Engineering Commons^™

Evaluation Of The Mechanical Properties Of Pla Material Used For 3d Printing Solar E-Hub Component, Md Helal Uddin, Mohammad Nur-E-Alam, Abreeza Manap, Boon Kar Yap, Md Rokonuzzaman

Research outputs 2022 to 2026

The advent of additive manufacturing (AM) technologies revolutionized design and production processes across various industries. In renewable energy, AM enabled new possibilities for optimizing solar e-hub (solar energy harvesting module) configurations, enhancing efficiency and performance. This study examined critical considerations such as material selection, durability, and cost-effectiveness in solar hub development. This fast-prototyping technique was controlled by computer-aided design (CAD) software like CREO Parametric 7.0 and Creality Slicer 4.8. Experimental results indicated that PLA (Polylactic acid) materials exhibited superior strength, with an impact energy of 4.8 Joules. The deformation study revealed that the maximum load of 22 MPa aligned with …

Electrified Membrane For Water Treatment And Resource Recovery: Advancing Multiscale Strategies In Gas-Involving Reactions, Jianan Gao

Dissertations

Multifunctional, modular, and scalable water treatment technologies that operate without chemical additives are crucial for addressing global water pollution challenges. While traditional membrane-based separation processes are crucial for ensuring clean water supplies, they primarily focus on pollutant removal rather than on the upcycling of pollutants into valuable resources. Electrified membrane filtration presents a robust alternative, utilizing minimal or no chemical additives and harnessing electrical power to directly reduce contaminants or produce reactive oxidants or reductants on-site.

This dissertation is dedicated to the development of innovative electrochemically reactive membranes designed to address three major challenges: (1) the engineering of electrocatalysts with …

Microwave Catalysis-Enabled Membrane Processes For Microbial Inactivation, Fangzhou Liu

Dissertations

The COVID-19 pandemic has highlighted the urgent need for advanced technologies to combat virus transmission. Traditional membrane filtration technologies primarily serve as physical barriers, capturing pollutants but failing to inactivate microbial agents such as bacteria and viruses. These membranes typically target larger particles but are ineffective against sub-micrometer viral particles. Thus, there's a critical demand for membrane filtration processes that combine robust filtration with antifouling and reaction -enabled functions for efficient pathogen disinfection. This research explores a novel microwave-assisted membrane filtration process incorporating catalytic reactions to enhance microbial disinfection and prevent membrane fouling, offering a groundbreaking solution to global challenges …

Collision Dynamics Of Compound Droplets In Microchannels: A Combined Numerical And Data-Driven Study, S M Abdullah Al Mamun

Dissertations

Understanding and predicting the hydrodynamic interactions of micron-scale droplets is crucial in a wide range of industrial and real-life applications, including microfluidics, pharmaceutics, drug delivery, food science, and enhanced oil recovery. These multi-phase and multi-scale phenomena are further complicated by the presence of core droplets of an immiscible fluid within shell droplets, known as compound droplets. The collisions and interactions of droplets in emulsions are influenced by various physical and geometric parameters, leading to distinct rheological and dynamic responses. This research employs numerical methods for a systematic parametric study of both simple and compound droplet pair collisions under confined shear …

Mathematical Modelling Of The Solar Drying Of Apricot, Sarvar Rejabov, Botir Shukurillayevich Usmonov, Asqar Artikov, Komil Usmanov

Chemical Technology, Control and Management

Agricultural products provide significant growth in export earnings for many countries and provide food globally. Fruits and vegetables are perishable foods due to their high moisture content. Therefore, most agricultural products require post-harvest processing such as drying to extend the shelf life of fruits and vegetables and maintain nutrient quality. Solar drying is widely used for this purpose. Ambient temperature, humidity and solar radiation affect the drying time and quality of agricultural products, especially apricots, in solar dryers. The experiments were carried out in the same place (Tashkent, Uzbekistan) and in the same time interval. When the mass of apricots …

Experimental Study Of The Ultrasonic Extraction Process Of Plant Raw Materials, Azamat Bakir Ogli Usenov, Doston Ishmuxammat Ogli Samandarov, Qobil Akmal Ogli Mukhiddinov, Jasur Esirgapovich Safarov Dcs

Chemical Technology, Control and Management

In-depth scientific research is being conducted around the world aimed at developing the scientific and methodological foundations of energy-saving extractors, processing medicinal plants, increasing the efficiency of modern technologies, processes and equipment for obtaining high-quality pharmaceutical raw materials rich in biologically active substances. Energy-saving extractors, developed in conjunction with the extraction process of medicinal plants, are introduced into the industry using scientifically proven technology. At the global level, special attention is paid to the creation of intelligent designs of innovative extraction plants that operate using ultrasonic waves, allowing the extraction of medicinal components of plants.

Clustering Algorithm Based On Similarity Of Objects, Akhram Khasanovich Nishanov, Alisher Tulkunovich Tursunov, Fayzullo Farhod O'G'Li Ollamberganov

Chemical Technology, Control and Management

The article discusses the problem of drug clustering. Initially, k classes are randomly formed and the resulting training sample is preprocessed, then the similarity between objects of each class is assessed based on the proximity function and the criterion for assessing the contribution of objects to the formation of their own class. It is usually expressed as a percentage and represents the degree of mutual similarity of objects of each class. In the next steps of the algorithm, first one object is taken from the first class and by adding it to all k classes, the contribution of this object …

Capacitive Sensors With Ultra-Small Capacitance For Smart Measurement And Control Systems, Rustam Baratov, Farrux Jabbor O'G'Li Ko'charov

Chemical Technology, Control and Management

This article discusses methods of low capacitance measurement of capacitive sensors. The results of the study of the amplitude-frequency (AF) and phase-frequency (PF) response of measurement circuits of capacitive sensors for low capacitances measurement, consisting of RC - differentiating elements are presented. The input and output parameters of the differentiating circuit and the complex transfer function are analyzed. The research results show that low capacitances measurement by measuring the rectangular pulses duration is the most effective measurement method.

Synthesis Of A Control System For A Non-Stationary Dynamic Plant Based On A Regulator-Predictor, Isamiddin Hakimovich Siddikov, Begovot Sheraliyevich Ibragimov

Chemical Technology, Control and Management

The paper considers the issues of synthesizing a predictor controller as part of a control system for a non-stationary dynamic plant with a predictive model. Technological processes in industry, in essence, have non-stationarity properties, the parameters of which can change during the execution of technological operations. To control such nonstationary dynamic control plants, controllers built on the basis of predictive models have found wide application. The article is devoted to the issue of studying automatic control systems of a non-stationary dynamic plant with a base regulator-predictor. To synthesize a regulator - predictor, it is proposed to use a predictive model …

Developing Decision-Making Models And Algorithms To Help Prevent Emergencies, Mizaakbar Xakkulmirzayevich Hudayberdiyev, Oybek Zokirovich Koraboshev

Chemical Technology, Control and Management

The article is devoted to the solution of the scientific issue of decision-making support for the prevention and elimination of the consequences of emergency situations. The relevance of this issue is related to the need to develop a theoretical basis for optimizing the risk of adverse effects on human health and the environment in connection with emergency situations, and a predictive model for the development of emergency situations and their prevention or elimination of their consequences. The optimization of the importance measure of signs for predicting the values of the factors of fire conditions has been carried out. In addition, …

Investigation Of The Parameters Of Semicylindrical Capacitive Sensor, Erkin Uljaev, Elyor Faxriddinovich Khudoyberdiev, Shohrukh Nurali O‘G‘Li Narzullayev

Chemical Technology, Control and Management

This study introduces a semicylindrical capacitive sensor, featuring an internal dielectric insulator, designed to measure moisture levels in bulk and other materials while in motion. The research employs numerical analysis to explore the sensor's capacitance variation and evaluate its performance. The change in capacitance of the semicylindrical capacitive sensor in the picofarad range is easily converted into a change in the frequency of the generator, which is implemented on an operational amplifier with feedback. The generator circuit is quite compact, and its output can be connected directly to the discrete input of a microcontroller without a matching element. Using the …

Review Of Fuzzy Models And Fuzzy Methods For Analysis Of Information In Conditions Of Emotional Decision Making, Latafat Gardashova, Royal Shirinov, Diana Boqdanova

Chemical Technology, Control and Management

In the modern world, decision-making often takes place in an environment of uncertainty and under the significant influence of emotional factors, which requires the use of special methods for analyzing information. This study is devoted to an overview of fuzzy models and methods that allow such factors to be taken into account when making decisions. In particular, the approaches based on fuzzy logic, fuzzy cognitive maps and fuzzy clustering methods that provide flexibility and adaptability in conditions of uncertainty are considered. The study analyzes examples of the application of these methods in various fields, including risk management, medical diagnostics and …

Optimization Of Bioethanol Production Using An Enzymatic Hydrolysis Process With Green Algae (Chaetomorpha) As The Raw Material, Teuku Maimun, Mirna Rahmah Lubis, Muhammad Aldi Zein, Wahed Febbry Andriansyah Ali

Makara Journal of Technology

Bioethanol is an alternative fuel derived from biological feedstock used to decrease the reliance on fossil fuels because of increasing energy consumption associated with population growth and increased use of oil fuels. Bioethanol production has been widely conducted using several types of algae, but the optimal conditions for the hydrolysis and fermentation processes are not explained in more detail. Therefore, this study focuses on determining the optimal conditions for hydrolysis and fermentation to maximize the bioethanol yield. This study uses optimization based on the hydrolysis time, temperature, and pH to increase the reducing sugar content using high-performance liquid chromatography in …

Addressing Strain And Porosity Changes Of Battery Electrodes Due To Reversible Expansion Through Dem Simulations, Hunter Teel, Taylor R. Garrick, Srikant Srinivasan, Fengkun Wang, Yangbing Zeng, Sirivatch Shimpalee

Faculty Publications

In this work, discrete element method (DEM) simulations were used to probe changes in electrode porosity, electrode strain, and the resultant pressure changes for composite electrodes comprised of active material and binder particles. Through the results acquired by these simulations, three cases that are representative of two limiting cases for electrode operation, and one case for realistic electrode face pressure during operation were captured and the implications on design and performance are discussed. Predicting changes in the porosity is a unique insight that is difficult if not impossible to capture experimentally but is important for predicting changes in electrochemical performance …

Winning Results Of The 2Nd Xiamen University Short Video Abstract Contest For Science And Technology Papers, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Winning Works From Journal Of Electrochemistry: The 2Nd Xiamen University Short Video Abstract Contest For Science And Technology Journal Papers, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

2024 "Electrochemical Research Paradigms" Summer School Successfully Held, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Upcoming Meeting-The 1St Young Investigator Symposium On Electrosynthesis, Chinese Chemical Society, Chinese Society Of Electrochemistry (Cse)

Journal of Electrochemistry

No abstract provided.

Recent Advances On Ruthenium-Based Electrocatalysts For Lithium-Oxygen Batteries, Yu-Zhe Wang, Zhuo-Liang Jiang, Bo Wen, Yao-Hui Huang, Fu-Jun Li

Journal of Electrochemistry

Rechargeable lithium-oxygen (Li-O₂) batteries have attracted wide attention due to their high energy density. However, the sluggish cathode kinetics results in high overvoltage and poor cycling performance. Ruthenium (Ru)-based electrocatalysts have been demonstrated to be promising cathode catalysts to promote oxygen evolution reaction (OER). It facilitates decomposition of lithium peroxide (Li₂O₂) by adjusting Li₂O₂ morphologies, which is due to the strong interaction between Ru-based catalyst and superoxide anion (O₂^–) intermediate. In this review, the design strategies of Ru-based electrocatalysts are introduced to enhance their OER catalytic kinetics in …

Rate Law For Photoelectrochemical Water Splitting Over Cuo, Bo-Yuan Gao, Wen-Hua Leng

Journal of Electrochemistry

Photocatalytic splitting of water over p-type semiconductors is a promising strategy for production of hydrogen. However, the determination of rate law is rarely reported. To this purpose, copper oxide (CuO) is selected as a model photocathode in this study, and the photogenerated surface charge density, interfacial charge transfer rate constant and their relation to the water reduction rate (in terms of photocurrent) were investigated by a combination of (photo)electrochemical techniques. The results showed that the charge transfer rate constant is exponential-dependent on the surface charge density, and that the photocurrent equals to the product of the charge transfer rate constant …

Numerical Analysis Of Explosion Characteristics Of Vent Gas From 18650 Lifepo4 Batteries With Different States Of Charge, Shi-Lin Wang, Xu Gong, Li-Na Liu, Yi-Tong Li, Chen-Yu Zhang, Le-Jun Xu, Xu-Ning Feng, Huai-Bin Wang

Journal of Electrochemistry

The combustion and explosion characteristics of lithium-ion battery vent gas is a key factor in determining the fire hazard of lithium-ion batteries. Investigating the combustion and explosion hazards of lithium-ion batteries vent gas can provide guidance for rescue and protection in explosion accidents in energy storage stations and new energy vehicles, thereby promoting the application and development of lithium-ion batteries. Based on this understanding and combined with previous research on gas production from lithium-ion batteries, this article conducted a study on the combustion and explosion risks of vent gas from thermal runaway of 18650 LFP batteries with different states of …

2024 World Fuel Cell Conference Held In Ningbo, Zhejiang, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Unveiling The Indoor Performance Of Perovskite/Silicon Tan‑Dem Solar Cells: A Comprehensive Exploration Through Numerically Modelled Energy Band Diagrams, Ziad Khalifa, Sameh O. Abdellatif, Alexander De-Bernardinis, Muath Alkadi, Mostafa Ganoud, Saif Qaid

Chemical Engineering

This paper delves into the indoor performance analysis of Perovskite/Silicon Tandem Solar Cells (PSSTC) through a detailed exploration utilizing numerically modeled energy band diagrams. The primary objective is to uncover the potential of PSSTC for solar energy conversion in indoor settings. Various tandem cell configurations are scrutinized under diverse artificial lighting spectra, with an innovative Li4Ti5O12/ CsPbCl3/MAPbBr3/CH3NH3PbI3/ Si architecture achieving an exceptional maximum power conversion efficiency of 25.25%. This represents a substantial efficiency enhancement of nearly 7% compared to standalone Silicon cells. The study underscores the significance of design optimization in maximizing performance. The energy band diagram analysis reveals a …

Voltammetric Determination Of Hydrogen Peroxide At Decorated Palladium Nanoparticles/Poly 1,5- Diaminonaphthalene Modified Carbon-Paste Electrode, Ziad Khalifa, Mohamed Fathi Abo Oura, Magdi Abdelazzem, Ablah Hathoot

Chemical Engineering

In this work, palladium nanoparticles (PdNPs)/p1,5-DAN/ carbon paste electrode (CPE) and p1,5-DAN/CPE sensors have been developed for determination of hydrogen peroxide. Both sensors showed a highly sensitive and selective electrochemical behaviour, which were derived from a large specific area of poly 1,5 DAN and super excellent electroconductibility of PdNPs. PdNPs/p1,5-DAN/CPE exhibited excellent performance over p1,5-DAN/CPE. Thus, it was used for detecting hydrogen peroxide (H2O2) with linear ranges of 0.1 to 250 μM and 0.2 to 300 μM as well as detection limits (S/N= 3) of 1.0 and 5.0 nM for square wave voltammetry (SWV) and cyclic voltammetry (C.V) techniques, respectively. …

Optogenetic Control Of Bacterial Dormancy, Yousr Dhaouadi Khattab

Dissertations - ALL

The presence of persister cells makes it difficult to eradicate chronic bacterial infections as these dormant subpopulations arise with exposure to stressors and are capable of surviving antimicrobials that target active cells. Persisters can also revert back to normal growing cells when stressors are removed thus reestablishing the infection. It is therefore important to understand the underlying mechanisms of persister formation, as well as wake-up, and target these systems in order to treat chronic bacterial infections. The formation of persisters, however, remains elusive as there is not yet a clear relationship between the various stages of dormancy. Persister cells can …

Chemistry And Processing Of Carbon/Carbon Composites From Furan-Based Polybenzoxazine Resins, Michael Chauby

Theses and Dissertations

Carbon/carbon (C/C) composites are valuable for applications requiring structural integrity at high temperatures. However, their widespread use is limited by high manufacturing costs. Monofunctional furan-based benzoxazine resins were identified as promising candidates for enhancing fabrication efficiency due to their low viscosity, high char yield, and high carbon density. A benzoxazine monomer synthesized from furfurylamine, formaldehyde, and benzyl alcohol (Bz-FA-H) exhibits a crosslinking reaction between the furan group and the hydroxymethyl para substituent on the phenol, not found with other monomers. An investigation using blends of monomers containing Bz-FA-H at various concentrations showed that increasing crosslink density resulted in increased bulk …

Quantifying The Impact Of Microstructure Variation On Charging Capability In Lithium-Ion Batteries, Hunter Teel, Taylor R. Garrick, Mitchell A. Sepe, Joseph S. Lopata, Srikant Srinivasan, Fengkun Wang, Yangbing Zeng, Sirivatch Shimpalee

Faculty Publications

Through the use of electrochemical simulations, variation in the local onset of lithium plating can be predicted and used to set charging guidelines to reduce the risk of lithium plating. The pseudo-two-dimensional (P2D) model is typically used for capturing this behavior; however, it only provides a global lithium plating onset estimate and does not consider the local variation. With material properties translated to an average continuum value, the P2D model can simulate rapid charge and capture global onset of lithium plating. However, this model lacks the ability to resolve localized behaviors across individual components due to local non-uniformities. Our three-dimensional …

Consistent Intraocular Pressure Reduction By Solid Drug Nanoparticles In Fixed Combinations For Glaucoma Therapy, Da Huang, Pedro Norat, Lin Qi, Anna Chernatynskaya, James D. Cole, Vimalin Jeyalatha Mani, Lei Xu, Xiaorong Liu, Hu Yang

Chemical and Biochemical Engineering Faculty Research & Creative Works

Efficient topical drug delivery remains a significant challenge in glaucoma management. Although nanoparticle formulations offer considerable promise, their complex preparation processes, co-delivery issues, and batch consistency have hindered their potential. A scalable fabrication strategy is developed here for preparing solid drug nanoparticles (SDNs) with enhanced drug delivery efficiency. Utilizing hydrophobic antiglaucoma drugs brimonidine (BM) and betaxolol (BX), uniform fixed combination BM/BX SDNs are fabricated through a continuous process, improving batch-to-batch consistency for combined glaucoma treatment. With trehalose being used as a lyoprotectant, BM/BX SDNs can be stored as dry powder and easily reconstituted in phosphate buffered saline. Importantly, reconstituted BM/BX …

A Coarse-Grained Molecular Dynamics Study Of Gas Hydrate Formation And Dissociation, Meisam Adibifard

LSU Doctoral Dissertations

The study of gas hydrates has increased significantly over the last two decades because of their potential application in energy storage, production and transportation, water desalination, refrigeration, gas separation, etc. There is a significant interest in commercially developing natural gas hydrates because the energy content of methane hydrate reservoirs (MHRs) is at least twice that of all conventional fossil fuels combined. Additionally, due to the higher storage capacity of hydrates, it is proposed to sequester CO₂ in the form of CO₂ hydrate, thereby reducing the amount of greenhouse gases. Hence, hydrates offer a dual solution to two of …

Investigation Of Heavy Metal Composition And Associated Health Risks From Selected Groundwater Wells In Temeke, Dar-Es-Salaam, Justin M. Jeremiah

Tanzania Journal of Engineering and Technology (TJET)

Water quality continues to be the challenge to residents in Dar es Salaam due to various anthropogenic activities in the city. This study was conducted to assess groundwater quality by determining concentrations of heavy metals. Both probability and Nonprobability sampling techniques were used to collect samples from 40 groundwater wells in 24 wards of Temeke municipal and analysed using Microwave Plasma Atomic Emission Spectrometer (Agilent 4210 MP-AES) at the Geochemistry Laboratory of the University of Dar es Salaam. Results indicated varying heavy metal concentrations ranging from 0.71 ± 0.08 to 6.64 ± 0.21 mg/l for As, 0.02 ± 0.01 to …