Engineering Commons^™

Nitrogen Transformations During Secondary Coal Pyrolysis, Haifeng Zhang, Thomas H. Fletcher

Faculty Publications

A CO/H₂/O₂/N₂ flame was operated under fuel-rich conditions in a flat flame reactor to provide a high-temperature, oxygen-free environment to study secondary reactions of coal volatiles. The distributions of fuel nitrogen in the devolatilization products of four coals, ranging from high volatile bituminous to lignite, were obtained at gas temperatures ranging from 1159 to 1858 K. It was found that the initial nitrogen released was contained almost exclusively in the tar for all coals. Release of nitrogen from the char as light gases started at a later stage than tar nitrogen release. During secondary reactions, …

Simulation Of Coal Pyrolysis In Plasma Jet By Cpd Model, Yajun Tian, Kechang Xie, Suyu Zhu, Thomas H. Fletcher

Faculty Publications

Reaction of coal in a plasma jet is complex and extremely rapid, and acetylene and carbon monoxide are the main products in the pyrolysis gas. Coal pyrolysis is assumed as the first step reaction when coal is injected into hot plasma jet with initial average temperature of 3700 K. Chemical percolation devolatilization (CPD) is employed first to simulate this procedure in mechanism. The calculation results indicate coal pyrolysis rate in plasma jet is very fast and the retention time of coal staying in reactor is only several milliseconds. Comparing the calculation with experiment result, it was concluded that the CPD …

Transformations Of Coal-Derived Soot At Elevated Temperature, Thomas H. Fletcher, Jim Rigby, Jinliang Ma, Brent W. Webb

Faculty Publications

Coal pyrolysis experiments were performed in the post-flame region of a CH₄/H₂/air flat-flame burner operating under fuel-rich conditions, where the temperature and gas compositions were similar to those found in the near-burner region of an industrial pulverized coal-fired furnace. Volatiles released from the coal particles formed a cloud of soot particles surrounding a centrally fed coal/char particle stream. Soot samples were collected from the cloud at different residence times using a water-cooled, nitrogen-quenched probe. The soot samples were then analyzed for their elemental compositions of carbon, hydrogen, nitrogen, sulfur, and (by difference) oxygen plus inorganic matter. …

Linear-Nonequilibrium Thermodynamics Theory For Coupled Heat And Mass Transport, Yaşar Demirel, Stanley I. Sandler

Yaşar Demirel Publications

Linear-nonequilibrium thermodynamics (LNET) has been used to express the entropy generation and dissipation functions representing the true forces and flows for heat and mass transport in a multicomponent fluid. These forces and flows are introduced into the phenomenological equations to formulate the coupling phenomenon between heat and mass flows. The degree of the coupling is also discussed. In the literature such coupling has been formulated incompletely and sometimes in a confusing manner. The reason for this is the lack of a proper combination of LNET theory with the phenomenological theory. The LNET theory involves identifying the conjugated flows and forces …

Hysteresis During Cycling Of Nickel Hydroxide Active Material, Venkat Srinivasan, John W. Weidner, John Newman

Faculty Publications

The nickel hydroxide electrode is known to exhibit a stable hysteresis loop, with the potential on charge being higher than that on discharge at every state-of-charge (SOC). What we show here is that this loop created during a complete charge and discharge (i.e., boundary curves) is not sufficient to define the state of the system. Rather, internal paths within the boundary curves (i.e., scanning curves) can be generated that access potentials between the boundary curves. The potential obtained at any SOC, as well as how the material charges and discharges from that point, depends on the …

Multimode Quantitative Scanning Microwave Microscopy Of In Situ Grown Epitaxial Ba1-XSrXTio3 Composition Spreads, K. S. Chang, M. Aronova, O. Famodu, I. Takeuchi, S. E. Lofland, Jason R. Hattrick-Simpers, H. Chang

Faculty Publications

We have performed variable-temperature multimode quantitative microwavemicroscopy of in situepitaxial Ba_1−xSr_xTiO₃ thin-film composition spreads fabricated on (100) LaA₁O₃ substrates. Dielectric properties were mapped as a function of continuously varying composition from BaTiO₃ to SrTiO₃. We have demonstrated nondestructive temperature-dependent dielectric characterization of local thin-film regions. Measurements are simultaneously taken at multiple resonant frequencies of the microscope cavity. The multimode measurements allow frequency dispersion studies. We observe strong composition-dependent dielectric relaxation in Ba_1−xSr_xTiO₃ at microwave frequencies.

Approximate Solutions For Galvanostatic Discharge Of Spherical Particles I. Constant Diffusion Coefficient, Venkat R. Subramanian, James A. Ritter, Ralph E. White

Faculty Publications

Approximate models are developed, based on second, fourth, and sixth order polynomials, that describe the concentration profile of an electrochemically active species in a spherical electrode particle. Analytical expressions are obtained that describe the way the concentration profiles, surface concentrations, and electrode utilization change during the galvanostatic discharge of an electrode particle. Based on a comparison with an exact analytical model over a wide range of dimensionless current densities, all three approximate models performed extremely well in predicting these quantities. Quantitative criterion for the validity of these models is also developed and shows that the sixth order, four parameter approximate …

Modeling Of A Nickel-Hydrogen Cell: Phase Reactions In The Nickel Active Material, B. Wu, Ralph E. White

Faculty Publications

No abstract provided.

Modeling Lithium Intercalation In A Porous Carbon Electrode, Gerardine G. Botte, Ralph E. White

Faculty Publications

No abstract provided.

Synthesis And Characterization Of Hydrous Ruthenium Oxide-Carbon Supercapacitors, Manikandan Ramani, Bala S. Haran, Ralph E. White, Branko N. Popov

Faculty Publications

It is shown that composite Ru oxide-carbon based supercapacitors possess superior energy and power densities as compared to bare carbon. An electroless deposition process was used to synthesize the ruthenium oxide-carbon composites. Ru is dispersed on the carbon matrix as small particles. The effect of electrochemical oxidation and temperature treatment on the material performance has been studied extensively. Increasing the oxidation temperature reduces the proton transport rate and also increases the degree of crystallinity of the deposits. This adversely affects the performance of the composite. Loading a small amount of Ru oxide (9 wt %) on carbon increases the capacitance …

Effects Of Compression Processing Parameters And Antioxidants On Molecular Degradation Of Biodegradable Poly-L-Lactide (Plla), Thomas J. Hannan Jr.

Masters Theses

The purpose of this research was to find a combination of poly (L-lactic acid), also known as poly-L-lactide or (PLLA) and antioxidants that would, together, produce a product whose degradation rate would be advantageous for use in biodegradable medical implants. Intrinsic viscosity tests were conducted on compression molded samples of PLLA that were molded at various processing parameters in order to find optimal parameters. The optimal processing parameters were found to be time 10 minutes, temperature 220°C, and pressure 1000 psi.

The molecular weight of PLLA sample was taken while pressure, time, and temperature were varied. As pressure increased, no …

Diamondlike Carbon Thin Film Deposition Using A Rf Planar Coil Inductively Coupled Plasma System, Wai Soon Liew

Student Works (2000-2009)

A RF planar coil inductively coupled plasma system (ICPs) is setup for this project. The system is powered by a 13.56MHz, 550W, 500 RF generator. The RF power is transferred to the plasma via a planar induction coil. The impedance matching circuit consists of an air-core step-down transformer and a tunable vacuum capacitor. The typical E-H mode transition which is distinctive to the ICP has been observed in argon plasma, hydrogen plasma and hydrogen-methane admixture plasma. The studies carried out include the observation of intensity of light emission from the plasma, the power transferred at different pressures, the concentration of …

The Effects Of Incorporation Of Polyethylene Glycol On Properties Of Silica-Carbon Black-Filled Rubber Compound, Yoke Cheng Tang

Student Works (2000-2009)

The use of polyethylene glycol (PEG) to modify the surface of precipitated silica by means of physical adsorption was investigated. The effects of adding PEG on processing, cure and physical properties of a silica-carbon black-filled natural rubber truck tread compound were examined. For each series of investigation, two sets of experiments were conducted. Set I was to check the effects of both physical adsorption due to PEG and chemical modification due to a silane coupling agent, Si-69 on the surface of silica. Set 2 was to check the effects of physical adsorption due to PEG alone on the surface of …

Auditing And Biological Treatment Of Oleochemical Industry Waste, Fauziah Shahul Hamid

Student Works (2000-2009)

The utilization of renewable resources particularly from plant-based industries, such as, in the oleochemical sector makes it possible for further expansion of down-stream process products. However, to remain competitive the pollution generated from this industry should not be taken lightly. Implementation of cleaner technology into the oleochemical process will increase the efficiency of resource utilization of the industry, concurrently reducing quantity of waste generated. Waste audit conducted at Cognis Oleochemical (M) (COM) Sdn. Bhd. indicated that the major process-wastes generated by the facility were glycerol residue (GR) from Cognis Rika (M) Sdn. Bhd. (CRM) and wastewater sludge (WWS) from COM …

Preparation And Characterization Of Lithiated Cathode Materials For Lithium Batteries, Shanti Navaratnam

Student Works (2000-2009)

Four different cathode materials, LiNiO₂, LiCoO₂, LiCo₀.₂ Ni₀.₈O₂ and LiCo₀.₄, Ni₀.₆O₂ were synthesized by sol - gel technique. The prepared materials were characterized X-ray diffraction pattern, FT-IR and cyclic voltammetry. X-ray diffraction pattern shows crystallinity of materials, increases with higher calcination temperature. From FT- IR studies, it was shown, that the purity of sample also increased with prolong heating at higher temperatures. It was possible to obtain pure and highly crystalline LiNiO₂ after heating for fourteen hours at 800°c. Cyclic voltammetry shows the four prepared materials are suitable for fabrication of cathode, as lithium ions can intercalate and de-intercalate. LiNiO₂ …

Comparative Performance Of Wastewater Treatment Plants In Three Rubber Glove Manufacturing Plants, Lee Kuan Loh

Student Works (2000-2009)

During the manufacturing of rubber gloves, water is used as wash water at different stages to clean the rubber gloves, thus generating quite a substantial amount of effluent. There are four main sources of effluent. i.e. a) from the glove formers cleaning tank, which collects the acidified water used to clean these formers, b) latex dipping tank, where it collects wash water used to cool the tank during dipping process and the sludge form the tank itself, c) leaching tank, where it collects wash water used to leach out the pollutants from the gloves and lastly d) latex compounding, containing …

Immobolisation And Biochemical Characterisation Of A Selected Commercially Available Laccase, Chandra Sundaralingam

Student Works (2000-2009)

ln this study, laccase from Novo Nordisk was chosen for biochemical characterization and immobilization investigation. The specific aims of this work was to develop optimum conditions for immobilization of laccase by entrapment method using copper alginate and characterize the laccase biochemically. The pH optimum of the crude enzyme extract was 5.5 and was found to be stable over a wide range of pH values. The apparent molecular weight of this enzyme was around 79,000 Daltons. Three peaks of activity (isoenzymes) were obtained from isoelectric focusing of pH values 4.7, 5.2 and 6.0. The optimum pH of the immobilized laccase by …

Isolation, Screening And Characterisation Of Lactic Acid Bacteria Isolated From Local Food Sources, Ahmad Faris Mohd. Adnan

Student Works (2000-2009)

126 bacterial isolates were isolated from several local food sources. Out of these, 55 isolates were subsequently identified as lactic acid bacteria i.e. they were gram-positive and catalase negative. These 55 isolates were put through gel plug test to distinguish between homofermentative and heterofermentative isolates. 16 of the 55 lactic acid bacteria isolates were found to be homofermentative. From the 16 homofermentative isolates, seven were chosen on the basis of origin and sugars used in the enrichment process for preliminary physiological characterisation. Several conditions were chosen such as variable temperature, lactic acid tolerance, NaCl concentration and initial pH These serve …

Fixed Bed Biosorption Of Cu(Ii) By Immobilized Biomass Of Sargassum Baccularia, Kong Fei Tan

Student Works (2000-2009)

The primary objective of this study was to investigate the feasibility of using the immobilized biomass of Sargassum buccularia. a brown marine macro algae. to remove and recover copper ions in a fixed bed reactor by passive adsorption. This is commonly referred to as biosorpliun. Inactivated biomass of S. baccularia were chemically modified b) immobilizing it onto polyvinyl alcohol (PVA} as a support matrix. Spherical gel beads that were produced in this manner were subjected to mass transfer and equilibrium studies. The biosorption of copper is a bi-phasic process. with an initial fast phase for the first 2 hours followed …

Waste Management In Palm-Oleo Sdn. Bhd, Ramesh Ramasamy

Student Works (2000-2009)

Oleochemical industry in Malaysia has been diversifying significantly due to the availability of raw materials (palm oil) and the high demand for downstream products such as fatty acids, fatty alcohols and glycerine. The growth of oleochemical industries is further enhanced by fluctuations io petroleum price and regular animal diseases, which made tallow-based fats unreliable. Environmental awareness is growing rapidly in Malaysia. There is growing realization of the need to balance industrial and economic development with environmental preservation and protection, as well as, with efficient use of energy sources in order to achieve sustainable development. Extensive waste management studies were focused …

13-C Nmr Analysis Of Soot Produced From Model Compounds And A Coal, Mark S. Solum, Adel F. Sarofim, Ronald J. Pugmire, Thomas H. Fletcher, Haifeng Zhang

Faculty Publications

Soot samples, including the associated organics, produced from an Illinois No. 6 coal (five samples) and two model compounds, biphenyl (three samples) and pyrene (two samples), have been studied by ¹³C NMR methods. The coal soot data served as a guide to selection of the temperature range that would be most fruitful for investigation of the evolution of aerosols composed of soot and tars that are generated from model compounds. The evolution of the different materials in the gas phase followed different paths. The coal derived soots exhibited loss of aliphatic and oxygen functional groups prior to significant growth …

Electrodeposition Of Niw Alloys Into Deep Recesses, Lakshmikanth Namburi

LSU Master's Theses

Pulse electrodeposition has been investigated as a general technique for the electrodeposition of nickel-tungsten alloys in deep recesses for MEMS. Ni-W exhibits an induced codeposition mechanism, where the Ni reaction rate enhances the codeposition of W. Electrodeposition of this alloy has been achieved into recesses of 500 micron deep. The challenges that have been encountered are those related to gas evolving side reactions, local pH rises, diffusional limitations of the soluble species and long times required for filling the recesses. Electrodeposition on cylinder electrodes at different rotation rates was also carried out in order to obtain data on composition of …

Novel Processing Of Hydroxyapatite-Zirconia Composites Using Nano-Sized Particles, Mark R. Towler, I. R. Gibson, S. M. Best

Chemical and Biochemical Engineering Faculty Research & Creative Works

A method to produce composites of hydroxyapatite (HA) with ZrO2 (Y-TZP) additions between 0 and 10 wt % at a low sinter temperature of 750 °C is presented. The method limits the amount of reaction between the HA and ZrO2. A ZrO2 loading level that would improve strength while limiting the decomposition of the HA is studied.

Time-Varying System Identification Using Modulating Functions And Spline Models With Application To Bio-Processes, Sridhar Ungarala, Tomas B. Co

Chemical & Biomedical Engineering Faculty Publications

Time dependent parameters are frequently encountered in many real processes which need to be monitored for process modeling, control and supervision purposes. Modulating functions methods are especially suitable for this task because they use the original continuous-time differential equations and avoid differentiation of noisy signals. Among the many versions of the method available, Pearson–Lee method offers a computationally efficient alternative. In this paper, Pearson–Lee method is generalized for non-stationary continuous-time systems and the on-line version is developed. The time dependent parameters are modeled as polynomial splines inside a moving data window and recursion formulae using shifting properties of …

Solitary Waves And Supersonic Reaction Front In Metastable Solids, Hendrik J. Viljoen, Lee L. Lauderback, D. Sornette

Hendrik J. Viljoen Publications

Motivated by an increasing number of remarkable experimental observations on the role of pressure and shear stress in solid reactions, explosions and detonations, we present a simple toy model that embodies nonlinear elasticity and dispersion as well as chemical or phase transformation. This generalization of the Toda Lattice provides an effective model for the description of the organization during an abrupt transformation in a solid. One of the challenges is to capture both the equilibrium degrees of freedom as well as to quantify the possible role of out-of-equilibrium perturbations. In the Toda Lattice, we verify that the particle velocities converge …

Hybridization Of Dna By Sequential Immobilization Of Oligonucleotides At The Air-Water Interface, Murali Sastry, Vidya Ramakrishnan, Mrunalini Pattarkine, Anand Gole, K. N. Ganesh

Faculty Works

The hybridization of DNA by sequential electrostatic and hydrogen-bonding immobilization of single-stranded complementary oligonucleotides at the air-water interface with cationic Langmuir monolayers is demonstrated. The complexation of the single-stranded DNA molecules with octadecylamine (ODA) Langmuir monolayers was followed in time by monitoring the pressure-area isotherms. A large (and slow) expansion of the ODA monolayer was observed during each stage of complexation in the following sequence: primary single-stranded DNA followed by complementary single-stranded DNA followed by the intercalator, ethidium bromide. Langmuir-Blodgett (LB) films of the ODA-DNA complex were formed on different substrates and characterized using quartz-crystal microgravimetry (QCM), Fourier transform infrared …

The Development Of Carbon Monoxide Tolerant Catalysts For Proton-Exchange Membrane Fuel Cell, Zhong-Jun Hou, Hong-Mei Yu, Bao-Lian Yi, Ming Han

Journal of Electrochemistry

High over-potential of proton exchange membrane fuel cell (PEMFC) anode caused by carbon monnoxide poisoning when reformate or methanol is used as fuel is main obstacle to the high performance of PEMFCs. Using carbon monoxide tolerant catalysts is the most hopeful way to solve the CO problem. The CO poisoning problem is reviewed briefly in this paper, and the development of CO tolerant catalysts is introduced in details, including electrocatalysts activity, preparation method and mechanism of tolerance to CO.Mo and W can improve catalysts' CO tolerance. Multi-component catalysts are expected to be more tolerant to CO.

Studies Of Adsorption And Oxidation Of Ethanol On Nm-Pt/Gc Electrode——I. Cyclic Voltammograms And In-Situ Ftir Spectroscopy In Alkaline Media, Guo-Lian Chen, Shi-Gang Sun, Sheng-Pei Chen, Zhi-You Zhou

Journal of Electrochemistry

The electro-oxidation of ethanol on nm-Pt/GC electrode in alkaline solutions containing 0.02 mol·L^-1 NaOH+0.1 mol·L^-1 CH₃CH₂OH was investigated by using cyclic voltammetry and in-situ FTIR spectroscopy. The experimental results demonstrated that the main product of ethanol oxidation is CH₃COO^-, only very small amount of CH ³CHO has been determined simultaneously. In contrast with the dual path reaction mechanism for the oxidation of ethanol in acid media, the oxidation of ethanol in alkaline media didn't pass through the dissociative adsorption, and no adsorbed species could be determined even using a …

Investigation Of A Complex Lithium Cobalt Nickel Oxide As Lithium Ion Battery Cathode Materials Prepared By A New Citrate Sol-Gel Method, Jing-Li Han, Qing-Guo Liu

Journal of Electrochemistry

The synthesis and electrochemical characteristics of lithium cobalt nickel oxide as cathode materials for rechargeable lithium batteries were investigated. It was clarified from these investigations that lithium cobalt nickel oxide has been produced from basic cobalt carbonate,basic nickel carbonate, lithium carbonate, and citrate. LiNi_0.8Co _0.2O₂ prepared under the stream of oxygen gas showed a higher cycling capacity of (～190 mAh·g^-1).

Template Synthesis Of Nano-Structured Electrode Materials And Its Electrochemical Performance, Jian Zhao, Quan-Yong Gao, Yong Yang, Zu-Geng Lin

Journal of Electrochemistry

In this letter, various nano structured materials such as spinel LiMn₂O₄ nanotubes/nanowires and carbon nanotubes have been prepared by using porous alumina template. The prepared template and materials have been characterized by AFM and TEM techniques. It is shown that size of the nanotubes can be conveniently controlled by using template method. Some preliminary results of cyclic voltammetry about nano structured LiMn₂O₄ are also reported.