mineralization of bone tissue grown using the TPS versus static culture. The effectiveness of the TPS in promoting osteoblastic differentiation is believed to be due to enhanced …

Hydrothermal Catalytic Liquefaction And Deoxygenation Of Biomass For Renewable Fuel Production, Sergiy Popov

Civil & Environmental Engineering Theses & Dissertations

In recent years, sub- and supercritical water technologies received an increasing attention because of the numerous advantages they offer for biomass converting into biofuels. Water at elevated temperatures and pressures provides an ideal medium for chemical transformations. It serves as a reactant, reaction medium, and catalyst that helps biomass compounds undergo hydrolysis, depolymerization, dehydration, decarboxylation, and condensation/repolymerization reactions. Biomass is the fourth largest source of energy in the world after coal, oil, and natural gas that has the potential to provide the large scale substitution of hydrocarbon-based liquid transportation fuels and minimize the environmental issues. Biomass typically contains 40-60% oxygen. …

A Computational Study Of The Potential For Lng Tanker Polystyrene Foam Insulation Failure Under Fire Exposure, Jeffrey David Martinez

Graduate Theses and Dissertations

Liquefied natural gas is shipped across the oceans in large marine carriers. The carriers house the LNG using several different insulation systems. One of these systems involves large aluminum spheres insulated with polystyrene foam. Polystyrene foam is very susceptible to heat degradation. This raised issues as to the extent of possible insulation failure caused by a large ship fire. Experiments were done investigating the nature of polystyrene’s thermal degradation, notably by Brauman, Chen, and Matzinger and Butler. A large scale investigation was also performed by Sandia National Laboratory. However, computational modeling of the degradation was lacking. This work set out …

Plant-Level Dynamic Optimization Of Cryogenic Carbon Capture With Conventional And Renewable Power Sources, Seyed M. Safdarnejad, John Hedengren, Larry Lin Baxter

Faculty Publications

Increasing competitiveness of renewable power sources due to tightening restrictions on CO₂ emission from fossil fuel combustion is expected to cause a shift in power generation systems of the future. This investigation considers the impact of the Cryogenic Carbon Capture™ (CCC) process on transitional power generation. The CCC process consumes less energy than chemical and physical absorption processes and has an energy storage capability that shifts the parasitic loss of the CCC process away from peak hours. The CCC process responds rapidly to the variation of electricity demand and has a time constant that is consistent with the intermittent …

Electromagnetic Induction By Ferrofluid In An Oscillating Heating Pipe, John Gabriel Monroe, Erick S. Vasquez, Zachary S. Aspin, Keisha B. Walters, Matthew J. Berg, Scott M. Thompson

Chemical and Materials Engineering Faculty Publications

No abstract provided.

Synthesis Of Graphene Wrapped Li-Rich Layered Metal Oxide And Its Electrochemical Performance, Meng-Yan Hou, Ke Wang, Xiao-Li Dong, Yong-Yao Xia

Journal of Electrochemistry

In present work, lithium-rich layered transition metal oxide (LLO) was synthesized by a co-precipitation method in combination with a solid-state reaction. The graphene wrapped Li-rich layered oxide composite (LLO/Gra) was obtained by sintering the LLO/GO composite at 300 ^oC for 30 min in an air. The morphologies and the electrochemical performances were characterized by means of SEM, TEM, XRD, XPS, EIS and charge/discharge tests. The results indicated that the LLOe particles were uniformly wrapped with graphene. The resulting material exhibited better rate capability than that of pristine LLO since the wrapped graphene demonstrated the enhanced electronic conductivity. Accordingly, the …

Enhancing Stability Of Pem Fuel Cell Catalysts Via Support Changing, Xiao-Hong Xie, Zi-Dong Wei

Journal of Electrochemistry

The Pt/C catalyst with highly dispersed Pt nanoparticles supported on carbon has been widely used as the state-of the-art catalyst in proton exchange membrane fuel cells (PEMFCs), while the durability of Pt/C is one of the major barriers for large-scale applications of PEMFCs. Thus, enhancing the stability of Pt/C has been a hot issue in this field. In this review, we summarize the recent progress in enhancing the catalyst stability in the view of support material. The future prospects of the PEMFCs catalyst should focus on adopting more stable supports or strengthening the interactions between Pt and supports.

Pt/C Modified Proton Exchange Membrane For Improved Fuel Cell Performance, Zhi Cui, Chao Wang, Shui-Yun Shen, Feng-Jing Jiang, Jun-Liang Zhang

Journal of Electrochemistry

The property of proton exchange membrane greatly affects the performance of proton exchange membrane fuel cells (PEMFC). During the operation of a PEMFC, the water produced at the cathode, the water vapor from the humidified feed gas and the water migrated by electro-dragging will reach a balance in the membrane and determine the resistance of PEMFC, and thus affect the performance of PEMFC. Normally, the PEMFC performance strongly depends on the relative humidity of the feed gas, and the performance decreases at lower humidity as a result of lower proton conductivity of the membrane. In this paper, we proposed to …

Sacrificial Amphiphiles: Eco-Friendly Chemical Herders As Oil Spill Mitigation Chemicals, Deeksha Gupta, Bivas Sarker, Keith Thadikaran, Vijay John, Charles Maldarelli, George John

Publications and Research

Crude oil spills are a major threat to marine biota and the environment. When light crude oil spills on water, it forms a thin layer that is difficult to clean by any methods of oil spill response. Under these circumstances, a special type of amphiphile termed as “chemical herder” is sprayed onto the water surrounding the spilled oil. The amphiphile forms a monomolecular layer on the water surface, reducing the air–sea surface tension and causing the oil slick to retract into a thick mass that can be burnt in situ. The current best-known chemical herders are chemically stable and nonbiodegradable, …

The Electroreduction Of Carbon Dioxide On Porous Copper Nanoparticles, Monica Alisa Padilla

Chemical and Biological Engineering ETDs

Copper nanoparticles of porous, controlled structure were synthesized using the sacrificial support method (SSM). The precursor weight percent (wt%) of copper (Cu) and fumed silica (EH-5) was varied to determine the optimum ratio for this material. The precursors were reduced at i) 350°C in a 7% H2 atmosphere and ii) at 250°C in a 100% H2 atmosphere. The specific surface areas of the nanoparticles was measured by Brunauer-Emmett-Teller N2 absorption. The morphologies and widths of the nanoparticles were confirmed by imaging the nanoparticles by scanning electron microscopy (SEM). The bulk composition of the nanoparticles was determined by X-ray diffraction (XRD). …

Analysis Of Particle Transport And Deposition Of Micron-Sized Particles In A 90° Bend Using A Two-Fluid Eulerian–Eulerian Approach, Erick S. Vasquez, Keisha B. Walters, D. Keith Walters

Chemical and Materials Engineering Faculty Publications

Two-phase flows involving dispersed particle and droplet phases are common in a variety of natural and industrial processes, such as aerosols, blood flow, emulsions, and gas-catalyst systems. For sufficiently dilute particle/aerosol phases, a simplified one-way coupling is often assumed, in which the continuous primary phase is unaffected by the presence of the dispersed secondary phase and standard CFD methods can be applied. To predict the transport and deposition of the particle phase, typically a Lagrangian particle-tracking or Eulerian one-fluid/two-phase drift-flux approach is used. Here, a full two-fluid Eulerian modeling approach is presented for coarse particles (>1 μm), in which …

The Nucleation And Growth Of Nanoparticles For Heterogeneous Catalysis, Angelica Benavidez

Chemical and Biological Engineering ETDs

These studies investigate the nucleation and growth of nanoparticles and how their interaction with a support affects their reactivity as a heterogeneous catalyst. As capabilities in both synthesis methods and characterization methods advance, the use of nanoparticles and sub-nanometer species are more commonly used. These small particles introduce new factors that can cause differences in reactivity. Various catalyst synthesis methods are employed to deposit mono-dispersed particles on different oxide and carbon supports. Electron microscopy is used to study nanoparticle sintering and the careful tracking of individual particles gives insight into growth mechanisms. X-ray absorption spectroscopy measurements are used to characterize …

Morphology And Magnetic Properties Of Sulfonated Poly[Styrene-(Ethylene/Butylene)-Styrene]/Iron Oxide Composites, Sateesh K. Peddini, Huy N. Pham, Leonard Spinu, James L. Weston, David E. Nikles, Kenneth A. Mauritz

Faculty Publications

α-Fe₂O₃ structures were initiated in the sulfonated polystyrene block domains of poly[styrene–(ethylene/butylene)–styrene] (SEBS) block copolymers via a domain-targeted in-situ chemical precipitation method. The crystal structure of these particles was determined using wide-angle X-ray diffraction and selected area electron diffraction using a transmission electron microscope (TEM). TEM revealed that for less sulfonated SEBS (10 mole%), nanoparticles were aggregated with aggregate size range of 100–150 nm whereas for high sulfonation (16 and 20 mole% sSEBS) there were needle-like structures with length and width of 200–250 nm and 50 nm, respectively. Dynamic mechanical analyses suggest that initial iron oxide nanoparticle …

Advances In Catalyst Deactivation And Regeneration, Calvin H. Bartholomew, Morris D. Argyle

Faculty Publications

Catalyst deactivation, the loss over time of catalytic activity and/or selectivity, is a problem of great and continuing concern in the practice of industrial catalytic processes. Costs to industry for catalyst replacement and process shutdown total tens of billions of dollars per year. While catalyst deactivation is inevitable for most processes, some of its immediate, drastic consequences may be avoided, postponed, or even reversed through regeneration.

Analysis Of Neurite Outgrowth On Electrospun Fiber Scaffolds In The Presence Of Blebbistatin And Paclitaxel, A. R. D'Amato, N. J. Schaub, C. D.L. Johnson, J. Cardenas, R. J. Gilbert

Chemical and Biochemical Engineering Faculty Research & Creative Works

In an attempt to increase the rate of neurite extension from E9 chick embryo dorsal root ganglion (DRG) on electro spun fiber scaffolds we experimented with two drugs that have been used previously to affect neuronal growth. Blebbistatin and paclitaxel were added to DRG cultured on electro spun fibers in an attempt to increase the rate of neurite extension along fibrous scaffolds. Blebbistatin increased the length of neurites extending from the DRG explant in comparison to the drug-free control group. In contrast, paclitaxel completely eliminated all neurite extension from the DRG explant when compared to the control. A third treatment …

Initial Astrocyte Response To Electrospun Poly-L-Lactic Acid Fibers Of Varying Nanoscale Diameters, C. D.L. Johnson, J. M. Zuidema, G. P. Desmond, A. R. D'Amato, N. J. Schaub, R. J. Gilbert

Chemical and Biochemical Engineering Faculty Research & Creative Works

We hypothesized that fiber diameter within an electro spun fiber scaffold would affect astrocyte elongation and maturation. To examine the relationship, astrocytes were seeded on 400nm and 800nm diameter electro spun PLLA fibers. Immunohistochemistry was used to monitor cell morphology, and GLT-1 expression over the first 96 hours after seeding. The results indicate that astrocytes extended along the primary axis of the 800nm fibers more rapidly than astrocytes seeded on fibers of half the size. While GLT-1 was expressed diffusely throughout the surface of the astrocytes, elongated cell processes exhibited dense regions of GLT-1. These results show that 800nm fibers …

Astrocyte Response To Nanoscale Topography On Anodized Alumina Surfaces, D. Ganguly, C. D.L. Johnson, D. A. Borca-Tasciuc, R. J. Gilbert

Chemical and Biochemical Engineering Faculty Research & Creative Works

The Astrocytes are one of the most important and abundant resident glial cells of the central nervous system (CNS). They play a critical role in the foreign body response, by participating in the formation of the glial scar sunouncling implants. As part of the effort to minimize the foreign body response, biomaterials strategies einployiug engineered surfaces topographies are being explored. In this context, we have investigated the response of astrocytes to surface topography of alumiua, a material used in CNS applications. Specifically, astrocytes were seeded oil alumina surfaces with nanopores 20 nm and 100 nm in diameter, respectively. Pore-free alumina …

Effects Of Strontium Substitution On Bioactivity Of Hydroxyapatite, Chokchai Yatongchai, Lana M. Placek, Mark R. Towler, Anthony W. Wren

Chemical and Biochemical Engineering Faculty Research & Creative Works

Effect of strontium (Sr) substitution on bioactivity of hydroxyapatite (HA) was investigated. The substitution of Sr²⁺ for Ca²⁺ in the HA lattice increases biodegradability of Sr-substituted HA (Sr-HA) and accelerates the formation of apatite crystals on the Sr-HA surface. Moreover, the dissolution products from HA and Sr-HA samples are not cyto-toxic.