Engineering Commons^™

Enhanced Oil Recovery By Hydrophilic Silica Nanofluid: Experimental Evaluation Of The Impact Of Parameters And Mechanisms On Recovery Potential, Tariq A. Chandio, Muhammad A. Manan, Khalil R. Memon, Ghulam Abbas, Ghazanfer R. Abbasi

Research outputs 2014 to 2021

Nanofluids as an EOR technique are reported to enhance oil recoveries. Among all the nanomaterial silica with promising lab results, economic and environmental acceptability are an ideal material for future applications. Despite the potential to enhance recoveries, understanding the two-fold impact of parameters such as concentration, salinity, stability, injection rate, and irreproducibility of results has arisen ambiguities that have delayed field applications. This integrated study is conducted to ascertain two-fold impacts of concentration and salinity on recovery and stability and evaluates corresponding changes in the recovery mechanism with variance in the parameters. Initially, silica nanofluids’ recovery potential was evaluated by …

Physical Vapor-Deposited Silver (Ag)-Based Metal-Dielectric Nanocomposites For Thin-Film And Coating Applications, Mohammad Nur-E-Alam, Mohammad Kairul Basher, Mikhail Vasiliev, Narottam Das

Research outputs 2014 to 2021

Metallic thin-film materials and nanoparticles (mainly silver (Ag)-based) are recently being used in many nano-technological applications, including sensors, reflective heat-mirror coatings, and antibacterial coatings. The physical vapor deposition technique has attracted significant attention for Ag-based nanocomposites with tailoring of the structural and optical properties of metallic thin films, thus allowing for further improvements and application possibilities in various existing fields, namely electronics, catalysis, magnetics, and optics, alongside the environment and health and new emergent fields, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of silver (Ag)-based nanocomposite thin films prepared …

Shale Adhesion Force Measurements Via Atomic Force Microscopy, Nikolai Mitiurev, Michael Verrall, Svetlana Shilobreeva, Alireza Keshavarz, Stefan Iglauer

Research outputs 2014 to 2021

Wettability of sedimentary rock surface is an essential parameter that defines oil recovery and production rates of a reservoir. The discovery of wettability alteration in reservoirs, as well as complications that occur in analysis of heterogeneous sample, such as shale, for instance, have prompted scientists to look for the methods of wettability assessment at nanoscale. At the same time, bulk techniques, which are commonly applied, such as USBM (United States Bureau of Mines) or Amott tests, are not sensitive enough in cases with mixed wettability of rocks as they provide average wettability values of a core plug. Atomic Force Microscopy …

Assessing Solvent Viscosity Impact On The Physical Characteristics Of Polymeric Organogels, Cameron Hong

Honors Theses

Traditionally, studies of polymeric organogels focus on the impact of polymer factors (e.g., molecular weight and polymer concentration) on the gels’ mechanical and transport properties. Alternatively, this study seeks to assess the impact of altering solvent viscosity, while holding polymer factors constant. The gels in this study were composed of different viscosity mineral oils, styrene-ethylene-butylene-styrene (SEBS) triblock copolymer as a gelator, and oleic acid (OA) as a model drug. Samples were formulated to have 6.5, 11.2, and 15.7 wt% SEBS copolymer for each mineral oil, varying in viscosity from ≈30 mPa*s to ≈500 mPa*s. Uniaxial mechanical testing was performed to …

Assessing The Impact Of Block-Selective Homopolymers On The Diffusion Of Payload Through Polymeric Organogels, Ian Coates

Honors Theses

Styrenic polymer gels have received recent attention for their application in transdermal patches due to their unique properties. Previous research in the pharmaceutical industry has identified that polymeric gels, specifically styrenic gels, have the potential to encompass multiple functions of the transdermal delivery patch including controlling mechanical and delivery properties. To tailor styrenic gels either the gel nanostructure or the drug complex can be controlled. Specifically, this thesis investigated the effect of gel nanostructure in an attempt to control the gel diffusivity and mechanical properties. To control gel nanostructure a phase selective styrene homopolymer was used at varying concentrations. It …

Determination Of Hydrogel Degradation By Passive Mechanical Testing, Avery Rosh-Gorsky

Honors Theses

This paper details a new technique to measure the mechanical properties of ETTMP PEGDA hydrogels using Hertz Contact Theory and simultaneously analyze both the model drug release and gel erosion in situ. This method involves curing a drug loaded hydrogel in a standard cuvette and placing a glass bead and phosphate buffer solution (PBS). Over time, the cross-linked network of the hydrogel breaks down, and, as a result, the ball sinks into the hydrogel. This method provides a macroscopic and inexpensive way to continuously and passively measure properties of the hydrogel as the hydrogel degrades. By plotting both the …

Cyclic Sequential Adsorption Desorption/Thermal-Catalytic Oxidation Of Volatile Organic Compounds: Material Development, Process Advancement/Improvement, And Numerical Modeling, Simulation And Optimization, Busuyi Ojo Adebayo

Doctoral Dissertations

"Volatile organic compounds (VOCs) are a group of useful organic chemicals but when emitted have contributed to air pollution. They affect human health, cause environmental degradation and contaminate our waters and soils, so they need to be controlled. When they exist in dilute concentrations, abatement becomes challenging, thus requiring advanced abatement methods, e.g., sequential adsorption desorption/thermal-catalytic oxidation process. The overall goal of this research was to abate dilute streams of VOCs via the process. The specific objectives were to 1) develop novel adsorbent/catalyst dual-function materials (DFMs) for the process, 2) improve the operability of a one-bed-one-column reactor configuration for the …

Relationships Among Mineralogy, Geochemistry, And Oil And Gas Production In The Tuscaloosa Marine Shale, Hayley Roxana Beitel

Masters Theses

"The Tuscaloosa Marine Shale (TMS) is an unconventional shale reservoir located in southeast Louisiana and southwest Mississippi. Limited mineralogical and geochemical data for the TMS have been published. The data that do exist indicate that the formation is heterogeneous. Consequently, previous investigators and oil and gas companies have not managed to effectively link mineralogical and chemical changes to oil and gas production in the TMS. These linkages are critical to establish for future exploration efforts. In this study, we attempt to establish these relationships by gathering all existing mineralogical and chemical data in the TMS, including newly acquired data from …

Analysis Of Refracturing Activities In The Major Shale Plays In The United States, Faisal Shammam

Masters Theses

"Refracturing of existing horizontal multistage wells has increased over the past decade in the oil industry. This work aims to investigate all the refracturing operations in the most active shale plays in the united states (Bakken, Niobrara, Marcellus, Permian, Eagle Ford, Barnett, and Haynesville) in terms of completion technique, candidate selection, treatment types, and refracturing production efficiency. To collect the data of the refractured wells, an advanced data analytics approach was applied to separate the refractured wells from 170,000 wells reported in FracFocus, a public chemical registry for hydraulic fracturing in the United States, and combine it with DrillingInfo database, …

Doping Graphene With Substitutional Mn, Pin-Cheng Lin, Renan Villarreal, Simona Achilli, Harsh Bana, Maya N. Nair, Antonio Tejeda, Ken Verguts, Stefan De Gendt, Manuel Auge, Hans Hofsäss, Steven De Feyter, Giovanni Di Santo, Luca Petaccia, Steven Brems, Guido Fratesi, Lino M. C. Pereira

Advanced Science Research Center

We report the incorporation of substitutional Mn atoms in high-quality, epitaxial graphene on Cu(111), using ultralow-energy ion implantation. We characterize in detail the atomic structure of substitutional Mn in a single carbon vacancy and quantify its concentration. In particular, we are able to determine the position of substitutional Mn atoms with respect to the Moiré superstructure (i.e., local graphene-Cu stacking symmetry) and to the carbon sublattice; in the out-of-plane direction, substitutional Mn atoms are found to be slightly displaced toward the Cu surface, that is, effectively underneath the graphene layer. Regarding electronic properties, we show that graphene doped with substitutional …

Application Of Fiber Optics Das On Completion Design Optimization, Aliou Sylla

Graduate Theses, Dissertations, and Problem Reports (ETD)

Interstage communication during well stimulation reducing the effectivity of the well completion is known to be a concern in the oil and gas industry. The leading cause of this is fracture communication due to the presence of natural fractures where the formation is being hydraulically fractured. In this study, a technique was developed to map natural fractures, on a larger scale, underground to be able to avoid the high fracture intensity zones when hydraulically fracturing. This study developed a technique to optimize well completion designs by introducing the ability of locating natural fractures zones in the formation (Marcellus Shale) which …

Analyzing And Measuring Petrophysical Properties Of Marcellus Shale, Yahia Mustafa Yassin Mustafa

Graduate Theses, Dissertations, and Problem Reports (ETD)

Unconventional oil and natural gas play a key role in our nation's future. The U.S. has vast reserves of such resources that are commercially viable as a result of advances in horizontal drilling and hydraulic fracturing technology. These technologies enable greater access to oil and natural gas in shale formations. Responsible development of America's shale gas resources offers important economic, energy security, and environmental benefits. Hydraulic fracturing and horizontal drilling apply the latest technologies and make it commercially viable to recover shale gas and oil.

In order to estimate the original gas-in-place, predict the production rates, and optimize the hydraulic …

Dry Reforming Of Methane Using Microwave Irradiated Metal Oxide/Coal Char Catalysts, Anthony Carter

Graduate Theses, Dissertations, and Problem Reports (ETD)

This research focuses on the synthesis of both shaped and amorphous powder materials, the combination of these materials with dried Powder River Basin (PRB) coal char, and their reactionary properties with methane and carbon dioxide gasses with conventional and microwave (MW) heating. The first goal of this project was to synthesize shaped micro and nano sized particles with ideal dielectric properties for converting electromagnetic energy into heat and proven capabilities of activating methane. These particles were synthesized via solvothermal, hydrothermal, and co-preceptory treatments alone and onto the surface of dried PRB coal char. PRB is a sub-bituminous, low-ranking coal (LRC) …

Quantifying The Impact Of Load-Following On Gas-Fired Power Plants, Yifan Wang

Graduate Theses, Dissertations, and Problem Reports (ETD)

Due to rapid penetration of renewables into the grid, natural gas combined cycle (NGCC) power plants are being forced to cycle their loads more frequently and rapidly than for which they were designed. However, the impact of load-following operation on plant efficiency and equipment health are currently poorly understood. The objective of this work is to quantify the impact of load-following on the gas-fired plants by developing high-fidelity multi-scale dynamic models. There are four main tasks in this project. First, dynamic model of an NGCC power plant has been developed. The main components of the NGCC plants are the gas …

Advanced Raman Spectroscopy Detection Of Oxidative Damage In Nucleic Acid Bases: Probing Chemical Changes And Intermolecular Interactions In Guanosine At Ultralow Concentration, Francesca Ripanti, Claudia Fasolato, Flavia Mazzarda, Simonetta Palleschi, Marina Ceccarini, Chunchun Li, Margherita Bignami, Enrico Bodo, Steven E.J. Bell, Filomena Mazzei, Paolo Postorino

Bioelectrics Publications

DNA/RNA synthesis precursors are especially vulnerable to damage induced by reactive oxygen species occurring following oxidative stress. Guanosine triphosphates are the prevalent oxidized nucleotides, which can be misincorporated during replication, leading to mutations and cell death. Here, we present a novel method based on micro-Raman spectroscopy, combined with ab initio calculations, for the identification, detection, and quantification of oxidized nucleotides at low concentration. We also show that the Raman signature in the terahertz spectral range (<100 >cm(-1)) contains information on the intermolecular assembly of guanine in tetrads, which allows us to further boost the oxidative damage detection limit. Eventually, we …

Establishing Independent Tunability Of The Mechanical And Transport Properties Of Polymer Gels, Lucas Rankin

Master’s Theses

Polymer gels can be used in the fabrication of materials for filtering liquid and gaseous media, solid-state electrolytes, and transdermal medical patches. This diverse range of applications primarily relies on the transport and mechanical properties of polymer gels. Both sets of properties have shown excellent tunability, but typically in a coupled fashion. Establishing the independent tunability of the transport and mechanical properties of polymer gels (using simple, cost-effective methods) is paramount if polymer gels are to be used to their full potential. Specifically, block copolymer gels self-assemble into organized nanoscale networks within the gel solvent, which allows for facile control …

The Characterization Of Purified Citrate-Coated Cerium Oxide Nanoparticles Prepared Via Hydrothermal Synthesis, Matthew L. Hancock, Robert A. Yokel, Matthew J. Beck, Julie L. Calahan, Travis W. Jarrells, Eric J. Munson, George A. Olaniyan, Eric A. Grulke

Chemical and Materials Engineering Faculty Publications

Hypothesis

Cerium oxide nanoparticles were synthesized using a hydrothermal approach with citric acid as a stabilizing agent. Citric acid adsorption onto the nanoceria particle surface can cease particle formation and create a stable dispersion for an extended shelf life. The product was dialyzed immediately following the synthesis to remove unreacted cerium that could contribute to biological effects. Nanoparticle characterization results are expected to help identify the surface citrate bonding structure.

Experiments

Many characterization techniques were utilized to determine size, morphology, surface properties, and citrate complexation on the nanoceria particle surface. These included transmission electron microscopy, electron energy loss spectroscopy, dynamic …

Enhancing Emulsion Liquid Membrane System (Elm) Stability And Performance For The Extraction Of Phenol From Wastewater Using Various Nanoparticles, Faris H. Al-Ani, Qusay F. Alsalhy, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

Emulation liquid membrane (ELM) technology has recently garnered attention as an efficient alternative for separating pollutants, but it faces the problem of instability during the application, as well as emulsion breaking. With this in mind MgO, Al₂O₃, and three magnetic Fe₂O₃ nanoparticles (of different sizes) were utilized to fabricate a new Pickering ELM system (PELM). The extraction efficiency of phenol from aqueous solution by PELM was studied with different NPs types and with different phenol concentrations (1,000; 500; 100; and 50 ppm). It was found that the type of NPs and concentration of …

Cold Plasma Enhanced Active Sites On Supported Nip Nanoparticles For The Oxygen Evolution Reaction, Michael Ricci

Williams Honors College, Honors Research Projects

Identifying materials to efficiently facilitate the oxygen evolution reaction (OER) is key to advancing water electrolysis, an essential technology in the pathway towards a sustainable energy future. Here, we explore cold-plasma treatment as a facile method to enhance the activity of NiP nanoparticles supported on activated carbon. NiP nanoparticles were synthesized on an activated carbon support using a solid-state method and were then treated with argon, oxygen, and hydrogen plasmas for extended times. In all cases, plasma treatment reduced the number of active sites on the support. OER activity was evaluated by testing the materials in alkaline conditions. The activities …

Testing The Effectiveness Of Various Fabrics For Use In Protective Face Coverings, Isaac Daley

Williams Honors College, Honors Research Projects

Facemask requirements have been heavily implemented as a result of the COVID-19 pandemic. The purpose of this study was to test various fabrics that could be used in face coverings and determine which materials are best for reducing virus transmission rates. Of the seven fabrics tested, five were conventional home-use fabrics and the other two were surfaces modified with hydrophobic organosilanes. Wettability and droplet adherence tests were performed on each material. The materials that performed the best were decyltrichlorosilane (DTS) modified cotton, perfluorotrichlorosilane (FTS) modified cotton, and polyester. Contact angles for water droplets on these fabrics were 106°, 93°, and …

Development Of Phagotrophic Algae-Based Process For Conversion Of Waste Organics To Algae Lipids As Potential Feedstock For Biofuel, Hannah Nelson

Williams Honors College, Honors Research Projects

Interest in sustainable feedstock for biofuel has encouraged research on the production of phagotrophic algae from bacteria using a two-staged continuous-flow system. Bacteria cultures were fed the content of a waste stream from The J.M. Smuckers Company containing high concentrations of sugar. In the design, the bacteria effluent overflowed into the algae tank which was kept at a set volume. Several methods were developed to assist in maintaining the system at steady state and minimize the impact from contaminants. A rigorous cleaning protocol was implemented for both tanks, effectively eliminating protozoa from the bacteria system. The protozoa were decreased in …

Evaluating The Thermoresponsive Properties Of Hydroxypropyl Cellulose Solutions For Smart Window Applications, Adam Reed

Williams Honors College, Honors Research Projects

With HVAC and building energy usage expected to increase, there is a strong need for autonomous thermal management solutions. In particular, there has been a growing interest in thermoresponsive (TR) smart windows that are activated by ambient temperature changes. Most TR smart windows contain a liquid solution between two panes. The goal of this research project was to develop a self-supporting smart window by forming a gel that maintained its TR properties. A gel is less prone to spilling in the case of window breakage. It was also desired to tune the phase transition to occur at environmentally relevant conditions …

Wetting Transition On 3d-Printed Featured Surface, Hannah Pineault

Williams Honors College, Honors Research Projects

The primary objective of this research project was to gain a better understanding of surface characteristics to produce a long-lasting superhydrophobic or superhydrophilic surface. In other words, when will a droplet of water remain on top of a featured surface and when does the transition occur to water filling the grooves of the surface? This research focused on how to best fabricate porous structures that would stay completely dry at all times by preventing the liquid from penetrating. In particular, we followed the behaviors of water droplets placed on top of 3-D printed featured surfaces with various geometries and surface …

Comparison Of The Effects Of Hofmeister Ions On Transition Temperature Of Two Thermoresponsive Polymers, Ashley Knight

Williams Honors College, Honors Research Projects

It has been hypothesized that poly(vinylmethylether) (PVME) could be used to replace poly(N-isopropylacrylamide) (pNIPAAM) in various thermoresponsive applications based on literature searches and previous lab experiments. PVME is cheaper and easier to process, and would make pNIPAAM applications more cost effective. In order to verify this, experimental data was gathered on the effects of four anions from the Hofmeister series (SO₄₂-, Cl-, I-, and SCN-) on the lower critical solution temperature (LCST) of pNIPAAM and compared to previous data collected on PVME. Commercial pNIPAAM from Sigma Aldrich and Polysciences were used. The reported LCST range for pNIPAAM is …

Investigation Of Surface Charge Using Faraday Bucket Measurements: Analysis On Electrospun Polyvinylidene Fluoride Fiber Mats, Ryan Kantenwein

Williams Honors College, Honors Research Projects

Piezoelectric polymer materials such as polyvinylidene fluoride exhibit beneficial properties for use in personal protective equipment (PPE) against viral contaminants and other foreign microparticles. The electrospinning process of this material allows for surface charge to develop over a controlled surface area. Kynar 761 at 10 wt% demonstrates increased surface charge after withstanding a flow of aerated NaCl particles from a TSI 8130 instrument. Utilizing voltage measurements from a Faraday bucket, 18 wt% Kynar 761 and MG-15 exhibit surface charge when undergoing an electrospinning process; however, Kynar MG-15 displays lower charge values than that of Kynar 761. Several critical factors such …

Simulation Of Water Loading In Filter Medium, Anthony Mole

Williams Honors College, Honors Research Projects

This research will model fluid flow through a filter plugged with water droplets using FlexPDE software. After simulations are run at various initial conditions, curves will be developed to correlate the permeability of the filter to variables like water droplet distribution and size.

Relating Modified Ergun's Equation To Hindered Settling Correlations, Ryan Zahniser

Williams Honors College, Honors Research Projects

Correlations were developed between the Modified Ergun’s and Hindered settling correlations under the condition of dense packing of particles in the bed. As the porosity of the slurry increases, so does the interference between particles in the solution which mimics the behavior of a packed or densely concentrated fluidized bed. The similarity between the two sets of conditions was modeled using mathematical equations to calculate settling velocities and pressure drops by means of the Hindered Settling correlations and Modified Ergun’s equation at porosities ranging from 0.4242 to 0.89. The results showed that a porosity of 0.52 and 0.009 ft particle …

The Effects And Motion Of An Air-Filled Cylinder Being Submerged In Water In The Axial Direction, Ethan Davis

Williams Honors College, Honors Research Projects

Submarines operate on the basis of a difference in relative densities between of vessel and the surrounding fluid. This principle is based on the force balance that exists between the total buoyancy force and the force due to gravity. Previous work focuses on the neutral buoyancy depths and velocities of object that once submerged, their buoyancy force is a constant along with the force due to gravity. This work aims to better understand how the compression of air at various depths below the surface of the water contribute to the neutral buoyancy depth, velocity of the object as it rises, …

Increasing The Corrosion Protection Of Aisi 1008 Carbon Steel By Surface Treatment With Unmodified And Benzotriazole Modified Sol-Gel Films, Shane Thomas Kelliher

Williams Honors College, Honors Research Projects

The corrosion performance of sol-gel coated AISI 1008 carbon steel was investigated in 3.5 wt% NaCl solutions of pH 7, 9, and 12 using electrochemical measurements. A corrosion inhibitor, benzotriazole (BTA) was added to the sol-gel mixture and tested as a second, modified sol-gel coating. Sol-gel films adhered evenly to metal samples and were characterized by FTIR spectroscopy. Electrochemical Impedance Spectroscopy (EIS) showed an increase in polarization resistance from blank to sol-gel coated samples (600-18,800,000 ohms). Cyclic polarization (CPP) curves showed positive hysteresis loops for blank and unmodified sol-gel coated samples which increased at high pH following the backward potential …

Quantifying Mafenide Release From 3d Printed Phenylalanine-Coumarin Copolyester Scaffolds, Jacob Seeh

Williams Honors College, Honors Research Projects

This project addressed burn wound healing through controlled release of the antibacterial drug mafenide encapsulated by a copolyster into 3D printed scaffolds. Scaffolds were printed at 25^oC and 0.77-1 bar in a cross-hatch pattern with uniform thickness, distance between parallel layers, and diameter then photo-crosslinked. The number of scaffolds available for testing was limited by the amount of polymer that could be synthesized. A high-performance liquid chromatography method was developed specifically for this experiment and used to determine daily release of mafenide from the scaffold into a 2-mL phosphate buffer solution. During the first 24 hours a large …